Preconcentration of metal ions using an immobilized dialkyldithiocarbamate in a flow system

Flow injection analysis with on-line preconcentration using a minicolumn loaded with dialkyldithiocarbamate immobilized on controlled pore glass is described for the determination of Rh(III), Co²⁺, Cu²⁺, Hg²⁺, and Hg₂²⁺. The detection limits range from 0.05 ng ml⁻¹ for Cu²⁺ to 50 ng ml⁻¹ for Hg²⁺ for 5- or 10-ml samples, improvement of 2–3 orders of magnitude compared with direct injection. The operating conditions are optimized and the effects of interferents are studied. The capacity of the collector varied from 0.9 mmol g⁻¹ for Rh(III) to ca 4 mmol g⁻¹ (Co²⁺, Cu²⁺, Hg²⁺).     

Determination of selenomethionine by high performance liquid chromatography-direct hydride generation-atomic absorption spectrometry

A simple, reliable, trace determination of selenomethionine (Semet) based on a direct hydride generation atomic absorption spectrometric method was developed using sodium tetrahydroborate (0.3% in 0.2% NaOH) and hydrochloric acid (3 M). The method excluded any chemical pretreatment prior to hydride generation (HG). The optimized HG system was successfully coupled with the HPLC system. The detection limit (3σ of blank; n=5), reproducibility (R.S.D. of three successive analyses/day, performed on three different days), and repeatability (R.S.D. of three successive analyses) of the method were 1.08 ng ml⁻¹, 9.8% for 9.04 ng ml⁻¹ and 2.1–9.5% for 30.0–1.27 ng ml⁻¹ Semet as Se (standards prepared in Milli-Q water). Calibration graph was linear up to 30 ng ml⁻¹. This HPLC-HG-AAS method is very promising and successfully determined Semet (spiked) in human urine.     

Occurrence of ochratoxin A in Turkish wines

A total of 95 wine samples including 34 white, 10 rosé and 51 red wines originating from four different Turkish areas were analysed for ochratoxin A (OTA). An analytical method based on immunoaffinity column (IAC) for clean-up and high performance liquid chromatography with fluorescence detection (HPLC-FD) was used to determine OTA in wines. The limit of detection (LOD) was estimated as 0.006 ng ml^− 1 for white wine and 0.010 ng ml^− 1 for rosé and red wines. The limit of quantification (LOQ) was estimated as 0.020 ng ml^− 1 in white wine and 0.030 ng ml^− 1 in rosé and red wines. Recovery experiments were carried out with spiked samples in the range 0.1–1 ng ml^− 1 of OTA. The average OTA recoveries from spiked white wine samples varied from 79.43% to 85.07%; while the mean recoveries for rosé and red wine samples were in the range of 77.48–83.96% and 76.61–83.55%, respectively. OTA was detected in 82 (86%) wine samples at levels of < 0.006–0.815 ng ml^− 1, which were below the maximum allowable limit established by the European Community. The mean OTA concentration in red wines was slightly higher than in white and rosé wines. Furthermore, our data indicate that the geographic region of origin has strong influence on OTA level for white, rosé and red wines: wines originating from Thrace (n = 44, mean = 0.158 ng ml^− 1) and Aegean (n = 28, mean = 0.060 ng ml^− 1) regions of Turkey were more contaminated with OTA compared with wines originating from central (n = 15, mean = 0.027 ng ml⁻¹) and east Anatolia (n = 8, mean = 0.027 ng ml^− 1) areas. This study showed that the occurrence of OTA in Turkish wines is high, but at levels that probably leads to a non-significant human exposure to OTA by consumption of wines.     

