亲水作用色谱柱与阳离子交换树脂柱结合分离无机离子（英文）

A combination of hydrophilic interaction chromatographic(HILIC) column and a weakly acidic cation-exchange resin(WCX) column was used for simultaneous separation of inorganic anions and cations by ion chromatography(IC).Firstly,the capability of HILIC column for the separation of analyte ions was evaluated under acidic eluent conditions.The columns used were SeQuant ZIC-HILIC(ZIC-HILIC) with a sulfobetaine-zwitterion stationary phase(ZIC-HILIC) and Acclaim HILIC-10 with a diol stationary phase(HILIC-10).When using tartaric acid as the eluent,the HILIC columns indicated strong retentions for anions,based on ion-pair interaction.Especially,HILIC-10 could strongly retain anions compared with ZIC-HILIC.The selectivity for analyte anions of HILIC-10 with 5 mmol/L tartaric acid eluent was in the order of I-> NO-3 > Br-> Cl-> H2PO-4.However,since HILIC-10 could not separate analyte cations,a WCX column(TSKgel Super IC-A/C) was connected after the HILIC column in series.The combination column system of HILIC and WCX columns could successfully separate ten ions(Na+,NH+4,K+,Mg2+,Ca2+,H2PO-4,Cl-,Br-,NO-3 and I-) with elution of 4 mmol/L tartaric acid plus 8 mmol/L 18-crown-6.The relative standard deviations(RSDs) of analyte ions by the system were in the ranges of 0.02%-0.05% in retention times and 0.18%-5.3% in peak areas through three-time successive injections.The limits of detection at signal-to-noise ratio of 3 were 0.24-0.30 μmol/L for the cations and 0.31-1.2 μmol/L for the anions.This system was applied for the simultaneous determination of the cations and the anions in a vegetable juice sample with satisfactory results.     

Detection of complement C4 with a piezoelectric immunosensor

A piezoelectric immunosensor has been developed for the detection of complement C4. Anti-C4 antibody was immobilized onto the gold electrodes of a 9 MHz AT-cut piezoelectric crystal. The coated crystal with the physical adsorption method to immobilize antibody showed the better results than the polyethyleneimine adhesion, glutaraldehyde cross-linking method with respect to sensitivity and reproducibility. The antibody-bound crystal with the physical adsorption method was successfully used for the detection of human complement C4 in the concentration range of 0.1-10 μg/mL for 40 min incubation time. The immunosensor system had good selectivity, and other materials in human serum did not interfere the detection remarkably. The crystal could be regenerated nearly 15 times when the bound materials on the crystal surface were eluted by strong acid and strong alkali solutions and subsequently cleaned in a ultrasonic cleaner.     

Synthesis of a Pair of Derivatives of N-Methylpyrrole Polyamide

A pair of derivatives of tetrameric N-methylpyrrole polyamide were synthesized in order to develop a new method for the study of interaction of the polyamide derivatives with DNA. Indole acetic acid and nicotinic acid were introduced to the polyamide in the synthesized compound, which showed an expected red shift in the UV spectrum. These compounds may function as a potential tool in the detection of the polyamide binding to DNA.     

Preparation of polymer-supported phosphine from ferrocene for palladium-catalyzed Suzuki-Miyaura cross-coupling reactions

Polymer-supported phosphine ligand 3b derived from ferrocene was prepared,and applied in palladium-catalyzed Suzuki- Miyaura reactions.A range of aryl bromides can couple with phenylboronic acid to obtain corresponding biaryls in excellent yields. The recycling of the polymer-bound catalyst was tested without adding palladium.     

