Electrochemical performance of a novel CoTETA/C catalyst for the oxygen reduction reaction

In this communication, we report a novel CoTETA/C catalyst for the oxygen reduction reaction (ORR) which was prepared from a carbon-supported cobalt triethylenetetramine chelate, followed by heat treatment in an inert atmosphere. Electrochemical performances were measured using rotating disk electrode (RDE) technique and a PEM fuel cell test station. For a H₂–O₂ fuel cell system, the maximum output power density reached 162 mW cm^?2 at 25 °C with non-humidified reaction gases. We found a nanometallic face-centered cubic (fcc) α-Co phase embedded in the graphitic carbon after pyrolysis, based on X-ray absorption spectroscopy (XAS) and X-ray diffraction (XRD) measurements. These results indicated that CoTETA/C is a promising catalyst for the ORR.     

O2 surface concentration change and its implication on oxygen reduction mechanism and kinetics at platinum in acidic media

O₂ concentration near Pt surface during oxygen reduction reaction (ORR) in 0.1 M HClO₄ has been monitored by rotating ring-disk electrodes system. At 0.8 V < E < 1.0 V (vs. RHE), O₂ concentration near Pt surface increases with potential accompanying with the decrease of ORR current at the disk electrode; O₂ concentration in the negative-going scan is larger than that at the same potential in the positive-going scan, while ORR current shows the opposite trend at ω > 400 rpm. At E > 0.8 V accumulation of O_ad|OH_ad at Pt disk electrode with ORR time is evident, revealing that O_ad|OH_ad formation rate is faster than that for the removal of OH_ad to H₂O under such conditions. At relatively lower rotation speed and faster scan rate, the cathodic current during ORR in the negative-going scan can be larger than that in the positive-going scan with a current peak at ca. 0.8 V, which is attributed to the superimposition of ORR current increase due to change of O₂ concentration near the surface and the additional reduction of O_ad|OH_ad formed from decomposed O₂ at higher potentials.     

Novel synthesis of a highly active carbon-supported Ru85Se15 chalcogenide catalyst for the oxygen reduction reaction

A carbon-supported Ru₈₅Se₁₅ chalcogenide catalyst was synthesized via a microwave-assisted polyol process using RuCl₃ and Na₂SeO₃ as the Ru and Se precursors. The Ru₈₅Se₁₅ chalcogenide catalyst was characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM) and inductively-coupled plasma-atomic emission spectroscopy (ICP-AES). The XRD pattern for Ru₈₅Se₁₅/C clearly exhibited the characteristic reflections of metallic ruthenium. The TEM image indicated that the Ru₈₅Se₁₅ chalcogenide catalyst was well dispersed on the surface of the carbon support with a narrow particle size distribution. Rotating disk electrode (RDE) and single-cell measurements were carried out to evaluate the electrocatalytic activity of the Ru₈₅Se₁₅ chalcogenide catalyst. The oxygen reduction reaction (ORR) activity of the Ru₈₅Se₁₅/C catalyst was compared with the commercial Pt/C catalyst with the absence/presence of methanol. In the absence of methanol, the Ru₈₅Se₁₅/C catalyst showed a comparable ORR activity with the Pt/C catalyst. However, in the presence of methanol, the Ru₈₅Se₁₅/C catalyst showed a better ORR activity than the Pt/C catalyst. The performance of the membrane electrode assembly (MEA) prepared with Ru₈₅Se₁₅/C as the cathode catalyst in a single proton exchange membrane fuel cell (PEMFC) showed the maximum power density of 400 mW cm⁻² at the current density of 1300 mA cm⁻².     

Oxygen reduction reaction on the low index planes of palladium electrodes modified with a monolayer of platinum film

Oxygen reduction reaction (ORR) has been studied on the low index planes of Pd modified with a monolayer of Pt (Pt/Pd(hkl)) in 0.1 M HClO₄ with the use of hanging meniscus rotating disk electrode. The activity for ORR on bare Pd(hkl) electrode depends on the surface structure strongly, however, voltammograms of ORR on Pt/Pd(hkl) electrodes do not depend on the crystal orientation. The specific activities of Pt/Pd(hkl) electrodes at 0.90 V (RHE) are higher than that on Pt(1 1 0) which has the highest activity for ORR in the low index planes of Pt. The mass activity on Pt/Pd(hkl) electrode is 7 times as high as a commercial Pt/C catalyst.     

