Cure kinetics of epoxy-amine resins used in the restoration of works of art from glass or ceramic

The cure kinetics of two epoxy/amine resins, Araldite 2020 and AY103-HY956 widely used as adhesives in the restoration of works of art from glass or ceramic was investigated using FTIR spectroscopy. These resins are two-part adhesives, consisting of a resin - A, based on a diglycidyl ether of bisphenol A, and a hardener - B which is either a cycloaliphatic amine (isophorone diamine) for Araldite 2020, or a mixture of three aliphatic amines in HY956. The study was based on the collection of IR spectra, in the middle range (4000-600 cm⁻¹), of mixtures of resin and hardener at different proportions and isothermal temperatures (22-70 °C) as a function of curing time. A kinetic model was employed to simulate the experimental data using two kinetic rate constants. Diffusion control was incorporated to describe the cure behaviour at high degrees of conversion. From fitting to experimental data the kinetic and diffusional parameters were estimated, together with the activation energies of the kinetic and autocatalytic rate constants. It was found that higher degrees of curing are obtained at higher temperatures and increased amounts of hardener. Differences in the performance of the two adhesives are explained based on the type of the amines used as hardener.     

NIR spectroscopy of jarosites

Near-infrared (NIR) spectroscopy has been used to analyse a suite of synthesised jarosites of formula Mn(Fe3+)6(SO4)4(OH)12 where M is K, Na, Ag, Pb, NH4+ and H3O+. Whilst the spectra of the jarosites show a common pattern, differences in the spectra are observed which enable the minerals to be distinguished. The NIR bands in the 6300-7000 cm-1 region are attributed to the first fundamental overtone of the infrared and Raman hydroxyl stretching vibrations. The NIR spectrum of the ammonium-jarosite shows additional bands at 6460 and 6143 cm-1, attributed to the first fundamental overtones of NH stretching vibrations. A set of bands are observed in the 4700-5500 cm-1 region which are assigned to combination bands of the hydroxyl stretching and deformation vibrations. The ammonium-jarosite shows additional bands at 4730 and 4621 cm-1, attributed to the combination of NH stretching and bending vibrations. NIR spectroscopy has the ability to distinguish between the jarosite minerals even when the formula of the minerals is closely related. The NIR spectroscopic technique has great potential as a mineral exploratory tool on planets and in particular Mars.     

Near-infrared spectroscopy of natural alunites

Near-infrared spectroscopy (NIR) has been used to analyse alunites of formula K(Al3+)6(SO4)4(OH)12. Whilst the spectra of the alunites shows a common pattern differences in the spectra are observed which enable the minerals to be distinguished. These differences are attributed to subtle variations in alunite composition. The NIR bands in the 6300-7000 cm(-1) region are attributed to the first fundamental overtone of both the infrared and Raman hydroxyl stretching vibrations. A set of bands are observed in the 4700-5500 cm(-1) region which are assigned to combination bands of the hydroxyl stretching and deformation vibrations. NIR spectroscopy has the ability to distinguish between the alunite minerals even when the formula of the minerals is closely related. The NIR spectroscopic technique has great potential as a mineral exploratory tool on planets and in particular Mars.     

Spectroscopic study of overtone and combination bands in aliphatic aldehydes

Overtone spectra of C–H stretching vibrations of formaldehyde, acetaldehyde and n-butyraldehyde have been studied in liquid phase using conventional absorption and thermal lens techniques. The overtone bands up to Δν = 4 have been monitored using the conventional IR and NIR techniques and the band involving Δν = 7 of the C–H stretching vibration with thermal lens technique. The vibrational frequencies and the anharmonicity constants for C–H stretching vibrations of the methyl as well as of the aldehyde groups for all the three molecules have been determined using these data. We have also calculated the vibrational frequencies of fundamental bands and charge distribution on carbon and hydrogen atoms using ab initio methods and the results are compared with the experimental data.     

