Synthesis and eutectic behavior of liquid crystalline copolyesters

A series of liquid crystalline copolyesters, derived from 1,4‐hydroxy‐benzoic acid (HBA), 6‐hydroxy‐2‐naphthoic acid (HNA), terephthalic acid (TA), and hydroquinone (HQ), were prepared; crystallization, melting and solid‐state structure of the copolyesters were studied by using differential scanning calorimetry (DSC) and wide‐angle x‐ray diffraction (WAXD). It was found that the variation of melting point of the copolyesters with increasing HBA mol % exhibits eutectic melting behavior at a constant mole ratio of HNA, and the extrapolated eutectic temperature decreases linearly with increasing HNA mol %. WAXD analysis of the copolyesters indicates that the d‐spacing related to three‐dimensional order increases first and then decreases with increasing HBA mol %. The increase of the d‐spacing, consistent with looser packing of chains, leads to the reduction of melting point and most likely accounts for the eutectic behavior observed. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2171–2177, 2009     

Mechanical and dielectric relaxations in liquid crystalline copolyesters

Dynamic mechanical measurements in tension and torsion on oriented tapes and monofilaments of a range of liquid crystalline polyesters have been combined with dielectric measurements to obtain a molecular understanding of the relaxation processes. This paper extends our previous work [1,2,3] on polyesters of hydroxybenzoic acid (HBA) and hydroxynaphthoic acid (HNA) to related polymers containing dihydroxynaphthalene (DHN) and terephthalic acid (TPA) or biphenyl (BP) and TPA in place of the HNA. It confirms the association of the β and γ processes with naphthyl and phenyl moieties but shows that the processes cannot be due simply to the independent motions of single units.     

Structural characterization of thermotropic liquid crystalline dihydroxydicarbosilane mesophase

Molecular mechanics (MM) calculations of the structure formed by bis(hydroxydimethylsilyl)methane [(CH3)2(HO)Si]2CH2(MDCS) molecules have been performed. The calculations lead us to conclude that MDCS can form a columnar liquid crystalline phase which consists of supramolecular H-bonded associates similar to those found earlier for siloxane compounds of the same type. Synthesis of MDCS was performed. IR, NMR, DSC and XRD (powder and single crystal) investigations have shown the existence of a LC phase in a narrow temperature range. The computational and experimental results suggest the existence of similar columnar LC phases in a wider temperature range for Et-, Pr-, and Bu-substituted bis(hydroxydialkylsilyl)methane.     

Stiff chain persistence lengths in liquid crystalline copolyesters

This paper describes a continuation of our X-ray diffraction work on the structure of the mesomorphic copolyesters prepared from p-hydroxybenzoic acid (HBA) and 2-hydroxy-6-naphthoic acid (HNA). The X-ray patterns of meltspun fibers of these copolymers show a series of aperiodic meridional maxima, and these are predicted by a model consisting of stiff extended chains of completely random copolymer sequence. The calculated intensity data are independent of the chain length for the model, except that the width of the peak at d≃2.1Å decreases with increasing chain length. For 58/42 copoly(HBA/HNA) the best agreement obtained is for a chain length of 11 monomers, and this corresponds to a correlation or persistence length for the stiff chain conformation in the solid state. This effect has been modeled for an infinite chain by deriving experimental monomer length distribution functions, from a survey of the conformations of models of typical random chain sequences. The distribution function is then incorporated into the intensity calculations and leads to prediction of peak widths that are comparable to those observed.     

Mesoscopic structure and properties of liquid crystalline mesophase pitch and its transformation into carbon fiber

The history and present state of the art in the chemistry of mesophase pitch, which is an important precursor for carbon fiber and other high-performance industrial carbons, are reviewed relative to their structural properties. The structural concepts in both microscopic and macroscopic views are summarized in terms of the sp(2) carbon hexagonal plane as a basic unit common to graphitic materials, its planar stacking in clusters, and cluster assembly into microdomains and domains, the latter of which reflect the isochromatic unit of optical anisotropy. Such a series of structural units is described in a semiquantitative manner corresponding to the same units of graphitic materials, although the size and stacking height of the hexagonal planes (graphitic sheets) are very different. Mesophase pitch is a liquid crystal material whose basic structural concepts are maintained in the temperature range of 250 to 350 degrees C. The melt flow and thermal properties are related to its micro- and mesoscopic structure. The structure of mesophase-pitch-based carbon fiber of high tensile strength, modulus, and thermal conductivity has been formed through spinning, and has inherited the same structural concepts of mesophase pitch. Stabilization settles the structure in successive heat treatments up to 3000 degrees C. Carbonization and graphitization enable growth of the hexagonal planes and their stacking into units of graphite. Such growth is governed and controlled by the alignment of micro- and mesoscopic structures in the mesophase pitch, which define the derived carbon materials as nanostructural materials. Their properties are controlled by the nanoscopic units that are expected to behave as nanomaterials when appropriately isolated or handled.     

