Lithium storage in perovskite lithium lanthanum titanate

Perovskite lithium lanthanum titanate (LLTO) was synthesized using sol–gel method. It shows a reversible capacity of 145 mA h g^− 1 and moderate cycling performance between 0.01 and 2.00 V. Cyclic voltammetry and X-ray diffraction results demonstrate a two-step solid–solution reaction behavior in the voltage range of 0.00–3.00 V upon lithium insertion/extraction. A stable solid electrolyte interphase (SEI) layer is formed on the surface of LLTO after the initial discharge. Carbon coating by chemical vapor deposition improves its cycling performance significantly.     

Electrodeposition of gold nanoparticles at a solid|ionic liquid|aqueous electrolyte three-phase junction

Gold nanoparticles have been electrodeposited on an electrode through electrogeneration at an ITO|AuCl₄^? solution in an ionic liquid|aqueous electrolyte three-phase junction. The electrodeposition was carried out by inverted double-pulse potential chronoamperometry. The direct reduction of AuCl₄^? ions at the electrode is followed by a counterion transfer through the liquid|liquid interface. Contrary to the electrodeposition from a single ionic liquid phase, scanning electron microscopy reveals that the shape of the resulting nanoparticles is highly angular and well-developed with a diameter of 110 ± 30 nm. Catalytic oxidation of glucose on the modified electrode is demonstrated.     

Controllable growth of gold nanowires and nanoactuators via high-frequency AC electrodeposition

An electrochemical deposition method using high-frequency alternating current (AC) signal is reported here for the in situ synthesis and assembly of Au nanowires and nanoactuators on microelectrodes without using any masks or templates. High conductivity of 3.79 ± 0.14 × 10⁷ Ω^− 1 m^− 1 is achieved on the Au nanowires assembled between electrodes. Au nanoactuators with expansion ratio of more than 500% can be fabricated at higher frequency. The actuators can act as claws to grab SiO₂ nanoparticles in a water solution when driven by an alternating electric field. Disconnected nanowires and nanoparticles which self-aligned around the electrodes were also obtained at lower gold ion concentration, indicating a different current transfer mode in AC electrodeposition.     

Electrodeposition of CuInSe2 films by an alternating double-potentiostatic method using nearly neutral electrolytes

One step electrodeposition with an alternating double-potentiostatic(DPSED) program was used to prepare CuInSe₂ thin films in nearly neutral aqueous electrolytes with sodium citrate complex. Linear sweep voltammetry(LSV) was measured to probe voltammetric properties of electrolytes with respect to Cu, In and Se individual precursor and their mixed solutions. Compositional and structural characteristics of the as-deposited and annealed films at 400 °C in Ar atmosphere for 0.5 h were analyzed by XRD and XPS. The results showed that reduction of Cu²⁺ to Cu⁺ at one potential point of ?800 mV and subsequently formation of CuIn alloy as well as metal In and amorphous Se at the other potential point of ?1400 mV were responsible for synthesis of CISe chalcopyrite. Composition self-regulation made DPSED films have three elements co-deposition and more uniform element distribution, which promoted chalcopyrite CISe formation.     

Design of a bioelectrocatalytic electrode interface for oxygen reduction in biofuel cells based on a specifically adapted Os-complex containing redox polymer with entrapped Trametes hirsuta laccase

The design of the coordination shell of an Os-complex and its integration within an electrodeposition polymer enables fast electron transfer between an electrode and a polymer entrapped high-potential laccase from the basidiomycete Trametes hirsuta. The redox potential of the Os^3+/2+-centre tethered to the polymer backbone (+ 720 mV vs. NHE) is perfectly matching the potential of the enzyme (+ 780 mV vs. NHE at pH 6.5). The laccase and the Os-complex modified anodic electrodeposition polymer were simultaneously precipitated on the surface of a glassy carbon electrode by means of a pH-shift to 2.5. The modified electrode was investigated with respect to biocatalytic O₂ reduction to H₂O. The proposed modified electrode has potential applications as biofuel cell cathode.     

