Synthesis of polystyrene-polysiloxane side-chain liquid crystalline block copolymers

The synthesis of a new liquid crystalline block copolymer consisting of a polystyrene block and a side-chain liquid crystalline siloxane block is reported. The synthetic approach described is based on the anionic polymerization of styrene and cyclic trimethyltrivinyltrisiloxane monomers, followed by functionalization of the siloxane block with side chain mesogens. The siloxane block has a T_g well below 25°C and is designed to exhibit a chiral smectic C^* phase at room temperature. These block copolymers are the first side-chain liquid crystalline block copolymers which contain both a high T_g glassy block and a low T_g liquid crystalline block.     

Grafting by in situ coupling of epoxy groups of a living copolymer with an anionic living polymer

A tetrahydrofuran (THF) solution of the living random copolymer of methyl methacrylate (MMA) and glycidyl methacrylate (GMA) was prepared by the living anionic copolymerization of the two monomers, using 1,1‐diphenylhexyllithium (DPHLi) as initiator, in the presence of LiCl ([LiCl]/[DPHLi]₀ = 3), at −50°C. The copolymer thus obtained has a controlled composition and molecular weight and a narrow molecular weight distribution. By introduction of an anionic living polystyrene (poly(St)) or anionic living polyisoprene (poly(Is)) solution into the above system at −30°C, a coupling reaction took place and a graft copolymer with a polar backbone and nonpolar side chains was produced. The solvent used in the preparation of the living poly(St) or poly(Is) affects the coupling reaction. When benzene was the solvent, a graft copolymer of high purity, controlled graft number and molecular weight, and narrow molecular weight distribution (M_w/M_n = 1.11–1.21) was obtained. In the coupling reaction, the living poly(St) reacted only with the epoxy groups and not with the carbonyls of the backbone polymer. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 105–112, 1999     

Anionic dispersion polymerization of styrene. I. Investigation of parameters for preparation of uniform micron-size polystyrene particles with narrow molecular weight distribution

Anionic dispersion polymerization in a hexane medium has been applied to the synthesis of monodisperse polystyrene particles in the size range of 1.41–6.16 μm, and having narrow molecular weight distributions M_w/M_n of 1.02–1.28. sec-Butyllithium was used as the initiator. Polystyrene-block-polybutadiene diblock copolymer containing 23% polystyrene block, (i.e., Stereon 730A) with a molecular weight of 147,000 g/mol and a polydispersity of 1.05, was found to be a suitable steric stabilizer for the preparation of micron-size polystyrene particles with narrow size distribution. Tetrahydrofuran (THF) was used as a promoter for obtaining narrow molecular weight distributions. However, this study revealed that the addition of small amounts of THF as promoter broadened the particle size distribution. High solids content polystyrene dispersions were also prepared without using any promoter by both batch and/or multi-addition monomer processes. © 1996 John Wiley & Sons, Inc.     

Viscoelastic behavior,order-disorder transition,and phase equilibria in mixtures of a block copolymer and an endblock-associating resin

The viscoelastic behavior, order-disorder transition, and phase equilibria in mixtures of a block copolymer and an endblock-associating resin were investigated. The block copolymer was a polystyrene-block-polyisoprene-block-polystyrene (KRATON® D-1107, Shell Development Co.) copolymer. The endblock-associating resins investigated were two different grades of a commercially available random copolymer of poly(α-methyl styrene) and polystyrene, one with a weight-average molecular weight \[\bar M_{\rm w}\] of 710 (KRISTALEX® 3085, Hercules Inc.) and the other with \[\bar M_{\rm w}\] = 4100 (KRISTALEX® 5140, Hercules Inc.). Mixtures of various proportions of the block copolymer and the endblock-associating resin were prepared in toluene solvent. With the mixtures, measurements of dynamic viscoelastic properties were made, namely, dynamic storage modulus G″ and dynamic loss modulus G″ as a function of temperature from temperature scans of the samples using a Rheometrics Mechanical Spectrometer. The following observations were made. (1) The plateau modulus of the block copolymer increased with increasing amount of KRISTALEX 3085 or KRISTALEX 5140, indicating that the low-molecular-weight resin was associated with the polystyrene microdomains of the block copolymer. (2) When KRISTALEX 3085 (up to 30 wt %) was added to the block copolymer, the glass transition temperature (T_g) of the polyisoprene midblock of the SIS block copolymer was shifted toward higher temperatures, indicating that part of the KRISTALEX 3085 added had associated with the rubbery midblock of the block copolymer. Also investigated was the order-disorder transition behavior of the mixtures, using a rheological technique (log G′ versus log G″ plots) recently introduced by Han and Kim. It has been found that the order-disorder transition temperature T_r of mixtures of the SIS block copolymer and KRISTALEX 3085 decreased steadily with increasing amount of KRISTALEX 3085, whereas the addition of KRISTALEX 5140 increased the T_r of the block copolymer. It was found by light scattering and hot-stage microscopy that macrophase separation occurred in the KRATON 1107/KRISTALEX 5140 mixtures while microdomains of polystyrene were present in the block copolymer.     