Ambiguity in Assignment of Near Infrared Vibrational Bands for Polymerisation Monitoring of Epoxy System

The curing process of epoxy affects the chemical structure of the final network so mechanical and physical properties of the polymeric matrix for a composite may be modified according to the polymerisation conditions. This paper describes the ambiguity in assignment of reference bands to follow the cure of poly-epoxy reactive systems using a laboratory-made system which allows the coupling of dielectric analysis and Fourier Transform Near Infrared Spectroscopy (FTNIR). The dielectric measurements were obtained using interdigitated electrode. In situ monitoring of extent of reaction was carried out from room temperature up to 160 °C using fibre-optic FTNIR spectroscopy. For the DGEBA/MCDEA system the epoxy band at 6060 cm⁻¹ was chosen in preference to the band at 4530 cm⁻¹ as representative of the epoxy function evolution during polymerisation because a small unknown peak probably due to the hardener appears in the 4530 cm⁻¹ region. The bands at 4620 and 4680 cm⁻¹ assigned to aromatic combination bands and widely used as reference bands are not unique for this formulation hence the band at 5980 cm⁻¹ is used as reference. The Principal Components Analysis (PCA) shows clearly also that the bands at 4620 and 4680 cm⁻¹ vary during the polymerisation. Surprisingly, the band at 4530 cm⁻¹ is equivalent to the one at 6060 cm⁻¹ to calculate the conversion rate. It is probably due to the fact that the hardener band near 4530 cm⁻¹ follows the same behaviour as the epoxy band at 4530 cm⁻¹.     

Study of the reaction mechanism of the copper chelate with DGEBA using DSC

The reaction mechanism of metal-containing and complex compound with epoxy oligomer of diglycidyl ether of bisphenol A (DGEBA) was studied using dynamic DSC technique. It is shown that cure reaction of the epoxy oligomers with copper acetate proceeds at two stages: through coordination of cation with the epoxy group, and through ionic polymerization at high temperatures. Mechanism of curing of DGEBA with copper chelate depends on equilibrium process of dissociation of the chelate which, in turn, depends not only on temperature of curing but also on concentration of the hardener. At the dissociation temperature of the hardener, polymerization proceeds according to ionic mechanism. Hardening of the epoxy oligomers due to interaction of epoxy groups with unconnected amine groups predominate at higher temperatures or at higher concentrations of the hardener. At low temperatures and small concentrations of the hardener, polymerization proceeds according to catalytic ionic mechanism. This revised version was published online in July 2006 with corrections to the Cover Date.     

Evaluation of furfurylamines as curing agents for epoxy resins

Epoxy resin adhesives are widely used because of their strength, versatility, and ability to bond a variety of substrates. Furfurylamines represent a potential, new class of epoxy curing agents. Furfuryl amine (FA), tetrahydrofurfuryl amine (THFA), and 5,5′-methylenebis-2-furanmethanamine (DFA) were studied as possible epoxy curing agents. The utility of FA and THFA are limited by their volatility at the temperatures needed to effect cure of diglycidyl-ether of bisphenol A (DGEBA) based epoxy resins. DFA is a very effective epoxy curing agent with the ability to cure DGEBA at rates similar to that of standard epoxy curing agents such as liethylenetriamine.     

苯基二氨三嗪-甲醛树脂高温固化过程的红外光谱研究

本文通过不同平均加成度的A阶苯基二是三嗉甲醛树脂的红外光谱分析,对其红外吸收峰的归属进行了讨论。应用高温红外光谱和差谱技术对两种树脂样品的交联行为进行跟踪观察,由的红外吸收变化和反应体系中甲醛的检测推论了树脂的热固化反应。     

Hydrogen bonding effects on the wavenumbers and absorption intensities of the OH fundamental and the first, second, and third overtones of phenol and 2,6-dihalogenated phenols studied by visible/near-infrared/infrared spectroscopy