Preparation and electrocatalytic activity of Rh adlayers on Pt(1 0 0) electrodes: reduction of nitrous oxide

Rhodium adlayers (submonolayer range) have been prepared on Pt(1 0 0) electrodes by electrodeposition from acidic solutions containing an excess of chloride. These Rh/Pt(1 0 0) electrodes give a well-defined voltammetric signal in the hydrogen adsorption region, which gives evidence of a high level of order in the Rh adlayer and allow a reliable estimation of the coverage. The voltammetric behavior of the Rh/Pt(1 0 0) electrodes points to an epitaxial growth with formation of rhodium islands. The well-ordered bimetallic surfaces freshly prepared were tested as electrocatalysts for nitrous oxide reduction and the responses were compared with those of the bulk Pt(1 0 0) and Rh(1 0 0) electrodes. The voltammogram for the bimetallic surface showed well separated N₂O reduction signals for Rh and Pt surface zones. An exceptionally high electrocatalytic activity for the Rh adlayer was found for low coverages. This behavior is explained on the basis of a high activity of the rhodium adatoms in the periphery of the islands.     

Tube-covering-tube nanostructured polyaniline/carbon nanotube array composite electrode with high capacitance and superior rate performance as well as good cycling stability

The combination of a vertically aligned carbon nanotube array (CNTA) framework and electrodeposition technique leads to a tube-covering-tube nanostructured polyaniline (PANI)/CNTA composite electrode with hierarchical porous structure, large surface area, and superior conductivity. PANI/CNTA composite electrode has high specific capacitance (1030 F g⁻¹), superior rate capability (95% capacity retention at 118 A g⁻¹), and high stability (5.5% capacity loss after 5000 cycles). Energy storage characteristics of the PANI/CNTA composite are presented in this paper.     

Hierarchically ordered porous nickel oxide array film with enhanced electrochemical properties for lithium ion batteries

Hierarchically ordered porous nickel oxide array film was prepared by electrodeposition through monolayer polystyrene spheres template. The as-prepared film had a highly porous structure of interconnected macrobowls array possessing nanopores. As anode material for lithium ion batteries, the porous array NiO film exhibited weaker polarization, higher coulombic efficiency and better cycling performance in comparison with the dense NiO film. After 50 cycles, the discharge capacity of porous array NiO film was 518 mAh g^? 1 at 1 C rate, higher than that of the dense NiO film (287 mAh g^? 1). The enhancement of the electrochemical properties was due to the unique hierarchical porous architecture, which provided fast ion/electron transfer and alleviated the structure degradation during the cycling process.     

Raman spectroscopy investigation on (Pb1−xLax)(Zr0.90Ti0.10)1−x/4O3 ceramic system

A Raman spectroscopy study at room temperature was carried out on (Pb_1−xLa_x)(Zr_0.90Ti_0.10)_1−x/4O₃ ceramics (x = 2, 3, 4 at%). The results were analyzed considering the x-ray patterns at room temperature showing a mixture of two phases: a rombohedral-ferroelectric phase and an orthorhombic-antiferroelectric, increasing the% of the second one with the lanthanum concentration. For x = 3 at%, the analysis was also carried out in a wide temperature range. Two anomalies were evaluated, one around 363 K, which has been associated to a ferroelectric-antiferroelectric phase transition; the second one around 430 K, which has been associated to a transition from an incommensurable state to a ferroelectric phase.     

Direct electrodeposition of PbTe thin films on n-type silicon

High quality lead telluride thin films were directly deposited onto n-type silicon (1 0 0) substrates by electrodeposition at room temperature. The deposition mechanism was studied using cyclic voltammetry. The films were characterized by scanning electron microscopy, energy dispersive X-ray, X-ray diffraction, and Fourier transform infrared spectroscopy. The results indicated that the deposited PbTe films exhibited a polycrystalline rock salt structure and good optical properties with a direct band gap of 0.31 eV.     

Photoluminescence of La/Ti mixed oxides prepared using sol–gel process and their pCBA photodecomposition

La/Ti mixed oxides with weight ratios of 1:9, 2:8, 3:7, and 4:6 were prepared by sol–gel method. The photocatalytic activity of La/Ti oxides was evaluated based on the pCBA photodecomposition. The catalyst samples were characterized by XRD, TEM, DRS, BET, and photoluminescence (PL) spectra. Particles of the La/Ti-mixed oxides showed the diameter of about 7 nm. We found that 30% doping of lanthanum ions on the TiO₂ powders induced the highest pCBA (4-chlorobenzonic acid) photodecomposition in these experimental conditions. The order of its photoactivity was as following: 30 > 20 > 0 > 10 > 40 wt%, which was the same for PL tendency. Also, PL spectra intensity increased with calcination temperature from 500 to 600 °C, then decreased at 700 °C. Phtotcatalytic activity followed the trend of the PL spectra intensity. The modification of TiO₂ surface by lanthanum ion made it possible to enhance the photoactivity by retarding the recombination of photoexcited electron/hole pairs, in the result of the higher photoactivity in the stronger PL intensity.     

