Melting of constrained drawn nylon 6 yarns

A differential scanning calorimeter (DSC) was used to study the melting behavior of drawn nylon 6 yarns which were prevented from shrinking during heating. The DSC curves exhibit a single melting peak at a higher temperature instead of the double peaks which, as reported previously, were observed in the unconstrained state. The curve is explained quantitatively in terms of the perfecting of the original crystals followed by monotonic melting of these crystals during heating. The single peak results from the absence of the partial melting–recrystallization process which plays an important role in the appearance of double peaks. The temperature of the melting peak for the constrained sample increases linearly with draw ratio, and is unaffected by drawing temperature and by annealing at constant length after drawing. The elevation of the melting temperature is discussed on the basis of the entropy effects predicted theoretically by Zachmann. Thermal analysis of constrained samples has proved to be useful for detecting oriented crystals which coexist with unoriented ones.     

热拉伸的超高分子量聚乙烯的晶体结构和力学性能

讨论了超高分子量聚乙烯（ＵＨＭＷ－ＰＥ）的熔融一次拉伸和二次拉伸的晶体结构和力学性能．利用ＷＡＸＤ和ＳＡＸＤ测定了拉伸片的晶体取向因子和极图，晶粒尺寸，晶体畸变，长周期等晶体结构．用ＤＳＣ和ＶＥＳ测定热性能和动态力学性能．应力－应变实验测定拉伸片的杨氏模量，断裂强度和伸长．这些实验结果说明ＵＨＭＷ－ＰＥ经二次拉伸能产生正交晶系的伸直链晶体．二次拉伸片由折叠链片晶和伸直链晶体两元结构组成．二次拉伸片的杨氏模量比一次拉伸片有大幅度提高．二次拉伸片的晶体结构和力学性能是在一次拉伸的基础上形成的．     

Nonisothermal crystallization and melting behavior of syndiotactic polypropylenes of different microstructure

Syndiotactic polypropylenes and their copolymers with 1‐olefins were synthesized using two metallocene/MAO catalytic systems, and the effect of the different microstructures on nonisothermal crystallization and subsequent melting was studied. Using differential scanning calorimetry (DSC) it was observed that samples with lower content of defects showed crystallization on cooling from the melt, and a double melting peak in the subsequent heating scan, the latter associated with melt, recrystallization and remelt processes that it was confirmed by its nonreversing exothermic process found by means of temperature modulated DSC (MDSC). However, polymers with high amount of defects showed cold crystallization on heating followed by a melting process, that it was observed by MDSC. Wide angle X‐ray diffraction was used for characterizing the changes of crystalline forms in relationship with crystallization process. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 798–806, 2008     

聚苯硫醚及其共混物的双熔融行为

聚苯硫醚及其共混物的双熔融行为麦堪成，章明秋，曾汉民，祁世成（中山大学材料科学研究所，广州，５１０２７５）关键词熔融行为，聚苯硫醚，共混物聚苯硫醚（ＰＰＳ）作为结晶型工程塑料，具有优异的力学性能，高的耐化学性以及良好的热稳定性．然而，结晶度高的ＰＰＳ...     

The multiple melting endotherms from poly(butylene terephthalate)

The melting behavior of poly(butylene terephthalate) (PBT) has been investigated, and a simulation has been performed to determine whether the multiple melting endotherms observed during the thermal analysis of PBT can be explained by the simultaneous melting and recrystallization of an initial distribution of crystal melting temperatures that contains only one maximum and two inflection points. Specimens that were cooled at constant rates from the melt showed between one and three melting endotherms upon heating in a differential scanning calorimeter (DSC). The position and breadth of the crystallization exotherms upon cooling from the melt and small-angle x-ray scattering showed that as the cooling rate is increased, the distribution of melting temperatures broadens and shifts to lower temperatures. By combining temperature-dependent recrystallization with an initial distribution of melting temperatures, simulated DSC curves were produced that agreed well with experimental DSC curves. In instances of triple peaked curves, the high temperature peak was due to crystals formed during the scanning process, and the middle and low temperature peaks were due to crystals originally present in the material. Satisfactory agreement between the experimental and simulated curves was found without considering additional crystallization from the amorphous regions during the scanning process.     

