Miscibility studies on blends of polycarbonate with syndiotactic polymethyl methacrylate

Miscibility of bisphenol-A polycarbonate (PC) and syndiotactic polymethyle methacrylate (sPMMA) blends was investigated by differential scanning calorimetry (DSC) and small-angle light scattering. Cloud-point measurements indicated the existence of both a lower critical solution temperature and an upper critical solution temperature, forming an immiscibility loop. This immiscibility gap was observed for PC blends with sPMMA of various molecular weights ranging from 8,300 to 55,000. The DSC study on solvent-cast and coprecipitated PC/sPMMA blends from tetrahydrofuran solutions showed a single glass transition, shifting regularly with composition. The annealing of the 50/50 composition within the immiscibility loop exhibited dual glass transitions, but the system reverted to a single phase upon annealing above the loop. Phase dissolution took place during annealing above the loop, followed by thermoxidative branching (cross-linking) reaction. Dry pellets of PC and sPMMA were melt mixed above the loop in a Mini-Max mixer/molder; these molded blends exhibited a single phase. © 1993 John Wiley & Sons, Inc.     

Poly(ε-caprolactone) + unsaturated isophtalic polyester blends: Thermal properties and morphology

Miscibility of blends composed by a linear unsaturated polyester (LUP) with poly(ε-caprolactone) (PCL) of different molecular weights (M_w = 50 × 10³, 18 × 10³ and 2 × 10³) has been studied. The blends were subjected to different thermal treatments and have been studied by FT-IR spectroscopy, differential scanning calorimetry (DSC) and scanning electronic microscopy (ESEM). FT-IR results allow proving the miscibility of the blends at temperatures above the melting temperature of neat PCL. DSC measurements confirm the existence of a crystalline phase corresponding to neat PCL. The crystallization of PCL is observed in a wide range of blends composition, being detected in all the blend compositions when the crystallization time increases. Thermograms show clearly the glass transition temperatures of samples that have been rapidly quenched from the melt. However, the change in the heat flow corresponding to the glass transition temperatures is difficult to detect in samples with high PCL crystallization degree. The analysis of the results indicates that the morphology of the amorphous phase is heterogeneous for LUP + PCL blends and changes depending on the thermal treatment. The ESEM measurements, confirm the heterogeneity of the amorphous phase. The decrease of the molecular weight of the PCL favours the miscibility of the blends.     

Miscibility Behaviour of Poly(ether Sulphone)/nylon-6 Blends

Binary blends of poly (ether sulphone) (PES) and Nylon-6 were prepared in a whole range of composition by melt extrusion. Miscibility behaviour of the blends were studied using thermal analytical techniques like differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). Due to the rapid crystallization of Nylon-6 as it is cooled from the melt state, its glass transition behaviour could not be detected even in the quenched samples by DSC. Furthermore, the crystallization and melting behaviour of the blends have been studied by DSC. DMA results show that the dynamic storage modulus of the blends were in-between those of the constituent polymers. Also the glass transition of Nylon-6 phase as determined by the peak in loss tangent remains constant which shows that the two polymers are immiscible. Thermal expansion coefficient of the blends as determined by TMA is greater than that of Nylon-6 signifying the increased dimensional stability of the blends at higher temperatures. Morphological studies done by scanning electron microscopy (SEM) show the biphasic nature of the blends, with clear cut boundaries between the phases because of poor interfacial adhesion. Dispersed particle size is small when Nylon-6 is the dispersed phase because of its lower melt viscosity as compared to PES. Thermal stability of the blends was measured using thermogravimetric analysis (TG). Two-step decomposition behaviour was observed because of macro-phase separated morphology. This revised version was published online in July 2006 with corrections to the Cover Date.     