Speciation of silicon and phosphorous using liquid chromatography coupled with sector field high resolution ICP-MS

Sector-field high resolution inductively coupled plasma mass spectrometry (HR-ICP-MS) has been used, at R=3000, to resolve spectral interferences caused by N₂⁺ and CO⁺ on ²⁸Si⁺, and NOH⁺ and NO⁺ on ³¹P⁺, thereby facilitating the speciation of these elements. Polydimethylsiloxanes (PDMS), ranging from 162 g mol⁻¹ to 16 500 g mol⁻¹, and their silanol breakdown products, have been separated by size exclusion and reverse phase chromatography, respectively, and detected using HR-ICP-MS. Detection limits (as Si) of between 12–30 ng ml⁻¹ and 0.1–4 ng ml⁻¹ were obtained for the PDMS and silanol compounds, respectively. Quantitative and reproducible methods have been developed for the analysis of four common organophosphorous pesticides in blood plasma, and inorganic phosphates in food, with detection limits of between 0.9–2 ng ml⁻¹ and 1–39 ng ml^−1, respectively.     

Flow Injection Chemiluminescence Determination of Isoniazid Using On-Line Electrogenerated Manganese(III) as Oxidant

A novel flow injection chemiluminescence (CL) system for the determination of isoniazid has been proposed. It is based on the direct CL reaction of isoniazid and Mn(III) in sulfuric acid medium. The unstable Mn(III) was on-line electrogenerated by constant current electrolysis. The CL emission intensity was linear with isoniazid concentration in the range 0.1–10 μg/mL; the detection limit was 3.2 × 10⁻² μg/mL. The whole process could be completed in 1 min with a relative standard deviation of less than 5%. The proposed method is suitable for automatic and continuous analysis and has been applied successfully to the analysis of isoniazid in pharmaceutical preparation.     

Simultaneous determination of cobalt and chromium by ion chromatography with chemiluminescence detection and its application to glass analysis

A method is described for the simultaneous determination of very low levels of Co and Cr by high performance ion chromatography coupled with a chemiluminescence detection system. 0.1M K₂SO₄ solutions, adjusted to pH 3.0, were used as eluent to separate Co(II) and Cr(III) between them and from interferents. The detection system was the chemiluminescence of luminol/ H₂O₂ in alkaline medium catalyzed by such transition metals. Using a matrix solution analogous to soda-lime silica glass (dissolved in acids) calibration graphs were linear up to 0.5 ng ml^–1 for cobalt and up to 250 ng ml^–1 for chromium. The corresponding calculated detection limits (3 s) in such matrix were 0.05 ng ml^–1 and 15 ng ml^–1 for Co and Cr, respectively. The relative standard deviations were 1.4% at 0.5 ng ml^–1 Co level and 2.8% at the 200 ng ml^–1 Cr level. No interferences were observed from the more common metals, particularly those present in glass samples. The ion chromatography/ chemiluminescent method proposed has been successfully applied to the analysis of Co and Cr in glasses.     

Column preconcentration of gold by adsorbing AuCl<Stack><Subscript>4</Subscript><Superscript>−</Superscript></Stack> onto methyltrioctyl ammonium chloride–naphthalene and subsequent atomic absorption spectrometric determination

A sensitive, selective and simple preconcentration method for ultra-trace gold determination has been developed that uses naphthalene–methyltrioctyl ammonium chloride (Aliquat 336s) as an adsorbent. Gold, in the form of AuCl₄^–, was retained by the adsorbent in the column at a flow rate of 1 ml min^–1. After filtration, the solid mass consisting of the gold complex and naphthalene was dissolved out of the column with 5 ml of N,N-dimethylformamide (DMF), and the metal was then determined by atomic absorption spectrometry. In the initial solution, the calibration graph of absorbance versus gold concentration was found to be linear in the range 0.5–150 ng ml^–1 Au(III) with r=0.997 (n =9), and the 3 s detection limit was 0.428 ng ml^–1. The relative standard deviation for eight replicate measurements of 20 g of gold was 2.14%. Preconcentration factors of 390 and 650 were achieved using 5 ml and 3 ml of DMF, respectively. The proposed method was successfully applied to the determination of gold in wastewater, processed pool water, slurry pool water, and raw well-water from the Moteh gold mine, and synthetic samples.     

