Novel Complex Catalyst of η3‐(Pentamethylcyclopentadienyl)dimethylaluminum/Titanium(IV) Butoxide (Cp*AlMe2/Ti(OBu)4) for Syndiotactic Polystyrene

A novel metallocene catalyst was prepared from the reaction of (η³‐pentamethylcyclopentadienyl)dimethylaluminum (Cp*AlMe₂) and titanium(IV) n‐butoxide Ti(OBu)₄. The resulting titanocene Cp*Ti(OBu)₃ was combined with methylaluminoxane (MAO)/tri‐iso‐butylaluminum (TIBA) to carry out the syndiotactic polymerization of styrene. The resulting syndiotactic polystyrene (sPS) possesses high syndiotacticity according to ¹³C NMR. Catalytic activity and the molecular weight of the resulting sPSs were discussed in terms of reaction temperature, concentration of MAO, amounts of scavenger TIBA added, and the hydrogen pressure applied during polymerization.     

Oxidation of Stereo‐regular Poly(styrene‐co‐4‐methylstyrene) by Cobalt(II) Acetate Tetrahydrate/Sodium Bromide Catalyst

Chemical modification on the stereo‐regular poly(styrene‐co‐4‐methylstyrene) (sPS‐PMS) was attempted in this study. Metallocene copolymerization of styrene (St) and 4‐methylstyrene (MSt) was performed by using η⁵‐pentamethylcyclopentadienyl‐titanium(IV)tributoxide (Cp*Ti(OBu)₃)/methylaluminoxane (MAO)/tri‐iso‐butylaluminum (TIBA) catalyst in the bulk state. Cobalt(II) catalyst was then applied to oxidize the benzylic methyl group on the MSt units of the resulting sPS‐PMS copolymer. Both aldehyde and carboxylic acid in the oxidized products were resolved by the FTIR and ¹H NMR. The oxidized sPS‐PMSs exhibit a low and a high‐temperature T_g and T_m corresponding to the transitions in the amorphous and the crystalline regions. Hydrogen‐bond and polar interactions between the aldehyde and carboxylic acids tend to interrupt the regular chain packing of the oxidized sPS‐PMS, resulting in the lowering of T_m with oxidation level. The oxidized sPS‐PMS showed better adhesion to glass fiber than pure sPS‐PMS copolymer as evaluated from the respective SEM fractured micrographs.     

Syndiospecific polymerization of styrene with embedded metallocene catalysts

Syndiotactic polystyrene (sPS) is a highly crystalline polymer with high melting point (270°C). The syndiospecific polymerization of styrene to sPS with metallocene catalysts is characterized by significant phase changes that lead to global gelation. Since sPS does not dissolve in styrene or solvents such as toluene and n-heptane, sPS precipitates out immediately from the liquid phase with the start of polymerization. The polymer crystallites aggregate to primary particles and they develop to a gel. The gelation is not due to cross-linking polymerization but due to strong molecular interactions between the polymer and monomer molecules. In this work, homogeneous Cp*Ti(OMe)₃ catalyst is heterogenized or embedded into sPS prepolymer particles. The embedded catalyst has been tested in a laboratory scale diluent slurry process to illustrate the feasibility of slurry phase polymerization for the synthesis of sPS particles.     

Control of molecular weight in polymerization of vinyl chloride with Cp*Ti(OPh)3/MAO catalyst

Polymerization of vinyl chloride (VC) with titanium complexes containing Ti‐OPh bond in combination with methylaluminoxane (MAO) catalysts was investigated. Among the titanium complexes examined, Cp*Ti(OPh)₃/MAO catalyst (Cp*; pentamethylcyclopentadienyl, Ph; C₆H₅) gave the highest activity for the polymerization of VC, but the polymerization rate was slow. From the kinetic study on the polymerization of VC with Cp*Ti(OPh)₃/MAO catalyst, the relationship between the M_n of the polymer and the polymer yields gave a straight line, and the line passed through the origin. The M_w/M_n values of the polymer gradually decrease as a function of polymer yields, but the M_w/M_n values were somewhat broad. This may be explained by a slow initiation in the polymerization of VC with Cp*Ti(OPh)₃/MAO catalyst. The results obtained in this study demonstrate that the molecular weight control of the polymers is possible in the polymerization of VC with the Cp*Ti(OPh)₃/MAO catalyst. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3872–3876, 2007     

