Highly Selective Salicylate Membrane Electrode Based on N,N＇- （Aminoethyl）ethylenediamide Bis（2-salicylideneimine） Binuclear Copper（Ⅱ） Complex as Neutral Carrier

A new ion selective electrode for salicylate based on N,N＇-（aminoethyl）ethylenediamide bis（2-salicylideneimine） binuclear copper（Ⅱ） complex [Cu（Ⅱ）2-AEBS] as an ionophore was developed. The electrode has a linear range from 1.0 × 10^-1 to 5.0 ×10^-7 mol·L^- 1 with a near-Nemstian slope of （ - 55 ±1 ） mV/decade and a detection limit of 2.0 × 10-7 mol·L^-1 in phosphorate buffer solution of pH 5.0 at 25 ℃. It shows good selectivity for Sal^- and displays anti-Hofmeister selectivity sequence： Sal^-〉SCN^-〉 ClO4^- 〉I^-〉 NO2^- 〉Br^-〉 NO3^- 〉Cl^-〉 SO3^2- 〉 SO4^2- The proposed sensor based on binuclear copper（Ⅱ）complex has a fast response time of 5-10 s and can be used for at least 2 months without any major deviation. The response mechanism is discussed in view of the alternating current （AC） impedance technique and the UV-vis spectroscopy technique. The effect of the electrode membrane compositions and the experimental conditions were studied. The electrode has been successfully used for the determination of salicylate ion in drug pharmaceutical preparations.     

Determination of Inorganic Arsenic Species by Electrochemical Hydride Generation Atomic Absorption Spectrometry with Selective Electrochemical Reduction

A new direct procedure for the determination of inorganic arsenic species was developed by electrochemical hydride generation atomic absorption spectrometry （EcHG-AAS） with selective electrochemical reduction. The determination of inorganic arsenic species is based on the fact that As（Ⅲ） shows significantly higher absorbance at low electrolytic currents than As（Ⅴ） in 0.3 mol·L^-1 H2SO4. The electrolytic current used for the determination of As（Ⅲ） without considerable interferences of As（Ⅴ） was 0.4 A, whereas the current for the determination of As（Ⅲ） and As（Ⅴ） was 1.2 A. For equal concentrations of As（Ⅲ） and As（Ⅴ） in a sample, the interferences of As（Ⅴ） during the As（Ⅲ） determination were smaller than 5%. The absorbance for As（Ⅴ） could be calculated by subtracting that for As（Ⅲ） measured at 0.4 A from the total absorbance for As（Ⅲ） and As（Ⅴ） measured at 1.2 A, and then the concentration of As（Ⅴ） can be obtained by its calibration curve at 1.2 A. The methodology developed provided the detection limits of 0.3 and 0.6 ng·mL^-1 for As（Ⅲ） and As（Ⅴ）, respectively. The relative standard deviations were of 3.5% for 20 ng·mL^-1 As（Ⅲ） and 3.2% for 20 ng·mL^-1 As（Ⅴ）. The method was successfully applied to determination of soluble inorganic arsenic species in Chinese medicine.     

Kinetics and Mechanism of Iridium（Ⅲ）-Catalyzed Oxidation of Ethanol Amine by Cerium（ Ⅳ ） in Sulfuric Acid Media

In this study, the kinetics and mechanism of the iridium(Ⅲ)-catalyzed oxidation of ethanol amine(EAN) by cerium(Ⅳ) in a sulfuric acid medium was investigated using titrimetric technique of redox in a temperature range of 298—313 K. It was found that the reaction is of first order with respect to Ce(Ⅳ) and Ir(Ⅲ), and a positive fractional order with respect to EAN. It was also found that the pseudo-first-order([EAN][Ce(Ⅳ)]) rate constant kobs decreases with the increase of [H ] and [HSO-4]. Under the protection of nitrogen gas, the reaction system can initiate the polymerization of acrylonitrile, indicating the generation of free radicals. On the basis of the experimental results, a suitable mechanism was proposed. From the dependence of kobs on the concentration of hydrogen sulfate, Ce(SO4)2 was found to be the kinetically active species. The rate constants of the rate-determining step together with the activation parameters were evaluated.     