Visible, near-infrared (NIR) and IR spectra in the 15600-2500 cm(-1) region were measured for phenol and 2,6-difluorophenol, 2,6-dichlorophenol, and 2,6-dibromophenol in n-hexane, CCl(4), CHCl(3) and CH(2)Cl(2) to study hydrogen bonding effects and solvent dependences of wavenumbers and absorption intensities of the fundamental and the first, second, and third overtones of OH stretching vibrations. A band shift of the OH stretching vibrations from a gas state to a solution state (solvent shift) was plotted versus vibrational quantum number (v = 0, 1, 2 and 3), and it was found that there is a linear relation between the solvent shift and the vibrational quantum number. The slope of solvent shift decreases in the order of phenol, 2,6-difluorophenol and 2,6-dichlorophenol. For all of the solute molecules, the slope becomes larger with the increase in the dielectric constant of the solvents. The relative intensities of the OH stretching vibrations of phenol in CCl(4), CHCl(3), and CH(2)Cl(2) against the intensity of the corresponding OH vibration in n-hexane increase in the fundamental and the second overtone but decrease in the first and third overtones; the relative intensities show so-called "parity". The parity is more prominent for phenol that has an intermolecular hydrogen bonding than for 2,6-dihalogenated phenols that have an intramolecular hydrogen bond. These observations suggest that the intermolecular hydrogen bond between the OH group and the Cl atom plays a key role for the parity and that the intermolecular interaction between the solutes and the solvents (solvent effects) does not have a significant role in the parity.     

Effect of acetone on mechanical properties of epoxy used for surface treatment before adhesive bonding

A thin layer of un-cured resin over metal substrates applied by using an acetone-diluted resin solution (without hardener) has been found to be beneficial to strong adhesive bonding. The resin pre-coating (RPC) solution can effectively seal sub-surface micro-cavities and increase the substrate wettability. This study examines possible aftermath effects of the acetone dilution on mechanical properties of epoxy through comparison of samples made from as-received resin and resins diluted once and twice by acetone. RPC can be accepted with confidence in substrate pre-treatments for strong adhesive bonding if no detrimental effect on epoxy properties is observed. Fourier transform infrared spectrum (FTIR) was conducted, showing the spectrogram of the resin previously diluted by acetone was the same as that of as-received resin, i.e. no change in epoxy molecular structures after complete evaporation of acetone. Strength and modulus of elasticity measured by flexural and compressive tests were compared using samples made from as-received resin, and resins diluted once and twice by acetone. Variations among results from the three groups were less than 2%, or negligible, affirming the RPC method can be used for substrate pre-treatments and stronger adhesive bonding.     

Acid treatment for functionalizing polyethylene fiber surfaces for enhanced adhesion to epoxy resins

The utility of high-strength, high-modulus polyethylene fibers in fiber-reinforced composites is limited due to its poor interfacial adhesion to various polymeric matrices. One way to overcome this limitation is to introduce reactive functionalities on the fiber surface capable of covalently bonding to matrix resins. Ultra high-strength polyethylene (UHSPE) fibers were treated with chlorosulfonic acid. The surface acid groups were found to considerably improve the interfacial adhesion between polyethylene fibers and epoxy resins as shown by the microbond test. These surface functionalities were found to improve the fiber wettability, as shown by contact angle measurements using the Wilhelmy balance method. Colorimetric measurements of methylene blue absorption were used to quantify the surface concentrations of the acid groups. It was possible to functionalize the UHSPE fiber surfaces using this method to obtain fibers that formed a stronger adhesive bond with epoxy resins; this was achievable without sacrificing other fiber mechanical properties.     

Influence of the type of epoxy hardener on the structure and properties of interpenetrated vinyl ester/epoxy resins

The morphology–toughness relationship of vinyl ester/cycloaliphatic epoxy hybrid resins of interpenetrating network (IPN) structures was studied as a function of the epoxy hardening. The epoxy was crosslinked via polyaddition reactions (with aliphatic and cycloaliphatic diamines), cationic homopolymerization (via a boron trifluoride complex), and maleic anhydride. Maleic anhydride worked as a dual‐phase crosslinking agent by favoring the formation of a grafted IPN structure between the vinyl ester and epoxy. The type of epoxy hardener strongly affected the IPN morphology and toughness. The toughness was assessed by linear elastic fracture mechanics, which determined the fracture toughness and energy. The more compact the IPN structure was, the lower the fracture energy was of the interpenetrated vinyl ester/epoxy formulations. This resulted in the following toughness ranking: aliphatic diamine > cycloaliphatic diamine ≥ boron trifluoride complex > maleic anhydride. For IPN characterization, the width of the entangling bands and the surface roughness parameters were considered. Their values were deduced from atomic force microscopy scans taken on ion‐etched surfaces. More compact, less rough IPN‐structured resins possessed lower toughness parameters than less compact, rougher structured ones. The latter were less compatible according to dynamic mechanical thermal and thermogravimetric analyses. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5471–5481, 2004     