Mixtures poly((<Emphasis Type="Italic">R</Emphasis>)-3-hydroxybutyrate) and poly(<Emphasis Type="SmallCaps">l</Emphasis>-lactic acid) subjected to DSC

Blends of bacterial poly((R)-3-hydroxybutyrate) (PHB) and poly(l-lactic acid) (PLLA) synthesized by polycondensation of l-lactic acid or by ring-opening polymerization of l-lactide were studied. Miscibility was investigated through both conventional differential scanning calorimetry (DSC) and temperature-modulated DSC (TMDSC). PHB and low-molar mass PLLA were miscible in a whole concentration range, and a single glass transition temperature was observed. On the other hand, PHB/high-molar mass PLLA mixtures phase separate, giving rise to two glass transition temperatures corresponding to PHB and PLLA. A treatment of blends at 190 °C leads to formation of block/multiblock/random copolymers, and blends become miscible.     

Kinetics of relaxation and unmixing in polymer blends as studied by x-ray scattering

Concentration fluctuations in polystyrene/poly(styrene-co-bromostyrene) blends and changes induced by temperature jumps were studied by small-angle X-ray scattering. Structure factors in thermal equilibrium show the form given by the random phase approximation. Kinetics of structure changes after T-jumps within the homogeneous phase or jumps from the mixed state into the two-phase region are in accordance with the predictions of latest theories, being described by a simple equation of motion. Application of the theory enables a determination of relaxation times dependent upon the wave vectors. At temperatures near to the glass transition, relaxation and growth become nonexponential.     

Epoxy/poly(benzyl methacrylate) blends: miscibility, phase separation on curing and morphology

Diglycidyl ether of bisfenol-A (DGEBA)/polybenzyl methacrylate (PBzMA) blends cured with 4,4’-diaminodiphenylmethane (DDM) were studied. Miscibility, phase separation, cure kinetics and morphology were investigated through differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). Non-reactive DGEBA/PBzMA blends are miscible over the whole composition range. The addition of PBzMA to the reactive (DGEBA+DDM) mixture slows down the curing rate, although the reaction mechanism remains autocatalytic. On curing, initially miscible (DGEBA+DDM)/PBzMA blends phase separate, arising two glass transition temperatures that correspond to a PBzMA-rich phase and to epoxy network. Cured epoxy/PBzMA blends present different morphologies as a function of the PBzMA content.     

Influence of chain architecture on phase behaviour of styrene-(styrene/butadiene)-styrene triblock copolymers and their binary blends

The phase behaviour of symmetric (LN4) and asymmetric (LN3) triblock copolymers based on styrene-b-(styrene-co-butadiene)-b-styrene (S-SB-S) and their blends have been studied using transmission electron microscopy (TEM) and small-angle X-ray scattering (SAXS) and were correlated with rheological properties. A direct control over the final morphology and segregation strength for the block copolymer blends was achieved by blending of LN3 and LN4. The interaction parameter (χ) for LN4 is extracted by fitting the SAXS patterns at temperatures well above the ODT in consistency with Leibler mean-field structure-function for ABA triblock copolymers. A weak temperature dependency of χ has been observed which revealed that the phase behaviour in LN4 is mainly controlled by the entropic term. In the low frequency regime a non-terminal flow behaviour was observed in LN3 revealing the persistence of ordered structure within the experimental temperature range whereas a terminal flow behaviour with composition fluctuation was observed in LN4. G′ vs. G″ plots indicated a solid-like elastic melt behaviour for LN3 whereas presence of ODT over a broad temperature range was observed for LN4. ODT is observed to increase non-linearly with increase in LN3 content in the blends. ODT behaviour of the blends further reveals that the blends shift from weak-segregation to intermediate-segregation strength with the increase in LN3 content. The improvement in the state of ordering along with the change in morphology with the increase of LN3 content is attributed to co-surfactant effect between the PS end-blocks of LN3 and LN4 inside PS-rich phase.     

Miscibility and compatibilization of poly(trimethylene terephthalate)/acrylonitrile-butadiene-styrene blends

Poly(trimethylene terephthalate)/acrylonitrile-butadiene-styrene (PTT/ABS) blends were prepared by melt processing with and without epoxy or styrene-butadiene-maleic anhydride copolymer (SBM) as a reactive compatibilizer. The miscibility and compatibilization of the PTT/ABS blends were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), capillary rheometer and scanning electron microscopy (SEM). The existence of two separate composition-dependent glass transition temperatures (T_gs) indicates that PTT is partially miscible with ABS over the entire composition range. In the presence of the compatibilizer, both the cold crystallization and glass transition temperatures of the PTT phase shifted to higher temperatures, indicating their compatibilization effects on the blends.The PTT/ABS blends exhibited typical pseudoplastic flow behavior. The rheological behavior of the epoxy compatibilized PTT/ABS blends showed an epoxy content-dependence. In contrast, when the SBM content was increased from 1 wt% to 5 wt%, the shear viscosities of the PTT/ABS blends increased and exhibited much clearer shear thinning behavior at higher shear rates. The SEM micrographs of the epoxy or SBM compatibilized PTT/ABS blends showed a finer morphology and better adhesion between the phases.     

