Catalytic Properties of Nanoscale Iron‐Doped Zirconia Solid‐Solution Aerogels

Nanoscale iron‐doped zirconia solid‐solution aerogels are prepared via a simple ethanol thermal route using zirconyl nitrate and iron nitrate as starting materials, followed by a supercritical fluid drying process. Structural characteristics are investigated by means of powder X‐ray diffraction (XRD), thermal analyses (TG/DTA), N₂ adsorption measurements and diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS). The results show that the resulting iron‐doped solid solutions are metastable tetragonal zirconia which exhibit excellent dispersibility and high solubility of iron oxide. Further, when the Fe:(Fe+Zr) ratio x is lower than 0.10, all of the Fe³⁺ ions can be incorporated into ZrO₂ by substituting Zr⁴⁺ to form Zr_1?xFe_xO_y solid solutions. Moreover, for the first time, an additional hydroxyl group band that is not present in pure ZrO₂ is observed by DRIFTS for the Zr(Fe)O₂ solid solution. This is direct evidence of Fe³⁺ ions incorporated into ZrO₂. These Zr_1?xFe_xO_y solid solutions are excellent catalysts for the solvent‐free aerobic oxidation of n‐hexadecane using air as the oxidant under ambient conditions. The Zr_0.8Fe_0.2O_y solid‐solution catalyst demonstrates the best catalytic properties, with the conversion of n‐hexadecane reaching 36.2 % with 48 % selectivity for ketones and 24 % selectivity for alcohols and it can be recycled five times without significant loss of activity.     

Preparation and Characterization of Mg‐Zr Mixed Oxide Aerogels and Their Application as Aldol Condensation Catalysts

A series of Mg‐Zr mixed oxides with different nominal Mg/ (Mg+Zr) atomic ratios, namely 0, 0.1, 0.2, 0.4, 0.85, and 1, is prepared by alcogel methodology and fundamental insights into the phases obtained and resulting active sites are studied. Characterization is performed by X‐ray diffraction, transmission electron microscopy, X‐ray photoelectron spectroscopy, N₂ adsorption–desorption isotherms, and thermal and chemical analysis. Cubic Mg_xZr_1?xO_2?x solid solution, which results from the dissolution of Mg²⁺ cations within the cubic ZrO₂ structure, is the main phase detected for the solids with theoretical Mg/ (Mg+Zr) atomic ratio ≤0.4. In contrast, the cubic periclase (c‐MgO) phase derived from hydroxynitrates or hydroxy precursors predominates in the solid with Mg/(Mg+Zr)=0.85. c‐MgO is also incipiently detected in samples with Mg/(Mg+Zr)=0.2 and 0.4, but in these solids the c‐MgO phase mostly arises from the segregation of Mg atoms out of the alcogel‐derived c‐Mg_xZr_1?xO_2?x phase during the calcination process, and therefore the species c‐MgO and c‐Mg_xZr_1?xO_2?x are in close contact. Regarding the intrinsic activity in furfural–acetone aldol condensation in the aqueous phase, these Mg? O? Zr sites located at the interface between c‐Mg_xZr_1?xO_2?x and segregated c‐MgO display a much larger intrinsic activity than the other noninterface sites that are present in these catalysts: Mg? O? Mg sites on c‐MgO and Mg? O? Zr sites on c‐Mg_xZr_1?xO_2?x. The very active Mg? O? Zr sites rapidly deactivate in the furfural–acetone condensation due to the leaching of active phases, deposition of heavy hydrocarbonaceous compounds, and hydration of the c‐MgO phase. Nonetheless, these Mg‐Zr materials with very high specific surface areas would be suitable solid catalysts for other relevant reactions catalyzed by strong basic sites in nonaqueous environments.     

Visualization of Heterogeneous Oxygen Storage Behavior in Platinum‐Supported Cerium‐Zirconium Oxide Three‐Way Catalyst Particles by Hard X‐ray Spectro‐Ptychography

The cerium density and valence in micrometer‐size platinum‐supported cerium–zirconium oxide Pt/Ce₂Zr₂O_x (x=7–8) three‐way catalyst particles were successfully mapped by hard X‐ray spectro‐ptychography (ptychographic‐X‐ray absorption fine structure, XAFS). The analysis of correlation between the Ce density and valence in ptychographic‐XAFS images suggested the existence of several oxidation behaviors in the oxygen storage process in the Ce₂Zr₂O_x particles. Ptychographic‐XAFS will open up the nanoscale chemical imaging and structural analysis of heterogeneous catalysts.     