Assay of femtogram level nitrite in human urine using luminol–myoglobin chemiluminescence

In this paper, a sensitive flow injection chemiluminescence system luminol–myoglobin was described for determining femtogram nitrite. Nitrite bound myoglobin producing the ferric heme nitrite complexes, which catalyzed the electron transfer of luminol to myoglobin leading to fast chemiluminescence. The chemiluminescence intensity in the presence of nitrite was remarkably enhanced compared with that in the absence of it. Under the optimum reaction conditions the chemiluminescence increment produced was proportional to the concentration of nitrite in the range of 0.05 pg ml^− 1–1.0 ng ml^− 1 (R² = 0.9991), with a detection limit (3σ) of 20.0 fg ml^− 1. At the flow rate of 2.0 ml min^− 1, the whole process including sampling and washing could be completed in 0.5 min offering the sampling efficiency of 120 h^− 1 accordingly, and the relative standard deviation (RSD) was less than 2.60% (n = 5). It was satisfactory for the application to determine nitrite in human urine samples, and the possible mechanism was proposed.     

Determination of moxifloxacin in tablets and human urine by square-wave adsorptive voltammetry

This work presents an electroanalytical methodology developed for square-wave voltammetry based in the electrochemical reduction in hanging mercury drop electrode (HMDE), which is simple, fast, reliable and sensitive for determination of moxifloxacin (MOXI) in tablets and spiked urine human samples. The support electrolyte that provided a more defined and intense peak current for MOXI determination was the phosphate buffer 0.04 mol l^{− 1} pH 8.0. In the best-optimized conditions the drug presented an only peak of reduction at − 1.38 V vs. Ag/AgCl, using an E_acc. of − 0.30 V. An LOD of 0.44 and 3.20 ng ml^{− 1} and an LOQ of 1.46 and 10.60 ng ml^{− 1} were found for the pure standard of moxifloxacin and in the presence of matrix, respectively. A good recovery was obtained for assay spiked urine samples and a good quantification of MOXI was achieved in a commercial formulation. The methodology proposed was more sensitive than the spectrofluorimetric and spectrophotometric method with precision and accuracy equivalent.     

Simultaneous determination of chromium(VI) and chromium(III) by flame atomic absorption spectrometry with a chelating ion-exchange flow injection system

Summary Simultaneous Determination of Chromium(VI) and Chromium(III) by Flame Atomic Absorption Spectrometry with a Chelating Ion-Exchange Flow Injection System A simple method is described for the simultaneous determination of chromium(VI) and chromium(III) in a flow injection system comprising chelating ion-exchange and flame atomic absorption spectrometry. Sampling rates for 2001 and 1 ml sample volumes were 120 and 60 h^–1 (240 and 120 speciations per hour), respectively. Typical relative standard deviations were 0.52% for Cr(VI) (0.50g ml^–1 and 0.67% for Cr(III) (0.10,g ml^–1) and the corresponding limits of detection were 85 ng ml^–1, and 16 ng ml^–1, respectively.On leave from University of Belgrade.     

Electrochemical and DNA-binding properties of dipyridophenazine complexes of osmium(II)