Effect of aromatic substitution on phase behavior of blends of halogenated polystyrene and conventional polystyrene

Miscibility phase behavior in blends of poly(bromostyrene) with polystyrene (PS) has been investigated by means of time‐resolved light scattering, optical microscopy, and DSC. Cloud point phase diagrams of blends of conventional PS with poly‐(2‐bromostyrene) (P2BrS), poly‐(3‐bromostyrene), and poly‐(4‐bromostyrene) of comparable molecular weights were established by light scattering. Of particular interest is the fact that ortho, meta, and para substitutions in the styrenic aromatic rings of poly(bromostyrene) show profound effects on the composition–temperature phase diagrams of their blends with PS, exhibiting a lower critical‐solution temperature (LCST), an upper critical solution temperature (UCST), and combined LCST/UCST diagrams, respectively. Poly‐(2‐chlorostyrene) exhibits an LCST behavior very close to that of the P2BrS blend, suggesting that these types of halogen atoms may be inconsequential to phase behavior. A similar study has been extended to a PS blend containing commercial brominated PS (66 mol % bromine substitution) to determine what location of bromine substitution is crucial for miscibility enhancement in the flame‐retardant brominated PS blends. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1605–1615, 2001     

Wormlike micelle formation and flow alignment of a pluronic block copolymer in aqueous solution

The self-assembly into wormlike micelles of a poly(ethylene oxide)-b-poly(propylene oxide)-b-poly(ethylene oxide) triblock copolymer Pluronic P84 in aqueous salt solution (2 M NaCl) has been studied by rheology, small-angle X-ray and neutron scattering (SAXS/SANS), and light scattering. Measurements of the flow curves by controlled stress rheometry indicated phase separation under flow. SAXS on solutions subjected to capillary flow showed alignment of micelles at intermediate shear rates, although loss of alignment was observed for high shear rates. For dilute solutions, SAXS and static light scattering data on unaligned samples could be superposed over three decades in scattering vector, providing unique information on the wormlike micelle structure over several length scales. SANS data provided information on even shorter length scales, in particular, concerning "blob" scattering from the micelle corona. The data could be modeled based on a system of semiflexible self-avoiding cylinders with a circular cross-section, as described by the wormlike chain model with excluded volume interactions. The micelle structure was compared at two temperatures close to the cloud point (47 degrees C). The micellar radius was found not to vary with temperature in this region, although the contour length increased with increasing temperature, whereas the Kuhn length decreased. These variations result in an increase of the low-concentration radius of gyration with increasing temperature. This was consistent with dynamic light scattering results, and, applying theoretical results from the literature, this is in agreement with an increase in endcap energy due to changes in hydration of the poly(ethylene oxide) blocks as the temperature is increased.     

Determination of phase transition temperatures of liquid crystals by a light scattering method

A simple analytical system using light scattering (LS) method has been developed to determine phase transition temperatures of liquid crystals (LCs). Intensity changes of the transmission light through a sample were measured as a function of temperature. All LCs and non-LCs showed appreciable changes in the transmission intensity at the phase transition temperature. The transition temperatures determined by the LS method were identical to those by differential scanning calorimetry (DSC).     