Sol-gel Synthesis and Electrochemical Performance of Li4-xMgxTi5-xZrxO12 Anode Material for Lithium-ion Batteries

The anode materials Li_4?xMg_xTi_5?xZr_xO₁₂ (x=0, 0.05, 0.1) were successfully synthesized by sol‐gel method using Ti(OC₄H₉)₄, CH₃COOLi·2H₂O, MgCl₂·6H₂O and Zr(NO₃)₃·6H₂O as raw materials. The crystalline structure, morphology and electrochemical properties of the as‐prepared materials were characterized by XRD, SEM, cyclic voltammograms (CV), electrochemical impedance spectroscopy (EIS) and charge‐discharge cycling tests. The results show that the lattice parameters of the Mg‐Zr doped samples are slightly larger than that of the pure Li₄Ti₅O₁₂, and Mg‐Zr doping does not change the basic Li₄Ti₅O₁₂ structure. The rate capability of Li_4?xMg_xTi_5?xZr_xO₁₂ (x=0.05, 0.1) electrodes is significantly improved due to the expansile Li⁺ diffusion channel and reduced charge transfer resistance. In this study, Li_3.95Mg_0.05Ti_4.95Zr_0.05O₁₂ represented a relatively good rate capability and cycling stability, after 400 cycles at 10 C, the discharge capacity retained as 134.74 mAh·g^?1 with capacity retention close to 100%. The excellent rate capability and good cycling performance make Li_3.95Mg_0.05Ti_4.95Zr_0.05O₁₂ a promising anode material in lithium‐ion batteries.     

Bulk and surface analysis of Ti1–xFexO2/Fe2O3 composites prepared by solid state reaction for photocatalytic applications

Ti_1–xFe_xO₂ / Fe₂O₃ (x = 0.3, 0.6, and 0.7 wt%) composites were prepared by solid state reaction of the oxides TiO₂ (rutile phase) and Fe₂O₃ at 550 °C. The following techniques were applied for the characterization of the composites: X‐ray powder diffraction, Mössbauer spectroscopy, SEM, energy dispersive X‐ray spectroscopy and adsorption of nitrogen. The anatase/rutile/hematite ratio and the abundance of Fe³⁺ were quantified. The results indicate that Fe³⁺ substituted Ti⁴⁺ in the rutile structure and that the α‐Fe₂O₃ phase was predominantly on the surface of the crystalline Ti_1–xFe_xO₂ powders. A substantial increase of the materials density, with respect to rutile, favoured the application of the composites in photocatalytic experiments. The performance of the solids upon the photodegradation of aqueous solutions of carbofuran was evaluated. The Lewis sites created in the composites correlated directly with the photodegradation rate constant of carbofuran and the decrease of the total organic carbon content in the treated solutions. Copyright © 2011 John Wiley & Sons, Ltd.     

General and facile synthesis of ceria-based solid solution nanocrystals and their catalytic properties

Uniform Ce_1−xZr_xO₂ (x=0.2–0.8) nanocrystals with ultra-small size were synthesized through a thermolysis process, facilitated by the initial formation of precursor (hydrated (Ce,Zr)-hydroxides) at low temperature. TEM, XRD, EDAX, and Raman spectra were employed to study the formation of the solid solutions with various Ce/Zr ratios. Ultraviolet–visible (UV–vis) spectra showed that the ratios of Ce³⁺ to Ce⁴⁺ in both surface and bulk for the as-prepared Ce_1−xZr_xO₂ nanocrystals increased with the zirconium content x. The well-distributed Zr and Ce in the hydrated (Ce,Zr)-hydroxides before their thermolysis became the crucial factor for the structural homogeneity of the products. In addition, this strategy was extended to the synthesis of Ce_1−xGd_xO_1−x/2, Ce_1−xSm_xO_1−x/2, and Ce_1−xSn_xO₂ solid solutions. Catalytic measurements indicated that the ceria-based catalysts were active for CO oxidation at temperatures beyond 250 °C and the sequence of catalytic activity was Ce_0.5Zr_0.5O₂>Ce_0.8Zr_0.2O₂>Ce_0.2Zr_0.8O₂>Ce_0.5Sm_0.5O_1.75.     

