Stress-optical coefficient of cis-1,4-polybutadiene and cis-1,4-polyisoprene networks. Measurements on cis-1,4-polybutadiene networks and theoretical interpretation

Stress, strain, and birefringence measurements have been carried out on swollen and unswollen networks of ′cis-1,4-polybutadiene polymers. Neither stress-strain nor birefringence-strain relations of unswollen specimens obey the Gaussian network theory, but both can be fitted by the Mooney-Rivlin equation. On the contrary, data on specimens swollen in tetralin, decalin, benzene, and carbon tetrachloride strictly obey the Gaussian network theory. Existing methods for evaluating the temperature coefficient of the unperturbed dimensions, d In 〈r²〉/dT, from the stress-temperature relation are applied to the present data and discussed in some detail. It is concluded that reliable values of d In 〈r²〉/dT are not obtainable from data on unswollen samples because of the pronounced non-Gaussian effect. The value 7.5 ų for the optical anisotropy ų (an alternative to the stress-optical coefficient) for unswollen specimens is markedly larger than values (5.8 ų on the average) for swollen specimens. This is interpreted as due to the shortrange orientational order among polymer segments. The quantities 〈r²〉, ΔΓ, and their temperature coefficients are calculated for both cis-1,4-polybutadiene and cis-1,4-polyisoprene chains, on the basis of the rotational isomeric state approximation for bond rotations. Values of ΔΓ for cis-1,4-polybutadiene calculated using Clément and Bothorel's set of anisotropic bond polarizabilities are in good agreement with observed values for swollen specimens. Those for cis-1,4-polyisoprene obtained using the same set of anisotropic bond polarizabilities are somewhat smaller than observed values for unswollen specimens. This departure is in the direction expected from the behavior of ΔΓ upon swelling (i.e., a decrease in ΔΓ upon swelling).     

Polymerization of (E)‐1,3‐Pentadiene and (E)‐2‐methyl‐1,3‐pentadiene with neodymium catalysts: Examination of the factors that affect the stereoselectivity

(E)‐1,3‐Pentadiene (EP) and (E)‐2‐methyl‐1,3‐pentadiene (2MP) were polymerized to cis‐1,4 polymers with homogeneous and heterogeneous neodymium catalysts to examine the influence of the physical state of the catalyst on the polymerization stereoselectivity. Data on the polymerization of (E)‐1,3‐hexadiene (EH) are also reported. EP and EH gave cis‐1,4 isotactic polymers both with the homogeneous and with the heterogeneous system, whereas 2MP gave an isotactic cis‐1,4 polymer with the heterogeneous catalyst and a syndiotactic cis‐1,4 polymer, never reported earlier, with the homogeneous one. For comparison, the results obtained with the soluble CpTiCl₃‐based catalyst (Cp = cyclopentadienyl), which gives cis‐1,4 isotactic poly(2MP), are examined. A tentative interpretation is given for the mechanism of the formation of the stereoregular polymers obtained and a complete NMR characterization of the cis‐1,4‐syndiotactic poly(2MP) is reported. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3227–3232     

1,4 polymerization of isoprene by titanate catalyst systems

Titanates are versatile in the 1,4 polymerization of isoprene. The (R′O)₄Ti/RAlCl₂ catalyst gives either cis- or trans-1,4-polyisoprene, depending on the nature of both the titanate and the solvent. Primary titanates give cis-1,4-polyisoprene in both aliphatic and aromatic solvents. Secondary titanates give cis-polyisoprene in aliphatic solvents, and trans-1,4-polyisoprene in aromatic solvents. Tertiary titanates give trans-polyisoprene in both aliphatic and aromatic solvents. A mechanism is postulated which takes into consideration the role of the solvent. ESR studies of the various titanate–RAlCl₂ catalysts were made; the paramagnetic structures are related to polymerization mechanisms.     