Oxygen reduction behavior of RuO2/Ti,IrO2/Ti and IrM (M: Ru,Mo, W,V) Ox/Ti binary oxide electrodes in a sulfuric acid solution

Some oxide catalysts, such as RuO₂/Ti, IrO₂/Ti and IrM(M: Ru, Mo, W, V)O_x/Ti binary oxide electrodes, were prepared by using a dip-coating method on a Ti substrate. Their catalytic behavior for the oxygen reduction reaction (ORR) was evaluated by cyclic voltammetry in 0.5 M H₂SO₄ at 60 °C. These catalysts were found to exhibit considerably high activity, and the most active one among them was Ir_0.6V_0.4O₂/Ti prepared at 450 °C, showing onset potential for the ORR at about 0.86 V–0.90 (vs RHE).     

Influence of the proton transport on the ORR kinetics and on the H2O2 escape in three-dimensionally ordered electrodes

In this study, we use rotating ring disc electrode measurements to investigate the influence of the proton transport on the kinetics of the oxygen reduction reaction (ORR) in a 3D nanostructured catalytic layer based on Pt nanoparticles supported on vertically aligned carbon nanofibers. The results confirm that protons are involved in the rate determining step of the ORR in acidic media. For pH ≥ 3, the ORR occurs in two successive reduction waves. The first current plateau is limited by the proton diffusion and is followed by the second reduction wave attributed to the mechanism involving water dissociation. The shape of the H₂O₂ escape current curve is strongly affected by the pH of the solution and shows a pronounced maximum when the pH value is increased. These experimental features are discussed with the help of a kinetic model.     

Oxygen reduction reaction on carbon-supported palladium nanocubes in alkaline media

Carbon-supported Pd nanocubes with the size of 30, 10 and 7 nm were prepared and their electrocatalytic activity towards the oxygen reduction reaction (ORR) in alkaline solution was studied. For comparison carbon-supported spherical Pd nanoparticles and commercial Pd/C catalyst were used. The catalysts were characterised by transmission electron microscopy, electro-oxidation of carbon monoxide and cyclic voltammetry and the ORR activity was evaluated using the rotating disk electrode method. The ORR on all studied Pd/C catalysts proceeded via four-electron pathway where the rate-limiting step was the transfer of the first electron to O₂ molecule. The specific activity of Pd nanocubes was more than two times higher than that of spherical Pd nanoparticles and increased with increasing the particle size.     

Ternary non-noble metal chalcogenide (W–Co–Se) as electrocatalyst for oxygen reduction reaction

In this study, a catalyst based on a novel ternary non-noble metal chalcogenide, W–Co–Se, was synthesized for the oxygen reduction reaction (ORR) in acidic medium. The non-noble metal chalcogenide catalyst was electrochemically stable in the potential range of 0.05–0.8 V versus NHE in 0.5 M H₂SO₄ aqueous solution. This catalyst demonstrated significant catalytic activity towards the ORR, showing the ORR onset potential at 0.755 V versus NHE in 0.5 M H₂SO₄ at 25 °C. Such high activity might be attributed to the electronic structure of non-noble metals modified by chalcogen.     

The kinetics of the oxidation and reduction of H2O2 at a Pt electrode: A differential electrochemical mass spectrometric study

The kinetics of the oxidation and reduction of hydrogen peroxide (HPOOR, HPORR) at a Pt electrode in 0.1 M HClO₄ + 2 mM H₂O₂ are investigated by Differential Electrochemical Mass Spectrometry (DEMS) in a flow cell. The O₂ mass signal was recorded during cyclic voltammetry, and its potential dependence follows the shape of the cyclic voltammogram. Partial currents for HPOOR and HPORR are estimated based on the O₂ mass signal and the total Faradaic current. The onset overpotential for HPORR at the Pt electrode is above 0.6 V. It is limited by the thermodynamics of OH_ad desorption, as is also the case with ORR. The onset overpotential for HPOOR is below 0.1 V, due to the faster consumption of H₂O₂ through HPORR at these potentials and the small bulk H₂O₂ concentration used.     

Pt4ZrO2/C cathode catalyst for improved durability in high temperature PEMFC based on H3PO4 doped PBI