Visualization of the Heterogeneity of Cerium Oxidation States in Single Pt/Ce2Zr2Ox Catalyst Particles by Nano‐XAFS

The cerium oxidation states in single catalyst particles of Pt/Ce₂Zr₂O_x (x=7 to 8) were investigated by spatially resolved nano X‐ray absorption fine structure (nano‐XAFS) using an X‐ray nanobeam. Differences in the distribution of the Ce oxidation states between Pt/Ce₂Zr₂O_x single particles of different oxygen compositions x were visualized in the obtained two‐dimensional X‐ray fluorescent (XRF) mapping images and the Ce L_III‐edge nano X‐ray absorption near‐edge structure (nano‐XANES) spectra.     

Synthesis,optical properties,and photocatalytic activity of lanthanide-doped anatase

Quasi-one-dimensional (1D) Ti_{1 ? x} Ln _x O_{2 ? x/2} anatase solid solutions were prepared by heating Ti_{1 ? x} Ln _x (OCH₂CH₂O)_{2 ? x/2} precursors, where Ln = Nd, Eu, Tb, Er (x = 0.025), or Sm (0.005 ≤ x ≤ 0.025), in air. These solid solution were found to have a photocatalytic activity in hydroquinone oxidation in aqueous solution under exposure to UV radiation. UV-Vis absorption spectra were recorded for Ti_{1 ? x} Ln _x O_{2 ? x/2} (Nd, Sm, Eu, Tb, or Er). The electronic structure and optical absorption spectra were calculated for anatase doped with neodymium, samarium, or terbium.     

Highly Dispersed Ce x Zr1−x O2 Nano-Oxides Over Alumina, Silica and Titania Supports for Catalytic Applications

We have been exploring the utilization of supported ceria and ceria–zirconia nano-oxides for different catalytic applications. In this comprehensive investigation, a series of Ce _x Zr_1−x O₂/Al₂O₃, Ce _x Zr_1−x O₂/SiO₂ and Ce _x Zr_1−x O₂/TiO₂ composite oxide catalysts were synthesized and subjected to thermal treatments from 773 to 1073 K to examine the influence of support on thermal stability, textural properties and catalytic activity of the ceria–zirconia solid solutions. The physicochemical characterization studies were performed using X-ray diffraction (XRD), Raman spectroscopy (RS), X-ray photoelectron spectroscopy (XPS), and high-resolution transmission electron microscopy (HREM), thermogravimetry and BET surface area methods. To evaluate the catalytic properties, oxygen storage/release capacity (OSC) and CO oxidation activity measurements were carried out. The XRD analyses revealed the formation of Ce_0.75Zr_0.25O₂, Ce_0.6Zr_0.4O₂, Ce_0.16Zr_0.84O₂ and Ce_0.5Zr_0.5O₂ phases depending on the nature of support and calcination temperature employed. Raman spectroscopy measurements in corroboration with XRD results suggested enrichment of zirconium in the Ce _x Zr_1−x O₂ solid solutions with increasing calcination temperature thereby resulting in the formation of oxygen vacancies, lattice defects and oxygen ion displacement from the ideal cubic lattice positions. The HREM results indicated a well-dispersed cubic Ce _x Zr_1−x O₂ phase of the size around 5 nm over all supports at 773 K and there was no appreciable increase in the size after treatment at 1073 K. The XPS studies revealed the presence of cerium in both Ce⁴⁺ and Ce³⁺ oxidation states in different proportions depending on the nature of support and the treatment temperature applied. All characterization techniques indicated absence of pure ZrO₂ and crystalline inactive phases between Ce–Al, Ce–Si and Ce–Ti oxides. Among the three supports employed, silica was found to stabilize more effectively the nanosized Ce _x Zr_1−x O₂ oxides by retarding the sintering phenomenon during high temperature treatments, followed by alumina and titania. Interestingly, the alumina supported samples exhibited highest OSC and CO oxidation activity followed by titania and silica. Details of these findings are consolidated in this review.     