Study on the Synthesis of Phenylacetic Acid by Carbonylation of Benzyl Chloride under Normal Pressure

The influences of some factors on the yield of phenylacetic acid in the carbonylation of benzyl chloride were studied in this paper. These factors included the variety and content of catalyst, and that of solvent, way of material feeding, reaction temperature, sodium hydrate concentration, triphenylphosphine content, presence of surfactant, the ratio of organic phase volume to aqueous phase volume etc. The optimum reaction conditions were found to be: with a one-time pour of 0.15g Pd(PPh3)2Cl2, 0.24g PPh3, 75ml NaOH of 3.5mol/L, 20ml benzyl chloride and 55ml n-butyl alcohol, and the reaction was carried out at 50℃ for about 3 hours. The as-obtained yield of phenylacetic acid was as high as 97.6%. In addition, the influences of the presence of phenylacetic acid and air in the reaction system were also studied. The results showed that the presence of air in the system and the entrainment of phenylacetic acid in the circulating organic phase had great influence on the reaction rate, the stability and performance of catalyst and the yield of phenylacetic acid.     

Conversion of xylose and xylan into furfural in biorenewable choline chloride–oxalic acid deep eutectic solvent with the addition of metal chloride

An environmentally benign processing approach for furfural production from xylose and xylan under very mild conditions(353–373 K) was developed with the addition of metal chlorides in ChCl–oxalic acid(a deep eutectic solvent(DES)) synthesized from cheap and renewable starting materials). ChCl–oxalic acid acted as both a Br?nsted acid catalyst and a reaction medium in this catalytic route. In addition, a biphasic system with methyl isobutyl ketone as an extracting reagent(DES/MIBK) to further increase furfural yield was also proposed. This processing approach for producing furfural eliminated the large energy consumption for high pressure saturated steam and the generation of acidic effluent, which was very difficult to handle. The whole catalytic system was more environmentally friendly compared with the commercial process for furfural production.     

添加物对1-甲氧基-2-丙醇催化氧化制甲氧基丙酮反应的影响

The system W Ⅵ H 2O 2 has good selectivity for methoxyacetone in oxidation of 1 methoxy 2 propanol. The effects of acid and base additives on selectivity for methoxyacetone were studied. The results showed that the acid additive, i.e. NaHSO 4, was favorable to Na 2WO 4 H 2O 2 system, while the base additive NEt 3 was favorable to other tungsten compounds. A 71 2% of yield of methoxyacetone with 98 9% of selectivity for methoxyacetone was obtained in Na 2WO 4 H 2O 2 NaHSO 4 MeCOMe oxidation system.     

Suzuki Reaction of Aryl Bromides Using a Phosphine-Free Magnetic Nanoparticle-Supported Palladium Catalyst

A palladium catalyst immobilized on superparaganetic nanoparticles was prepared with a palladium loading of 0.30 mmol/g. The catalyst was characterized using X-ray diffraction, scanning electron microscopy, transmission electron microscopy, vibrating sample magnetometry, thermogravimetric analysis, Fourier transform infrared, atomic absorption spectrophotometry, and nitrogen adsorption. The immobilized palladium catalyst was an efficient catalyst without added phosphine ligands for the Suzuki cross-coupling reaction of several aryl bromides with phenylboronic acid. The recovery of catalyst was simply by magnetic decantation in the presence of a magnet. The immobilized palladium catalyst can be reused many times without significant degradation in catalytic activity. No leaching of active palladium species into the reaction solution was detected.     

Highly Efficient Pd/C-Catalyzed Suzuki Coupling Reaction of p-（un）Substituted Phenyl Halide with （p-Substituted phenyl） Boronic Acid

A highly efficient Pd/C-catalyzed ligandless, heterogeneous Suzuki reaction of p-（un）substituted phenyl halide with （p-substituted phenyl）boronic acid in DMF/H2O solvent in a short reaction time （0.5 h） at 75 ℃ was developed. The key for such a catalytic system was the addition of 1 equivalent of tetrabutylammonium bromide. A wide variety of substituents can be tolerated and high yields of cross coupling products were achieved. The palladium catalyst can be easily recovered and reused without significantly decreasing its efficiency.     