A transition metal complex as an electrochemical probe of a DNA sensor must have an applicable redox potential, high binding affinity and chemical stability. Some complexes with the dipyrido[3,2-a:2′,3′-c]phenazine (DPPZ) ligand have been reported to have high binding affinity for DNA. However, it was difficult to detect the targeted DNA electrochemically using these complexes because of the relatively high redox potential. In this work, a combination of bipyridine ligands with functional groups (---NH₂, ---CH₃ and ---COOH) and the DPPZ ligand were studied. The introduction of electron-donating groups was effective for controlling the redox potential of the DPPZ-type osmium complex. The [Os(DA-bpy)₂DPPZ]²⁺ complex (DA-bpy; 4,4′-diamino-2,2′-bipyridine) had a lower half-wave potential (E_1/2) of 147 mV (vs. Ag AgCl) and higher binding affinity with DNA {binding constant, K=3.1×10⁷ M⁻¹ in 10 mmol dm⁻³ Tris–HCl buffer with 50 mmol dm⁻³ NaCl (pH 7.76)} than those of other complexes. With the single stranded DNA (ssDNA) modified gold electrode, the hybridization signal (ΔI) of the [Os(DA-bpy)₂DPPZ]²⁺ complex was linear in the concentration range of 1.0 pg ml⁻¹–0.12 μg ml⁻¹ for the targeted DNA with a regression coefficient of 0.999. The detection limit was 0.1 pg ml⁻¹.     

Influence of biomass and gold salt concentration on nanoparticle synthesis by the tropical marine yeast Yarrowia lipolytica NCIM 3589

Cell-associated gold nanoparticles and nanoplates were produced when varying number of Yarrowia lipolytica cells were incubated with different concentrations of chloroauric acid (HAuCl₄) at pH 4.5. With 10⁹ cells ml⁻¹ and 0.5 or 1.0 mM of the gold salt, the reaction mixtures developed a purple or golden red colour, respectively, and gold nanoparticles were synthesized. Nanoparticles of varying sizes were produced when 10¹⁰ cells ml⁻¹ were incubated with 0.5, 1.0 or 2.0 mM chloroauric acid salt. With 3.0, 4.0 or 5.0 mM HAuCl₄, nanoplates were also observed. With 10¹¹ cells ml⁻¹ nanoparticles were synthesized with almost all the gold salt concentrations. The cell-associated particles were released outside when nanoparticle-loaded cells were incubated at low temperature (20 °C) for 48 h. With increasing salt concentrations and a fixed number of cells, the size of the nanoparticles progressively increased. On the other hand, with increasing cell numbers and a constant gold salt concentration, the size of nanoparticles decreased. These results indicate that by varying the number of cells and the gold salt concentration, a variety of nanoparticles and nanoplates can be synthesized. Fourier transform infrared (FTIR) spectroscopy revealed the possible involvement of carboxyl, hydroxyl and amide groups on the cell surfaces in nanoparticle synthesis.     

Development of an integrated flow injection system for the electro-oxidative leaching of uranium from geological samples and its spectrophotometric determination with Arsenazo III

This work proposes a new procedure for on-line electro-oxidative leaching and spectrophotometric determination of uranium in ore samples. By associating a conventional flow injection system, used for uranium determination with Arsenazo III, with an on-line system for electro-oxidative leaching, a fully integrated system was assembled. The systems were integrated after achieving optimum conditions for uranium determination and leaching. According to the results obtained in the present work, a current density of 280 mA cm⁻² generated enough hypochlorite ions in the electrolyte solution (3.6 mol L⁻¹ HCl + 2% (w/v) NaCl) to promote quantitative oxidation of U(IV) to U(VI) thus improving the extraction efficiency. The slurry density did not significantly affect the performance of the system and the increasing temperature resulted in a decrease in extraction efficiency. This methodology was applied in the determination of U₃O₈ in four ore samples and the results obtained agreed with those obtained by ICP-MS after conventional wet acid digestion of the samples.     

流动注射在线吸附预富集-冷蒸气原子荧光法测定矿泉水中的痕量无机汞

研究了聚四氟乙烯管编结反应器(KR)在线吸附预富集技术与冷蒸气原子荧光联用测定矿泉水中痕量无机汞的方法.Hg2+与DDTC在线形成Hg2+-DDTC络合物并吸附在KR内壁上,采用电磁感应加热技术,用20% (V/V) HNO3在线加热洗脱并氧化预富集于KR内壁上的Hg2+-DDTC.洗脱液与KBH4溶液反应生成蒸气态汞,直接用冷蒸气原子荧光联用技术检测.20%(V/V)HNO3作为洗脱液的同时也为氢化发生提供了酸性介质.本方法未使用常用的有机洗脱液,具有操作简单和环保等优点.每小时可分析30个样品,最大吸附倍数为35倍,样品分析精密度RSD为2.2%(n=11),检出限(3σ)为2.0 ng/L.     