Chemical solution processing and characterization of Ba(Zr,Ti)O<Subscript>3</Subscript>/LaNiO<Subscript>3</Subscript> layered thin films

Ba(Zr,Ti)O₃/LaNiO₃ layered thin films have been synthesized by chemical solution deposition (CSD) using metal-organic precursor solutions. Ba(Zr,Ti)O₃ thin films with smooth surface morphology and excellent dielectric properties were prepared on Pt/TiO _x /SiO₂/Si substrates by controlling the Zr/Ti ratios in Ba(Zr,Ti)O₃. Chemically derived LaNiO₃ thin films crystallized into the perovskite single phase and their conductivity was sufficiently high as a thin-film electrode. Ba(Zr,Ti)O₃/LaNiO₃ layered thin films of single phase perovskite were fabricated on SiO₂/Si and fused silica substrates. The dielectric constant of a Ba(Zr_0.2Ti_0.8)O₃ thin film prepared at 700°C on a LaNiO₃/fused silica substrate was found to be approximately 830 with a dielectric loss of 5% at 1 kHz and room temperature. Although the Ba(Zr_0.2Ti_0.8)O₃ thin film on the LaNiO₃/fused silica substrate showed a smaller dielectric constant than the Ba(Zr_0.2Ti_0.8)O₃ thin film on Pt/TiO _x /SiO₂/Si, small temperature dependence of dielectric constant was achieved over a wide temperature range. Furthermore, the fabrication of the Ba(Zr,Ti)O₃/LaNiO₃ films in alternate thin layers similar to a multilayer capacitor structure was performed by the same solution deposition process.     

Imaging of Oxygen Diffusion in Individual Platinum/Ce2Zr2Ox Catalyst Particles During Oxygen Storage and Release

The spatial distribution of Ce³⁺ and Ce⁴⁺ in each particle of Ce₂Zr₂O_x in a three‐way conversion catalyst system was successfully imaged during an oxygen storage/release cycle by scanning X‐ray absorption fine structure (XAFS) using hard X‐ray nanobeams. For the first time, nano‐XAFS imaging visualized and identified the modes of non‐uniform oxygen diffusion from the interface of Pt catalyst and Ce₂Zr₂O_x support and the active parts in individual catalyst particles.     

Amino acid ionic liquid‐based titanomagnetite nanoparticles: An efficient and green nanocatalyst for the synthesis of 1,4‐dihydropyrano[2,3‐c]pyrazoles

The amino acid ionic liquid tetrabutylammonium asparaginate (TBAAsp) was immobilized on titanomagnetite (Fe_3?xTi_xO₄) nanoparticles in a facile one‐pot process using an organosilane compound (TMSP) as spacer. The modified Fe_3?xTi_xO₄@TMSP@TBAAsp magnetic nanoparticles were characterized using Fourier transform spectroscopy, scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, vibrating sample magnetometry and thermogravimetric analysis. The resulting analytical data clearly verified the successful immobilization of the ionic liquid on the magnetic substrate. The magnetic ionic liquid‐based nanoparticles exhibited high catalytic activity in the synthesis of 1,4‐dihydropyrano[2,3‐c]pyrazole derivatives via a one‐pot three‐component reaction under mild reaction conditions. The catalyst was easily recycled and reused for at least six runs without any considerable loss of activity.     

Stability of the anatase phase in nanodimensional titanium dioxide doped with europium(III), samarium(III), and iron(III)

lid solutions Ti_1−x M _x O_2−x/2 in the anatase and rutile forms were obtained from the precursors Ti_1−x M _x (OCH₂CH₂O)_2−x/2 at T = 450–900 °C. The temperature and concentration dependence of the phase transformation of anatase to rutile in Ti_1−x M _x O_2−x/2 was investigated by Raman spectroscopy. It was shown that the anatase phase is stabilized most effectively by the Eu³⁺ dopant.     

