A lotus root-like porous nanocomposite polymer electrolyte

A lotus root-like porous nanocomposite polymer electrolyte (NCPE) based on poly(vinylidene difluoride-co-hexafluoropropylene) [P(VDF-HFP)] copolymer and TiO₂ nanoparticles was easily prepared by a non-solvent induced phase separation (NIPS) process. The formation mechanism of the lotus root-like porous structure is explained by a qualitative ternary phase diagram. The resulting NCPE had a high ionic conductivity up to 1.21 × 10⁻³ S cm⁻¹ at room temperature, and exhibited a high electrochemical stability potential of 5.52 V (vs. Li/Li⁺), lithium ion transference number of 0.65 and 22.89 kJ mol⁻¹ for the apparent activation energy for transportation of ions. It is of great potential application in polymer lithium ion batteries.     

A novel process to prepare porous membranes comprising SnO2 nanoparticles and P(MMA-AN) as polymer electrolyte

We have successfully developed a new process to prepare porous poly(methyl methacrylate-co-acrylonitrile) (P(MMA-AN)) copolymer based gel electrolyte. The porous structure in the polymer matrix is achieved by adding SnO₂ nanoparticles which are mostly used as gas sensor materials. The quasi-aromatic solvent, NMP, has an electron-repulsion effect with the space charge layer on the surface of SnO₂ nanoparticles and forms a special gas–liquid phase interface. Once the cast polymer solution is stored at an elevated temperature to evaporate the solvent, gas–liquid phase separation happens and spherical pores are obtained. The ionic conductivity at room temperature of the prepared gel polymer electrolyte based on the porous membrane is as high as 1.54 × 10⁻³ S cm⁻¹ with the electrochemical stability up to 5.10 V (vs. Li/Li⁺). This method presents another promising way to prepare porous polymer electrolyte for practical use.     

Electrochemical properties of liquid electrolyte added quasi-solid state TiO2 dye-sensitized solar cells

In this study a process has been introduced to replace traditional liquid or solid electrolyte coatings on dye-sensitized photoelectrode in solar cells. This process has more efficient diffusion of electrolyte, hence higher sensitivity. Better interfacial contact between polymer electrolyte and TiO₂ photoelectrode had improved electrochemical response and ionic conductivity of cell. Conductivity of this electrode was 9.33 × 10⁻³ S cm⁻¹ (at room temperature), which is much higher than the using traditional process for addition of electrolytes. It has 0.68 V open-circuit voltage and 3.19 mA cm⁻² short-circuit current density. Energy conversion efficiency of this cell was about 37% higher than the cell developed with traditional processes under constant light intensity (45 mW cm⁻²).     

Preparation of porous polymer electrolyte by a microwave assisted effervescent disintegrable reaction

Porous polymer membranes with sub-micrometer pores were successfully prepared by a novel microwave assisted effervescent disintegrable reaction. The fine connected porous structure was obtained by promoting effervescent disintegrable reaction between citric acid and sodium bicarbonate due to the assistance of microwave. The ionic conductivity of the prepared gelled polymer electrolyte is up to 1.17 × 10^?3 S cm^?1 and electrochemical window 4.5 V. This method provides a convenient route to prepare porous polymer electrolyte, which will greatly promote the practical application of porous polymer electrolytes.     

Plastic–polymer composite electrolytes: Novel soft matter electrolytes for rechargeable lithium batteries

We present here a soft matter solid composite electrolyte obtained by inclusion of a polymer in a semi-solid organic plastic lithium salt electrolyte. Compared to lithium bis-trifluoromethanesulfonimide-succinonitrile (LiTFSI-SN), the (100 − x)%-[LiTFSI-SN]: x%-P (P: polyacrylonitrile (PAN), polyethylene oxide (PEO), polyethylene glycol dimethyl ether (PEG)) composites possess higher ambient temperature ionic conductivity, higher mechanical strength and wider electrochemical window. At 25 °C, ionic conductivity of 95%-[0.4 M LiTFSI-SN]: 5%-PAN was 1.3 × 10⁻³ Ω⁻¹ cm⁻¹ which was twice that of LiTFSI-SN. The Young’s modulus (Y) increased from Y → 0 for LiTFSI-SN to a maximum ∼1.0 MPa for (100 − x)%-[0.4 M LiTFSI-SN]: x%-PAN samples. The electrochemical voltage window for composites was approximately 5 V (Li/Li⁺). Excellent galvanostatic charge/discharge cycling performance was obtained with composite electrolytes in Li|LiFePO₄ cells without any separator.     

