加湿气体标准物质水含量分析

利用称量法、饱和蒸气压法、流量法3种不同原理的方法分析加湿气体标准物质中加湿量(水分的变化量),测定结果分别为4.66,4.68,4.70 g。依据3种方法的测量模型计算得到3个湿度量值的标准不确定度分别为0.016,0.025,0.666 g。为加湿后气体湿度值的量值溯源提供了3种可靠的方法,为加湿气体标准物质的制备和水含量溯源提供了新思路。     

Investigations on the water content of candidate reference material CRM 679 cabbage powder

The determination of the residual water content by thermal methods and especially by Karl Fischer titration in a candidate reference material of the European Commission (candidate CRM 679 cabbage powder) is described and discussed.     

Investigations on the water content of candidate reference material CRM 679 cabbage powder

The determination of the residual water content by thermal methods and especially by Karl Fischer titration in a candidate reference material of the European Commission (candidate CRM 679 cabbage powder) is described and discussed.     

Properties of plasma membranes from granulation tissue with reference to extracellular matrix.

Treatment with neuraminidase decreased the activity of Na+,K+-activated Mg2+-adenosine triphosphatase in plasma membranes isolated from experimental granulation tissue but not that of 5'-nucleotidase or leucine-beta-naphthylamidase. A temporary lowering of the pH of the plasma membrane suspension to 2-3 inactivated all three enzymes, which remained inactive after the pH had been readjusted to 7.4. Addition of dextran preparations to the membrane suspension decreased the activity of adenosine triphosphatase. Ethanol (0.4%) had a similar effect. These marker enzymes of plasma membranes were not affected by additions of hyaluronate, chondroitin sulfate, protein polysaccharide or soluble collagen. Serotonin stimulated the adenosine triphosphatase activity slightly. About 10-20% of the protein in the plasma membrane preparation was extracted with EDTA. This "fuzzy coat" fraction yielded a distinct gel-electrophoretic protein pattern. Hyaluronidase was not helpful in cleaving this surface layer from the plasma membranes.     

Selenomethionine content of candidate reference materials

Selenium has been identified as an antioxidant of importance in the diet. Accurate determination of its chemical forms depends on the availability of suitable reference materials (RMs). Two candidate reference materials for determination of selenomethionine (Semet) in food-related materials, a standard wheat gluten sample (NIST RM 8418 Wheat Gluten) and a commercial selenium enriched yeast, have been examined by use of a gas chromatography–isotope dilution mass spectrometry (IDMS) procedure, after treatment of the matrix with 0.1 mol L^–1 hydrochloric acid containing stannous chloride, addition of CNBr, and extraction with chloroform. This procedure results in cleavage of the CH₃Se group to form volatile CH₃SeCN. Addition of isotopically enriched ⁷⁴Semet to an analytical sample enables estimation of the naturally occurring protein-bound ⁸⁰Semet by IDMS without a protein-digestion process. We found that the Wheat Gluten RM contains a significant amount of Semet as a portion of its assigned value of 2.58 μg Se_total g^–1. Commercial selenium yeast tablets are labeled as containing an elevated level of “organic selenium”, usually as Semet. The sample we investigated contained 210 μg Se_total g^–1 sample as determined separately by IDMS, measuring elemental selenium after digestion. 73% of this total (153±21 μg Se_Semet g^–1; n = 23) was present as Semet. Thus, these two materials contain significant amounts of their total selenium content as Semet and would be good candidates for further study and characterization as reference materials for determining this important food component. The CNBr reaction used will also enable the determination of Se-(methyl)selenocysteine, the biological role of which is of recent interest. In addition to matrix RMs for Semet, it is important to have standard materials of the pure substance. We have examined a sample of a candidate standard material of selenomethionine being prepared by the USP. It was confirmed that this material is pure selenomethionine. Received: 13 December 2000 / Revised: 5 March 2001 / Accepted: 12 March 2001     

The determination of antimony in natural waters with particular reference to sea water

A procedure is described for the determination of antimony in natural waters at concentrations down to 0.1 μg/l or less. The element is concentrated by coprecipitation with hydrous manganese dioxide (produced by the reaction of permanganate with ethanol). It is separated from manganese, iron and interfering elements by extraction from 5 M sulphuric acid, 0.01 M with respect to iodide, using methyl isobutyl ketone. After back-extraction with 0.4 M hydrochloric acid, it is determined photometrically using rhodamine B. The overall chemical yield of the process is measured radiochemically and amounts to ca. 80%. Sea water samples from the Irish Sea were found to contain 0.13–0.40 μg Sb/l.     

Characterization of water content in biodiesel fuel certified reference material (NMIJ CRM 8302-a)

The National Metrology Institute of Japan has issued a certified reference material of biodiesel fuel derived from palm oil (NMIJ CRM 8302-a) for the measurement and quality control of water, methanol, six elements (sulfur, phosphorus, sodium, potassium, magnesium, and calcium), density, and kinematic viscosity. This paper presents the technical details for the characterization of the water content in NMIJ CRM 8302-a. Because the water content in biodiesel is easily affected by ambient humidity, sample handling is extremely difficult. Thus, a sample handling technique that overcomes this limitation was established, and optimized coulometric and volumetric Karl Fischer titrations were performed in order to accurately determine the water content with traceability to the International System of Units. The certified water content and its expanded uncertainty with a coverage factor k = 2 were 393 mg kg^?1 and 25 mg kg^?1, respectively.     