Crystallization behavior and morphology of poly(butylene succinate) modified with rosin maleopimaric acid anhydride

The melting behavior, crystallization behavior, and morphology of PBSR, which is Poly(butylene succinate) modified with rosin maleopimaric acid anhydride (RMA), were investigated with differential scanning calorimetry (DSC) and polarized optical microscope (POM). The multiple endotherms were ascribed to the recrystallization during DSC measurement and the equilibrium melting temperature determined by the Peak L, which was associated with the fusion of the crystals grown by normal primary crystallization, was 125.9 °C. After the kinetic parameters for isothermal crystallization of PBSR were determined by Avrami equation, to make a detailed regime transition analysis, the well‐established Lauritzen–Hoffman equation was employed. The results indicated that there were two regimes, regime II and regime III, in the range of higher and lower crystallization temperature, respectively. The regime transition temperature is about 81 °C. At last, the spherulitic morphologies of PBSR after being crystallized isothermally at different temperature were observed with the help of POM. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2694–2704, 2005     

Multiple melting behavior in isothermally crystallized poly(trimethylene terephthalate)

Melting behavior of poly(trimethylene terephthalate) (PTT) after isothermal crystallization from the melt state was studied using differential scanning calorimetry (DSC) and wide-angle X-ray diffraction (WAXD) techniques. The subsequent melting thermograms for PTT isothermally crystallized within the temperature range of 182-215 °C exhibited triple (for crystallization temperatures lower than ≈192 °C), double (for crystallization temperatures greater than ≈192 °C but lower than ≈210 °C), or single (for crystallization temperatures greater than ≈210 °C) endothermic melting phenomenon. These peaks were denoted peaks I, II, and III for low-, middle-, and high-temperature melting endotherms, respectively. For the triple melting phenomenon, it was postulated that the occurrence of peak I was a result of the melting of the primary crystallites, peak II was a result of the melting of recrystallized crystallites, and peak III was a result of the melting of the recrystallized crystallites of different stabilities. In addition, determination of the equilibrium melting temperature T_m⁰ for this PTT resin according to the linear and non-linear Hoffmann-Weeks extrapolation provided values of 243.6 and 277.6 °C, respectively.     

Characterisation of different inulin samples by DSC: Influence of polymerisation degree on melting temperature

Melting behaviour of powder inulin has been studied by differential scanning calorimetry. DSC curves show two endothermic peaks, relative to water elimination and to inulin melting, respectively. The second peak is dependent on inulin type and a shift to a higher temperature is observed with increasing average polymerisation degree (DP) of the sample. For similar crystallinity index, linear relations have been underlined and so predicting inulin mean DP can be done by DSC analysis. The study shows that a relatively high heating rate (25°C min^–1) can be used and brings a supplementary interest by an important reduction of analysis time.This revised version was published online in November 2005 with corrections to the Cover Date.     

Step-scan TMDSC and high rate DSC study of the multiple melting behavior of poly(1,3-propylene terephthalate)

The multiple melting behavior of poly(1,3-propylene terephthalate) (PPT) samples after isothermal crystallization from the melt was studied. The step-scan temperature-modulated differential scanning calorimetry (TMDSC) and high rate DSC were used to investigate this behavior in conjunction with standard DSC, wide-angle X-ray diffraction (WAXD) and polarizing light microscopy (PLM). The effect of PPT average molecular weight on the melting was also examined. In general multiple endotherms after isothermal crystallization of PPT were attributed to a continuous crystal perfection process during the subsequent heating scan via melting-recrystallization-remelting. Multiple melting behavior was more pronounced for the low molecular weight PPT. Step-scan TMDSC showed that extensive recrystallization occurs in PPT samples, especially after rapid isothermal crystallization. In fact two recrystallization exothermic peaks were observed. High rate DSC revealed the initial morphology generated during the isothermal step and showed that the low and middle peaks are associated with melting of primary crystals while the high temperature peak should be attributed to melting of recrystallized material.     