A New Amperometric Biosensor Based on HRP/Nano-Au/L-Cysteine/Poly（o-Aminobenzoic acid）-Membrane-Modified Platinum Electrode for the Determination of Hydrogen Peroxide

The third generation amperometric biosensor for the determination of hydrogen peroxide （H2O2） has been described. For the fabrication of biosensor, o-aminobenzoic acid （oABA） was first electropolymerized on the surface of platinum （Pt） electrode as an electrostatic repulsion layer to reject interferences. Horseradish peroxidase （HRP） absorbed by nano-scaled particulate gold （nano-Au） was immobilized on the electrode modified with polymerized o-aminobenzoic acid （poABA） with L-cysteine as a linker to prepare a biosensor for the detection of H2O2. Amperometric detection of H2O2 was realized at a potential of ＋20 mV versus SCE. The resulting biosensor exhibited fast response, excellent reproducibility and sensibility, expanded linear range and low interferences. Temperature and pH dependence and stability of the sensor were investigated. The optimal sensor gave a linear response in the range of 2.99×10^-6 to 3.55×10^-3 mol·L^-1 to H2O2 with a sensibility of 0.0177 A·L^-1·mol^-1 and a detection limit （S/N = 3） of 4.3×10^-7 mol·L^-1. The biosensor demonstrated a 95% response within less than 10 s.     

Electrodeposition of Silver Nanoparticles on MWCNT Film Electrodes for Hydrogen Peroxide Sensing

Silver （Ag） nanoparticles were directly electrodeposited on multi-walled carbon nanotubes （MWCNT） in AgNO3/LiNO3 containing EDTA （ethylenediaminetetraacetic acid）. The structure and nature of the resulting Ag/MWNT composite were characterized by field emission scanning electron microscopy （FE-SEM）, transmission electron microscopy （TEM） and X-ray diffraction （XRD）, and the distribution shape of Ag nanoparticles was found to be dependent on the presence of EDTA. The modified electrode showed excellent electrocatalytic activity to redox reaction of hydrogen peroxide and the mechanism of hydrogen peroxide was partly reversible procession with oxidation and reduction peaks at 0.77 and -0.83 V, respectively. The oxidation and reduction peak currents were linearly related to hydrogen peroxide concentration in the range of 1×10^-6-3×10^-4 and 1 ×10^-8-7× 10^-4 mol·L^-1 with correlation coefficients of 0.996 and 0.986, and 3s-detection limit of 9 × 10^-7 and 7 × 10^-9 mol·L^-1.     

四种钌（Ⅱ）配合物的中心离子电化学行为的比较

The electrochemical behavior of mononuclear and symmetrical binuclear ruthenium（Ⅱ） complexes [Ru1:Ru(bpy)2DIPB(ClO4)2,Ru2:(bpy)2 Ru(DIPB)Ru(bpy)2(ClO4)4,Ru3:Ru(phen)2DIPB(ClO4)2 and Ru4:(phen)2 Ru(DIPB)Ru (phen)2(ClO4)4] containing binuclear ligand 2,2′-bipyridine(bpy),1,10-phenanthroline(phen) and bridging ligand 1,4-di-[2-imidazo[4,5-f][1,10] phenanthroine benzene(DIPB) on a platinum electrode and the intermetallic interaction of binuclear complexes have been investigated using cyclic voltammetry,cyclic ac voltammetry and differential capacitance techniques,etc.In acetonitrile solution with a concentration of 0.1 mol穌m-3 TBAP,the central ions in four complexes all display single 1e and 2e reversible oxidation- reduction waves on the cyclic voltammograms,with apparent diffusion coefficients of the mononuclear complexed cations being larger than that of the binuclear ones.The apparent diffusion coefficients for complexed cations with auxiliary ligands bpy are also found to be larger than that with ligands phen.It appears that the overlapping of two continuous single-electron processes by cyclic ac voltammetry and differential capacitance techniques occurs during the redox processes of the central ions binuclear complexes.The results show that a weak electronic interaction exits between the two central ruthenium ions in binuclear complexes.     