Spectral and fluorescent kinetics features of Nd3+ ion in Nb2O5, Ta2O5 and La2O3 mixed lithium zirconium silicate glasses

A sensitive competitive flow injection chemiluminescence (CL-FIA) immunoassay for immunoglobulin G (IgG) was developed using gold nanoparticle as CL label. In the configuration, anti-IgG antibody was immobilized on a glass capillary column surface by 3-(aminopropyl)-triethoxysilane and glutaraldehyde to form immunoaffinity column. Analyte IgG and gold nanoparticle labeled IgG were passed through the immunoaffinity column mounted in a flow system and competed for the surface-confined anti-IgG antibody. CL emission was generated from the reaction between luminol and hydrogen peroxide in the presence of Au (III), generated from chemically oxidative dissolution of gold nanoparticle by an injection of 0.10 mol L⁻¹ HCl–0.10 mol L⁻¹ NaCl solution containing 0.10 mmol L⁻¹ Br₂. The concentration of analyte IgG was inversely related to the amount of bound gold nanoparticle labeled IgG and the CL intensity was linear with the concentration of analyte IgG from 1.0 ng mL⁻¹ to 40 ng mL⁻¹ with a detection limit of 5.2 × 10⁻¹⁰ g mL⁻¹. The whole assay time including the injections and washing steps was only 30 min for one sample, which was competitive with CL immunoassays based on a gold nanoparticle label and magnetic separation. This work demonstrates that the CL immunoassay incorporation of nanoparticle label and flow injection is promising for clinical assay with sensitivity and high-speed.     

Determination of Cytochrome <Emphasis Type="Italic">c</Emphasis> in Human Serum and Pharmaceutical Injections Using Flow Injection Chemiluminescence

It was found that the complex of cytochrome c (Cyt c) and hydrogen peroxide could significantly catalyze the chemiluminescence (CL) reaction from luminol–hydrogen peroxide, and a sensitive, rapid, and simple CL procedure was proposed for the determination of Cyt c in a flow injection system for the first time. The increment of CL intensity was linear over the concentration of Cyt c ranging from 5 to 700 ng ml⁻¹, with a detection limit of 2 ng ml⁻¹ (3σ). At a flow rate of 2.0 ml min⁻¹, a complete analytical process could be performed in 30 s with a relative standard deviation of less than 4.0%. The proposed method was applied successfully for the assay of Cyt c in pharmaceutical injections and human serum, and the recoveries were from 98.0% to 108.8% and 92.5% to 109.0%. The possible mechanism of Cyt c enhanced CL reaction was also discussed.     

Spectrophotometric determination of microamounts of gold(III) with propericiazine

Propericiazine is proposed as a new reagent for the spectrophotometric determination of gold(III). The reagent forms an orange-red-colored species with gold(III) instantaneously in 4–8 M phosphoric acid. The orange-red species exhibits maximum absorbance at 511 nm. Beer's law is valid over the concentration range 0.1–7.0 μg/ml. The molar absorptivity is found to be 3.85 × 10⁴ liter mol⁻¹ cm⁻¹. The effects of acidity, time, order of addition of reagents, temperature, reagent concentration, and diverse ions are investigated.     