13C CP/MAS NMR studies of morphological changes in polypropylene: 2. The double melting endotherm of spunbonded fabrics

The double melting endotherm of spunbonded isotactic polypropylene (iPP) fabrics was investigated by monitoring changes in the solid-state NMR spectrum that result from thermal annealing. The DSC melting thermogram was found to change from a double to a single endotherm at anneal temperatures ≥156°C, with a concomitant increase in percent crystallinity. All of the carbon resonances in the CP/MAS NMR spectrum of the purely crystalline phase of iPP were found to be composed of multiple peaks with relative intensities that depend on anneal temperature. By monitoring the changes in the distribution of intensity among the various peaks of a given resonance, a transition temperature of 156°C was identified. Arguments are presented that this redistribution of intensity within a given carbon resonance characterizes the transformation from the α₁ to the α₂ monoclinic crystal form. The exothermicity associated with this transformation is responsible for the observation of a double melting endotherm by DSC. The splitting patterns observed in the NMR spectrum are discussed in terms of interlayer distances between layers of isochiral helices and the density of exposed methyls at the contact faces of these interlayers. © 1996 John Wiley & Sons, Inc.     

不同初始结构间规聚丙烯纤维熔融过程中的结晶转变行为

通过熔融纺丝及随后的热处理制备了具有不同初始结构的间规聚丙烯纤维(sPP).采用差示扫描量热仪(DSC)和变温广角X-射线衍射仪详细研究了sPP纤维在升温过程中的结构转变和熔融行为.结果表明,不同初始结构sPP纤维的晶型不同,卷绕纤维和退火处理纤维以Ⅰ型和Ⅱ型晶型为主,牵伸纤维介晶相占优;升高温度导致Ⅰ型和Ⅱ型两种晶型直接熔融,没有出现Ⅱ型向Ⅰ型的晶型转变;初始结构为介晶相的纤维在升温过程中部分介晶相直接转变为Ⅱ型晶型,还有一部分介晶相直接熔融,并在随后的升温过程中,形成Ⅰ型晶型.sPP纤维的多重熔融行为与其初始结构和纤维制备条件密切相关.     

Effect of supercritical carbon dioxide on the crystallization and melting behavior of linear bisphenol A polycarbonate

The crystallization and melting behavior of bisphenol A polycarbonate treated with supercritical carbon dioxide (CO₂) has been investigated with differential scanning calorimetry. Supercritical CO₂ depresses the crystallization temperature (T_c) of polycarbonate (PC). The lower melting point of PC crystals increase nonlinearly with increasing treatment temperature. This indicates that the depression of T_c is not a constant at the same pressure. T_c decreases faster at a higher treatment temperature than at a lower temperature. The leveling off of the depression in T_c at higher pressures is due to the antiplasticization effect of the hydrostatic pressure of CO₂. The melting curves of PC show two melting endotherms. The lower melting peak moves to a higher temperature with increasing treatment temperature, pressure, and time. The higher temperature peak moves toward a higher temperature as the treatment temperature is increased, whereas this peak is independent of the treatment pressure, time, and heating rate. The double melting peaks observed for PC can be attributed to the melting of crystals with different stability mechanisms. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 280–285, 2004     

Influence of uniaxial draw on near-surface structure in poly(ethyleneterephthalate)

Relative amounts of surface crystallinity and amorphous structure and their respective surface orientations were examined as a function of depth from the surface for a series of uniaxially drawn poly(ethyleneterephthalate) (PET) films using polarized attenuated total-reflectance infrared spectroscopy (ATR-IR). Qualitative depth resolution on a scale from ca. 0.5 to 5 μm is obtained. The results indicate a higher degree of extended trans segments and a higher degree of extended trans orientation near the surface in the machine direction, relative to the bulk film. These quantities also increase with increasing uniaxial draw ratio. No evidence for orientation of the gauche conformer at the surface as a function of uniaxial draw ratio is observed. All conclusions are consistent with the presence of increased crystallinity at the surface of the films. Increases in trans structure and orientation measured by ATR-IR measurements are consistent with bulk crystallinity measurements from density and x-ray scattering measurements.     