Graft polymers with macromonomers. II. Copolymerization kinetics of methacrylate-terminated polystyrene and predicted graft copolymer structures

Copolymerization studies of methacrylate-terminated polystyrene macromonomers (M₁) with several comonomers (M₂) verified the modified kinetic scheme and permitted prediction of graft polymer compositions and structures. Instantaneous and cumulative copolymer compositions, average graft distributions, and grafts per molecule are predicted from FORTRAN IV or BASIC programs. The r₂ relative reactivity ratios determined from styrene copolymerization (0.61) or from low conversion acrylic monomer in aqueous suspension (～0.4) had good agreement with literature values (about 0.6 and 0.4, respectively). Decreased macromonomer reactivity determined at high acrylic monomer conversions was attributed to phase separation phenomena. The Macromers also exhibited lower reactivity than predicted when copolymerized with acrylic monomers in DMSO/benzene solutions (r₂ ～ 0.8).     

Synthesis of poly(vinylidene fluoride)‐b‐poly(styrene sulfonate) block copolymers by controlled radical polymerizations

Block copolymers based on poly(vinylidene fluoride), PVDF, and a series of poly(aromatic sulfonate) sequences were synthesized from controlled radical polymerizations (CRPs). According to the aromatic monomers, appropriate techniques of CRP were chosen: either iodine transfer polymerization (ITP) or atom transfer radical polymerization (ATRP) from PVDF‐I macromolecular chain transfer agents (CTAs) or PVDF‐CCl₃ macroinitiator, respectively. These precursors were produced either by ITP of VDF with C₆F₁₃I or by radical telomerization of VDF with chloroform, respectively. Poly(vinylidene fluoride)‐b‐poly(sodium styrene sulfonate), PVDF‐b‐PSSS, block copolymers were produced from both techniques via a direct polymerization of sodium styrene sulfonate (SSS) monomer or an indirect way with the use of styrene sulfonate ethyl ester (SSE) as a protected monomer. Although the reaction led to block copolymers, the kinetics of ITP of SSS showed that PVDF‐I macromolecular CTAs were not totally efficient because a limitation of the CTA consumption (56%) was observed. This was probably explained by both the low activity of the CTA (that contained inefficient PVDF‐CF₂CH₂? I) and a fast propagation rate of the monomer. That behavior was also noted in the ITP of SSE. On the other hand, ATRP of SSS initiated by PVDF‐CCl₃ was more controlled up to 50% of conversion leading to PVDF‐b‐PSSS block copolymer with an average number molar mass of 6000 g·mol^?1. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Directly copolymerized poly(arylene sulfide sulfone) disulfonated copolymers for PEM‐based fuel cell systems. I. Synthesis and characterization

Direct aromatic nucleophilic substitution polycondensations of disodium 3,3′‐disulfonate‐4,4′‐difluorodiphenylsulfone (SDFDPS), 4,4′‐difluorodiphenylsulfone (DFDPS) (or their chlorinated analogs), and 4,4′‐thiobisbenzenethiol in the presence of potassium carbonate were investigated. Electrophilic aromatic substitution was employed to synthesize the SDFDPS comonomer in high yields and purity. High molecular weight disulfonated copolymers were easily obtained using the SDFDPS monomers, but in general, slower rates and a lower molecular weight copolymer were obtained using the analogous chlorinated monomers. Tough and ductile membranes were solution cast from N,N‐dimethylacetamide for both series of copolymers. The degrees of disulfonation (20–50%) were controlled by varying the ratio of disulfonated to unsulfonated comonomers. Precise control of the ionic concentration, well‐defined ionic locations, and enhanced stability due to the deactivated position of the –SO₃H group are some of the suggested advantages of direct copolymerization of sulfonated monomers. Further publications will discuss additional characteristics of these copolymers that have the same repeat unit, but different molecular weights, using methanol permeability, water uptake, protonic conductivity, and dynamic mechanical analysis. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2964‐2976, 2005     