纳米TiO2膜用于光催化氧化测定化学需氧量的研究

A photocatalytic oxidation method for determination of chemical oxygen demand （COD） using nano-TiO2 film, based on the use of a nano-TiO2-Ce（SO4）2 system and electrochemical detection, was proposed. The technique was originated from the direct determination of the Ce（Ⅲ） concentration change resulting from photocatalytic oxidation of organic compounds. Ce（Ⅲ）, which was produced by photocatalytic reduction of Ce（SO4）2, could be measured at a multi-walled carbon nanotubes （MWNT） chemically modified electrode （CME）. The COD values by this method were calculated from the differential pulse voltammetry （DPV） current of Ce（Ⅲ） at the CME. Under the optimal operation conditions, the detection limit of 0.5 mg·L^-1 COD with the linear range of 1-600 mg·L^-1 was achieved. This method was also applied to determination of various COD of ground water and wastewater samples. The resuits were in good agreement with those from the conventional COD methods, i.e., permanganate and dichromate ones.     

Thermal Degradation Kinetics of N,N＇-Di（diethoxythiophosphoryl）-1,4-phenylenediamine

The non-isothermal degradation kinetics of N,N＇-di（diethoxythiophosphoryl）-1,4-phenylenediamine in N2 was studied by TG-DTG techniques.The kinetic parameters,including the activation energy and pre-exponential factor of the degradation process for the title compound were calculated by means of the Kissinger and Flynn-Wall-Ozawa（FWO）method and the thermal degradation mechanism of the title compound was also studied with the Satava-Sestak methods.The results indicate that the activation energy and pre-exponential factor are 152.61 kJ/mol and 9.06×101 4s -1with the Kissinger method and 154.08 kJ/mol with the Flynn-Wall-Ozawa method,respectively.It has been shown that the degradation of the title compound follows a kinetic model of one-dimensional diffusion or parabolic law,the kinetic function is G（α）=α2and the reaction order is n=2.     

Electrochemical Reaction Mechanism of Phenacetin at a Carboxylated Multiwall Carbon Nanotube Modified Electrode and Its Analytical Applications

A novel type of carboxylated multiwalled carbon nanotube modified electrode（c-MWCNTs/GCE） was constructed and the electrochemical properties of phenacetin（PHE） at it were studied. In a buffer solution of 0.1 mol/L HAc-NaAc（pH=5.3）, PHE exhibited a couple of quasi-reversible redox peaks and an anodic peak in the poten- tial range of 0.2--1.2 V at c-MWCNTs/GCE. The peak current was proportional to the concentration of PHE in the range of 4.0× 10^-6_ 1.0 × 10^-4 mol/L with a detection limit of 1.0× 10^-6 mol/L（S/N=3）. The c-MWCNTs/GCE showed excellent repeatability and stability and the electrochemical reaction mechanism of PHE was proposed. This method was used to determine the content of PHE in medical tablets and the recovery was determined to be 96.5%--104.2% by means of a standard addition method.     

Kinetics and Mechanism of Iridium(Ⅲ)-Catalyzed Oxidation of Ethanol Amine by Cerium(Ⅳ) in Sulfuric Acid Media

In this study, the kinetics and mechanism of the iridium(Ⅲ)-catalyzed oxidation of ethanol amine(EAN) by cerium(Ⅳ) in a sulfuric acid medium was investigated using titrimetric technique of redox in a temperature range of 298-313 K. It was found that the reaction is of first order with respect to Ce(Ⅳ) and Ir(Ⅲ), and a positive fractional order with respect to EAN. It was also found that the pseudo-first-order([EAN](》)[Ce(Ⅳ)]) rate constant kobs decreases with the increase of [H ] and [HSO-4]. Under the protection of nitrogen gas, the reaction system can initiate the polymerization of acrylonitrile, indicating the generation of free radicals. On the basis of the experimental results, a suitable mechanism was proposed. From the dependence of kobs on the concentration of hydrogen sulfate, Ce(SO4)2 was found to be the kinetically active species. The rate constants of the rate-determining step together with the activation parameters were evaluated.     