Isomerization of chemically activated bicyclo[3.1.0]hex-2-ene and related C6H8 isomers

Singlet methylene was reacted with cyclopentadiene to give chemically activated bicyclo[3.1.0]hex-2-ene (BCH). The rate of isomerization of BCH to 1,4-cyclohexadiene, 1,3-cyclohexadiene, cis-1,3,5-hexatriene, and l-methylcyclopentadiene is compared with calculated rate constants using the RRKM theory and measured or estimated thermal Arrhenius parameters. Subsequent isomerizations of the C₆H₈ products are also measured and calculated. These include 1,4-cyclohexadiene to benzene and the reversible reactions between 1,3-cyclohexadiene, cis-1,3,5-hexatriene, and trans-1,3,5-hexatriene. The results provide new data for several of these reactions which have not been observed in thermal studies. Agreement between the observed and calculated rates using the strong collision assumption is satisfactory except for the trans-1,3,5-hexatriene to cis-1,3,5-hexatriene reaction.     

Polymérisation radicalaire du pentadiène-1,3. II. Microstructure des résidus pentadiéniques dans les homo- et copolymères des cis et trans pentadiènes-1,3 avec l'acrylonitrile

The microstructure of diene units was investigated in radical homopolymers of the cis and trans isomers of 1,3-pentadiene and copolymers with acrylonitrile, synthetized in bulk and emulsion. Experiments were carried out by infrared spectroscopy, 100 MHz ¹H-NMR, and 25 MHz ¹³C-NMR studies. No difference between the bulk and emulsion samples was noted. The microstructure of poly(1,3-pentadiene) is practically independent of the cis or trans configuration of the diene monomer and is as follows: 56–59% trans-1,4, 15–17% cis-1,4, 16–20% trans-1,2 7–10% cis-1,2 and 0% 3,4. On the other hand, up to about 30% of incorporated acrylonitrile (10% in the feed), the microstructure of the pentadiene fraction in the copolymers is not affected. This finding suggests that the penultimate unit has very little influence on the polymerization process involving the terminal pentadienly unit. Beyond 10% of acrylonitrile in the feed, the proportions of the structural units were linearly dependent upon the acrylonitrile content: trans-1,4 content increased whereas the amounts of cis-1,4 trans-1,2 and cis-1,2 decreased (except the cis-1,2 fraction, constant in the copolymers from the cis-diene). These results are discussed on the assumption that the microstructure of pentadiene residues is strongly associated with the acrylonitrile comonomer in the feed.     

Vapor-liquid equilibria for polybutadiene and polyisoprene solutions

Vapor-liquid equilibria in binary solutions of hydrocarbons (n-hexane, benzene, toluene, cyclohexane) and chlorinated methanes [carbon tetrachloride (CCl₄), chloroform (CHCl₃), and dichloromethane (CH₂Cl₂)] in polybutadiene (PBD) and polyisoprene have been determined at 23.5°C by using the piezoelectric sorption method. The weight-fraction activity coefficient of solvent (a₁/w₁) in cis-PBD (98% cis-1,4 addition) and random cis-trans-PBD (r-PBD, 34.3% cis-1,4 addition; 54.3% trans-1,4 addition; 11.4% vinyl-1,2 addition) are almost equal for CCI₄, CHCI₃, CH₂CI₂, benzene, and toluene solutions, while the values of a₁/w₁ in n-hexane and cyclohexane solutions in cis-PBD are larger than those in r-PBD solutions. The values of a₁/w₁ for solutions of hydrocarbons and chlorinated methanes in cis-1,4 polyisoprene (95% cis-1,4 addition) have been compared with those for cis-PBD.     

Synthesis and characterization of polymers of 1,4-hexadienes

The homopolymerization of trans-1,4-hexadiene, cis-1,4-hexadiene, and 5-methyl-1,4-hexadiene was investigated with a variety of catalysts. During polymerization, 1,4-hexadienes undergo concurrent isomerization reactions. The nature and extent of isomerization products are influenced by the monomer structure and polymerization conditions. Nuclear magnetic resonance (NMR) and infrared (IR) data show that poly(trans-1,4-hexadiene) and poly(cis-1,4-hexadiene) prepared with a Et₃Al/α-TiCl₃/hexamethylphosphoric triamide catalyst system consist mainly of 1,2-polymerization units arranged in a regular head-to-tail sequence. A 300-MHz proton NMR spectrum shows that the trans-hexadiene polymer is isotactic; it also may be the case for the cis-hexadiene polymer. These polymers are the first examples of uncrosslinked ozone-resistant rubbers containing pendant unsaturation on alternating carbon atoms of the saturated carbon-carbon backbone. Polymerization of the 1,4-hexadienes was also studied with VOCl₃- and β-TiCl₃-based catalysts. Microstructures of the resulting polymers are quite complicated due to significant loss of unsaturation, in contrast to those obtained with the α-TiCl₃-based catalyst. In agreement with the literature, there was no discernible monomer isomerization with the VOCl₃ catalyst system.     