Chemo-enzymatic Synthesis of Z-Asp-Val-Tyr-NH_2——A Precursor Tripeptide of Thymopentin

Z-Asp-Val-Tyr-NH2,a precursor tripeptide of thymopentin(TP-5),was successfully synthesized by a combination of chemical and enzyme methods.Firstly,the precursor dipeptide Val-Tyr-NH2 was synthesized by a novel chemical method in four steps including the preparation of NCA-Val,the esterification of L-tyrosine and the ammonolysis of L-tyrosine ethyl ester,and the formation of Val-Tyr-NH2 from NCA-Val and L-Tyr-NH2.Secondly,a thermolysin,thermoase PC 10F was used to catalyze the formation of Z-Asp-Val-Tyr-NH2 in an aqueous/organic solvent diphase system with Z-Asp-OH and Val-Ty-NH2 as the substrates under thermodynamic control.The optimum conditions were pH=6.5,40 ℃,thermoase 100 mg,in 2-(N-morpholino) ethanesulfonic acid MES/NaOH(containing 5 mmol/L CaCl2) of n-butanol system(15/85,volume ratio) for 20 h in a maximum yield of 27.02%.     

Synthesis of α‐(Fluorophenyl)pyridine by Palladium‐Catalyzed Cross‐Coupling Reaction

A series of α‐(fluoro‐substituted phenyl)pyridines have been synthesized by means of a palladium‐catalyzed cross‐coupling reaction between fluoro‐substituted phenylboronic acid and 2‐bromopyridine or its derivatives. The reactivities of the phenylboronic acids containing di‐ and tri‐fluoro substituents with α‐pyridyl bromide were investigated in different catalyst systems. Unsuccessful results were observed in the Pd/C and PPh₃ catalyst system due to phenylboronic acid containing electron‐withdrawing F atom(s). For the catalyst system of Pd(OAc)₂/PPh₃, the reactions gave moderate yields of 55% –80%, meanwhile, affording 10% –20% of dimerisation (self‐coupling) by‐products, but trace products were obtained in coupling with 2,4‐difluorophenylboronic acids because of steric hinderance. Pd(PPh₃)₄ was more reactive for boronic acids with sterically hindering F atom(s), and the coupling reactions gave good yields of 90% and 91% without any self‐coupling by‐product.     

Kinetic Studies on the Palladium(II)‐Catalyzed Oxidative Cross‐Coupling of Thiophenes with Arylboron Compounds and Their Mechanistic Implications

Reaction orders for the key components in the palladium(II)‐catalyzed oxidative cross‐coupling between phenylboronic acid and ethyl thiophen‐3‐yl acetate were obtained by the method of initial rates. It turned out that the reaction rate not only depended on the concentration of palladium trifluoroacetate (reaction order: 0.97) and phenylboronic acid (reaction order: 1.26), but also on the concentration of the thiophene (reaction order: 0.55) and silver oxide (reaction order: ?1.27). NMR spectroscopy titration studies established the existence of 1:1 complexes between the silver salt and both phenylboronic acid and ethyl thiophen‐3‐yl acetate. A low inverse kinetic isotope effect (k_H/k_D=0.93) was determined upon employing the 4‐deuterated isotopomer of ethyl thiophen‐3‐yl acetate and monitoring its reaction to the 4‐phenyl‐substituted product. A Hammett analysis performed with para‐substituted 2‐phenylthiophenes gave a negative ρ value for oxidative cross‐coupling with phenylboronic acid. Based on the kinetic data and additional evidence, a mechanism is suggested that invokes transfer of the phenyl group from phenylboronic acid to a 1:1 complex of palladium trifluoroacetate and thiophene as the rate‐determining step. Proposals for the structure of relevant intermediates are made and discussed.     

Water‐Soluble and Recyclable Cyclopalladated Ferrocenylimine for Suzuki Coupling Reaction

A series of new water‐soluble cyclopalladated ferrocenylimines were designed and prepared. They were efficient catalyst for Suzuki coupling reactions of aryl bromides and phenylboronic acid in neat water under ambient atmosphere. Among of these catalysts, the catalyst ( C₂D ) could be reused for 6 times for the Suzuki coupling reaction of 4‐bromotoluene with phenylboronic acid in EtOH/H₂O under ambient atmosphere, in which no significant loss activity of C₂D was observed.     