The determination by radioactivation of the oxygen content of powdered metals with particular reference to beryllium

A radioactivation method for the determination of oxygen in beryllium metal powder is described. The sample, mixed with, lithium fluoride, is irradiated in the Harwell Pile, fluorine-18 chemically separated and its activity compared with that from standards similarly treated.The method has given reproducible results in reasonable agreement with those obtained by several other methods which were being investigated simultaneously.     

Gelled emulsions with a high water content

The structure of a gel containing 99% water, 0.5% of a nonionic surfactant and 0.5% of a hydrocarbon was investigated by analysis of its equilibrium phases and their state of dispersion by liquid helium freeze fracture electron microscopy.The gel consisted of aqueous droplets of micron size separated by a thin membrane of a lamellar liquid crystal and a W/O microemulsion with droplets varying between 200 and 1000 Å in diameter.     

The automatic determination of silicate-silicon in natural waters with special reference to sea water

An automatic method using a Technicon AutoAnalyzer is described for the determination of silicate in natural waters in the range 0–4 mg Si/l. It is based on the conversion of silicate to β-silicomolybdic acid which is reduced by means of a metolsulphite reagent to molybdenum blue. Interference of phosphate is prevented by oxalic acid. The relationship between silicate concentration and optical density is linear in both fresh waters and sea water. With sea water the salt error of the method is ca. 5% at a salinity of 35‰ A coefficient of variation of 0.8% was found at a silicate concentration of 1 mg Si/l with both fresh and sea waters.     

Selenomethionine content of candidate reference materials.

Selenium has been identified as an antioxidant of importance in the diet. Accurate determination of its chemical forms depends on the availability of suitable reference materials (RMs). Two candidate reference materials for determination of selenomethionine (Semet) in food-related materials, a standard wheat gluten sample (NIST RM 8418 Wheat Gluten) and a commercial selenium enriched yeast, have been examined by use of a gas chromatography-isotope dilution mass spectrometry (IDMS) procedure, after treatment of the matrix with 0.1 mol L(-1) hydrochloric acid containing stannous chloride, addition of CNBr, and extraction with chloroform. This procedure results in cleavage of the CH3Se group to form volatile CH3SeCN. Addition of isotopically enriched 74Semet to an analytical sample enables estimation of the naturally occurring protein-bound 80Semet by IDMS without a protein-digestion process. We found that the Wheat Gluten RM contains a significant amount of Semet as a portion of its assigned value of 2.58 microg Se(total g(-1). Commercial selenium yeast tablets are labeled as containing an elevated level of "organic selenium", usually as Semet. The sample we investigated contained 210 microg Se(total) g(-1) sample as determined separately by IDMS, measuring elemental selenium after digestion. 73% of this total (153 +/- 21 microg Se(semet) g(-1); n = 23) was present as Semet. Thus, these two materials contain significant amounts of their total selenium content as Semet and would be good candidates for further study and characterization as reference materials for determining this important food component. The CNBr reaction used will also enable the determination of Se-(methyl)selenocysteine, the biological role of which is of recent interest. In addition to matrix RMs for Semet, it is important to have standard materials of the pure substance. We have examined a sample of a candidate standard material of selenomethionine being prepared by the USP. It was confirmed that this material is pure selenomethionine.     

Water content variation of p-n-heptylphenol reference material

Water content variation of candidate p-n-heptylphenol (HP) reference material (ampoule form) for preparation of a primary standard solution based on the Japan Calibration Service System, a national standards dissemination system, under the Measurement Law of Japan, was examined by a Karl-Fischer water content meter. As prepared samples, liquid-phase HP and upper, middle, and lower layers of solid-phase HP were measured since characteristic phase transition occurs near room temperature (melting point: 28.98 °C). As a result of water content in liquid- and solid-phase HP, water content variation among three layers of solid-phase is found in within ampoules, though water content variation of liquid-phase is not found. Between-ampoule variation of water content is also found using total ampoules of liquid-phase HP used to eliminate within-ampoule variation. Moreover, water content variation is secondarily confirmed by the results of the amount-of-substance fraction of HP based on a differential scanning calorimeter. From these results in this study, it is concluded that within- and between-ampoule variations of water content may depend on phase transition and water loss during ampouling of candidate reference material, respectively.     