Amorphous silicon thin films as a high capacity anodes for Li-ion batteries in ionic liquid electrolytes

High lithiation capacity at low red-ox potentials in combination with good safety characteristics makes amorphous Si as a very promising anode material for rechargeable Li batteries.Thin film silicon electrodes were prepared by DC magnetron sputtering of silicon on stainless steel substrates. Their behavior as Li insertion/extraction electrodes was studied by voltammetry and chronopotentiometry at room temperature in the ionic liquid (IL) 1-methyl-1-propylpiperidinium bis(trifluoromethylsuphonil)imide containing 1 M Li bis(trifluoromethylsuphonil)imide. Li/Si cells containing this electrolyte showed good performance with a stable Si electrodes capacity of about 3000 mA h g⁻¹ and a relatively low irreversible capacity. Preliminary results on cycling Si–LiCoO₂ cells using this IL electrolyte are also presented.     

Polyacrylamide-lithium chloride polymer electrolyte and its applications in electrochemical capacitors

A neutral polymer electrolyte containing lithium chloride (LiCl) and polyacrylamide (PAM) was developed. The LiCl-PAM electrolyte film had an amorphous structure and an ionic conductivity > 10 mS cm^− 1. The addition of LiCl to the polyacrylamide did not alter the chemical bonding of PAM. Symmetric double layer capacitors (EDLC) were constructed using CNT-graphite electrodes. The solid EDLC retained approximately 85% of the capacitance achieved with a baseline cell in a LiCl aqueous solution. The solid EDLC devices demonstrated a wide voltage window (1.5 V), good cycle life (> 10,000 cycles), and excellent rate capability (up to 5 V s^− 1).     

Outstanding room-temperature capacitance of biomass-derived microporous carbons in ionic liquid electrolyte

A remarkable capacitance of 180 F·g^− 1 (at 5 mV·s^− 1) in solvent-free room-temperature ionic liquid electrolyte, 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, was achieved in symmetric supercapacitors using microporous carbons with a specific surface area of ca. 2000 m²·g^− 1 calculated from gas sorption by the 2D-NLDFT method. The efficient capacitive charge storage was ascribed to textural properties: unlike most activated carbons, high specific surface area was made accessible to the bulky ions of the ionic liquid electrolyte thanks to micropores (1–2 nm) enabled by fine-tuning chemical activation. From the industrial perspective, a high volumetric capacitance of ca. 80 F·cm^− 3 was reached in neat ionic liquid due to the absence of mesopores. The use of microporous carbons from biomass waste represents an important advantage for large-scale production of high energy density supercapacitors.     

Preparation and electrochemical characterization of the porous sulfur cathode using a gelatin binder

A novel porous sulfur cathode in which a gelatin was used as the binder was prepared by using a freeze–drying method at −58 °C. The porous structure provides channels for electrolyte infiltration and then facilitates ion diffusion. This porous sulfur cathode has a high initial capacity of 1235 mAh g⁻¹ and a high reversible capacity of 626 mAh g⁻¹ after 50 cycles, both of which are higher than that of the normal cathodes with compact structures.     

Li2SO4-polyacrylamide polymer electrolytes for 2.0 V solid symmetric supercapacitors

A neutral polymer electrolyte comprised of lithium sulfate (Li₂SO₄) and polyacrylamide (PAM) was developed. The Li₂SO₄-PAM electrolyte film shows an ionic conductivity up to 10 mS cm^− 1 in 45%RH conditions. Solid double layer capacitors were demonstrated using CNT-graphite electrodes and Li₂SO₄-PAM solid electrolytes. The voltage window of the solid cell was about 2.0 V, identical to that of a Li₂SO₄ liquid cell used as baseline. The demonstrated voltage window is significantly larger than that reported for proton- or hydroxyl-conducting electrolytes, suggesting that the Li₂SO₄-PAM electrolyte is a promising system for high energy density supercapacitors. The solid device also demonstrated excellent rate capability (up to 5 V s^− 1) and good cycle life (beyond 10,000 charge/discharge cycles).     

A new promising high temperature lithium battery solid electrolyte

Lithium lanthanoid silicates find importance as a solid electrolyte in high temperature lithium batteries in view of its high ionic conductivity at high temperatures. An first ever attempt is made to synthesis a new high temperature solid electrolyte viz., lithium samarium holmium silicate by sol–gel process and it has been characterized by thermal analysis (TGA–DTA), X-ray diffraction (XRD), infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). Lithium ion conductivity of 0.8087 × 10⁻⁷ Ω⁻¹ cm⁻¹ at 25 °C was obtained and it increases with increasing temperature. For the first time a highest conductivity of 0.1095 × 10⁻² Ω⁻¹ cm⁻¹ was obtained at 850 °C which is high compared to other high temperature lithium battery solid electrolytes.     