Effect of thermal history on the ionic conductivity of block copolymer electrolytes

We have studied the effect of thermal history on ionic conductivity of block copolymer electrolytes. Previous work on block copolymer electrolytes composed of polystyrene‐b‐poly(ethylene oxide) (SEO) and lithium bis(trifluoromethanesulfone) imide (LiTFSI) salt was restricted to lamellar morphologies. This study addresses both cylindrical and lamellar morphologies. The conductivity of low molecular weight samples decreases after they are annealed. In contrast, the conductivity of high molecular weight samples is generally unaffected by annealing. These results are explained in the context of connectivity and composition of the conducting phase. © 2013 Wiley Periodicals, Inc. J. Polym. Sci. Part B: Polym. Phys. 2013 , 51, 927–934     

Block copolymer compatibilizers for polystyrene/poly(dimethylsiloxane) blends

Symmetric polystyrene (PS)–poly(dimethylsiloxane) (PDMS) diblock copolymers were mixed into a 20% dispersion of PDMS in PS. The effect of adding the block copolymer on the blend morphology was examined as a function of the block copolymer molecular weight (M_n,bcp), concentration, and viscosity ratio (η_r). When blended together with the PS and PDMS homopolymers, most of the block copolymer appeared as micelles in the PS matrix. Even when the copolymer was preblended into the PDMS dispersed phase, block copolymer micelles in the PS matrix phase were observed with transmission electron microscopy after mixing. Adding 16 kg/mol PS–PDMS block copolymer dramatically reduced the PDMS particle size, but the morphology, as examined by scanning electron microscopy, was unstable upon thermal annealing. Adding 156 kg/mol block copolymer yielded particle sizes similar to those of blends with 40 or 83 kg/mol block copolymers, but only blends with 83 kg/mol block copolymer were stable after annealing. For a given value of M_n,bcp, a minimum PDMS particle size was observed when η_r ～ 1. When η_r = 2.6, thermally stable, submicrometer particles as small as 0.6 μm were observed after the addition of only 3% PS–PDMS diblock (number‐average molecular weight = 83 kg/mol) to the blend. As little as 1% 83 kg/mol block copolymer was sufficient to stabilize a 20% dispersion of 1.1‐μm PDMS particles in PS. Droplet size reduction was attributed to the prevention of coalescence caused by small amounts of block copolymer at the interface. The conditions under which block copolymer interfacial adsorption and interpenetration were facilitated were explained with Leibler's brush theory. © 2002 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 40: 346–357, 2002; DOI 10.1002/polb.10098     

Phase separation in semicrystalline blends of poly(phenylene sulfide) and poly(ethylene terephthalate). II. Effect of poly(phenylene sulfide) homopolymer solubilization of PPS‐graft‐PET copolymer on morphology and crystallization behavior

The morphology and crystallization behavior of poly(phenylene sulfide) (PPS) and poly(ethylene terephthalate) (PET) blends compatibilized with graft copolymers were investigated. PPS‐blend‐PET compositions were prepared in which the viscosity of the PPS phase was varied to assess the morphological implications. The dispersed‐phase particle size was influenced by the combined effects of the ratio of dispersed‐phase viscosity to continuous‐phase viscosity and reduced interfacial tension due to the addition of PPS‐graft‐PET copolymers to the blends. In the absence of graft copolymer, the finest dispersion of PET in a continuous phase of PPS was achieved when the viscosity ratio between blend components was nearly equal. As expected, PET particle sizes increased as the viscosity ratio diverged from unity. When graft copolymers were added to the blends, fine dispersions of PET were achieved despite large differences in the viscosities of PPS and PET homopolymers. The interfacial activity of the PPS‐graft‐PET copolymer appeared to be related to the molecular weight ratio of the PPS homopolymer to the PPS segment of the graft copolymer (M_H/M_A). With increasing solubilization of the PPS graft copolymer segment by the PPS homopolymer, the particle size of the PET dispersed phase decreased. In crystallization studies, the presence of the PPS phase increased the crystallization temperature of PET. The magnitude of the increase in the PET crystallization temperature coincided with the viscosity ratio and extent of the PPS homopolymer solubilization in the graft copolymer. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 599–610, 2000     

Synthesis and characterization of block copolymers from 2‐vinylnaphthalene by anionic polymerization