Glycolate Ti1 − x Fe x (OCH2CH2O)2 − x/2 as a precursor for the preparation of quasi-one-dimensional (1D) solid solutions Ti1 − x Fe x O2 − 2x/2 (0 ≤ x ≤ 0.1)

Quasi-one-dimensional (1D) solid solutions Ti_{1 ? x} Fe _x (OCH₂CH₂O)_{2 ? x/2} (0 < x ≤ 0.1) with the structure of anatase were prepared by heating the glycolate Ti_{1 ? x} Fe _x (OCH₂CH₂O)_{2 ? x/2} in an atmosphere of air at a temperature of >450°C. The conditions of formation and the properties of the new glycolate Ti₃Fe₂(OCH₂CH₂O)₉ were described. It was found that the synthesized Ti_{1 ? x} Fe _x O_{2 ? 2x/2} solid solutions exhibit photocatalytic activity in the reaction of hydroquinone oxidation in an aqueous solution on irradiation with UV light. A correlation between the rate of oxidation of hydroquinone and the concentration of iron in the catalyst was established. A procedure for the preparation of titanium dioxide with the structure of anatase doped with iron and carbon (Ti_{1 ? x} Fe _x O_{(2 ? x/2) ? yCy)} and also composites on its basis, which contain an excess amount of carbon, was proposed.     

Synthesis of W‐doped TiO2 by low‐temperature hydrolysis: Effects of annealing temperature and doping content on the surface microstructure and photocatalytic activity

A series of tungsten‐doped Titania photocatalysts were synthesized using a low‐temperature method. The effects of dopant concentration and annealing temperature on the phase transitions, crystallinity, electronic, optical, and photocatalytic properties of the resulting material were studied. The X‐ray patterns revealed that the doping delays the transition of anatase to rutile to a high temperature. A new phase W_yTi_1‐yO₂ appeared for 5.00 wt% W‐TiO₂ annealed at 900 °C. Raman and diffuse reflectance UV–Vis spectroscopy showed that band gap values decreased slightly up to 700 °C. X‐ray photoelectron spectroscopy showed that surface species viz. Ti³⁺, Ti⁴⁺, O^2?, oxygen‐vacancies, and adsorbed OH groups vary depending on the preparation conditions. The photocatalytic activity was evaluated via the degradation of methylene blue using LED white light. The degradation rate was affected by the percentage of dopants. The best photocatalytic activity was achieved with the sample labeled 5.00 wt% W‐TiO₂ annealed at 700 °C.     

Synthesis of ceria–zirconia mixed oxide from cerium and zirconium glycolates via sol–gel process and its reduction property

Ceria–zirconia mixed oxide was successfully synthesized via the sol–gel process at ambient temperature, followed by calcination at 500, 700 and 900 °C. The synthesis parameters, such as alkoxide concentration, aging time and heating temperature, were studied to obtain the most uniform and remarkably high‐surface‐area cubic‐phase mixed oxides. The thermal stability of both oxides was enhanced by mutual substitution. Surface areas of the Ce_xZr_1?xO₂ powders were improved by increasing ceria content, and their thermal stability was increased by the incorporation of ZrO₂. The most stable cubic‐phase solid solutions were obtained in the Ce range above 50 mol%. The highest surface area was obtained from the mixed catalyst containing a ceria content of 90 mol% (200 m²/g). Temperature programmed reduction results show that increasing the amount of Zr in the mixed oxides results in a decrease in the reduction temperature, and that the splitting of the support reduction process into two peaks depends on CeO₂ content. The CO oxidation activity of samples was found to be related to its composition. The activity of catalysts for this reaction decreased with a decrease in Zr amount in cubic phase catalysts. Ce₆Zr₄O₂ exhibited the highest activity for CO oxidation. Copyright © 2006 John Wiley & Sons, Ltd.     