Proton-conducting solid oxide fuel cell (SOFC) with Y-doped BaZrO3 electrolyte

Y-doped BaZrO₃ (BZY) electrolyte films are successfully fabricated by utilizing the driving force from the anode substrate, aiming to circumvent the refractory nature of BZY materials. The BZY electrolyte film on the high shrinkage anode becomes dense after sintering even though no sintering aid is added, while the BZY electrolyte remains porous on the conventional anode substrate after the same treatment. The resulting BZY electrolyte shows a high conductivity of 4.5 × 10^− 3 S cm^− 1 at 600 °C, which is 2 to 20 times higher than that for most of BZY electrolyte films in previous reports. In addition, the fuel cell with this BZY electrolyte generates a high power output of 267 mW cm^− 2 at 600 °C. These results suggest the strategy presented in this study provides a promising way to prepare BZY electrolyte films for fuel cell applications.     

Strong anion receptor-assisted boron-based Mg electrolyte with wide electrochemical window and non-nucleophilic characteristic

Herein we present a strong anion receptor-assisted Mg-ion electrolyte, which is synthesized from tris(2H-hexafluoroisopropyl) borate (THFPB) and MgO in 1,2-dimethoxyethane (DME). The as-prepared borate magnesium oxide complex (BMOC) electrolyte delivers exceptional electrochemical performances, including extremely high anodic stability (up to 4.2 V vs. Mg), non-corrosivity to stainless steel and aluminium foils, and reasonable ionic conductivity of 1.74 × 10^− 4 S cm^− 1. In addition, by virtue of the non-nucleophilic characteristic of the BMOC electrolyte, S ||BMOC ||Mg cells have been assembled, which show a high stable discharge capacity of 1030 mAh g^− 1 for 15 cycles and one well-defined voltage plateau of ≈ 1.1 V vs. Mg, yielding a desirable energy density beyond 1100 Wh kg^− 1 based on the weight of sulfur in cathodes.     

A novel polymeric electrolyte based on a copolymer containing self-assembled stearylate moiety for lithium-ion batteries

A novel polymeric electrolyte based on a self-assembled copolymer moiety has been prepared by a simple method of photo-induced radical polymerization of a mixture consisting of stearylmethacrylate (SMA) and poly(ethylene glycol)-monomethacrylate (PEM) that dissolves LiBF₄ as the electrolytic salt. The SMA moiety work as mechanically stable backbone and the PEM unit dissolving the salts serves as ion-conducting path in the polymeric composite. Solid-state NMR measurements indicated that the resulting polymer composite consists of PEM-rich and SMA-rich phases, each of which exists within several nanometers apart. The ionic conductivity of the polymer electrolyte with the composition of PEM/SMA = 7/3 (by mass ratio) was 2.8 × 10^?5 S cm^?1 at 50 °C, which was significantly higher than that of the polymer electrolyte based on cross-linked PEM copolymer without SMA.     

Enhanced supercapacitive behaviors of birnessite

The birnessite type manganese dioxide electrode was prepared by the electrochemical stimulation as we recently described. It showed 190 F g⁻¹ in a Na₂SO₄ aqueous solution between −0.1 and 0.9 V versus Ag/AgCl at 1 A g⁻¹. The specific capacitance of birnessite was decreased by the manganese dissolution when the reduction and oxidation were repeated. By adding small amounts of Na₂HPO₄ or NaHCO₃ into the electrolyte, the capacitance increased to 200–230 F g⁻¹ and the manganese dissolution was successfully suppressed. Thanks to the additives, the birnessite demonstrated the much improved cycleability over >1800 cycles.     

Noncovalently functionalized water-soluble multiwall-nanotubes through azocarmine B and their application in nitric oxide sensor

A new noncovalent approach for the dissolution of MWNTs in water by azocarmine B (ACB) is reported. Through a simple electro-polymerization procedure, a novel electrochemical NO sensor based on water-soluble MWNTs and polyazocarmine B (PACB) nanofilm electrode was prepared, which showed excellent electrocatalytic activity towards the oxidation of nitric oxide (NO). The oxidation current linearly increased with the nitric oxide concentration in the range of 2.2 × 10⁻⁷–1.2 × 10⁻⁴ mol L⁻¹ with a low detection limit of 2.8 × 10⁻⁸ mol L⁻¹. The sensor has the merit of good stability, reproducibility, high sensitivity and selectivity, and it can be used to monitor NO released from rat liver cells effectively.     