Novel catalyst compositions for the syndiospecific polymerization of styrene prepared by the combination of cyclopentadenyl complexes of group IIA or group IIIA elements with titanium alkoxides

A highly reactive catalyst system, which induces the syndiospecific polymerization of styrene with high activity, has been found by the combination of cyclopentadienyl (Cp) complexes of group IIA or group IIIA elements with titanium alkoxides. The ¹H NMR monitoring of these reactions reveals the occurrence of a novel Cp‐transfer reaction that leads to the generation of Cp‐containing titanium complexes as catalysts for promoting the syndiospecific polymerization of styrene. Detailed in situ ¹H NMR studies reveal that the rate of the Cp‐transfer reaction is highly dependent on the steric bulkiness of the titanium alkoxide complexes, the structures of the Cp complexes of group IIA or group IIIA elements, and the polymerization temperature. Styrene polymerization studies also reveal that a more effective Cp‐transfer reaction can typically lead to the generation of a more highly reactive catalyst for sPS polymerization. This study provides a convenient method for the in situ generation of variable structures of Cp/titanium alkoxide complexes, which are difficult to synthesize by other methods. Most importantly, the mixture of a catalyst precursor can be directly used as an sPS polymerization catalyst without isolation and purification of Cp/titanium complexes. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2304–2315, 2005     

Comparison of Syndiotactic Polystyrene Morphology Obtained Via Heterogeneous and Homogeneous Polymerization with Metallocene Catalyst

Summary: Supported catalyst system for the slurry phase polymerization of styrene in toluene was prepared by the immobilization of 2-methylindenyltrichlorotitanium(2-MeIndTiCl₃) on silica and activation of this catalyst was performed by methylaluminoxane(MAO) in polymerization media. Homogeneous polymerization of styrene with 2-methylindenyltrichlorotitanium activated by MAO was performed in toluene. The morphology of obtained syndiotactic polystyrene (sPS) via heterogeneous and homhgeneous catalyst system was compared. Polymerization of styrene by homogeneous catalyst lead to formation of gel and resultant polymers presented a compact and dense texture while the global gelation do not occur with silica supported catalyst at different Ti/SiO₂ mol ratios and sPS was obtained as separated particles. Unlike to the homogeneous catalyst, obtained polymers showed a porous texture. Highly porous texture of sPS was obtained with Ti/SiO₂ = 0.5% mol ratio.     

Polymerization of vinyl chloride with half‐titanocene/methylaluminoxane catalysts

The polymerization of vinyl chloride (VC) with half‐titanocene /methylaluminoxane (MAO) catalysts is investigated. The polymerization of VC with the Cp*Ti(OCH₃)₃/MAO catalyst (Cp* = η⁵‐pentamethylcyclopentadienyl) afforded high‐molecular‐weight poly(vinyl chloride) (PVC) in good yields, although the polymerization proceeded at a slow rate. With the Cp*TiCl₃/MAO catalyst, the polymer was also obtained, but the polymer yield was lower than that with the Cp*Ti(OCH₃)₃/MAO catalyst. The polymerization of VC with the Cp*Ti(OCH₃)₃/MAO catalyst was influenced by the MAO/Ti mole ratio and reaction temperature, and the optimum was observed at the MAO/Ti mole ratio of about 10. The optimum reaction temperature of VC with the Cp*Ti(OCH₃)₃/MAO catalyst was around 20 °C. The stereoregularity of PVC obtained with the Cp*Ti(OCH₃)₃/MAO catalyst was different from that obtained with azobisisobutyronitrile, but highly stereoregular PVC could not be synthesized. From the elemental analyses, the ¹H and ¹³C NMR spectra of the polymers, and the analysis of the reduction product from PVC to polyethylene, the polymer obtained with Cp*Ti(OCH₃)₃/MAO catalyst consisted of only regular head‐to‐tail units without any anomalous structure, whereas the Cp*TiCl₃/MAO catalyst gave the PVC‐bearing anomalous units. The polymerization of VC with the Cp*Ti(OCH₃)₃/MAO catalyst did not inhibit even in the presence of radical inhibitors such as 2,2,6,6,‐tetrametylpiperidine‐1‐oxyl, indicating that the polymerization of VC did not proceed via a radical mechanism. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 248–256, 2003     

