Comparison of Needle Concentrator with SPME for GC Determination of Benzene, Toluene, Ethylbenzene, and Xylenes in Aqueous Samples

A method of solventless extraction of volatile organic compounds from aqueous samples has been developed and validated. A new arrangement in which the internal volume of a needle capillary adsorption trap is completely filled with Porapak Q, as adsorbent material, and wet alumina, as a source of desorptive water vapor flow, is presented. The device has been used for head-space sampling of benzene, toluene, ethylbenzene, and xylenes (BTEX) from water samples and compared with solid-phase microextraction. Under the same sampling conditions the analytical characteristics of the device for the BTEX compounds are better than those of solid-phase microextraction. Limits of detection and quantification are below 0.5 μ g L⁻¹.     

Electrospun polymer nanofibers as a solid-phase extraction sorbent for the determination of trace pollutants in environmental water

This paper describes the novel preparation of three kinds of nanofibers [poly(styrene-co-methacrylic acid), poly(styrene-co-p-styrene sulfonate), polystyrene] investigated as solid-phase extraction (SPE) sorbents to extract six compounds (nitrobenzene, 2-naphthol, benzene, n-butyl p-hydroxybenzoate, naphthalene, p-dichlorobenzene) in environmental water by high-performance liquid chromatography. Parameters affecting extraction efficiency were investigated in detail to explore the extraction mechanism of the nanofibers. Under optimized conditions, six compounds followed an excellent linear relationship in the range 10–5,000 ng mL⁻¹ with coefficients of determination (r ²) greater than 0.99. The repeatability (expressed as relative standard deviations) was from 3.0 to 7.0%, corresponding to 2.0 mL of water samples at 25 and 500 ng mL⁻¹ spiked levels for the six compounds. The limits of detection varied from 0.01 to 0.15 ng mL⁻¹ (signal-to-noise ratio of3). A comparison of the SPE using nanofibers as sorbents and the most commonly used octadecylsilica SPE cartridges was carried out in terms of absolute recovery, sensitivity, and reproducibility for the compounds investigated. Finally, the method was applied to four real water samples. The results highlighted the importance of functional groups, and the polarity of nanofibers in controlling sorption of target compounds, and clearly showed that the new method could be a viable and environmentally friendly technique for analyzing pollutants in environmental samples.     

Bamboo Charcoal as Solid-Phase Extraction Adsorbent for the Determination of Organophosphorus Pesticides in Water Samples by High-Performance Liquid Chromatography

In this paper, bamboo charcoal was successfully developed for the solid-phase extraction adsorbent for the determination of six organophosphorus pesticides in water samples. After the bamboo charcoal was pretreated and packed in the solid-phase extraction cartridge, the organophosphorus pesticides in water samples were carried out the solid-phase extraction. To establish a perfect solid-phase extraction procedure, the experimental conditions including the eluent, eluent volume, pH of the sample, flow rate of the sample, and loading volume of the sample were all investigated. When 100 mL water samples in the pH range of 6–7 were loaded with the flow rate of 2.5 mL · min^?1 and then eluted with 10 mL acetonitrile, the proposed extraction method was validated by the recovery, correlation coefficient (R²), repeatability (RSD, n = 7) and LODs, which were 69.6–93.4%, 0.9982–0.9998, 2.9–5.6%, and 0.08–1.04 µg · L^?1, respectively. Furthermore, the analysis of the tap, snow, and river water samples demonstrated the feasibility of the proposed SPE method for real water samples. Based on the aforementioned factors, it could be concluded that bamboo charcoal was a good solid-phase extraction adsorbent, and this proposed solid-phase extraction method was suitable for the effective enrichment and determination of the organophosphorus pesticides in water samples.     

Chemically modified resins for solid-phase extraction

The packings most widely used for solid-phase extraction are hydrophobic and make poor surface contact with aqueous samples unless the resins are first treated with an activating organic solvent such as methanol. Insertion of an acetyl- or hydroxymethyl group into a porous polystyrene-divinylbenzene resin provides a more hydrophilic surface that is easily wetted by water alone. Small columns of the chemically modified resins were found to be very efficient for the solid-phase extraction of many types of organic solutes from aqueous samples. Comparative recovery studies showed that the modified resins are superior to both silica packings and unmodified organic resins for the solid-phase extraction of organic compounds, and especially for polar organics such as phenols.     