The anionic polymerization of 2‐vinylnaphthalene (2VN) has been studied in tetrahydrofuran (THF) at ?78 °C and in toluene at 40 °C. 2VN polymerization in THF, toluene, or toluene/THF (99:1 v/v) initiated by sec‐butyllithium (sBuLi) indicates living characteristics, affording polymers with predefined molecular weights and narrow molecular weight distributions. Block copolymers of 2VN with methyl methacrylate (MMA) and tert‐butyl acrylate (tBA) have been synthesized successfully by sequential monomer addition in THF at ?78 °C initiated by an adduct of sBuLi–LiCl. The crossover propagation from poly(2‐vinylnaphthyllithium) (P2VN) macroanions to MMA and tBA appears to be living, the molecular weight and composition can be predicted, and the molecular weight distribution of the resulting block copolymer is narrow (weight‐average molecular/number‐average molecular weight < 1.3). Block copolymers with different chain lengths for the P2VN segment can easily be prepared by variations in the monomer ratios. The block copolymerization of 2VN with hexamethylcyclotrisiloxane also results in a block copolymer of P2VN and poly(dimethylsiloxane) (PDMS) contaminated with a significant amount of homo‐PDMS. Poly(2VN‐b‐nBA) (where nBA is n‐butyl acrylate) has also been prepared by the transesterification reaction of the poly(2VN‐b‐tBA) block copolymer. Size exclusion chromatography, Fourier transform infrared, and ¹H NMR measurements indicate that the resulting polymers have the required architecture. The corresponding amphiphilic block copolymer of poly(2VN‐b‐AA) (where AA is acrylic acid) has been synthesized by acidic hydrolysis of the ester group of tert‐butyl from the poly(2VN‐b‐tBA) copolymer. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4387–4397, 2002     

Amphiphilic block and statistical copolymers with pendant glucose residues: Controlled synthesis by living cationic polymerization and the effect of copolymer architecture on their properties

Amphiphilic block and statistical copolymers of vinyl ethers (VEs) with pendant glucose residues were synthesized by the living cationic polymerization of isobutyl VE (IBVE) and a VE carrying 1,2:5,6‐di‐O‐isopropylidene‐D ‐glucose (IpGlcVE), followed by deprotection. The block copolymer was prepared by a two‐stage sequential block copolymerization, whereas the statistical copolymer was obtained by the copolymerization of a mixture of the two monomers. The monomer reactivity ratios estimated with the statistical copolymerization were r₁ (IBVE) = 1.65 and r₂ (IpGlcVE) = 1.15. The obtained statistical copolymers were nearly uniform with the comonomer composition along the main chain. Both the block and statistical copolymers had narrow molecular weight distributions (weight‐average molecular weight/number‐average molecular weight ∼ 1.1). Gel permeation chromatography, static light scattering, and spin–lattice relaxation time measurements in a selective solvent revealed that the block copolymer formed multimolecular micelles, possibly with a hydrophobic poly(IBVE) core and a glucose‐carrying poly(VE) shell, whereas the statistical copolymer with nearly the same molecular weight and segment composition was molecularly dispersed in solution. The surface properties of the solvent‐cast films of the block and statistical copolymer were also investigated with the contact‐angle measurement. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 459–467, 2001     

Characterization of chloroprene and maleic anhydride copolymer by 13C-NMR spectroscopy and pyrolysis GC/MS

The radical copolymerizations of chloroprene (CP) and maleic anhydride (MAH) were carried out with AIBN in 1,4-dioxane at 60°C. The monomer reactivity ratios were estimated as r₁ (CP) = 0.38 and r₂ (MAH) = 0.07. Microstructures in the copolymer of chloroprene (CP) and maleic anhydride (MAH) were investigated by 75.4 MHz ¹³C-and 300 MHz ¹H-NMR spectroscopies. Resonances were assigned to the monomer sequence dyads CC, CM, and MC (C = chloroprene, M = maleic anhydride). Well resolved fine structure in the ¹³C-NMR spectra showed that 1,2- and 3,4-structural chloroprene units were negligible in the copolymer. The pyrolysis characterization of the copolymer was also investigated by the pyrolysis gas chromatography mass spectrometry (GC/MS). The fragments of CP and MAH monomers and CP-MAH hybrid dimer, CO, and CO₂ were identified after pyrolysis of the copolymer. © 1994 John Wiley & Sons, Inc.     