单茂钛催化剂的苯乙烯间规聚合和乙烯聚合的比较

考察三甲基铝（ＴＭＡ） 部分水解法制备固体改性甲基铝氧烷（ｍ ＭＡＯ） 时,反应物Ｈ２Ｏ 和ＴＭＡ 的摩尔比对ｍ ＭＡＯ 的产量及ｍ ＭＡＯ 中ＴＭＡ 含量的影响;以五甲基茂基三苄氧基钛［Ｃｐ ＊ Ｔｉ（ＯＢｚ）３］／ｍ ＭＡＯ 组成的均相催化体系,分别考察ｍ ＭＡＯ 的用量［ 即Ａｌ／Ｔｉ 摩尔比］ 及ｍ ＭＡＯ 中ＴＭＡ 含量对苯乙烯间规聚合和乙烯聚合的影响．通过分析Ｃｐ ＊ Ｔｉ（ＯＢｚ）３／ｍ ＭＡＯ 催化体系钛氧化态的分布,发现Ｔｉ（ Ⅲ） 活性中心有利于合成间规聚苯乙烯;而Ｔｉ（ Ⅳ） 活性中心有利于合成聚乙烯．苯乙烯间规聚合时,外加三异丁基铝（ＴＩＢＡ） ,将提高催化活性,同时可节省ＭＡＯ 用量．     

(η5-Pentamethylcyclopentadienyl)trimethyltitanium as a precursor for the syndiospecific polymerization of styrene

An equimolar mixture of Cp*Ti(CH₃)₃ (2) and Ph₃C⁺[B(C₆F₅)₄]^? (1) forms a highly active and syndioselective catalyst for the polymerization of styrene, producing 96% syndiotactic polystyrene (PS) at an activity of 0.91 × 10⁷ g PS (mol Ti)^?1 (mol styrene)^?1 h^?1. Both activity and syndioselectivity can be increased using tri–isobutylaluminum (TIBA) to scavenge the system. ESR measurements indicate that the polymerization proceeds via titanium(IV) intermediates. Catalysts derived from 2/methylaluminoxane (MAO) as well as Cp*TiCl₃/MAO also function as syndioselective styrene polymerization catalysts, but are less active than the ‘cationic’; system derived from 1 and 2.     

Stereospecific styrene polymerization and ethylene–styrene copolymerization with titanocenes containing a pendant amine donor

A series of monocyclopentadienyl titanium complexes containing a pendant amine donor on a Cp group ( A = CpTiCl₃, B = Cp^NTiCl₃, C = Cp^NTiCl₂TEMPO, for Cp = C₅H₅, Cp^N = C₅H₄CH₂CH₂N(CH₃)₂, and TEMPO = 2,2,6,6‐tetramethylpiperidine‐N‐oxyl) are investigated for styrene homopolymerization and ethylene–styrene (ES) copolymerization. When activated by methylaluminoxane at 70 °C, complexes with the amine group ( B and C ) are active for styrene homopolymerization and afford syndiotactic polystyrene (sPS). The copolymerizations of ethylene and styrene with B and C yield high‐molecular weight ES copolymer, whereas complex A yields mixtures of sPS and polyethylene, revealing the critical role that the pendant amine has on the polymerization behavior of the complexes. Fractionation, NMR, and DSC analyses of the ES copolymers generated from B and C suggest that they contain sPS. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1579–1585, 2010     

The syndiospecific polymerization of styrene in the presence of fluorine‐containing half‐sandwich metallocenes

The syndiospecific polymerization of styrene was investigated with the fluorine‐containing half‐sandwich complexes η⁵‐pentamethylcyclopentadienyl titanium bis(trifluoroacetate) dimer, η⁵‐octahydrofluorenyl titanium tristrifluoro‐acetate, η⁵‐octahydrofluorenyl titanium dimethoxymonotrifluoroacetate, and η⁵‐octahydrofluorenyl titanium tris(pentafluorobenzoate) in comparison to known chloride and methoxide complexes in the presence of relatively low amounts of methylalumoxane and triisobutylaluminum. After the selection of effective reaction conditions for a solvent‐free polymerization, the following orders of decreasing polymerization activity of the titanium complexes can be observed: for pentamethylcyclopentadienyl compounds, Cp*Ti(OMe)₃ > [Cp*Ti(OCOCF₃)₂]₂O ≈ Cp*TiCl₃, and for octahydrofluorenyl compounds, [656]Ti(OMe)₃ > [656]Ti(OCOC₆F₅)₃ > [656]Ti(OCH₃)₂(OCOCF₃) > [656]Ti (OCOCF₃)₃. The [656]Ti complexes, showing the highest polymerization conversions at 70 °C and in comparison with the Cp* Ti compounds, turned out to be highly efficient catalysts for the syndiospecific styrene polymerization. The fluorine‐containing Cp* and [656]Ti complexes lead to much higher molecular weights than the chloride and methoxide compounds because of a reduction in chain‐limiting transfer reactions. The introduction of only one fluorine‐containing ligand into the coordination sphere of the metal compound is obviously sufficient for a significant increase in molecular weight. The active polymerization sites of the [656]Ti complexes with methylalumoxane and triisobutylaluminum are extremely stable during storage at room temperature in regard to their polymerization activity. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2428–2439, 2000     