Ability of a salivary intrinsically unstructured protein to bind different tannin targets revealed by mass spectrometry

Superporous monolithic hydrogels (cryogel monoliths) are elastic, sponge-like materials that can be prepared in an aqueous medium through a cryotropic gelation technique. These monoliths show interesting properties for the development of high-throughput solid-phase extraction supports to treat large volumes of aqueous samples. In this work, a cryogel-supported molecularly imprinted solid-phase extraction approach for the endocrine disruptor bisphenol A (BPA) from river water and wine samples is presented. An imprinted polymer with molecular recognition properties for BPA was prepared in acetonitrile by thermal polymerization of a mixture of 4,4′-dihydroxy-2,2-diphenyl-1,1,1,3,3,3-trifluoropropane as a mimic template of BPA, 4-vinylpyridine and trimethylolpropane trimethacrylate in a molar ratio of 1 + 6 + 6. Fine imprinted particles (<10 μm) were embedded in a poly-acrylamide-co-N,N′-methylenbisacrylamide cryogel obtained by ammonium persulfate-induced cryopolymerization at −18 °C. The resulting monolithic gel was evaluated for its use as a sorbent support in an off-line solid-phase extraction approach to recover BPA from dilute aqueous samples with minimum pre-loading work-up. The optimized extraction protocol resulted in a reliable MISPE method suitable to selectively extract and preconcentrate BPA from river water and red wine samples, demonstrating the practical feasibility of cryogel-trapped imprinted polymers as solid-phase extraction materials     

Gas Chromatographic Method for Routine Determination of Oleanolic and Ursolic Acids in Medicinal Plants

Summary A rapid and simple gas chromatographic method has been established for routine analysis of free oleanolic and ursolic acids in dried samples of medicinal herbs. Soxhlet extraction of triterpenes was followed by solid-phase extraction (SPE). Amounts of the compounds were measured by gas chromatography after silylation of the purified samples. Experiments were performed to establish the optimum conditions (e.g. solvent, and mode and duration of extraction) for calibration curve linearity, sensitivity, reproducibility, and recovery. The conditions used for derivatization and gas chromatographic analysis resulted in an improvement on literature data. The method devised enables accurate routine measurement of many samples in quite a short time (e.g. for chemotaxonomical screening, or quality control of herbal drugs). The practical application of the method was illustrated on five Lamiaceae species.     

A new approach based on a combination of direct and headspace cold-fiber solid-phase microextraction modes in the same procedure for the determination of polycyclic aromatic hydrocarbons and phthalate esters in soil samples

This study describes a new approach to cold-fiber solid-phase microextraction (CF-SPME) based on a combination of different extraction modes in the same extraction procedure. Also, the high quantity of water required to facilitate both the desorption of analytes from the matrix and their transport to the fiber coating is reported. The extraction mode was changed from the direct to the headspace mode in a single extraction while manipulating the extraction times and coating temperature to improve the extraction of compounds with different volatilities. Compounds with low volatility were better extracted in the direct mode, while the headspace mode was more appropriate for volatile compounds. Polycyclic aromatic hydrocarbons (PAHs) and phthalic acid esters (PEs) in sand or soil samples were used as model compounds and matrices in this study. The optimized conditions were: sample pH in the range of 4-7, addition of 12 mL of 194 g L(-1) aqueous NaCl solution in a 15 mL vial, and 80 min total extraction time with a sample temperature of 90°C (50 min in direct mode with coating at 90°C followed by 30 min in headspace mode with coating at 30°C). The proposed procedure was compared with conventional CF-SPME (with and without addition of water) and was found to be more effective for all the analytes, since it is capable of extracting both heavier and lighter compounds from soil samples in a single extraction procedure. The use of an excess of water and a combination of extraction modes in the same CF-SPME procedure are the main factors responsible for this enhancement. The proposed method was applied to the extraction of PAHs and PEs in spiked soil samples and excellent results were obtained for most of the compounds evaluated.     