Shear flow effect on phase behavior and morphology in polymer blends

The effect of simple shear flow on the phase behavior and morphology was investigated for both polystyrene/poly(vinyl methyl ether) (PS/PVME) and poly(methyl methacrylate)/poly(styrene‐co‐acrylonitrile) (PMMA /SAN‐29.5) blends, which have LCST (lower critical solution temperature)‐type phase diagram. The measurements were carried out using a special shear apparatus of two parallel glass plates type. The PS/PVME blends showed shear‐induced demixing and shear‐induced mixing at low and high shear rate values, respectively. In addition, the rotation speed and the sample thickness were found to have a pronounced effect on the phase behavior under shear flow. On the‐other hand, PMMA/SAN blend showed only shear‐induced mixing and the magnitudes of the elevation of the cloud points were found to be composition and molecular weight dependent. The morphology of the PMMA/SAN=75/25 blend indicated that shear‐induced mixing occurred at a critical shear rate value, below which the two phases were highly oriented and elongated in the flow direction.     

DSC and p-V-T Study of PVC/PMMA Blends

Poly(vinyl chloride)/Poly(methyl methacrylate) — PVC/PMMA — blends were investigated by comparative p-V-T and differential scanning calorimetry (DSC) measurements. The study was concentrated on the glass transition range of the blends, and it was found that the blends are characterized by a single glass transition temperature suggesting miscibility of the blend components. It is shown that the glass temperature of the blends increases with both increasing heating rate and pressure. In parallel hereto one observes a decrease in the volume expansion coefficients, which is more accentuated for the polymeric melts than for the polymeric glasses. The dependence of the glass temperature on the composition of the polymer blends shows a sigmoidal behaviour which is due to the fact that positive deviations of the glass temperature from values predicted by additivity rules are observed in the high PVC concentration range, whereas in the high PMMA range negative deviations occur. This suggests a denser packing of the blends and thus a stronger interaction between the blend components in the high PVC concentration range. These packing differences increase with increasing pressure and decreasing heating rate and are generally more accentuated for the glass temperatures evaluated from p-V-T measurements.This revised version was published online in November 2005 with corrections to the Cover Date.     

Dynamic light scattering near the isotropic-blue phase transition of cholesteryl-oleylcarbonate

We report a light scattering study in the isotropic phase of a blue phase-forming fluid (cholesteryl-oleylcarbonate). An analysis of the intensity correlation function of the depolarized scattered light indicates that a two variable theory is not adequate to describe the intensity autocorrelation function. Our data are well-described by a stretched exponential decay of the collective orientational fluctuation. Such behaviour is usually observed in the vicinity of a glass transition. In addition we report measurements of the refractive index in the vicinity of the isotropic-blue phase transition.     

Miscibility and phase separation in SAN/PMMA blends investigated by positron lifetime measurements

Miscibility and phase separation in SAN/PMMA blends have been investigated using DSC, IR spectroscopy and positron lifetime spectroscopy (PLS). Single broad glass transition observed throughout the blend compositions, may be due to overlap of two glass transitions. IR measurements clearly indicate the absence of strong interactions. This supports miscibility is due to intramolecular repulsive forces in the SAN component. On the other hand, free volume data show negative deviation from linear additivity indicating the blends are miscible. The interchain interaction parameter β exhibits a complex behavior and the extent of miscibility is not revealed. Following Wolf’s treatment, we have evaluated the geometry factor γ and hydrodynamic interaction parameter α and found α is a suitable parameter in predicting the miscibility window. The cloud points in SAN/PMMA blends increase with decreasing PMMA content. The change in free volume size correlates well with the observed change in cloud point.     

Anomalous transition in aqueous solutions of a thermoresponsive amphiphilic diblock copolymer

The influence of shear flow on aggregation and disaggregation in aqueous solutions of the thermoresponsive methoxy-poly(ethylene glycol)-block-poly(N-isopropylacrylamide) (MPEG53-b-PNIPAAM113) copolymer that exhibits a lower critical solution temperature was investigated with the aid of turbidity, shear viscosity, and rheo small angle light scattering (rheo-SALS) methods. The turbidity results at quiescent conditions revealed a novel transition peak in the turbidity curve at intermediate temperatures, which reflects the delicate interplay between temperature-induced aggregation and shrinking of the species. A similar anomalous transition peak (located at the same temperature) was observed in the steady shear viscosity measurements at intermediate temperatures, and the amplitude of the peak was reduced with increasing shear rate as a consequence of breakup of interaggregate chains. At low temperatures (low sticking probability), enhanced shear rate generated interpolymer aggregates; whereas in the high-temperature domain (high sticking probability) association structures were broken up as the shear rate was increased. The rheo-SALS experiments disclosed growth of aggregates at low temperatures and destruction of association complexes at high temperatures. An increase of the cloud point temperature with rising shear rate is reported, which is interpreted as being a disruption of clusters under the influence of shear stresses.     