Curing of an epoxy resin modified with poly(methylmethacrylate) monitored by simultaneous dielectric/near infrared spectroscopies

Simultaneous dielectric and near infrared measurements have been performed in “real-time” to follow polymerisation reactions on blends of a diglycidyl ether of bisphenol-A epoxy resin with 4,4^′-diaminodiphenylmethane hardener and different amounts of poly(methylmethacrylate) as modifier. The effect of the modifier amount on the polymerisation reactions has been studied, as well as that of the curing temperature. Epoxy and amine conversions have been followed by near infrared spectroscopy (NIR), while changes in molecular mobility in the reaction mixture have been analysed by dielectric relaxation spectroscopy (DRS). Evolutions of ionic conductivity and α-relaxation have been analysed and vitrification times have been obtained. The relaxational behaviour has been analysed through curing in the frequency domain, being the change of the main relaxation indicative of the cure reaction advancement. DRS data are also presented as complex impedance Z(ω). Vitrification times, obtained by dielectrometry have been compared with those obtained by rheological measurements and gelation times obtained by NIR have been compared with those obtained by solvent extraction.     

Photo-oxidative stability of electron beam and UV cured acrylated epoxy and urethane acrylate resin films

The post-cured photo-oxidative stability of urethane and bisphenol-A epoxyacrylate resins in mixed compositions with triacrylate and amine diacrylate resins are examined using UV and reflectance infra-red absorption spectroscopic techniques. Overall, by measuring the growth in hydroxyl absorption at 3400 cm⁻¹, electron-beam cured resin films are more photostable than UV curedfilms, indicating the high photo-activity of residual photoinitiator in the latter case. Regarding the UV cured systems benzophenone is found to be a more photo-active residual photoinitiator than the benzoyl ester photofragmenting types. Films containing the amine diacrylate resin are more photostable than those containing the triacrylate resin. This stabilising effect is associated with the oxygen and radical scavenging ability of the terminal amine groups. Photo-yellowing, as measured by the growth in an absorption band at 280 nm, is observed only in resin films containing the amine diacrylate resin and is associated with the formation of unsaturated carbonyl groups. The latter are, however, photobleached on prolonged irradiation whereas with resins containing the bisphenol-A epoxy acrylate resin, a longer term photo-yellowing is observed due to oxidation of the bisphenol-A to give stilbene-quinone products.     

Influence of intramolecular hydrogen bonding on OH-stretching overtone intensities and band positions in peroxyacetic acid

Vapor phase absorption spectra and integrated band intensities of the OH stretching fundamental as well as first and second overtones (2ν(OH) and 3ν(OH)) in peroxyacetic acid (PAA) have been measured using a combination of FT-IR and photoacoustic spectroscopy. In addition, ab initio calculations have been carried out to examine the low energy stable conformers of the molecule. Spectral assignment of the primary features appearing in the region of the 2ν(OH) and 3ν(OH) overtone bands are made with the aid of isotopic substitution and anharmonic vibrational frequency calculations carried out at the MP2/aug-cc-pVDZ level. Apart from features associated with the zeroth-order OH stretch, the overtone spectra are dominated by features assigned to combination bands composed of the respective OH stretching overtone and vibrations involving the collective motion of several atoms in the molecule resulting from excitation of the internal hydrogen bonding coordinate. Integrated absorption cross section measurements reveal that internal hydrogen bonding, the strength of which is estimated to be ～20 kJ/mol in PAA, does not result in a enhanced oscillator strength for the OH stretching fundamental of the molecule, as is often expected for hydrogen bonded systems, but does cause a precipitous drop in the oscillator strength of its 2ν(OH) and 3ν(OH) overtone bands, reducing them, respectively, by a factor of 165 and 7020 relative to the OH stretching fundamental.     