Micellar Catalysis on the Redox Reaction of Ascorbic Acid-Vanadium(V) System

Stoichiometry of the redox reaction of vanadium(V) by ascorbic acid (H₂A) has been experimentally determined to be H₂A + 2V(V) → A + 2V(IV) + 2H ⁺ . Evidence of induced polymerization of acrylonitrile and the reduction of mercuric chloride indicates that a free-radical mechanism operates during the course of reaction. Vanadium(V) is only reduced to vanadium(IV). The kinetics of this redox reaction have been investigated spectrophotometrically at 35°C in acidic media of H₂SO₄. In this kinetic study we have observed the nature of vanadium(V)-H₂A interaction in presence of anionic surfactant of SDS. In V(V)-H₂A system, the addition of anionic surfactant (SDS) enhanced the reaction rate and shows catalytic effect. This trend was explained by the incorporation/solubilization of vanadium(V) and ascorbic acid in the Stern layer.     

Effect of specific adsorbed anions on the electrode kinetics of the V(III)/V(II) and Eu(III)/Eu(II) couples

Electrochemical kinetic parameters of the V(III)/V(II) and Eu(III)/Eu(II) couples in sulfuric, perchloric, hydrochloric, and hydrobromic acids were measured by potentiostatic and double pulse galvanostatic methods. The ₂ potentials in these solutions were calculated from electrocapillary measurements and the effect of the ₂ potentials on the electrode kinetics was discussed. The kinetic data after the Frumkin correction was applied show a very good agreement in H₂SO₄, HClO₄, and HCl solutions, if we assume that the non-complexed ion, which is partially supplied by the dissociation of complex ions, participates in the electrode reaction. The corrected rate constants in the bromide solution were about ten times larger than those to be expected from the ₂ potentials in the case of the V(III)/V(II) couple and a small acceleration effect was observed for the Eu(III)/Eu(II) couple. The greater reaction rate in the bromide solution is explained by the bridging effect.     

全钒液流电池高浓度下V(IV)/V(V)的电极过程研究

采用循环伏安、低速线性扫描和阻抗技术, 以石墨为电极, 研究了V(IV)/V(V)在较高浓度下的电极过程. 结果表明, 采用2.0 mol•L-1 的V(IV)溶液时, H2SO4浓度低于2 mol•L-1, V(IV)/V(V)反应极化大, 可逆性差, 表现为电化学和扩散混合控制; H2SO4浓度增至2 mol•L-1以上, V(IV)/V(V)反应的可逆性提高, 转为扩散控制, 且增加H2SO4浓度有利于阻抗的降低; 但H2SO4浓度超过3 mol•L-1, 溶液的粘度和传质阻力大, 阻抗反而增大. 在3 mol•L-1的H2SO4中, 随着V(IV)浓度的增加, 体系的可逆性和动力学改善, 阻抗减小; 但V(IV)浓度超过2.0 mol•L-1, 较高的溶液粘度导致溶液的传质阻力迅速增加, V(IV)/ V(V)的电化学性能衰减, 阻抗增大. 因此, 综合考虑电极反应动力学和电池的能量密度两因素, V(IV)溶液的最佳浓度为1.5～2.0 mol•L-1, H2SO4浓度为3 mol•L-1.     