热历史对尼龙1212熔融行为的影响

利用DSC方法研究了不同热历史条件对尼龙1212熔融行为的影响.不同的热历史条件下,在DSC曲线上,观察到尼龙1212产生2个或3个熔融峰,依据聚合物结晶理论,对各峰的来源进行了分析.在160℃下不同温度退火120 min的尼龙1212样品DSC曲线上,低温结晶熔融峰主要由低温结晶形成的一些微晶体或者片晶熔融产生,其晶体完善程度较差,熔融峰值较低,峰面积较小;主熔融峰是由样品在淬火过程中形成的晶体和升温过程中低温结晶形成的晶体的熔融重结晶形成较为完善的晶体熔融所产生,熔融峰值较高,峰面积较大.在不同的升温速率条件下,熔融峰温度有所移动,表明不同升温速率条件下产生的熔融峰的结晶晶型是相同的.在不同结晶时间下结晶,延长结晶时间对较高完善程度晶体的生长有利.在不同温度下依次退火处理的样品,熔融产生两个附加峰,这两个附加峰的峰温都比它们相应的退火温度高,而峰高和峰面积随退火温度降低而减小.根据等温结晶结果,由Hoffman方法确定了尼龙1212的平衡熔融温度为202.8℃.     

Plastic deformation of polyethylene II. Change of mechanical properties during drawing

The crystallinity, elastic modulus, and tensile strength of samples of various draw ratios together with the true stress—strain curves of high-density polyethylene were determined to establish correlations with morphological changes occurring during deformation. Changes of crystallinity at draw ratios below 5, i.e., constancy during drawing of quenched film and a decrease during drawing of annealed film, are explained by the formation of microfibrils with crystallinity independent of the thermal history of the film. The microfibrils slide past each other at higher draw ratios, generating an increasing number of interfibrillar tie molecules, which is reflected in the increasing number of interfibrillar tie molecules, which is reflected in the increase of crystallinity, elastic modulus, and tensile strength. From the true stress—strain curves, the differential work density for the deformation of the volume element was calculated as a function of the draw ratio. It contains two components which reflect two different mechanisms of deformation. The first component, decreasing with increasing draw ratio, can be associated with the destruction of the original microspherulitic structure; the second one, increasing with increasing draw ratio, can be associated with the deformation of the new fiber structure, i.e., with the sliding motion of the microfibrils formed during the first deformation step.     

含间位取代苯基聚醚酮酮的结晶与晶体结构研究

通过差示扫描法（ＤＳＣ）及广角Ｘ 射线衍射（ＷＡＸＤ）技术研究了含间位取代苯基聚醚酮酮（ＰＥＫｍＫ）的结晶行为与晶体结构．Ｘ 射线结果表明，从熔融态及玻璃态结晶时，ＰＥＫｍＫ只有一种晶型，其晶胞参数为：ａ＝０７６７２ｎｍ，ｂ＝０６１４９ｎｍ，ｃ＝１５９９ｎｍ．ＤＳＣ结果表明，ＰＥＫｍＫ热分析曲线都出现了熔融双峰，低熔融峰（ＤＯＷｎ）热焓占总热焓４～７％，它源于初始结晶形成的同一晶型不同厚度片晶．低熔融峰在２５０℃以上结晶转化成高熔融峰（Ｉ），ＰＥＫｍＫ平衡熔点为２９５℃     