Exploring Regioselective Bond Cleavage and Cross‐Coupling Reactions using a Low‐Valent Nickel Complex

Recently, esters have received much attention as transmetalation partners for cross‐coupling reactions. Herein, we report a systematic study of the reactivity of a series of esters and thioesters with [{(dtbpe)Ni}₂(μ‐η²:η²‐C₆H₆)] (dtbpe=1,2‐bis(di‐tert‐butyl)phosphinoethane), which is a source of (dtbpe)nickel(0). Trifluoromethylthioesters were found to form η²‐carbonyl complexes. In contrast, acetylthioesters underwent rapid C_acyl?S bond cleavage followed by decarbonylation to generate methylnickel complexes. This decarbonylation could be pushed backwards by the addition of CO, allowing for regeneration of the thioester. Most of the thioester complexes were found to undergo stoichiometric cross‐coupling with phenylboronic acid to yield sulfides. While ethyl trifluoroacetate was also found to form an η²‐carbonyl complex, phenyl esters were found to predominantly undergo C_aryl?O bond cleavage to yield arylnickel complexes. These could also undergo transmetalation to yield biaryls. Attempts to render the reactions catalytic were hindered by ligand scrambling to yield nickel bis(acetate) complexes, the formation of which was supported by independent syntheses. Finally, 2‐naphthyl acetate was also found to undergo clean C_aryl?O bond cleavage, and although stoichiometric cross‐coupling with phenylboronic acid proceeded with good yield, catalytic turnover has so far proven elusive.     

Structure–activity relationship of N‐heterocyclic carbene–Pd(II)–imidazole complexes in Suzuki–Miyaura coupling between 4‐methoxyphenyl chloride and phenylboronic acid

A series of N‐heterocyclic carbene–PdCl₂–imidazole [NHC–Pd(II)–Im] complexes were synthesized and the structure of most of them was unambiguously determined by X‐ray single‐crystal diffraction. The structure–activity relationship of these complexes was investigated for the Suzuki–Miyaura coupling between 4‐methoxyphenyl chloride and phenylboronic acid, and the effect of the NHCs and Im moieties were fully discussed. The sterically hindered IPr‐based complex showed the highest catalytic activity. Copyright © 2013 John Wiley & Sons, Ltd.     

Room‐temperature Suzuki–Miyaura cross‐coupling reaction with α‐diimine Pd(II) catalysts

An α‐diimine Pd(II) complex containing chiral sec‐phenethyl groups, {bis[N,N′‐(4‐methyl‐2‐sec‐phenethylphenyl)imino]‐2,3‐butadiene}dichloropalladium (rac‐ C1 ), was synthesized and characterized. rac‐ C1 was applied as an efficient catalyst for the Suzuki–Miyaura cross‐coupling reaction between various aniline halides and arylboronic acid in PEG‐400–H₂O at room temperature. Among a series of aniline halides, rac‐ C1 did not catalyze the cross‐coupling of aniline chlorides and fluorides but efficiently catalyzed the cross‐coupling of aniline bromides and iodides with phenylboronic acid. The catalytic activity reduced slightly with increasing steric hindrance of the aniline bromides. The complexes {bis[N,N′‐(4‐fluoro‐2,6‐diphenylphenyl)imino]‐2,3‐butadiene}dichloropalladium and {bis[N,N′‐(4‐fluoro‐2,6‐diphenylphenyl)imino]acenaphthene}dichloropalladium were also found to be efficient catalysts for the reaction. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis of polymers possessing tetraphenylethylene units by three‐component coupling reactions of poly(p‐phenylene ethynylene) derivative with aryl halides and phenylboronic acid