Determination of hydrogen sulfide in gasoline by Au nanoclusters modified glassy carbon electrode

A promising hydrogen sulfide (H₂S) sensor was prepared by electrodeposition of Au nanoclusters on glassy carbon electrode (GCE) and the surface structure was characterized by SEM and EDAX. These flower-like form Au nanoclusters, which were made up of highly dense clustering Au nanorods with an average diameter of 20 nm and length up to 80 nm, had an average size about 600 nm and uniformly distributed on the GCE surface. The electrocatalytic oxidation of H₂S in gasoline was performed on this modified electrode, which had a satisfactory liner response to H₂S in the range of 1–80 ppm and a detection limit of 0.45 ppm (s/n = 3). This sensor was sensitive, selective and stable.     

Micro-electrodeposition in the presence of ionic liquid for the preconcentration of trace amounts of Fe,Co, Ni and Zn from aqueous samples

The paper presents the preconcentration of trace elements via electrodeposition onto a (micro)aluminum cathode in the presence of ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate [BMIM][PF₆] as a supporting electrolyte. The advantages of the proposed method include very simple instrumentation for the preconcentration of trace elements and low-cost reagents. The experiment showed that the use of ionic liquid in the electrodeposition process significantly improves sensitivity, recovery and detection limits for the determination of trace amounts of iron, cobalt, nickel and zinc. The preconcentrated metals were determined using X-ray fluorescence spectrometry. The optimum parameters for electrodeposition such as pH, the volume of the analyzed solution, the voltage and the deposition time were studied. Under the optimized conditions, the detection limits were 5, 2, 3 and 6 μg L^− 1 for iron, cobalt, nickel and zinc, respectively. The precision and recovery of the method were in the range of 3–5.5%, and 92–103%, respectively. The calibration was performed using aqueous standards of Fe(III), Co(II), Ni(II) and Zn(II) in the range 0.01–0.25 mg L^− 1. The method was applied successfully in water analysis.     

One-step fabrication of chitosan–hematite nanotubes composite film and its biosensing for hydrogen peroxide

This work reports on a novel chitosan–hematite nanotubes composite film on a gold foil by a simple one-step electrodeposition method. The hybrid chitosan–hematite nanotubes (Chi–HeNTs) film exhibits strong electrocatalytic reduction activity for H₂O₂. Interestingly, two electrocatalytic reduction peaks are observed at −0.24 and −0.56 V (vs SCE), respectively, one controlled by surface wave and the other controlled by diffusion process. The Chi–HeNTs/Au electrode shows a linear response to H₂O₂ concentration ranging from 1 × 10⁻⁶ to 1.6 × 10⁻⁵ mol L⁻¹ with a detection limit of 5 × 10⁻⁸ mol L⁻¹ and a sensitivity as high as 1859 μA μM⁻¹ cm⁻².     

Electrodeposition of hyaluronic acid and hyaluronic acid–bovine serum albumin films from aqueous solutions

Hyaluronic acid (HYH) films were prepared from aqueous sodium hyaluronate (HYNa) solutions by anodic electrodeposition. The film thickness was varied in the range of 0–20 μm by the variation of the deposition time and HYNa concentration. The deposition rate was low at HYNa concentration below 1 g L⁻¹ and increased significantly in the range of 3–5 g L⁻¹. The addition of bovine serum albumin (BSA) to the HYNa solutions resulted in increased deposition yield, which was attributed to the formation of composite HYH–BSA films. The thickness of the HYH–BSA films deposited by anodic electrodeposition was varied in the range of 0–80 μm. The HYH and composite HYH–BSA films were studied by scanning electron microscopy, thermogravimetric analysis, differential thermal analysis, Fourier transform infrared spectroscopy and circular dichroism spectroscopy. The deposition mechanism and kinetics of deposition are discussed.     