A Comparative Study of Functionalized High‐Purity Carbon Nanotubes towards the V(IV)/V(V) Redox Reaction Using Cyclic Voltammetry and Scanning Electrochemical Microscopy

Functionalized high purity carbon nanotubes (CNTs) with various amounts of oxygen containing surface groups were investigated towards the relevant redox reactions of the all‐vanadium redox flow battery. The quinone/hydroquinone redox peaks between 0.0 and 0.7 V vs. Ag|AgCl|KCl_sat. were used to quantifying the degree of functionalization and correlated to XPS results. Cyclic voltammetry in vanadyl sulfate‐containing 3 M H₂SO₄ as a common supporting electrolyte showed no influence of the amount of surface groups on the V(IV)/V(V) redox system. In contrast, the reactions occurring at the negative electrode (V(II)/V(III) and V(III)/V(IV)) are strongly affected by oxygen surface groups. However, under modified experimental conditions, SECM experiments detecting the consumption of VO²⁺ molecules by CNT thin films in pH=2 solution show improved onset potentials with increased surface oxygen content up to ∼ 3 at%. Further increase in surface oxygen up to 8 at% led to minor improvement. These dissimilar results under different experimental conditions are rationalized by suggesting that oxygen functional groups do not form the active site for the V(IV)/V(V) reaction but wetting of the catalyst layer is of high importance.     

Nanoporous Pt Catalyst Modified by Sn Electrodeposition for Electrochemical Oxidation of Formaldehyde

A nanoporous Pt particles‐modified Ti (nanoPt/Ti) electrode was prepared through a simple hydrothermal method using aqueous H₂PtCl₆ as a precursor and formaldehyde as a reduction agent. The nanoPt/Ti electrode was then modified with limited amounts of tin particles generated by cyclic potential scans in the range of ?0.20 to 0.50 V in a 0.01 mol·L^?1 SnCl₂ solution, to synthesize a Sn‐modified nanoporous Pt catalyst (Sn/nanoPt/Ti). Electroactivity of the nanoPt/Ti and Sn/nanoPt/Ti electrodes towards formaldehyde oxidation in a 0.5 mol·L^?1 H₂SO₄ solution was evaluated by cyclic voltammetry and chronoamperometry. Electrooxidation of formaldehyde on the nanoPt/Ti electrode takes place at a potential of 0.45 V and then presents high anodic current densities due to the large real surface area of the nanoPt/Ti electrode. The formaldehyde oxidation rate is dramatically increased on the Sn/nanoPt/Ti electrode at the most negative potentials, where anodic formaldehyde oxidation is completely suppressed on the nanoPt/Ti electrode. Chronoamperogramms (CA) of the Sn/nanoPt/Ti electrode display stable and large quasi‐steady state current densities at more negative potential steps. Amperometric data obtained at a potential step of 100 mV show a linear dependence of the current density for formaldehyde oxidation upon formaldehyde concentration in the range of 0.003 to 0.1 mol·L^?1 with a sensitivity of 59.29 mA·cm^?2 (mol·L^?1)^?1. A detection limit of 0.506 mmol·L^?1 formaldehyde was found. The superior electroactivity of the Sn/nanoPt/Ti electrode for formaldehyde oxidation can be illustrated by a so‐called bifunctional mechanism which is involved in the oxidation of poisoning adsorbed CO species via the surface reaction with OH adsorbed on neighboring Sn sites.     

A selenium-bonded oxorhenium(V) complex: solvothermal synthesis,structural characterization,and electrochemical behavior

The solvothermal reaction of [ReOCl₃(PPh₃)₂] with 2,2′-seleno-bis(4,6-di-tert-butylphenol) (H₂L¹) in ethanol at 95 °C resulted in an oxorhenium(V) complex of formulation [ReO(L¹)(L²)] due to the in situ formation of 2-selenochloromethyl-4,6-di-tert-butylphenolate (L²) through the cleavage of one C–Se bond of H₂L¹. The mononuclear oxorhenium(V) complex was characterized by physicochemical and spectroscopic methods along with detailed structural analysis by single crystal X-ray crystallography. Electrochemical studies revealed a one-electron equivalent quasi-reversible voltammogram for the ReO(V)/ReO(VI) redox couple at 1.28 V (versus SCE) with no cathodic response for ReO(V) → ReO(IV) reduction.     