Using multimodal blends to elucidate the mechanism of flow‐induced crystallization in polymers

The effect of polydispersity on the formation of flow‐induced, oriented morphology in polyolefins is investigated by polarized light imaging and small angle X‐ray scattering. A torsional shear flow was applied at different temperatures to model polyethylene blends (bimodal and trimodal hydrogenated polybutadienes) comprising of two kinds of long chains with different molecular weight (1080 and 1770 kDa) in a matrix of short chains (18 KDa), and the results were compared to those of polydisperse materials. While a single boundary associated with the threshold flow conditions for the onset of oriented morphology is observed in the bimodal blends, two boundaries corresponding to the orientation of the longest chains (1770 kDa) and next longest chains (1080 kDa) are detected in the trimodal blends. The results obtained, herein, are extended by inference to polydisperse polymers. It is demonstrated that the shear rate dependence of the critical specific work parameter for the onset of oriented morphology in polydisperse polymers is dictated by the molecular weight distribution and that the longest chains mainly control the process with some contribution from shorter chains involved in the formation of flow‐induced precursors at higher flow rates. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Ultraviolet and visible Brillouin scattering study of viscous relaxation in 3-methylpentane down to the glass transition

Brillouin light scattering spectra from transverse and longitudinal acoustic waves in liquid and supercooled 3-methylpentane have been collected from room temperature down to 80 K, just above the glass transition. Spectra at different wave vectors have been obtained using 532 nm and 266 nm excitation. We found evidence of a shear relaxation with a characteristic time of 100 s at the glass transition which only partly accounts for the relaxation observed in the propagation and attenuation of the longitudinal modes. The inclusion of a relaxing bulk viscosity contribution with a relaxation time of the order of 10(2) ns at the glass transition is found to adequately reproduce the experimental data including transient grating data at a much lower frequency. A consistent picture of relaxed shear and bulk moduli as a function of temperature is derived. These two quantities are found to be related by a linear relation suggesting that a Cauchy-like relation holds also above the glass transition.     

Orientational and translational dynamics in room temperature ionic liquids

The authors investigate the dynamics of a series of room temperature ionic liquids, based on the same 1-butyl-3-methylimidazolium cation with different anions, by means of broadband (10(-6)-10(9) Hz) dielectric spectroscopy and depolarized light scattering in the temperature range from 400 K down to 35 K. Typical ionic conductivity is observed above the glass transition temperature Tg. Below Tg the authors detect relaxation processes that exhibit characteristics of secondary relaxations, as typically observed in molecular glasses. At high temperatures, the characteristic times of cation reorientation, deduced from the light scattering data, are approximately equal to the electric modulus relaxation times related to ionic conductivity. In the supercooled regime and close to Tg, the authors observe decoupling of conductivity from structural relaxation. Overall, room temperature ionic liquids exhibit typical glass transition dynamics, apparently unaltered by Coulomb interactions.     

DSC Studies of Thermally Induced Phase Separation of Hydrogen Bonded Polymer Blends

The thermally induced phase separation behavior of hydrogen bonded polymer blends, poly(n-hexyl methacrylate) (PHMA) blended with poly(styrene-co-vinyl phenol) (STVPh) random copolymers having various vinyl phenol contents, was studied by temperature modulated differential scanning calorimetry (TMDSC).The enthalpy of phase separation was determined to be about 0.5 cal g^–1 for one of the blends. A phase diagram was constructed from the TMDSC data for one of the blends. The kinetics of phase separation was studied by determining the phase compositions from the glass transition temperatures of quenched samples after phase separation. Subsequently, the phase separated samples were annealed at temperatures below the phase boundary to observe the return to the homogeneous state.This revised version was published online in November 2005 with corrections to the Cover Date.