Computational Study of Metathesis Degradation of Rubber, 3. Distribution of Cyclic and Linear Oligomers via Intermolecular Degradation of cis‐Poly(butadiene)

The molecular modeling of the product distributions for the intermolecular metathesis degradation of cis‐poly(butadiene) (cis‐PB) in the presence of ethylene as chain‐transfer agent (CTA) at 298.15 K using the B3LYP/6‐31G (d, p) level of theory reveals that chain–ring and chain‐chain equilibria are shifted toward the formation of 1,5‐hexadiene. The amount of cyclic oligomers at equilibrium with linear molecules is negligible. The α,ω‐vinyl‐terminated butadiene oligomers–1,5‐hexadiene equilibrium constant depends on the cis/trans isomer ratio in linear butadiene molecules. While the concentration of 1,5‐hexadiene at equilibrium with cis‐butadiene oligomers is 86 mol‐%, this value for trans‐butadiene oligomers corresponds to 50 mol‐% of 1,5‐hexadiene. The results of calculations are in reasonable agreement with recent experimental data on the intermolecular metathesis of 1,4‐cis‐PB with ethylene using a well‐defined ruthenium alkylidene catalyst. The calculations predict that cis‐butene as a CTA is more efficient in the metathesis depolymerization of cis‐PB compared with ethylene.     

Copolymerization of dienes with neodymium tricarboxylate-based catalysts and cis-polymerization mechanism of dienes

It was found that poly(butadiene), poly(isoprene), and poly(2,3-dimethylbutadiene) with high cis-1,4 content were obtained with Nd(OCOR)₃–(i-Bu)₃Al–Et₂AlCl catalysts (R = CF₃, CCl₃, CHCl₂, CH₂Cl, CH₃) in hexane at 50°C [cis-1,4 content: poly(BD), > 98%; poly(IP), ≥ 96%; poly(DMBD), ≥ 94%]. Copolymerization of IP and styrene (St) was carried out at various monomer feed ratios to evaluate the monomer reactivity ratio and cis-1,4 content of the diene unit and then to elucidate the cis-1,4 polymerization mechanism of IP. The cis-1,4 content of the IP unit in the copolymers decreased with increasing St content in the copolymers. The cis-1,4 polymerization was disturbed by incorporating St unit in the copolymers, since the penultimate St unit hardly coordinates to the neodymium metal, resulting in a decrease of the cis-1,4 content in the copolymers. That is, the cis-1,4 polymerization of IP is suggested to be controlled by a back-biting coordination of the penultimate diene unit. On the other hand, in the case of poly(BD-co-IP) and poly(BD-co-DMBD), the cis-1,4 content of the BD, IP, and DMBD units in the copolymers was almost constant (cis: 94–98%), irrespective of the monomer feed ratios and polymerization temperature. Consequently, the penultimate IP and DMBD units favorably control the terminal BD, IP, or DMBD unit to the cis-1,4 configuration through the back-biting coordination. For the monomer reactivity ratios, a clear difference was observed in each system: r_BD = 1.22, r_IP = 1.14; r_BD = 40.9, r_DMBD = 0.15. Low polymerizability of DMBD was mainly ascribed to the steric effect of the methyl substituents. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1707–1716, 1998     

Carbon-13 NMR of polybutadiene

By using the carbon-13 NMR technique, it is shown that there are no cis-1,4–trans-1,4 linkages in a n-BuLi-catalyzed polybutadiene. The polymer consists of “blocks” of cis-1,4 units and trans-1,4 units separated by isolated vinyl units. Preliminary evidence suggests this might also be true for other types of 1,3-diene polymerization. Some of the implications of this finding on the mechanism of polymerization are discussed. Tacticity triad distributions are readily determined in polybutadienes with high 1,2 addition contents.     