Simultaneous determination of endocrine disrupting phenolic compounds and steroids in water by solid-phase extraction-gas chromatography-mass spectrometry

A solid-phase extraction (SPE)-gas chromatography (GC)-mass spectrometry (MS) analytical method for the simultaneous separation and determination of endocrine disrupting chemicals (EDCs) from water samples is described in detail. Important and contrasting EDCs including estrone, 17beta-estradiol, 17beta-ethynylestradiol, 16beta-hydroxyestrone, 4-nonylphenol, bisphenol A and 4-tert-octylphenol were selected as the target compounds. The SPE technique, followed by the derivatisation with bis (trimethylsilyl) trifluoroacetamide was used for the extraction recoveries of target compounds from water samples. A number of parameters that may affect the recovery of EDCs, such as the type of SPE cartridges, eluents, as well as water properties including pH value, and concentration of salts and humic substances were investigated. It is shown that the Oasis cartridges produced the best recoveries of target EDCs while ethyl acetate was efficient in eluting EDCs from SPE cartridges. The recovery of some EDCs was enhanced by the addition of salt, but reduced by the increase in pH value and humic acid concentration. The optimised method was further verified by performing spiking experiments in natural river water and seawater matrices, with good recovery and reproducibility for all the selected compounds. The established method was successfully applied to environmental water samples from East and West Sussex, UK, for the determination of the target EDCs.     

Rapid liquid chromatography-tandem mass spectrometry method for the determination of a broad mixture of pharmaceuticals in surface water

Herein, a new method for the detection of 13 different pharmaceuticals and one metabolite in surface water at low ng/L levels is described. The method utilizes ultra performance liquid chromatography-tandem mass spectrometry and a solid-phase extraction sample preparation. Mean method detection limits were low (4.10 ng/L) and overall solid-phase extraction recovery and reproducibility was adequate (mean recovery, 77.9%; mean RSD, 7.3%). The method allows for quick run times and minimal solvent use as compared with other previously reported high performance liquid chromatography-based methods. Application of this method for the detection of pharmaceuticals in Tennessee River surface water determined that caffeine, sulfamethoxazole, and carbamazepine were frequently detected (100% of samples). Trimethoprim was moderately detected (30% of samples); acetaminophen, atorvastatin, and lovastatin were infrequently detected (10% of samples); and ciprofloxacin, diltiazem, fluoxetine, levofloxacin, norfluoxetine, ranitidine, and sertraline were not detected. This study reports the first detection of lovastatin in surface water.     

Evaluation of Polyaniline as a Sorbent for SPE of a Variety of Polar Pesticides from Water Followed by CD-MEKC-DAD

A recently synthesized polyaniline (PANI) has been used and evaluated as a sorbent for solid-phase extraction of a variety of polar pesticides and some of their degradation products from water samples. Several classes of pesticides including phenoxy acids, triazines, ureas, oxime carbamates and carbamates were selected for this study. The determination of these pesticides was carried out using cyclodextrin modified micellar electrokinetic chromatography equipped with diode array detection. The recovery results using PANI were compared with those obtained by C₁₈, Isolute ENV+, Oasis HLB and LiChrolut EN. Effect of humic acid, as a major interference, on extraction recovery was also studied. The performance of the method was evaluated by analysis of tap and river water. The RSD of method was between 6 and 14% (n=3) and detection limits were in the range of 0.01–0.5 g L^–1 using 350-mL water samples.     

Novel Activated Carbon Fiber Solid-Phase Microextraction for Determination of Benzyl Chloride and Related Compounds in Water by Gas Chromatography–Mass Spectrometry

An activated carbon fiber (ACF) has been developed for use as an extraction fiber in solid-phase microextraction (SPME) and used to determine benzyl chloride, benzyl dichloride, and benzyl trichloride in water samples by headspace (HS) analysis. Experiments showed that ACF has excellent adsorption capacity. Its well-distributed surface makes desorption swift in a GC–MS injector. Several conditions affecting the ACF-SPME procedure, for example adsorption mode, adsorption time and temperature, and desorption time, were optimized. The optimized HS-ACF-SPME method has acceptable linearity, good precision, and reasonable RSD values for the compounds studied. The ACF is, therefore, a promising alternative for SPME.     