Impedance measurements of nanoporosity in electrodeposited ZnO films for DSSC

Porous ZnO/dye hybrid films have been deposited by cathodic electrodeposition, and their active surface area after dye desorption was evaluated by impedance measurements with the semiconducting electrode polarized in accumulation. Surface area ratios have been deduced for a large number of films from imaginary part Z″ vs. frequency measurements, having a constant rate over the frequency range from 0.5 Hz to > 50 Hz. The active surface increased by a factor of roughly 150 per every micron of film with respect to the area of a flat ZnO electrode: this linear relationship held from less than 1 µm up to 9 µm thick films.     

Enhanced magnetism in electrodeposited-based CoNi composites containing high percentage of micron hard-magnetic particles

CoNi–barium ferrite magnetic composites with a high percentage of micrometric particles have been prepared by electrodeposition over silicon-based substrates. A cationic surfactant synthesized in our laboratory (4-ethylazobenzene-4′-(oxyethyl)trimethylammonium iodide-AZTMAI) has been used in order to favour the inclusion of magnetic particles into the alloy deposit. This surfactant reduces during cobalt–nickel electrodeposition and it is not embedded into the deposit. Moderate surfactant concentrations (1–5 g l⁻¹), room temperature, the application of a magnetic field during the electrodeposition and a double-pulse technique favour the maximum incorporation of barium ferrite up to around 30–35 wt%. Magnetic properties of composites prepared tend to hard-magnetic ones, with different magnetization curves when silicon/seed-layer/composite samples are oriented parallel or perpendicularly to the applied magnetic field. Constricted-type magnetization curves were obtained.     

In situ study of nitrobenzene grafting on Si(1 1 1)-H surfaces by infrared spectroscopic ellipsometry

The binding of nitrobenzene (NB) molecules from a solution of 4-nitrobenzene-diazonium-tetrafluoroborate on a Si(1 1 1)-H surface was investigated during the electrochemical processing in diluted sulphuric acid by means of infrared spectroscopic ellipsometry (IR-SE). The grafting was monitored by an increase in specific IR absorption bands due to symmetric and anti-symmetric NO₂ stretching vibrations in the 1400–1700 cm^?1 regime. The p- and s-polarized reflectances were recorded within 20 s for each spectrum only. NB molecules were detected when bonded to the Si(1 1 1) surface but not in the 2 mM solution itself. Oxide formation on the NB grafted Si surface was observed after drying in inert atmosphere and not during the grafting process in the aqueous solution.     

Stability of underpotentially deposited Ag layers on a Au(1 1 1) surface studied by surface X-ray scattering

Stability of underpotentially deposited (upd) Ag layers on Au(1 1 1) surface was investigated by surface X-ray scattering (SXS). While the complete pseudomorphic Ag bilayer on Au(1 1 1) surface obtained by upd at 10 mV (vs. Ag/Ag⁺) was maintained its structure even after the circuit was disconnected and the surface was exposed to ambient atmosphere, the pseudomorphic Ag monolayer obtained by upd at 50 mV was converted to a partial bilayer with the coverage of 0.66 and 0.46 ML for the 1st and 2nd layer, respectively. These results show that Ag bilayer is structurally more stable than Ag monolayer on Au(1 1 1) and Ag atoms of the upd monolayer move around on the Au(1 1 1) surface without potential control.     

Electrodeposition of Ag nanoparticles onto carbon coated TEM grids: A direct approach to study early stages of nucleation

An innovative experimental approach to study the electrodeposition of small nanoparticles and the early stages of electrochemical nucleation and growth is presented. Carbon coated gold TEM grids are used as substrates for the electrodeposition of silver nanoparticles so that electrochemical data, FESEM, HAADF–STEM and HRTEM data can be acquired from the same sample without the need to remove the particles from the substrate. It is shown that the real distribution of nanoparticles cannot be resolved by FESEM whereas HAADF–STEM analysis confirms that a distribution of ‘small’ nanoparticles (d ≈ 1–2 nm) coexist with ‘large’ nanoparticles corresponding to a bimodal size distribution. Besides, particles grown under the same conditions have been found to present different structures such as monocrystals, polycrystals or aggregates of smaller particles.