Polymer nanoparticles with a sensitive CO2‐responsive hydrophilic/hydrophobic surface

Poly(methyl methacrylate) (PMMA) nanoparticles with a sensitive CO₂‐responsive hydrophilic/hydrophobic surface that confers controlled dispersion and aggregation in water were prepared by emulsion polymerization at 50 °C under CO₂ bubbling using amphiphilic diblock copolymers of 2‐dimethylaminoethyl methacrylate (DMAEMA) and N‐isopropyl acrylamide (NIPAAm) as an emulsifier. The amphiphilicity of the hydrophobic–hydrophilic diblock copolymer at 50 °C was triggered by CO₂ bubbling in water and enabled the copolymer to serve as an emulsifier. The resulting PMMA nanoparticles were spherical, approximately 100 nm in diameter and exhibited sensitive CO₂/N₂‐responsive dispersion/aggregation in water. Using copolymers with a longer PNIPAAm block length as an emulsifier resulted in smaller particles. A higher concentration of copolymer emulsifier led to particles with a stickier surface. Given its simple preparation and reversible CO₂‐triggered amphiphilic behavior, this newly developed block copolymer emulsifier offers a highly efficient route toward the fabrication of sensitive CO₂‐stimuli responsive polymeric nanoparticle dispersions. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2149–2156     

A new thermo‐responsive block copolymer with tunable upper critical solution temperature and lower critical solution temperature in the alcohol/water mixture

The multi‐thermo‐responsive block copolymer of poly[2‐(2‐methoxyethoxy)ethyl methacrylate]‐block‐poly[N‐(4‐vinylbenzyl)‐N,N‐diethylamine] (PMEO₂MA‐b‐PVEA) displaying phase transition at both the lower critical solution temperature (LCST) and the upper critical solution temperature (UCST) in the alcohol/water mixture is synthesized by reversible addition‐fragmentation chain transfer polymerization. The poly[2‐(2‐methoxyethoxy)ethyl methacrylate] (PMEO₂MA) block exhibits the UCST phase transition in alcohol and the LCST phase transition in water, while the poly[N‐(4‐vinylbenzyl)‐N,N‐diethylamine] (PVEA) block shows the UCST phase transition in isopropanol and the LCST phase transition in the alcohol/water mixture. Both the polymer molecular weight and the co‐solvent/nonsolvent exert great influence on the LCST or UCST of the block copolymer. By adjusting the solvent character including the water content and the temperature, the block copolymer undergoes multiphase transition at LCST or UCST, and various block copolymer morphologies including inverted micelles, core‐corona micelles, and corona‐collapsed micelles are prepared. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 4399–4412     

Polymerization of aromatic aldehydes. IV. Cationic copolymerization of phthalaldehyde isomers and styrene

Copolymerizations of three phthalaldehyde isomers (M₂) with styrene (M₁) were carried out in methylene chloride or in toluene with BF₃OEt₂ catalyst. The monomer reactivity ratios were r₁ = 0.77, r₂ = 0 for the meta isomer and r₁ = 0.60, r₂ = 0 for the para isomer. The second aldehyde group of both isomers did not participate in polymerization and acted simply as the electron-withdrawing group, thus reducing the cationic reactivity of these monomers. Copolymerization behaviors of the ortho isomer (o-PhA) were quite different between 0°C and ?78°C. At ?78°C, o-PhA preferentially polymerized to yield “living” cyclopolymers, until an equilibrium concentration of o-PhA monomer was reached. Then, styrene propagated from the living terminal rather slowly. The block structure of the copolymer was confirmed by the chemical and spectroscopic means. In the copolymerization at 0°C, the o-PhA unit in copolymer consisted both of cyclized and uncyclized units. This copolymer seemed to contain short o-PhA sequences. The variation of the o-PhA-St copolymer structure with the polymerization temperature was explained on the basis of whether the polymerization was carried out above or below the ceiling temperature (?43°C) of the homopolymerization of o-PhA.     

Synthesis of new amphiphilic diblock copolymers containing poly(ethylene oxide) and poly(α‐olefin)

This article discusses an effective route to prepare amphiphilic diblock copolymers containing a poly(ethylene oxide) block and a polyolefin block that includes semicrystalline thermoplastics, such as polyethylene and syndiotactic polystyrene (s‐PS), and elastomers, such as poly(ethylene‐co‐1‐octene) and poly(ethylene‐co‐styrene) random copolymers. The broad choice of polyolefin blocks provides the amphiphilic copolymers with a wide range of thermal properties from high melting temperature ～270 °C to low glass‐transition temperature ～?60 °C. The chemistry involves two reaction steps, including the preparation of a borane group‐terminated polyolefin by the combination of a metallocene catalyst and a borane chain‐transfer agent as well as the interconversion of a borane terminal group to an anionic (? O^?K⁺) terminal group for the subsequent ring‐opening polymerization of ethylene oxide. The overall reaction process resembles a transformation from the metallocene polymerization of α‐olefins to the ring‐opening polymerization of ethylene oxide. The well‐defined reaction mechanisms in both steps provide the diblock copolymer with controlled molecular structure in terms of composition, molecular weight, moderate molecular weight distribution (M_w/M_n < 2.5), and absence of homopolymer. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3416–3425, 2002     