C-NMR study of Ti(IV) species formed by Cp*TiMe3 and Cp*TiCl3 activation with methylaluminoxane (MAO)

Using ¹³C- and ¹H-NMR spectroscopy, titanium(IV) species formed in the catalytic systems Cp*TiMe₃/MAO and Cp*TiCl₃/MAO (Cp*=C₅(CH₃)₅) in toluene and chlorobenzene were studied within the temperature range 253-293 K and at Al/Ti ratios 30-300. It was shown that upon activation of Cp*TiMe₃ with methylaluminoxane (MAO) mainly the ‘cation-like’ intermediate Cp*Me₂Ti⁺←Me⁻Al(MAO) (2) is formed. Three types of titanium(IV) complexes were identified in Cp*TiCl₃/MAO catalytic system. They are methylated complexes Cp*TiMeCl₂ and Cp*TiMe₂Cl, and the ‘cation-like’ intermediate 2. Complex 2 dominates in Cp*TiCl₃/MAO system in conditions approaching to those of practical polymerization (Al/Ti ratios more than 200). According to the EPR measurements, the portion of EPR active Ti(III) species in the Cp*TiCl₃/MAO system is smaller than 1% at Al/Ti=35, and is about 10% at Al/Ti=700.     

Syntheses and characterizations of polypropene,polystyrene and their block copolymers with titanocene catalysts

Pentamethylcyclopentadienyltitanium tribenzyloxide, Cp^*Ti(OBz)₃, was used as the catalyst precursor for polymerizations of propene and styrene. The titanocene catalyst affords atactic polypropene and syndiotactic polystyrene with high activities in the presence of methylalumimoxane (MAO). Block copolymerization of propene and styrene was carried out in the presence of Cp^*Ti(OBz)₃/MAO catalyst system by the means of external addition of triisobutylaluminum (TIBA) and sequential monomer feed. The copolymerization product is mainly a mixture of atactic polypropene(aPP) and syndiotactic polystyrene(sPS) homopolymers and aPP-b-sPS block copolymers, which can be separated into fractions with successive extraction with boiling methylethyl ketone(MEK), heptane, tetrahydrofuran(THF), and chloroform. Studies on thermal properties showed that rubbery phases and crystalline regions both appear in the block copolymer at the room temperature and that aPP-b-sPS block copolymer has better toughness than sPS.     

Silica Nanotube Reactors for Catalytic Polymerization of Styrene and Olefins

Summary: Silica nanotube reactor (SNTR) has been designed and used as a novel catalytic polymerization reactor device to synthesize syndiotactic polystyrene (sPS), and polyethylene with Cp*Ti(OCH₃)₃ and rac-Et(indenyl)₂ZrCl₂ metallocene catalysts in conjunction with methylaluminoxane (MAO). The highly crystalline sPS molecules polymerized within the SNTR form nano-scale polymeric fibrils of 30–50 nm in diameter that further intertwine to fill the nanopore. The polymer molecular weight of sPS has been found to increase significantly in the SNTR. A simplified mathematical reaction model for the SNTR suggests that hindered chain transfer reactions in the nanopores filled with rigid polymeric nanofibrils might have caused the extended polymer chain length. The morphological characteristics of polymeric nanofibrils and the effect of SNTR's geometric confinement on the polymer properties are also discussed. It is also demonstrated that the liberated SNTR can be a novel ‘See-Through’ tool for visual observation when it is analyzed by transmission electron microscopy.     

Synthesis of high‐molecular‐weight elastomeric poly(propylene) with half‐titanocene/MAO catalyst

A novel catalyst precursor, (η⁵‐pentamethylcyclopentadienyl)titanium triallyloxide (Cp*Ti(OCH₂—CH=CH₂)₃), was prepared and employed in a study of propylene polymerization in the presence of methylaluminoxane (MAO). This work has revealed that the half‐titanocene catalyst is desirable for the production of elastomeric poly(propylene) with high molecular weight (M_w = 8–69×10⁴) as well as in good yields under typical polymerization conditions.     