Carboxylic and sulfonic N-substituted naphthalene diimide salts as highly stable non-polymeric organic electrodes for lithium batteries

Two N-substituted naphthalene tetracarboxylic diimide (NTCDI) ionic compounds, carboxylic and sulfonic sodium salts, were prepared and used as positive electrode active materials in lithium-half cells. The aim of this investigation was to assess the solubility-suppressing effect of two different negatively charged substituent groups on a redox-active organic backbone using a carbonate-based liquid electrolyte. NTCDI derivatives were obtained in high yields from reaction of naphthalene tetracarboxylic dianhydride with neutralized glycine or with neutralized taurine. They were mixed with carbon black and cycled in galvanostatic mode against lithium metal using 1 M LiPF₆ EC/DMC liquid electrolyte. These two NTCDI derivatives exhibit a quite stable electrochemical activity upon cycling at an average potential of 2.3 V vs. Li⁺/Li⁰ giving rise to specific capacity values of 147 mAh·g^− 1 and 113 mAh·g^− 1 for the dicarboxylate and the disulfonate derivative, respectively. This study clearly supports the useful effect of such grafted permanent charges as a general rule on the electrochemical stability of crystallized organic materials based on the assembly of small redox-active units.     

Suppression of dendritic lithium formation by using concentrated electrolyte solutions

This study examined the electrochemical deposition and dissolution of lithium on nickel electrodes in a propylene carbonate (PC) electrolyte containing different LiN(SO₂C₂F₅)₂ concentrations. The electrolyte concentration was found to have a significant effect on the reactions occurring at the electrode. The poor cycleability of the electrodes in the low-concentration solutions was improved considerably by increasing the electrolyte concentration. Transmission electron microscopy (TEM) revealed that a high-concentration solution produces a thinner solid electrolyte interphase (SEI) on the electrodeposited lithium than a low-concentration solution, e.g., ∼35 nm in 1.28 mol kg⁻¹ vs. ∼20 nm in 3.27 mol kg⁻¹ solutions. Raman spectroscopy showed that the solvation number of lithium ions differed according to the electrolyte concentration. This suggests that the structure of solvated lithium ions is an important factor in suppressing dendritic lithium formation.     

A dual–ion battery using diamino–rubicene as anion–inserting positive electrode material

A novel and non-polymeric anion-inserting electrode material has been designed and prepared for promoting research on molecular ion rechargeable batteries: 5,12-diaminorubicene (DARb). The apolar core structure of a rubicene molecule has been coupled to two amino-groups for producing an original conjugated primary diamine exhibiting low affinity for polar solvents such as common carbonate-based battery electrolytes. The electrochemical reactivity of this organic molecule has been probed in a dual-ion cell configuration (vs. Li) using six different electrolyte formulations in terms of solvent (PC, EC-DMC) and lithium salt (LiPF₆, LiClO₄, LiTFSI). This diamino-rubicene material systematically showed a reversible electroactivity and promising performances when using 1 M LiPF₆ in EC:DMC (1:1 vol.%) as the electrolyte, such as an average potential of ~ 3.4 V vs. Li⁺/Li⁰, an initial capacity of 115 mAh·g^− 1 and a good capacity retention over 60 cycles without any optimization.     

Life test of DMFC using poly(ethylene glycol)bis(carboxymethyl)ether plasticized PVA/PAMPS proton-conducting semi-IPNs

A novel, low-cost proton-conducting semi-IPN has been successfully prepared from PVA/PAMPS blends by incorporating poly(ethylene glycol)bis(carboxymethyl)ether (PEGBCME) as a novel plasticizer. Although, the polymer is based on a relatively low content of PAMPS as a component of ion conducting sites, the resulting semi-IPN exhibited high proton conductivity (0.1 S cm⁻¹) at 25 °C, which afforded a higher power density of 51 mW cm⁻² at 80 °C. A striking feature is that a long-term initial performance is achieved with a 130 h of stable fuel cell operation in DMFC mode due to effectively suppressed methanol crossover. This is a new record for a fully hydrocarbon membrane in DMFC, seeing that the PVA–PAMPS proton-conducting semi-IPNs are made simply of aliphatic skeletons.