Analysis of mesophase formation in side-chain liquid crystalline polycarbosilanes

This paper is concerned with an analysis of the thermodynamics and kinetics of mesophase formation by cooling from the isotropic state of side-chain liquid crystalline polycarbosilanes containing spacers in the range from 3 to 11 CH₂-groups. The polymers are characterized by their thermotropic behaviour as far as temperature, enthalpy and entropy of the transitions are concerned. The kinetics was followed by optical and calorimetric methods. Longer spacer length leads to more perfect ordering in the mesophase, higher isotropization temperatures, and lower glass transition temperatures. The Avrami and Ozawa formalism to describe the transition kinetics to the mesophase from the isotropic state cannot be interpreted as the nucleation and growth mechanism known from crystallization.Dedicated to Professor Bernhard Wunderlich on the occasion of his 65th birthday     

Miscibility and transesterification in blends of liquid crystalline copolyesters and polyarylate

Blends of poly(oxybenzoate-p-ethylene terephthalate) (POB-PET) and polyarylate were confirmed to be a partially miscible system by differential scanning calorimetry. When 60/40 POB-PET/PAr blend was annealed at high temperature (above 270°C) for several minutes, the ester–ester interchange (transesterification) in the blend took place immediately, as evidenced by Fourier Transformed infrared analyses. The analysis of the blend annealed at 290°C by ¹H-¹³C nuclear magnetic resonance disclosed that there were four new diads appearing in 15 min and an additional one produced in 60 min during the heat treatment. The miscibility between POB-PET and polyarylate increased with the mol concentration of these new diads judging from differential scanning calorimetry. The evolution of the concentration of the diad ethylene glycol-isophthalate during the annealing can be described by a second-order reaction. The activation energy of forming the diad ethylene glycol-isophthalate was 26.5 kcal/mol, and the preexponential factor for the transesterification reaction is 3.7 × 10⁸ min⁻¹. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1959–1969, 1998     

Origin of lyotropic liquid crystalline mesophase formation and liquid crystalline to mesostructured solid transformation in the metal nitrate salt-surfactant systems

The zinc nitrate salt acts as a solvent in the ZnX-C(12)EO(10) (ZnX is [Zn(H(2)O)(6)](NO(3))(2) and C(12)EO(10) is C(12)H(25)(OCH(2)CH(2))(10)OH) lyotropic liquid crystalline (LLC) mesophase with a drastic dropping on the melting point of ZnX. The salt-surfactant LLC mesophase is stable down to -52 °C and undergoes a phase change into a solid mesostructured salt upon cooling below -52 °C; no phase separation is observed down to -190 °C. The ZnX-C(12)EO(10) mesophase displays a usual phase behavior with an increasing concentration of the solvent (ZnX) in the media with an order of bicontinuous cubic(V(1))-2D hexagonal(H(1))--a mixture of 2D hexagonal and micelle cubic(H(1) + I)-micelle cubic(I)-micelle(L(1)) phases. The phase behaviors, specifically at low temperatures, and the first phase diagram of the ZnX-C(12)EO(10) system was investigated using polarized optical microscopy (POM), X-ray diffraction (XRD), differential scanning calorimetry (DSC), Fourier transform infrared (FTIR), and Raman techniques and conductivity measurements.     

Evolution of structure and properties of a liquid crystalline epoxy during curing

The evolution of structure, and thermal and dynamic mechanical properties of a liquid crystalline epoxy during curing has been studied with differential scanning calorimetry (DSC), polarized optical microscopy, x-ray scattering, and dynamic mechanical analysis. The liquid crystalline epoxy was the diglycidyl ether of 4,4′-dihydroxy-α-methylstilbene (DGEDHMS). Two curing agents were used in this study: a di-functional amine, the aniline adduct of DGEDHMS, and a tetra-functional sulfonamido amine, sulfanilamide. The effects of curing agent, cure time, and cure temperature have been investigated. Isothermal curing of the liquid crystalline epoxy with the di-functional amine and the tetra-functional sulfonamido amine causes an increase in the mesophase stability of the liquid crystalline epoxy resin. The curing also leads to various liquid crystalline textures, depending on the curing agent and cure temperature. These textures coarsen during the isothermal curing. Moreover, curing with both curing agents results in a layered structure with mesogenic units aligned perpendicular to the layer surfaces. The layer thickness decreases with cure temperature for the systems cured with the tetra-functional curing agent. The glass transition temperature of the cured networks rises with increasing cure temperature due to the increased crosslink density. The shear modulus of the cured networks shows a strong temperature dependence. However, it does not change appreciably with cure temperature. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2363–2378, 1997     