In this paper, Pt₄ZrO₂/C was prepared and compared with commercial Pt/C (46.6 wt.% TKK) in terms of the durability as cathode catalyst in a high temperature proton exchange membrane fuel cell (PEMFC) based on H₃PO₄ doped polybenzimidazole (PBI) by a potential sweep test. The catalysts before and after the potential sweep test were characterized by rotating disk electrode (RDE), X-ray diffraction (XRD), transmission electron microscopy (TEM) and inductively coupled plasma-atomic emission spectroscopy (ICP-AES). After 3000 cycles potential sweep test, the overall performance loss of the Pt₄ZrO₂/C membrane electrode assembly (MEA) was less than that of the Pt/C MEA. The RDE results demonstrated that the oxygen reduction reaction (ORR) activity of the as-prepared Pt₄ZrO₂/C is nearly the same as TKK-Pt/C. The XRD and TEM results showed that Pt₄ZrO₂/C catalyst presented higher sintering resistance than commercial Pt/C catalyst during the potential sweep test. This may be attributed to the addition of ZrO₂, which acts an anchor to inhibit the adjacent platinum particles to agglomerate. The ICP-AES results of Pt₄ZrO₂/C cathode catalyst before and after the potential sweep test showed that the composition of Pt and Zr were very near the nominal atomic ratio of Pt:Zr, which reflected that Pt₄ZrO₂/C catalyst had a good stability during the potential sweep test. In brief, the preliminary results indicate that Pt₄ZrO₂/C catalyst is a good candidate of Pt/C catalyst in high temperature PEMFC based on H₃PO₄ doped PBI for achieving longer cell life-time and higher cell performance.     

Transition metal-nitrogen-carbon catalysts for oxygen reduction reaction in neutral electrolyte

Platinum group metal-free (PGM-free) catalysts based on M-N-C types of materials with M as Mn, Fe, Co and Ni and aminoantipyrine (AAPyr) as N-C precursors were synthesized using sacrificial support method. Catalysts kinetics of oxygen reduction reaction (ORR) was studied using rotating ring disk electrode (RRDE) in neutral pH. Results showed that performances were distributed among the catalysts as: Fe-AAPyr > Co-AAPyr > Mn-AAPyr > Ni-AAPyr. Fe-AAPyr had the highest onset potential and half-wave potential. All the materials showed similar limiting current. Fe-AAPyr had an electron transfer involving 4e⁻ with peroxide formed lower than 5%. Considering H₂O₂ produced, it seems that Co-AAPyr, Mn-AAPyr and Ni-AAPyr follow a 2 × 2e⁻ mechanism with peroxide formed during the intermediate step. Durability test was done on Fe-AAPyr for 10,000 cycles. Decrease of activity was observed only after 10,000 cycles.     

Performance enhancement of phosphoric acid-based proton exchange membrane fuel cells by using ammonium trifluoromethanesulfonate

In a fuel cell system where concentrated phosphoric acid (PA) is used as a proton conducting medium, the use of PA causes some undesirable effects on oxygen reduction reaction (ORR) at Pt catalyst. Ammonium trifluoromethanesulfonate (ATFMS) is introduced as a cathode additive to increase the local oxygen concentration near the Pt catalyst. A cathode with the optimum composition of ATFMS shows a higher single cell performance than that without the additive when a single cell based on a PA-doped polymer membrane is operated at 150 °C. The enhanced ORR activity and oxygen solubility with the incorporation of ATFMS are proved with rotating disk electrode (RDE) and Pt microelectrode experiments. Single cell performance for longer than 600 h without decay in operating voltage could support the stability of the additive.     

Methane-fueled SOFC with traditional nickel-based anode by applying Ni/Al2O3 as a dual-functional layer

Novel γ-Al₂O₃ supported nickel (Ni/Al₂O₃) catalyst was developed as a functional layer for Ni–ScSZ cermet anode operating on methane fuel. Catalytic tests demonstrated Ni/Al₂O₃ had high and comparable activity to Ru–CeO₂ and much higher activity than the Ni–ScSZ cermet anode for partial oxidation, steam and CO₂ reforming of methane to syngas between 750 and 850 °C. By adopting Ni/Al₂O₃ as a catalyst layer, the fuel cell demonstrated a peak power density of 382 mW cm^?2 at 850 °C, more than two times that without the catalyst layer. The Ni/Al₂O₃ also functioned as a diffusion barrier layer to reduce the methane concentration within the anode; consequently, the operation stability was also greatly improved without coke deposition.     

Cyanamide-derived non-precious metal catalyst for oxygen reduction

Cyanamide was used in the preparation series of metal–nitrogen–carbon (M–N–C) oxygen reduction catalysts. The best catalyst, treated at 1050 °C, shows good performance versus previously reported non-precious metal catalysts with an OCV ~ 1.0 V and a current density of 105 mA/cm² (iR-corrected) at 0.80 V in H₂/O₂ fuel cell testing (catalyst loading: 4 mg cm^? 2). Although nitrogen content has been previously correlated positively with ORR activity, no such trend is observed here for any nitrogen type. The combined effects of nitrogen and sulfur incorporation into the carbon may account for the high activity of the 1050 °C catalyst.     