Spectra and integrated band intensities of the low order OH stretching overtones in peroxyformic acid: an atmospheric molecule with prototypical intramolecular hydrogen bonding

The gas phase spectra of several vibrational bands of peroxyformic acid (PFA), an atmospheric molecule exhibiting intramolecular hydrogen bonding, are presented. In the fundamental region, Fourier transform infrared (FT-IR) spectroscopy is used to probe the C-O, O-H and C-H stretching vibrations, while in the region of the first and second OH-stretching overtones (2ν(OH) and 3ν(OH)) photoacoustic spectroscopy is used. Integrated absorption cross sections for the PFA vibrational bands are determined by comparing their respective peak areas with that for the OH-stretching bands of n-propanol for which the absorption cross section is known. The measured integrated intensities of the OH stretching bands are then compared with a local mode model using a one-dimensional dipole moment function in conjunction with the OH stretching potential computed at both the MP2/aug-cc-pVDZ and CCSD(T)/aug-cc-pVDZ levels. The data allow us to investigate changes in the OH stretch band position and intensity as a function of overtone order arising from the influence of hydrogen bonding. Furthermore, calculations at the MP2/aug-cc-pVDZ level show that there are three stable conformers of PFA with relative energies of 0, 13.54, and 13.76 kJ/mol, respectively. In the room temperature spectra, however, we see evidence for transitions from only the lowest energy conformer. The geometrical parameters and vibrational frequencies of the most stable conformer are presented.     

Cure of epoxy resins with cyanoacetamides

Cyanoacetamides are a novel class of curing agents for epoxy resins. Since reaction products of epoxy compounds with cyanoacetamides have not yet been described, we investigated the reaction of phenyl-glycidylether (PGE) and N-isobutylcyanoacetamide (NICA) under the conditions of the epoxy cure (120–150°C). Twenty-two fractions of the reaction product have been separated by preparative TLC and characterized by FD and MS mass spectroscopy. The structures of 10 reaction product have been elucidated by MS, NMR, and IR techniques. They belong to the classes of cyclic urethanes, spiro-dilactones, cyclo-oxa-1-hepten-4-one-2, pyrimidones, aminocrotononitrile, and tertiary amine. This complex model reaction mixture does not enable us to propose a curing mechanism. However practical cure of Bisphenol A diglycidylether (BADGE) yields clear and tough solids with a glass transition temperature up to 200°C, good mechanical strength, and high adhesion to metal surface. Cyanoacetamides are latent hardeners requiring a curing initiator. Since N-4-chlorophenyl-N′-dimethylurea is a latent initiator, liquid, homogeneous, storage stable “one shot” systems can be formulated which harden quickly above 120°C. Heat aging properties of cured specimens are reported. A series of novel liquid, resinous, and crystalline cyanoacetamides and their potential as curing agent are described.     

Curing reaction of biphenyl epoxy resin with different phenolic functional hardeners

The investigation of cure kinetics and relationships between glass transition temperature and conversion of biphenyl epoxy resin (4,4′-diglycidyloxy-3,3′,5,5′-tetramethyl biphenyl) with different phenolic hardeners was performed by differential scanning calorimeter using an isothermal approach over the temperature range 120–150°C. All kinetic parameters of the curing reaction including the reaction order, activation energy, and rate constant were calculated and reported. The results indicate that the curing reaction of formulations using xylok and dicyclopentadiene type phenolic resins (DCPDP) as hardeners proceeds through a first-order kinetic mechanism, whereas the curing reaction of formulations using phenol novolac as a hardener goes through an autocatalytic kinetic mechanism. The differences of curing reaction with the change of hardener in biphenyl epoxy resin systems were explained with the relationships between T_g and reaction conversion using the DiBenedetto equation. A detailed cure mechanism in biphenyl-type epoxy resin with the different hardeners has been suggested. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 773–783, 1998     

Curing of liquid crystalline epoxy resins with a biguanide

This work extends the authors' investigations on liquid crystalline epoxy resins prepared from diglycidyl ether of 4,4′-dihydroxybiphenyl (DGE-DHBP) and aliphatic dicarboxylic compounds (ADC) or difunctional aromatic compounds. Syntheses and properties of these liquid crystalline epoxy resins are described elsewhere. In this paper a study on the curing reaction of the above mentioned liquid crystalline epoxy resins is presented. Ortho-tolylbiguanide was applied as the curing agent. The curing reactions were investigated by differential scanning calorimetry, microscopic observations and IR spectroscopy. Depending upon the temperature program of curing, it was possible to obtain polymeric networks with liquid crystalline order. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2739–2745, 1997