Diamagnetic susceptibility of liquid crystalline copolyesters: Study of molecular relaxation

The diamagnetic susceptibility of a series of random copolyesters, P(HB/HN), of 4-hydroxybenzoic acid (HBA) with 2-hydroxy-6-naphtoic acid (HNA) has been investigated, both, as a function of composition and temperature. It is shown that the molecular susceptibility of the uniaxially oriented samples linearly decreases with HB content. Results are discussed in terms of the increase in magnetic anisotropy occurring with the introduction of the HN groups. Furthermore, the temperature dependence of the specific susceptibility has been investigated. The diamagnetic susceptibility of these copolymers rises at the beginning of the solid-liquid crystalline transition. Above this temperature, the specific susceptibility exhibits a conspicuous time-dependent behavior which is a function of the temperature at the mesophase. After long storage times at the mesophase, and upon cooling at room temperature, the susceptibility shows values which approach those of a macroscopically isotropic state, i.e., a state with no overall preferred orientation. X-ray diffraction measurements confirm a relaxation mechanism of the molecular orientation occurring at temperatures above the melting point. A similar relaxation process is observed for samples with an initial planar orientation. © 1996 John Wiley & Sons, Inc.     

Surface microcracks decoration and disclination defects of wholly aromatic liquid crystalline copolyesters

An intensive study has been conducted to map the director fields of disclination of nematic liquid crystalline copolyesters. In this study, films of two wholly aromatic main-chain polyesters containing para- (ABA/MH/TFTA) and meta-linkages (ABA/MH/TFIA) (ABA, p-acetoxybenzoic acid; MH, maleic hydrazine; TFTA, tetrafluoroterephthalic acid; TFIA, tetrafluoroisophthalic acid) were synthesized to investigate the effects of kinks on liquid crystallinity, disclination strength (S), and surface microcracks decoration. These two copolyesters were prepared by in-situ thin film polymerization and characterized by polarizing light microscope, wide-angle X-ray diffraction, as well as "rotational isomeric states" (RIS) Metropolis Monte Carlo (RMMC) simulation. An optical microscope shows that the surface microcracks forms in the nematic-mosaic texture during a rapid quenching. The ABA/MH/TFTA film exhibits disclination strength with S = +1 and S = -(1)/(2); however, disclination strengths with S = +/-1 have been observed in the ABA/MH/TFIA system. To our best knowledge, this is the first paper reporting the effects and evidence of kink (meta and para moieties) on topological defect of disclination. In addition, the RMMC analysis supports the liquid crystal formation in both polyester films with a persistence ratio greater than 6.42.     

Effect of pyridazine structure on thin‐film polymerization and phase behavior of thermotropic liquid crystalline copolyesters

An intensive study has been conducted to compare the effects of malei hydrazine (MH) and hydroquinone (HQ) on the liquid crystallinity and phase transition behavior in the ABA/HQ/TFTA and ABA/MH/TFTA copolyesters (p‐acetoxybenzoic acid (ABA) and tetrafluoroterephthalic acid (TFTA)). These two copolyesters were prepared by thin‐film polymerization and characterized by differential scanning calorimetry (DSC), polarizing light microscope (PLM), wide‐angle X‐ray diffraction (WAXD), as well as Cerius² computational simulation. Characterization and comparison of the liquid crystalline (LC) evolution and morphology changes of HQ moiety with corresponding MH moiety suggest that ABA/MH/TFTA system is energetically favorable to mesophase formation than ABA/HQ/TFTA system. When the films are quenched, a surface microcrack decoration is observed in both systems. Both systems, which have the persistence ratio larger than 6.42, satisfy the minimum requirement for the LC formation by molecular science software. The ABA/MH/TFTA film exhibits only one single peak transition. However, two distinct transitions have been observed in the ABA/HQ/TFTA system. The average Avrami exponent, n, is ～1.2, and PLM and WAXD results suggest mesophase transition in ABA/MH/TFTA film. As reflected by the results obtained from PLM, WAXD, and DSC studies, the phase transition is confirmed as crystal → nematic → isotropic in ABA/HQ/TFTA copolyester. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2230–2242, 2005     

Thermally stable liquid crystalline thermosets based on aromatic copolyesters: Preparation and properties