Nucleic Acid Biosensor for Detection of Human Immunodeficiency Virus Using Aquabis(1,10‐phenanthroline)copper(II) Perchlorate as Electrochemical Indicator

The electrochemical behavior of aquabis(1,10‐phenanthroline)copper(II) perchlorate [Cu(H₂O)(phen)₂]·2ClO₄, where phen=1,10‐phenanthroline, on binding to DNA at a glassy carbon electrode (GCE) and in solution, was described. Cyclic voltammetry (CV) and differential pulse voltammetry (DPV) results showed that [Cu(H₂O)(phen)₂]²⁺ had excellent electrochemical activity on the GCE with a couple of quasi‐reversible redox peaks. The interaction mode between [Cu(H₂O)(phen)₂]²⁺ and double‐strand DNA (dsDNA) was identified to be intercalative binding. An electrochemical DNA biosensor was developed with covalent immobilization of human immunodeficiency virus (HIV) probe for single‐strand DNA (ssDNA) on the modified GCE. Numerous factors affecting the probe immobilization, target hybridization, and indicator binding reactions were optimized to maximize the sensitivity and speed of the assay. With this approach, a sequence of the HIV could be quantified over the range from 7.8×10^?9 to 3.1×10^?7 mol·L^?1 with a linear correlation of γ=0.9987 and a detection limit of 1.3×10^?9 mol·L^?1.     

Binary and ternary oxorhenium(V) complexes: synthesis,characterization, and crystal structure

A series of anionic five-coordinate binary oxorhenium(V) complexes with dithiolato ligands, Bu₄N[ReO(L¹)₂] (1a), Bu₄N[ReO(L²)₂] (1b), and Bu₄N[ReO(L³)₂] (1c), and a series of neutral octahedral ternary oxorhenium(V) complexes of mixed dithiolato and bipyridine ligands, [ReO(L¹)(bpy)Cl] (2a), [ReO(L²)(bpy)Cl] (2b), and [ReO(L³)(bpy)Cl] (2c) (where L¹H₂ = ethane-1,2-dithiol, L²H₂ = propane-1,3-dithiol, L³H₂ = toluene-3,4-dithiol, and bpy = 2,2′-bipyridine), were isolated and characterized by physicochemical and spectroscopic methods. The solid state structure of 1c was established by X-ray crystallography. All the mononuclear oxorhenium(V) complexes are diamagnetic. The redox behavior of all the complexes has been studied voltammetrically.     

二甲醚电氧化增强电化学表面积的研究(英)

0IntroductionFuel cells em ploying polym er(e.g.,N afion m em-branes)as the electrolyte are receiving increasing at-tention.The m em brane-electrode assem bly(M EA),com prising of a proton conducting m em brane sand-wiched between tw o gas diffusion elect…     

Direct Electrochemistry and Electrocatalysis of Hemoglobin Based on Nafion‐Room Temperature Ionic Liquids‐Multiwalled Carbon Nanotubes Composite Film

A robust and effective composite film combined the benefits of Nafion, room temperature ionic liquid (RTIL) and multi‐wall carbon nanotubes (MWNTs) was prepared. Hemoglobin (Hb) was successfully immobilized on glassy carbon electrode surface by entrapping in the composite film. Direct electrochemistry and electrocatalysis of immobilized Hb were investigated in detail. A pair of well‐defined and quasi‐reversible redox peaks of Hb was obtained in 0.10 mol·L^?1 pH 7.0 phosphate buffer solution (PBS), indicating that the Nafion‐RTIL‐MWNTs film showed an obvious promotion for the direct electron transfer between Hb and the underlying electrode. The immobilized Hb exhibited an excellent electrocatalytic activity towards the reduction of H₂O₂. The catalysis current was linear to H₂O₂ concentration in the range of 2.0×10^?6 to 2.5×10^?4 mol·L^?1, with a detection limit of 8.0×10^?7 mol·L^?1 (S/N=3). The apparent Michaelis‐Menten constant (K_m^app) was calculated to be 0.34 mmol·L^?1. Moreover, the modified electrode displayed a good stability and reproducibility. Based on the composite film, a third‐generation reagentless biosensor could be constructed for the determination of H₂O₂.