Trials and tribulations of designing multitasking catalysts for olefin/thiophene block copolymerizations

Block copolymers containing both insulating and conducting segments have been shown to exhibit improved charge transport properties and air stability. Nevertheless, their syntheses are challenging, relying on multiple post‐polymerization functionalization reactions and purifications. A simpler approach would be to synthesize the block copolymer in one pot using the same catalyst to enchain both monomers via distinct mechanisms. Such multitasking polymerization catalysts are rare, however, due to the challenges of finding a single catalyst that can mediate living, chain‐growth polymerizations for each monomer under similar conditions. Herein, a diimine‐ligated Ni catalyst is evaluated and optimized to produce block copolymer containing both 1‐pentene and 3‐hexylthiophene. The reaction mixture also contains both homopolymers, suggesting catalyst dissociation during and/or after the switch in mechanisms. Experimental and theoretical studies reveal a high energy switching step coupled with infrequent catalyst dissociation as the culprits for the low yield of copolymer. Combined, these studies highlight the challenges of identifying multitasking catalysts, and suggest that further tuning the reaction conditions (e.g., ancillary ligand structure and/or metal) is warranted for this specific copolymerization. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 132–137     

Spacer length controlled highly thermo reversible polyurethane–urea based on polystyrene: synthesis and crystallization studies

Poly(urethane–urea) (PUU) is prepared using dihydroxy functionalized polystyrene having M_w 2000 g/mol, 1,6 hexamethylene diisocyanate and three different diamines (1,2‐ethylenediamine, 1,4‐butanediamine and 1,6‐hexamethylene diamine) by melt polymerization method. The synthesized copolymer is characterized by viscosity measurements, Fourier transform infrared (FT‐IR) spectroscopy, wide angle 2D‐X‐ray scattering (WAXS) and differential scanning colorimetry (DSC). The inherent viscosity of the polymers is found to be in the range of 0.4–0.5 dl/g, suggesting that the polymers are of high molecular weight. FT‐IR results conclude that the urea groups form both monodendate and bidendate assemblies. Temperature‐dependent FT‐IR and WAXS data confirm that the crystallinity of the copolymer is highly reversible and depends on the spacer length. DSC data also confirm that the crystallization pattern depends on the spacer length. The swelling behavior in water and the solubility of the polymer in chloroform are depending on the type of chain extender used in the PUU synthesis. Copyright © 2014 John Wiley & Sons, Ltd.     

Effects of Br connected groups on atom transfer nitroxide radical coupling reaction and its application in the synthesis of comb‐like block copolymers

The effects of Br connected groups on atom transfer nitroxide radical coupling (ATNRC) reaction were investigated. Two precursors methoxyl poly(ethylene oxide)‐b‐poly(ethylene oxide‐co‐2‐bromoiso butyryloxy glycidyl ether) (mPEO‐b‐Poly(EO‐co‐BiBGE)) and methoxyl poly(ethylene oxide)‐b‐poly(2‐bromoiso butyryloxy glycidyl ether) (mPEO‐b‐Poly(BiBGE)) with different ? C(CH₃)₂Br density were designed and synthesized firstly, and then ATNRC reaction were completed between these precursors and 2,2,6,6‐tetramethylpiperidinyl‐1‐oxy poly(ε‐caprolactone) (TEMPO‐PCL) in the presence or absence of St monomers, respectively. The results showed that the structure of Br connected groups showed an important effect on ATNRC reaction, and the ATNRC reaction with high efficiency could be realized by transforming the higher active Br connected groups into the lower one by the addition of small amount of St monomers. The final comb‐like block copolymers mPEO‐b‐[Poly(EO‐co‐Gly)‐g‐(St_1.8‐b‐PCL)] and mPEO‐b‐[Poly(Gly)‐g‐(St_2.4‐b‐PCL)] with high coupling efficiency were obtained by this strategy. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1633–1640, 2010