Zur Reaktivität von Titanocenkomplexen [Ti(Cp′)2(η2‐Me3SiC≡CSiMe3)] (Cp′ = Cp,Cp*) gegenüber Benzoldicarbonsäuren

On the Reactivity of Titanocene Complexes [Ti(Cp′)₂(η²‐Me₃SiC≡CSiMe₃)] (Cp′ = Cp, Cp*) towards Benzenedicarboxylic Acids Titanocene complexes [Ti(Cp′)₂(BTMSA)] ( 1a , Cp′ = Cp = η⁵‐C₅H₅; 1b , Cp′ = Cp* = η⁵‐C₅Me₅; BTMSA = Me₃SiC≡CSiMe₃) were found to react with iodine and methyl iodide yielding [Ti(Cp′)₂(μ‐I)₂] ( 2a / b ; a refers to Cp′ = Cp and b to Cp′ = Cp*), [Ti(Cp′)₂I₂] ( 3a / b ) and [Ti(Cp′)₂(Me)I] ( 4a / b ), respectively. In contrast to 2a , complex 2b proved to be highly moisture sensitive yielding with cleavage of HCp* [{Ti(Cp*)I}₂(μ‐O)] ( 7 ). The corresponding reactions of 1a / b with p‐cresol and thiophenol resulted in the formation of [Ti(Cp′)₂{O(p‐Tol)}₂] ( 5a / b ) and [Ti(Cp′)₂(SPh)₂] ( 6a / b ), respectively. Reactions of 1a and 1b with 1,n‐benzenedicarboxylic acids (n = 2–4) resulted in the formation of dinuclear titanium(III) complexes of the type [{Ti(Cp′)₂}₂{μ‐1,n‐(O₂C)₂C₆H₄}] (n = 2, 8a / b ; n = 3, 9a / b ; n = 4, 10a / b ). All complexes were fully characterized analytically and spectroscopically. Furthermore, complexes 7 , 8b , 9a ·THF, 10a / b were also be characterized by single‐crystal X‐ray diffraction analyses.     

Sterically Less‐Hindered Half‐Titanocene(IV) Phenoxides: Ancillary‐Ligand Effect on Mono‐, Bis‐, and Tris(2‐Alkyl‐/arylphenoxy) Titanium(IV) Chloride Complexes

A series of mono‐, bis‐, and tris(phenoxy)–titanium(IV) chlorides of the type [Cp*Ti(2‐R? PhO)_nCl_3?n] (n=1–3; Cp*=pentamethylcyclopentadienyl) was prepared, in which R=Me, iPr, tBu, and Ph. The formation of each mono‐, bis‐, and tris(2‐alkyl‐/arylphenoxy) series was authenticated by structural studies on representative examples of the phenyl series including [Cp*Ti(2‐Ph? PhO)Cl₂] ( 1 PhCl2 ), [Cp*Ti(2‐Ph? PhO)₂Cl] ( 2 PhCl ), and [Cp*Ti(2‐Ph? PhO)₃] ( 3 Ph ). The metal‐coordination geometry of each compound is best described as pseudotetrahedral with the Cp* ring and the 2‐Ph? PhO and chloride ligands occupying three leg positions in a piano‐stool geometry. The mean Ti? O distances, observed with an increasing number of 2‐Ph? PhO groups, are 1.784(3), 1.802(4), and 1.799(3) Å for 1 PhCl2 , 2 PhCl , and 3 Ph , respectively. All four alkyl/aryl series with Me, iPr, tBu, and Ph substituents were tested for ethylene homopolymerization after activation with Ph₃C⁺[B(C₆F₅)₄]^? and modified methyaluminoxane (7% aluminum in isopar E; mMAO‐7) at 140 °C. The phenyl series showed much higher catalytic activity, which ranged from 43.2 and 65.4 kg (mmol of Ti?h)^?1, than the Me, iPr, and tBu series (19.2 and 36.6 kg (mmol of Ti?h)^?1). Among the phenyl series, the bis(phenoxide) complex of 2 PhCl showed the highest activity of 65.4 kg (mmol of Ti?h)^?1. Therefore, the catalyst precursors of the phenyl series were examined by treating them with a variety of alkylating reagents, such as trimethylaluminum (TMA), triisobutylaluminum (TIBA), and methylaluminoxane (MAO). In all cases, 2 PhCl produced the most catalytically active alkylated species, [Cp*Ti(2‐Ph? PhO)MeCl]. This enhancement was further supported by DFT calculations based on the simplified model with TMA.     