Determination of Butyltins in Sea Water by Gas Chromatography with Flame Photometric Detection

Use of a gas chromatograph with a flame-photometric detector (GC-FPD) is described to determine butyltin compounds in sea water. The butyltins in an acidified water sample (pH 3.0) are first complexed with tropolone, followed by solid-phase extraction (SPE) with a tropolone-treated C₁₈ cartridge. HCI at a small concentration is then added to the concentrated SPE eluate before GC analysis. This procedure is simple and off-column derivatization of analytes is not required. The organotins, viz. mono-, di- and tributyltin, are separated as their respective chlorides on a capillary column (HP-1) and are detected with a flame-photometric detector and an interference filter at 610 nm. Recoveries of the three butyltin species are quantitative (> 90%). Based on a sea water sample 200-mL, the detection limits for mono-, di- and tributyltin are 6,4 and 3 ng tin L^?1, respectively. This method is applied to analysis of trace butyltins in various samples of sea water.     

Large Volume Headspace Analysis Using Solid-Phase Microcolumn Extraction

A rapid and simple large volume headspace (HS) sampling technique termed headspace solid-phase microcolumn extraction (HS-SPMCE) is described. HS gas above a liquid or solid sample is aspirated by attaching a gas-tight syringe onto a glass thermal desorption tube filled with Tenax sorbent. The trapped analytes are recovered by thermal desorption for gas chromatography–mass spectrometry (GC–MS) analysis. Benzene, toluene, ethylbenzene and the xylene isomers (BTEX) are used as model compounds to demonstrate the application of the extraction procedure for water samples. The results of the tests of the effect of agitation time and aspiration rate on recovery of the analytes show a good robustness of the method. BTEX are determined in the linear range from 0.5 to 50.0 μg L^?1 with limits of detection (3 σ) ranging within 0.09–0.14 μg L^?1 (MS was in scan mode). The method provides a good repeatability (RSD < 9%) and only a negligible carryover effect was observed ( ≤0.05%) when analysing BTEX at concentration 50.0 μg L^?1.     

On-line coupling of solid-phase extraction and gas chromatography with atomic emission detection for analysis of trace pollutants in aqueous samples

Summary An on-line, solid-phase extraction gas chromatography atomic-emission detection (SPE-GC-AED) system has been set up using an on-column interface to transfer 100 l of desorbing solvent to the GC part of the system. Analytical characteristics such as recovery, precision and linearity of calibration plots were comparable with those of the off-line combination of SPE-GC-AED using organophosphorus pesticides as test compounds. The fully on-line set-up causes a marked improvement in detection because of the quantitative transfer of the analytes from the SPE module to the GC: detection limits are as low as 5–20 ng l^–1 for the analysis of 10 ml raw and spiked surface water samples using the phosphorus channel. Detection levels can be further enhanced by processing up to 100 ml samples. The integrated analytical system is robust. The potential of the on-line set up has been demonstrated for the analysis of surface water and waste water.     

Chemically modified polymeric sorbents for sample preconcentration

Solid-phase extraction is an attractive alternative in sample preparation because it overcomes many drawbacks of liquid-liquid extraction and makes on-line determination possible by hyphenation with chromatographic techniques. Driven by the need for more effective and more selective sorbents, advances in solid-phase extraction include the development of new materials. This paper describes different types of chemically modified sorbents for the solid-phase extraction of compounds from aqueous samples. Chemical introduction of different functional groups into a polymeric resin improves the efficiency of solid-phase extraction by providing better surface contact with the aqueous samples; also, these sorbents have a greater capacity than the typical solid-phase materials for polar compounds have. The most important new sorbents are the chemically modified resins based on styrene-divinylbenzene copolymers. Preparation of these new sorbents is described, and advantages and drawbacks of off-line procedures and on-line procedures are also discussed. Applications for off-line and on-line chromatographic determinations of polar compounds are presented.     