~(13)C-NMR STUDY ON THE EQUIBINARY (cis-1,4;1,2) POLYBUTADIENE POLYMERIZED WITH IRON CATALYST

The (cis-1,4 and 1,2) polybutadiene polymerized with iron catalyst was investigated by ~(13)C-NMR. Assignments have been made on the spectra for all peaks of the aliphatic and olefinic carbons using chemical shift corrective terms together with Furukawa parameters. The relative intensities of peaks were calculated from the Bernoulli distribution of cis-1,4 and 1,2 units.Quantification of cis-1,4 and 1,2 contents, sequence distribution, alternation pattern of cis-1,4 and 1,2 units, and the chain propagation mechanism were discussed as a result of the detailed study of the spectra.     

Quantitative estimation of trans-1,4 and cis-1,4 isomers in polychloroprene by high-resolution NMR

In the ¹H-NMR spectrum of polychloroprene dissolved in C₆D₆, the ?CH proton signal was separated into two triplet peaks. These triplet signals were assigned to the ?CH proton in the trans-1,4 and cis-1,4 isomers by measurement of ¹H-NMR spectra of 3-chloro-1-butene and a mixture of trans- and cis-2-chloro-2-butene as model compounds for the 1,2, trans-1,4 and cis-1,4 isomers. In ¹H-NMR spectra (220 Mcps) of polychloroprene dissolved in C₆D₆, two triplet signals were separated completely from which the relative concentrations of trans-1,4 and cis-1,4 isomers could be obtained quantitatively.     

3-D frameworks assembled by lanthanide dimers with 1,4-cyclohexanedicarboxylic acid and 1,10-phenanthroline via hydrogen bonds and π–π stacking interactions

Two complexes [Ln(e,a-cis-1,4-chdc)(e,a-cis-1,4-Hchdc)(phen)(H₂O)]₂?10H₂O (Ln = Eu, 1; Tb, 2, 1,4-H₂chdc = 1,4-cyclohexanedicarboxylic acid; phen = 1,10-phenanthroline) have been synthesized and structurally characterized by single-crystal X-ray diffraction. Both complexes are doubly e,a-cis-1,4-chdc-bridged dimers. The e,a-cis-1,4-Hchdc, phen, and water molecules bond to Ln³⁺, forming nine-coordinate complexes. 3-D supramolecular frameworks are constructed by hydrogen bonds and π–π stacking interactions. Luminescence spectra exhibit the ⁵D₀ → ⁷F _J (J = 0–4) and ⁵D₄ → ⁷F _J (J = 6–3) transitions of Eu³⁺ for 1 and Tb³⁺ ion for 2, respectively.     

Pyrolysis of polyisoprenes. I. Differentiation between natural and synthetic cis-1,4-polyisoprenes

Two methods of differentiating between natural rubber and synthetic cis-1,4-polyisoprenes have been examined. Both techniques depend on the presence of Ziegler-Natta catalyst residues in the synthetic polymers. The major pyrolysis product of cis-1,4-polyisoprenes at 350°C is 1-methyl-4-(1-methylethenyl)cyclohexene. This can undergo disproportionation to yield 1-methyl-4-(1-methylethyl)benzene and methyl-(1-methylethyl)cyclohexenes. It is this disproportionation reaction, catalyzed by Ziegler-Natta catalyst residues or by carbon black, that is responsible for the different product ratios obtained on pyrolysis of natural rubber and Ziegler-Natta catalyzed cis-1,4-polyisoprenes. Lithium alkyl-polymerized polyisoprenes undergo this secondary disproportionation reaction only in the presence of carbon black. Derivative thermogravimetric traces of black-filled sulfur vulcanizates of natural rubber and synthetic polyisoprenes are significantly different because polymerization catalyst residues promote cyclization of the polymer.     