The synthesis and physical properties are described for a thermally stable liquid crystalline (LC) thermoset based on all aromatic ester units. The persistence of the liquid crystalline phase throughout the curing process was monitored with polarizing optical microscopy. The applicability of these new liquid crystalline thermosets has been evaluated for use as an adhesive for bonding metals, namely titanium. The failure of the adhesive bonds always occurs within the polymer; thus it can be inferred that bonding at the polymer-metal interface is very good. This strong interfacial bonding is attributed to low cure shrinkage and CTE matching of the underlying substrate by the LC resins. The cohesive properties and strength of the cured resin can be greatly enhanced by the addition of filler materials. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35:1061–1067, 1997     

Transesterification kinetics in the reactive blends of liquid crystalline copolyesters and poly(ethylene terephthalate)

The transesterification kinetics of poly(ethylene terephthalate) (PET)/copoly(oxybenzoate-p-terephthalate) (liquid crystalline polymer, LCP) (70/30 by weight) in the presence of small amount of bis(2-oxazoline) (BOZ) as chain extender was studied by using 1H nuclear magnetic resonance. The kinetic data was treated as a second-order reversible reaction, and it was found that the rate constants of transesterification at 270, 280 and 290 °C were 1.55×10⁻², 2.20×10⁻² and 3.01×10⁻² min⁻¹, respectively, the value of which was higher than the blend without addition of BOZ, 1.26×10⁻² min⁻¹, and the activation energy of PET/LCP transesterification was 84.4 kJ mol⁻¹.     

Influence of the mesophase structure on the β-relaxation in liquid crystalline poly(meth)acrylates

The dependence of the rotation of the mesogenic unit around its long axis (β-relaxation) on the actual mesophase in liqid crystalline polymethacrylates and polyacrylates was studied by dielectric spectroscopy in the frequency range from 10⁻² Hz to 10⁶ Hz and in a temperature range from 170 K to 430 K. As mesogenic units derivatives of (p-alkoxy-phenyl)-benzoate were used where different mesophases were achieved by small variation of the mesogenic structure, the spacer length and the tail group of the mesogenic unit. For all samples the temperature dependence of the relaxation rate of the β-relaxation can be described by an Arrhenius equation where both the pre-exponential factor and the activation energy increase significantly with the order of the mesophase. To characterize the structure X-ray measurements were also carried out. The mean lateral mesogenic distance was correlated directly with relaxational quantities.     

A comparative dielectric study on the molecular dynamics of the liquid crystalline and the amorphous state of copolyesters

The complex dielectric permittivity has been measured in the 10³−10⁶ Hz frequency range for selected random copolyesters of poly(ethylene terephthalate). The variation of the dielectric properties with temperature has been qualitatively related mainly to two processes. The α relaxation, which is associated with the glass transition, has been shown to be dependent on the molecular order of the systems. The β relaxation process has been assigned to local motions of the ester groups attached to both sides of the aromatic rings. The β process is also shown to exhibit a dependence on molecular order.     

Crystallization and melting behavior of liquid crystalline copolyesters based on poly(ethylene terephthalate)

A series of copolyesters were prepared by the incorporation of p‐hydroxybenzoic acid (HBA), hydroquinone (HQ), and terephthalic acid (TA) into poly(ethylene terephthalate) (PET). On the basis of viscosity measurements, high molar mass copolyesters were obtained in the syntheses, and ¹H‐NMR analyses indicated the total insertion of comonomers. They exhibit nematic phase above melting temperature, as observed by polarized light microscope (PLM). Their crystallization and melting behaviors were also studied by differential scanning calorimetry (DSC) and wide angle X‐ray diffraction (WAXD). It was found that these copolyesters are more crystalline than copolyesters prepared from PET and HBA. Introduction of HQ/TA disrupts longer rigid‐rod sequences formed by HBA, and thus enhances molecular motion and increases crystallization rate and crystallinity. Isothermal crystallization at solid phase polymerization conditions (up to 24 h at 200°C) resulted in increased copolymer randomness (by NMR) and higher melting point, the latter attributed to structural annealing. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 369–377, 1999     

Synthesis and mesophase characterization of liquid crystalline polyesters with bulky,rigid, lateral substituents

The synthesis and characterization of aromatic polyesters containing various symmetrically di-substituted hydroquinone monomers is described. The homopolyesters made from these monomers and terephthalic acid (TA) did not melt. Copolyesters of TA with mono- and di-substituted hydroquinone formed liquid crystalline melts. Optical microscopy showed schlieren, marbled, and droplet textures characteristic of the nematic phase. DSC experiments were also in accord with mesophase formation as multiple transitions characteristic of first-order phase changes were found. In general, the crystal-nematic transition was about 300°C, whereas the nematic-isotropic change was over 400°C. All the polyesters were prone to decomposition near or above the isotropization temperature. © 1994 John Wiley & Sons, Inc.