Multiresidue Analysis of Phenylurea Herbicides in Environmental and Drinking Water by Capillary Electrophoresis

The present paper describes the application of capillary electrophoresis in the micellar mode to the separation and quantitative determination of five phenylurea herbicides, viz. monuron, linuron, diuron, isoproturon, and monolinuron, in water samples. Using uncoated fused silica capillary and phosphate-borate buffer (pH 7.0) containing SDS, the five pesticides are resolved in less than 15 min and quantitatively determined by an ultraviolet detector at 244 nm. Method optimization and validation parameters are presented. Good linearity and repeatability were observed for all the compounds studied (correlation coefficients 0.999). The feasibility of the method developed was tested by simultaneous determination of these herbicides in environmental and drinking water samples at the minimum residue levels (MRLs) (0.1 μg/L) after solid-phase extraction (SPE) preconcentration procedure.     

Development of an analytical system for the simultaneous determination of anabolic macrocyclic lactones in aquatic environmental samples

An analytical procedure that enables routine analysis for trace determination of six anabolic macrocyclic lactones (zearalenone, alpha- and beta-zearalenol, zearalanone, zeranol, and taleranol) in sewage treatment plant (STP) samples has been developed. The method uses solid-phase extraction, followed by high-performance liquid chromatography with on-line tandem mass spectrometry using atmospheric pressure chemical ionization (LC/APCI-MS/MS). The extraction of these compounds from filtered water samples was performed off-line with C(18) solid-phase cartridges. The detection was achieved by isocratic reversed-phase high-performance liquid chromatography coupled with an heated nebulizer (HN) APCI interface operating in negative ion mode. Mean recovery of the analytes in STP effluent samples generally exceeded 81%. This method was used to determine the occurrence of target analytes in the aquatic environment. In the selected STP effluent samples, zearalenone and alpha-zearalenol were detected in the ng/L range.     

Flow-assisted automated solid-phase microextraction for the determination of chloroethers in aqueous matrices

In this study a method of flow-assisted automated solid-phase microextraction (FA-SPME) was developed for the determination of organic pollutants in aqueous samples. A CTC Combi-PAL autosampler coupled with gas chromatography–mass spectrometry (GC–MS) was used to automate the entire extraction process. In this method, the SPME fibre was exposed to 100 mL of sample in a direct immersion mode for 10 min. After exposure, the fibre was desorbed at the injection port of GC–MS. To demonstrate the applicability of FA-SPME, chloroethers were selected as model compounds. Good linear correlation was found over a concentration range of 0.5–100 µg/L. The detection limits of the method were determined between 0.02 and 0.05 µg/L with the coefficients of determination (R²) from 0.9980 to 0.9996. The relative standard deviations (RSDs) of the FA-SPME for three sequential FA-SPME analyses were determined to be in the range between 1.2% and 6.2% (n = 3). The applicability of the method was assessed by means of recovery studies and satisfactory values for all compounds were obtained. This optimised method was used in the analysis of water and human urine samples to show the matrix effect on FA-SPME. This FA-SPME/GC–MS is substantially faster and suitable for the routine continuous flow-mode environmental monitoring applications.     

A new apparatus for the extraction of organic compounds from aqueous solutions

A new apparatus for the extraction of organic compounds from sea water is described. With this apparatus it is possible to extract 54 standard compounds with high recovery percentages from 9 1 of sea water with 3 ml ofn-hexane. The analysis time (about 1 h) is appreciably lower than those of the extraction methods based on RP-18 and Carbopack-B adsorption (about 15 h). Furthermore, it is possible to analyze samples without filtration. An application of this method to the analysis of Tirreno sea water is reported.     

Comparison of Solid-Phase Extraction and Liquid-Liquid Extraction Methods for Liquid Chromatographic Determination of Diltiazem and its Metabolites in Plasma

Abstract

A rapid solid-phase extraction method for the determination of diltiazem and its metabolites from plasma was compared to a conventional liquid-liquid extraction procedure we have described previously. Analytical recovery for all compounds was greater than 90 % for solid-phase extraction whereas for liquid-liquid extraction, mean recovery ranged from 67 to 82 %. The increase of extraction efficiency was closely related to an improvement of the detection limit for the metabolites. Solid phase extraction procedure was found to be more convenient, rapid and sensitive than liquid-liquid extraction and represents a useful analytical tool for the monitoring of diltiazem and its metabolites in clinical investigations.