Low temperature carbon monoxide catalytic oxidation at the Pd/Ce–Zr–Al–Ox catalyst

The homogeneous chemical composition ceria–zirconia–alumina (Ce–Zr–Al–O_x) nano-alloy were successfully synthesized by surfactant-assisted parallel flow co-precipitation method and applied as supports for low temperature CO oxidation. The experiment conditions were studied in detailed. At 0.92 wt% Pd loading, 30,000 ppm CO could be completely oxidized to CO₂ at 30 °C at a WHSV of 4,380 ml g^?1 h^?1 over the Pd/Ce–Zr–Al–O_x (n_Ce:n_Zr = 3:1) catalyst. Pd/Ce–Zr–Al–O_x catalysts were systematical studied by mean of BET, XRD and TEM analysis. XRD characterization showed that zirconium element entered into cubic structure of ceria and leaded to structure distortion. Addition of aluminum increased specific surface area of ceria–zirconia solid solution substantially. The average pore diameter of Ce–Zr–Al–O_x support palladium catalysts were the key impact factor for CO oxidation. When the Pd/Ce–Zr–Al–O_x catalysts had highly dispersed palladium nanoparticles, large average pore diameter, suitable surface area and pore volume, the activity of CO oxidation was the best.     

Solid‐Solution Alloy Nanoparticles of the Immiscible Iridium–Copper System with a Wide Composition Range for Enhanced Electrocatalytic Applications

For the first time, we synthesize solid‐solution alloy nanoparticles of Ir and Cu with a size of ca. 2 nm, despite Ir and Cu being immiscible in the bulk up to their melting over the whole composition range. We performed a systematic characterization on the nature of the Ir_xCu_1?x solid‐solution alloys using powder X‐ray diffraction, scanning transmission electron microscopy coupled with energy‐dispersive X‐ray spectroscopy and X‐ray photoelectron spectroscopy. The results showed that the Ir_xCu_1?x alloys had a face‐centered‐cubic structure; charge transfer from Cu to Ir occurred in the alloy nanoparticles, as the core‐level Ir 4f peaks shifted to lower energy region with the increase in Cu content. Furthermore, we observed that the alloying of Ir with Cu enhanced both the electrocatalytic oxygen evolution and oxygen reduction reactions. The enhanced activities could be attributed to the electronic interaction between Ir and Cu arising from the alloying effect at atomic‐level.     

Synthesis and optical absorption property of the Zn2TixSn1−xO4 (0?x?1) solid solutions

Zn₂Ti_xSn_1−xO₄ (0?x?1) solid solutions with an inverse spinel structure (Fd3m) were synthesized by solid-state reactions at 1300°C of the stoichiometric mixtures of ZnO, TiO₂ and SnO₂. X-ray diffraction, thermogravimetric and differential thermal analyses, scanning electron microscopy, transmission electron microscopy and BET specific surface area measurements were used to gain insights into the solid-state reactions and phase transformation of the system. Optical absorption property of the Zn₂Ti_xSn_1−xO₄ (0?x?1) solid solutions was studied with the ultraviolet-visible diffuse reflectance spectroscopy (UV-Vis DRS). The Zn₂Ti_xSn_1−xO₄ (0?x?1) solid solutions showed optical absorptions of the semiconductors in the near ultraviolet region; the adsorption band shifts with the composition of the solid solution.     

Effects of Ti and Zr Substituted on the Electrochemical Characteristics of MgNi-Based Alloy Electrodes

Mg-based hydrogen storage alloys MgNi, Mg0.9Ti0.1Ni, and Mg0.9Ti0.06Zr0.04Ni were successfully prepared by means of mechanical alloying （MA）. The structure and the electrochemical characteristics of these Mg-based materials were studied. The X-ray diffraction （XRD） result shows that the main phases of the alloys exhibit amorphous structure. The scanning electron microscopy （SEM） photograph shows that the particle size of Ti and Zr substituted alloys was about 2-4 μm in diameter. The cycle lives of the alloys were prolonged by adding Ti and Zr. After 50 charge-discharge cycles, the discharge capacity of Mg0.9Ti0.06Zr0.04Ni was 91.74% higher than that of MgNi alloy and 37.96% higher than that of Mg0.9Ti0.1Ni alloy. The main reason for the electrode capacity decay is the formation of Mg（OH）2 （product of Mg corrosion） at the surface of alloy. The potentiodynamic polarization result indicates that Ti and Zr doping improves the anticorrosion in an alkaline solution. The electrochemical impedance spectroscopy （EIS） results suggest that proper amount of Ti and Zr doping improves the electrochemical catalytic activity significantly.