13C-NMR spectra of cis-polymyrcene and cis-polyfarnesene

Homopolymers of myrcene and farnesene were prepared anionically in pure cyclohexane. The microstructure, determined from an analysis of the ¹³C-NMR spectrum and spin-lattice relaxation times, indicates the polymers are at least 85% cis-1,4, 10% cis-3,4, and under 3% trans-1,4.     

Stereochemistry of Dehydrogenation of 1,4,-Cyclohexadiene with 2,3-Dichloro-5,6-dicyano-p-benzoquinone

cis- and trans-(3,6-D₂)-1,4-cyclohexadienes 1a and 1b have been synthesized from cis-3,4-dichlorocyclobutene (5). Aromatization to benzene with DDQ is cis-stereospecific with an uncertainty of 5%. This result is discussed in relation to concerted or stepwise mechanisms for aromatization of 1,4-dihydroaromatics with 2,3-dichloro-5,6-dicyano-p-benzoquinone (DDQ).     

Filler–polymer interactions in both silica and carbon black‐filled styrene–butadiene rubber compounds

Bound rubber in a filled rubber compound is formed by physical adsorption and chemisorption between the rubber and the filler. Styrene–butadiene rubber (SBR) is composed of four components of styrene, cis‐1,4‐, trans‐1,4‐, and 1,2‐units. Filler–polymer interactions in both silica and carbon black‐filled SBR compounds were studied by analyzing microstructures of the bound rubbers with pyrolysis‐gas chromatography. Differences in the filler–polymer interactions of the styrene, cis‐1,4‐, trans‐1,4‐, and 1,2‐units were investigated. The filler–polymer interactions of the butadiene units were found to be stronger than that of the styrene unit. The interactions of the cis‐1,4‐ and trans‐1,4‐units were stronger with carbon black than with silica, whereas the 1,2‐unit interacted more strongly with silica than with carbon black. © 2001 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 439–445, 2001     

Poly(1,4‐cyclohexylenedimethylene 1,4‐cyclohexanedicarboxylate): Influence of stereochemistry of 1,4‐cyclohexylene units on the thermal properties

A series of poly(1,4‐cyclohexylenedimethylene 1,4‐cyclohexanedicarboxylate) (PCCD) samples, characterized by different cis/trans ratio of the 1,4‐cyclohexanedicarbonyl unit, have been synthesized and analyzed by thermogravimetry (TGA), calorimetry (DSC), and X‐ray diffraction (WAXD). The thermal stability results are good and are not affected by the stereochemistry of the 1,4‐cyclohexylene units. On the other hand, the thermal transitions are notably influenced by the cis/trans content. With the increment of the trans content the polymer changes from completely amorphous to semicrystalline material. T_g, T_m, and crystallinity increase. These results suggest that the trans configuration induces a better chain packing and higher symmetry, improving the crystallizability of the samples. The effect of the molecular structure on the thermal properties is analyzed by using a statistical approach. From the effective correlations found between stereochemistry of the C₆ rings and transition temperatures it is possible to extrapolate that the configuration of 1,4‐cyclohexylene ring deriving from 1,4‐cyclohexanedicarboxylic acid or dimethyl 1,4‐cyclohexanedicarboxylate results to be the main element responsible for the thermal properties. This is due to the high rigidity of the 1,4‐cyclohexanedicarbonyl unit with respect to 1,4‐cyclohexanedimethyleneoxy unit, deriving from the diol. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 619–630, 2008     

Computational study of sulfoxides of thiacyclohexane, 4‐silathiacyclohexane, 4‐fluoro‐4‐silathiacyclohexane,and 4,4‐difluoro‐4‐silathiacyclohexane: Relative energies of conformations and sulfinyl oxygen stabilized pentacoordinate silicon in boat and twist structures