HPLC Method for Determination of Rosiglitazone in Plasma

A fast and sensitive high performance liquid chromatography method for quantitative determination of rosiglitazone in human plasma has been developed. The extraction from plasma was performed using solid-phase extraction (SPE) on C4 silica (100 mg) disposable extraction cartridges (DEC). The separation of rosiglitazone and two metabolites was achieved on a Phenomenex® Synergi 4 µm MAX-RP (150 × 4.6 mm) column, protected by a guard column. The mobile phase was 0.01 M ammonium acetate, pH 7.0 - acetonitrile (65:35, v/v). (3S)-3-OH-quinidine was used as internal standard. The analytes were detected using fluorescence detection. The method was validated. The limit of quantitation was 1 ng mL⁻¹ and the detection limit was 0.25 ng mL⁻¹ for rosiglitazone in human plasma. The recovery was 90% for rosiglitazone. Linearity was observed over a range of 1-1000 ng mL⁻¹ (r²=0.9959). The intra- and inter-day precision (C.V.) did not exceed 8.7 %. Applicability of the method was demonstrated by a clinical pharmacokinetic study. A healthy volunteer received in two separate phases 4 mg and 8 mg rosiglitazone maleate as a single oral dose. Plasma concentrations were measured for 24 h in both phases.     

Organically modified silica gel and flame atomic absorption spectrometry: employment for separation and preconcentration of nine trace heavy metals for their determination in natural aqueous systems

A 5-formyl-3-(1′-carboxyphenylazo) salicylic acid-bonded silica gel (FCPASASG) chelating adsorbent was synthesized according to a very simple and rapid one step reaction between aminopropyl silica gel (APSG) and 5-formyl-3-(1′-carboxyphenylazo) salicylic acid (FCPASA) and its adsorption characteristics were studied in details. Nine trace metals viz.: Cd(II), Zn(II), Fe(III), Cu(II), Pb(II), Mn(II), Cr(III), Co(II) and Ni(II) can be quantitatively adsorbed by the adsorbent from natural aqueous systems at pH 7.0–8.0. The adsorbed metal ions can be readily desorbed with 1 M HNO₃ or 0.05 M Na₂EDTA. The distribution coefficient, K_d and the percentage concentration of the investigated metal ions on the adsorbent at equilibrium, C_M,_eqm % (Recovery, R%) were studied as a function of experimental parameters. The logarithmic values of the distribution coefficient, logK_d, are 3.7–6.4. Some foreign ions caused little interference in the preconcentration and determination of the investigated nine metals by flame atomic absorption spectrometry (AAS).The adsorption capacity of FCPASASG was 0.32–0.43 meq g⁻¹. C and N elemental analyses of the adsorbent (FCPASASG) allowed us to calculate a surface converge of 0.82 mmol g⁻¹. This value compares well with the best values reported for the azo compounds. The adsorbent and its formed metal chelates were characterized by IR (absorbance and/or reflectance) and UV spectrometry, potentiometric titrations and thermogravimetric analysis (TGA and DTG). The mode of chelation between the FCPASASG adsorbent and the investigated metal ions is proposed to be due to reaction of those metal ions with the salicylic and/or the carboxyphenylazo chelation centers of the FCPASASG adsorbent. Nanogram concentrations (0.07–0.14 ng ml⁻¹) of Cd(II), Zn(II), Fe(III), Pb(II), Cr(III), Mn(II), Cu(II), Co(II) and Ni(II) can be determined reliably with a preconcentration factor of 100.     

Microdetermination of Proteins with the 1,10-Phenanthroline–H2O2–Cetyltrimethylammonium Bromide–Cu(II) Chemiluminescence System

Proteins can enhance the chemiluminescence (CL) intensity of the 1,10-phenanthroline–H₂O₂–cetyltrimethylammonium bromide (CTMAB)–Cu(II) system because unsaturated complexes of Cu(II) with protein have a much stronger catalytic effect on the CL reaction than does Cu(II). On this basis, a new flow injection analysis method for detection of some proteins was established. The method gives linear responses over two orders of magnitude and detection limits at the 0.02–0.05 μg ml⁻¹level for bovine serum albumin, human serum albumin, γ-globulin, and egg albumin. The method was used for determination of proteins in human serum with satisfactory results.