Establishment of SI-traceable reference ranges for the content of various elements in the IMEP-9 water sample

 The International Measurement Evaluation Programme (IMEP) attempts to shed light on the current state of the practice in chemical measurements. The main tool, which assists this attempt and also differentiates IMEP from similar projects, is the establishment of SI-traceable reference ranges (where possible) for the elements offered for measurement to the participants for every IMEP round. The Institute for Reference Materials and Measurements (IRMM), as the founder and co-ordinator of IMEP has the responsibility of establishing the SI-traceable reference ranges. This is a large task that requires knowledge, skill and resources. IRMM collaborates with a network of reference laboratories in order to achieve the establishment of SI-traceable reference ranges in a transparent and reliable way. The IMEP reference laboratories must have demonstrated experience and have a proven and successful record in the use of primary methods of measurements (mainly isotope dilution mass spectrometry) and the application of uncertainty evaluation according to ISO/BIPM guidelines. In IMEP-9 "trace elements in water", results from 7 reference laboratories (including IRMM) were combined by IRMM to establish SI-traceable ranges for the 15 elements, which were then offered for measurement to the 200 participants worldwide. This paper does not discuss the individual contribution of the reference laboratories (this could be the subject of individual papers) but describes the procedures and criteria used in order to establish the reference ranges for the IMEP-9 samples by combining the individual contributions. All results submitted to IRMM are included, so as to make this publication as realistic as possible. Received: 31 December 1999 / Accepted: 7 March 2000     

Determination of the water content of foods : Indirect determination of the water content

The indirect determination of the water content of foods is dealt witli on the basis of tlie following general considerations: A. The absolute vapour pressure of the water in the substance to be desiccated ; B. The absolute vapour pressure of the water in the surrounding air, C. Behaviour of the non-water components of the substance to be desicented , D. Special causes of errors, viz.: 1.. Retardation in the establishment of equihbrium; 2. Retardation due to title structure of the substancc to be desiccated, 3. Crust formation; 4. Analytical errors. E. Rate of desiccation: reference methods and rapid routine methods.We prefer to consider the problems relating to the indirect determination of the water content on the basis of absolute water vapour pressures. The advantages and disadvantages of this method of treatment have been indicated.     

Properties of nanocrystalline electrodeposited CoFeP alloy with low phosphorus content

CoFe and low phosphorus containing (<4 at.%) CoFeP alloy films were electrodeposited from NaH₂PO₂ containing solutions at pH 4 on copper substrates under galvanostatic conditions. At the low phosphorus composition, nanocrystalline CoFeP alloy films are formed. The structure, composition and morphology of the thin films were studied using X-ray diffraction, energy dispersive spectroscopy and atomic force microscopy. The magnetic properties of the film were studied using superconducting quantum interference device magnetometer. The thin film performance features were explained on the basis of microstructural features developed during deposition. Whereas the electrodeposited CoFe alloy thin film exhibited mixed hcp and fcc phase structure in the absence of phosphorus, the low phosphorus containing thin film exhibited an increasing mixed bcc and hcp phase structure as its phosphorus content increases, showing modification in the grain size morphology and magnetic properties. In addition to applied current, the amount of P co-deposited in CoFeP alloy depends on the concentration of NaH₂PO₂ source in the bath. Qualitative analysis of the Tafel slope of CoFe and CoFeP deposition suggests that the presence of P in the CoFe deposit does not affect the mechanism of anomalous deposition of Co and Fe, thereby suggesting that CoFeP deposition is anomalous.     

Phase equilibrium in a water + n-hexane system with a high water content

Russian Journal of Physical Chemistry A - The Р, ρ, and Т-properties of a water + n-hexane system immiscible under normal conditions are measured piezometrically in the water mole...     

Production of three certified reference materials for water content based on mixed solutions of butanol, xylene and propylene carbonate

Certified reference materials (CRMs) for water content with good accuracy and homogeneity are required for calibration or validation of the Karl Fischer titration and for establishing the traceability of water content results. Three such CRMs were produced and certified: GBW 13512, 13513 and 13514 are based on solvent mixtures consisting of butanol, xylene and propylene carbonate with water contents of 10.01, 1.067 and 0.139?mg/g, respectively, certified by the Karl Fischer coulometric and volumetric methods. These CRMs were prepared, dispensed and sealed under a humidity equal to the equilibrated humidity of their headspace. In this way, the between-bottle homogeneity uncertainty (u _H,rel) could be kept as low as u _H,rel?=?0.12?% for GBW 13512. The certification methods, that is, Karl Fischer coulometric and volumetric methods, were calibrated using in-house water standards prepared by gravimetry. The results were traceable to the SI unit of mass. The relative deviation of the water contents between the two methods for GBW 13512 was only 0.05?%. The expanded uncertainty (U, k?=?2) of three CRMs was 0.12, 0.024 and 0.012?mg/g, respectively. These CRMs for water content with good accuracy can be applied in the calibration or validation of measurement procedures to ensure accurate and comparable results.     

吸收称量法测定天然气中的水含量

一般而言,从气藏产出的天然气会含有一定量的水;另一方面,天然气在输送过程中通过积存有水的管网,也会携带一部分水.水会形成水合物,可能引起管线水堵.     

Certification of the sulphur content of three rapeseed reference materials

Summary The sulphur content of three rapeseed reference materials has been certified on the basis of measurements made by inductively coupled plasma-optical emission spectroscopy, isotope-dilution mass spectrometry and ion chromatography. Their suitability for the calibration of x-ray fluorescence spectrometers used for measuring sulphur in rapeseed samples was established.