To Coordinate or not to Coordinate: The Special Role of Chalcogen Ether Functionalities in the Design of Twofold Functionalized Cyclopentadienyl Ligands [Cp,O,Ch (Ch = S,Se)]

The solvent‐ and catalyst free synthesis of two β‐thio ketones L1a and L1b is reported. L1a , L1b , and a β‐seleno ketone L1c were successfully employed as ligand precursors in the synthesis of a novel series of cationic titanium complexes 4a – 4c via a well‐established reaction sequence: insertion of the carbonyl functional group into the polarized Ti–C_q,exo bond of the monopentafulvene complex Cp*Ti(Cl)(π‐η⁵:σ–η¹‐C₅H₄=CR₂) ( 1 ) (CR₂ = adamantylidene), subsequent methylation, and final activation with B(C₆F₅)₃. The cationic titanium complexes 4a – 4c bear twofold functionalized cyclopentadienyl [Cp,O,Ch (Ch = S, Se)] ligand frameworks built directly in the coordination sphere of the metal, in which the chalcogen ether functionalities do not coordinate to the central metal atoms as demonstrated by NMR experiments. Consequently, Cp,O σ,π chelating ligand systems are formed with free coordination sites at the central titanium atoms and pendant chalcogen ether moieties.     

Preparation and characterization of some structural variants of Cp*Ti(1,2-propandiolato) complexes

1,2-Propandiol reacts with Cp*Ti(CH₃)₃ by rapid liberation of methane to yield a dimetallic complex 6 of the net composition (Cp*Ti)₂(1,2-propandiolato)₃. The X-ray crystal structure analysis revealed an unsymmetrical bridging between the [Cp*Ti(1,2-propandiolato)] and [Cp*Ti(1,2-propandiolato)₂] subunits. Cp*TiCl₃ reacts with 1,2-propandiol in a 1:1 stoichiometry in the presence of excess pyridine by replacement of two chlorides by a 1,2-propandiolato ligand. The resulting product was isolated as a dimer 8 and characterized by X-ray diffraction. It exhibits a central Ti₂O₂ ring that was formed by bridging between the two [Cp*TiCl(1,2-propandiolato)] subunits using the oxygen atoms of the primary end of the ligand. From the reaction mixture a more complicated condensation product 9 was isolated in a small yield that contains two [Cp*TiCl(1,2-propandiolato)] units connected in a similar way by a Cp*-free [Ti(1,2-propandiolato)₂] moiety as revealed by its X-ray crystal structure analysis. Complex [Cp*TiCl(1,2-propandiolato)]₂ (8) gives an active catalyst for the syndiotactic polymerization of styrene upon treatment with excess methylalumoxane in toluene solution.     

Copolymerization behavior of titanium imidazolin‐2‐iminato complexes

Monocyclopentadienyl titanium imidazolin‐2‐iminato complexes [Cp′Ti(L)X₂] 1a (Cp′ = cyclopentadienyl, L = 1,3‐di‐tert‐butylimidazolin‐2‐imide, X = Cl), 1b (X = CH₃); 2 (Cp′ = cyclopentadienyl, L = 1,3‐diisopropylimidazolin‐2‐imide, X = Cl); 3 (Cp′ = tert‐butylcyclopentadienyl, L = 1,3‐di‐tert‐butylimidazolin‐2‐imide, X = Cl), upon activation with methylaluminoxane (MAO) were active for the polymerization of ethylene and propylene and the copolymerization of ethylene and 1‐hexene. Catalysts derived from imidazolin‐2‐iminato tropidinyl titanium complex 4 = [(Trop)Ti(L)Cl₂] (Trop = tropidinyl, L = 1,3‐di‐tert‐butylimidazolin‐2‐imide) were much less active. Narrow polydispersities were observed for ethylene and propylene polymerization, but the copolymerization of ethylene/hexene led to bimodal molecular weight distributions. The productivity of catalysts derived from the dialkyl complex 1b activated with [Ph₃C][B(C₆F₅)₄] or B(C₆F₅)₃ were less active for ethylene/hexene copolymerization but yielded ethylene/hexene copolymers of narrower molecular weight distributions than those derived from 1a/MAO. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 6064–6070, 2008