A derivative of poly(p‐phenylene ethynylene) was subjected to the palladium‐catalyzed three‐component coupling reactions with aryl halides and phenylboronic acid to obtain polymers having tetrasubstituted cis‐vinylene units. For example, 69% of the acetylene units in the prepolymer were converted to cis‐vinylene (i.e., tetrasubstituted cis‐vinylene) units using iodobenzene and phenylboronic acid (5 equiv each with respect to acetylene units). In the UV–vis absorption spectra of the resulting polymers, clear hypsochromic shifts of the absorption maxima were observed, while bathochromic shifts and suppression of the efficiency were observed in their photoluminescence spectra. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 787–791     

N‐methyliminodiacetic acid as a simple and highly efficient ligand for palladium‐catalyzed Suzuki–Miyaura cross‐coupling of aryl chlorides

A simple, air‐stable, inexpensive and easily prepared molecule, N‐methyliminodiacetic acid (MIDA), is reported as a ligand for palladium‐catalyzed Suzuki–Miyaura cross‐coupling reaction of phenylboronic acid with aryl chlorides. The yield of the corresponding Suzuki coupling reaction is up to around 90% at both high temperature of 80°C and room temperature under ambient atmosphere. Copyright © 2015 John Wiley & Sons, Ltd.     

Cross‐coupling reactions in water using ionic liquid‐based palladium(II)–phosphinite complexes as outstanding catalysts

Two new phosphinite ligands based on ionic liquids [(Ph₂PO)C₇H₁₄N₂Cl]Cl ( 1 ) and [(Cy₂PO)C₇H₁₄N₂Cl]Cl ( 2 ) were synthesized by reaction of 1‐(3‐chloro‐2‐hydoxypropyl)‐3‐methylimidazolium chloride, [C₇H₁₅N₂OCl]Cl, with one equivalent of chlorodiphenylphosphine or chlorodicyclohexylphosphine, respectively, in anhydrous CH₂Cl₂ and under argon atmosphere. The reactions of 1 and 2 with MCl₂(cod) (M = Pd, Pt; cod = 1,5‐cyclooctadiene) yield complexes cis‐[M([(Ph₂PO)C₇H₁₄N₂Cl]Cl)₂Cl₂] and cis‐[M(Cy₂PO)C₇H₁₄N₂Cl]Cl)₂Cl₂], respectively. All complexes were isolated as analytically pure substances and characterized using multi‐nuclear NMR and infrared spectroscopies and elemental analysis. The catalytic activity of palladium complexes based on ionic liquid phosphinite ligands 1 and 2 was investigated in Suzuki cross‐coupling. They show outstanding catalytic activity in coupling of a series of aryl bromides or aryl iodides with phenylboronic acid under the optimized reaction conditions in water. The complexes provide turnover frequencies of 57 600 and 232 800 h^?1 in Suzuki coupling reactions of phenylboronic acid with p‐bromoacetophenone or p‐iodoacetophenone, respectively, which are the highest values ever reported among similar complexes for Suzuki coupling reactions in water as sole solvent in homogeneous catalysis. Furthermore, the palladium complexes were also found to be highly active catalysts in the Heck reaction affording trans‐stilbenes. Copyright © 2014 John Wiley & Sons, Ltd.     

Pd‐SBT@MCM‐41: As an efficient,stable and recyclable organometallic catalyst for C‐C coupling reactions and synthesis of 5‐substituted tetrazoles

A palladium S‐benzylisothiourea complex was anchored on functionalized MCM‐41 (Pd‐SBT@MCM‐41) and applied as efficient and reusable catalyst for the synthesis of 5‐substituted 1H –tetrazoles using [2 + 3] cycloaddition reaction of various organic nitriles with sodium azide (NaN₃) in poly(ethylene glycol) (PEG) as green solvent. Also this catalyst was applied as an versatile organometallic catalyst for Suzuki cross‐coupling reaction of aryl halides and phenylboronic acid (PhB(OH)₂) or sodium tetraphenyl borate (NaB(Ph)₄). This nanocatalyst was characterized by thermal gravimetric analysis (TGA), X‐ray Diffraction (XRD), scanning electron microscopy (SEM), inductively Coupled Plasma (ICP) and N₂ adsorption–desorption isotherms techniques. Recovery of the catalyst is easily achieved by centrifugation for several consecutive runs.