Thermoanalytical investigation of lignite humic acids fractions

Differential scanning calorimetry (DSC) and thermogravimetry (TG) studies of humic acids (HA) sequentially extracted at pH 7, 8, 9 and 10 by phosphate and pyrophosphate buffers have been carried out. Supplement information were provided by elementary analysis and FTIR spectroscopy to characterize and evaluate in details the thermooxidative behavior of HA fractions. The exothermic DSC profiles of the HA samples extracted by phosphate buffers or by pyrophosphates were shifted to lower temperatures in comparison with the original sample and showed narrow distribution of humic molecules. Experimental data showed dependency of HA fraction composition on the pH used during extraction. DSC experimental data showed 1 endothermic and from 2-5 exothermic peaks associated with mass loss recorded by TG measurement. Higher degree of aliphaticity observed on samples extracted at lower pH did not remarkably affect the DSC peak temperature of the first decomposition step associated with aliphatic moieties and functional groups decomposition and recombination reactions. On the other hand, such dependency was observed in higher temperature range where destruction of aromatic structures took part. The behavior of HA samples (even after separation of specific fractions) showed high complexity of system, which resulted in complicated physical and chemical processes occurred during thermooxidation. Observed stability and released heat were affected by many factors, among them evaporation of volatile part of humic matter and a slight contribution of weak interactions among humic molecules were considered. This revised version was published online in August 2006 with corrections to the Cover Date.     

Thermoanalytical investigations of extended and annealed keratins

DSC investigations have been used to characterize the microfibril-matrix complex of keratin consisting of helical low-sulfur microfibrils in a nonhelical high-sulfur matrix. The corresponding DSC curves display one or two endothermic peaks in the temperature range 230°–255°C. The first peak is a microfibrillar peak and the second one a matrix peak (cystine decomposition peak). DSC investigations of extended keratins have shown that the microfibrillar peak is a helix peak. DSC investigations of annealed keratins confirm our earlier assumption that the helix peak is no helix melting peak but an irreversible helix unfolding, superimposed by various decomposition reactions. The matrix peak of the above described keratin samples is less reproducible than the corresponding helix peak and cannot be used for further characterization studies of keratins.Dedicated to Professor E. G. Klesper on the occasion of his 60th birthday.     

Influence of additives on the crystal structure and melting behavior of poly(ethylene‐2,6‐naphthalene dicarboxylate)

The influence of additives on the crystal modification and melting behavior of poly(ethylene‐2,6‐naphthalene dicarboxylate) (PEN) was investigated with wide‐angle X‐ray diffraction and differential scanning calorimetry (DSC). The addition of a nucleating promoter, Ceraflour 993, had no effect on the crystal modification and melting behavior of PEN crystallized under all chosen experimental conditions. However, the addition of a nucleating agent, sodium benzoate (SB), did affect the crystal modification and melting behavior of PEN when PEN/SB was crystallized at a higher temperature, but not at a lower temperature. A mixture of α and β modifications of PEN was obtained, and an overlapped dual melting peak was observed in DSC curves when PEN was crystallized at a higher temperature in the presence of SB, instead of a single crystal form and a single melting peak for the crystallization of pure PEN. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 296–301, 2004     

等规聚丙烯在γ射线辐照下的链结构和结晶行为

利用凝胶渗透色谱(GPC)、傅里叶变换红外光谱(FTIR)和示差扫描量热(DSC)等手段对不同剂量γ射线辐照后等规聚丙烯(iPP)的分子链结构及结晶行为的变化进行了研究.结果表明,γ射线辐照使iPP的分子量下降,并在其分子链中产生羟基和羰基等极性基团,从而影响其结晶行为.在非等温结晶过程中,当辐照剂量≤50 kGy时,iPP的热结晶温度略有升高;增大辐照剂量,iPP的热结晶温度明显降低.iPP的熔融温度则随辐照剂量的增大而降低,且分裂成双峰.利用Avrami方程研究了辐照前后iPP的等温结晶动力学,发现辐照前后样品的Avrami指数n都在3左右,表明iPP的结晶遵循异相成核机理,且不受辐照剂量和等温结晶温度的影响,但总结晶速率随等温结晶温度和辐照剂量的升高而逐渐减小.探讨了iPP经过γ射线辐照后,分子链断裂、链结构变化和结晶速率之间的关系.