Second‐order Møller‐Plesset theory (MP2) has been used to calculate the equilibrium geometries and relative energies of the chair, 1,4‐twist, 2,5‐twist, 1,4‐boat, and 2,5‐boat conformations of thiacyclohexane 1‐oxide (tetrahydro‐2H‐thiopyran 1‐oxide), 4‐silathiacyclohexane 1‐oxide, cis‐ and trans‐4‐fluoro‐4‐silathiacyclohexane 1‐oxide, and 4,4‐difluoro‐4‐silathiacyclohexane 1‐oxide. At the MP2/6‐311+G(d,p) level of theory, the chair conformer of axial thiacyclohexane 1‐oxide is 0.99, 5.61, 5.91, 8.57, and 7.43 kcal/mol more stable (ΔE) than its respective equatorial chair, 1,4‐twist, and 2,5‐twist conformers and 1,4‐boat and 2,5‐boat transition states. The chair conformer of equatorial thiacyclohexane 1‐oxide is 4.62, 6.31, 7.56, and 7.26 kcal/mol more stable (ΔE) than its respective 1,4‐twist and 2,5‐twist conformers and 1,4‐boat and 2,5‐boat transition states. The chair conformer of axial 4‐silathiacyclohexane 1‐oxide is 1.79, 4.26, 3.85, and 5.71 kcal/mol more stable (ΔE) than its respective equatorial chair, 1,4‐twist, and 2,5‐twist conformers and 2,5‐boat transition state. The 2,5‐twist conformer of axial 4‐silathiacyclohexane 1‐oxide is stabilized by a transannular interaction between the sulfinyl oxygen and silicon, to give trigonal bipyramidal geometry at silicon. The chair conformer of equatorial 4‐silathiacyclohexane 1‐oxide is 2.47, 7.90, and 8.09 kcal/mol more stable (ΔE) than its respective 1,4‐twist, and 2,5‐twist conformers and 2,5‐boat transition state. The chair conformer of axial cis‐4‐fluoro‐4‐silathiacyclohexane 1‐oxide is 4.18 and 5.70 kcal/mol more stable than its 1,4‐twist conformer and 2,5‐boat transition state and 1.51 kcal/mol more stable than the chair conformer of equatorial cis‐4‐fluoro‐4‐silathiacyclohexane 1‐oxide. The chair conformer of axial trans‐4‐fluoro‐4‐silathiacyclohexane 1‐oxide is 5.02 and 6.11 kcal/mol more stable than its respective 1,4‐twist conformer and 2,5‐boat transition state, but is less stable than its 2,5‐twist conformer (ΔE = ?1.77 kcal/mol) and 1,4‐boat transition state (ΔE = ?1.65 kcal/mol). The 2,5‐twist conformer and 1,4‐boat conformer of axial trans‐4‐fluoro‐4‐silathiacyclohexane 1‐oxide are stabilized by intramolecular coordination of the sulfinyl oxygen with silicon that results in trigonal bipyramidal geometry at silicon. The chair conformer of axial 4,4‐difluoro‐4‐silathiacyclohexane 1‐oxide is 3.02, 5.16, 0.90, and 6.21 kcal/mol more stable (ΔE) than its respective equatorial chair, 1,4‐twist, and 1,4‐boat conformers and 2,5‐boat transition state. The 1,4‐boat conformer of axial 4,4‐difluoro‐4‐silathiacyclohexane 1‐oxide is stabilized by a transannular coordination of the sulfinyl oxygen with silicon that results in a trigonal bipyramidal geometry at silicon. The relative energies of the conformers and transition states are discussed in terms of hyperconjugation, orbital interactions, nonbonded interactions, and intramolecular sulfinyl oxygen–silicon coordination. © 2004 Wiley Periodicals, Inc. Int J Quantum Chem, 2005     

SYNTHESIS AND CHARACTERIZATION OF A SERIES OF LIPOPHILIC CISPLATIN ANALOGS WITH CIS-1,4-DIAMINOCYCLOHEXANE AS NONLEAVING AMINE LIGAND

Abstract

A series of lipophilic platinum(II) complexes of the type [Pt(cis-1,4-DACH)L₂] (where cis-1,4-DACH = cis-1,4-diaminocyclohexane and L = acetate, propionate, butyrate, valerate, hexanoate, heptanoate, octanoate, 2,2′-dimethyloctanoate, nonanoate, decanoate, undecanoate, laureate, tridecanoate, myristate, pentadecanoate, palmitate, heptadecanoate, stearate, nonadecanoate, or eicosanoate) has been synthesized and characterized by elemental analysis and by infrared, ¹³C, and ¹⁹⁵Pt nuclear magnetic resonance spectroscopic techniques.