Platinum nanoparticles supported on nitrobenzene-functionalised graphene nanosheets as electrocatalysts for oxygen reduction reaction in alkaline media

A systematic study on the electrocatalytic properties of Pt nanoparticles supported on nitrobenzene-modified graphene (Pt-NB/G) as catalyst for oxygen reduction reaction (ORR) in alkaline solution was performed. Graphene nanosheets were spontaneously grafted with nitrophenyl groups using 4-nitrobenzenediazonium salt. The electrocatalytic activity towards the ORR and stability of the prepared catalysts in 0.1 M KOH solution have been studied and compared with that of the commercial Pt/C catalyst. The results obtained show that the NB-modified graphene nanosheets can be good Pt catalyst support with high stability and excellent electrocatalytic properties. The specific activity of Pt-NB/G for O₂ reduction was 0.184 mA cm⁻², which is very close to that obtained for commercial 20 wt% Pt/C catalyst (0.214 mA cm⁻²) at 0.9 V vs. RHE. The Pt-NB/G hybrid material promotes a four-electron reduction of oxygen and can be used as a promising cathode catalyst in alkaline fuel cells.     

Investigation of the oxygen evolution reaction on Ti/IrO2 electrodes using isotope labelling and on-line mass spectrometry

Oxygen evolution on Ti/IrO₂ anodes has been studied in 1M HClO₄ electrolyte using ¹⁸O labelling together with differential electrochemical mass spectrometry (DEMS) measurements.It has been shown that during successive cyclic voltammetric measurements in H₂ ¹⁸O containing electrolyte the amount of ¹⁶O₂ (m/z = 32) decreases, with a concomitant increase of ¹⁸O¹⁶O (m/z = 34) after each cycle before reaching a steady state after four cycles. The obtained higher ¹⁶O₂ concentration in the evolved oxygen during the first scans is because ¹⁶O from the IrO₂ film contribute in the oxygen evolution reaction.Analysis of the experimental data has shown that the amount of lattice oxygen, which is involved in the oxygen exchange reaction, is in the order of 1% of the total IrO₂ loading. This is an indication that only the outer surface of the oxide electrode participates in the oxygen evolution reaction.In a second series of experiments it has been demonstrated that oxygen evolution on Ir¹⁶O₂ in H₂¹⁸O containing electrolyte result in the formation of Ir¹⁸O₂.Consequently, we can conclude that the IrO₂ layers participate in the oxygen evolution reaction in acid media at least to a several monolayer extend.     

Pt and Pt–Ru nanoparticles decorated polypyrrole/multiwalled carbon nanotubes and their catalytic activity towards methanol oxidation

Conducting polymer composite films comprised of polypyrrole (PPy) and multiwalled carbon nanotubes (MWCNTs) [PPy–CNT] were synthesized by in situ polymerization of pyrrole on carbon nanotubes in 0.1 M HCl containing (NH₄)S₂O₈ as oxidizing agent over a temperature range of 0–5 °C. Pt nanoparticles are deposited on PPy–CNT composite films by chemical reduction of H₂PtCl₆ using HCHO as reducing agent at pH = 11 [Pt/PPy–CNT]. The presence of MWCNTs leads to higher activity, which might be due to the increase of electrochemically accessible surface areas, electronic conductivity and easier charge-transfer at polymer/electrolyte interfaces allowing higher dispersion and utilization of the deposited Pt nanoparticles. A comparative investigation was carried out using Pt–Ru nanoparticles decorated PPy–CNT composites. Cyclic voltammetry demonstrated that the synthesized Pt–Ru/PPy–CNT catalysts exhibited higher catalytic activity for methanol oxidation than Pt/PPy–CNT catalyst. Such kinds of Pt and Pt–Ru particles deposited on PPy–CNT composite polymer films exhibit excellent catalytic activity and stability towards methanol oxidation, which indicates that the composite films is more promising support material for fuel cell applications.     

FeAgMo2O8 — A novel oxygen evolution catalyst material for alkaline metal–air batteries

This paper reports about FeAgMo₂O₈ — a novel oxygen evolution catalyst material for secondary (rechargeable) metal–air batteries. Bifunctional air electrodes were made using FeAgMo₂O₈ as a charging catalyst for oxygen evolution reaction (OER) and silverized carbon black (Ag/C) was employed as a discharging catalyst for oxygen reduction reaction (ORR). Corresponding air electrodes were investigated using 10 M KOH as an electrolyte. At current densities between 20 and 50 mA per cm² we observed discharging and charging voltages of 1.20 to 1.15 V and 1.96 to 2.05 V, respectively.     

Gold nanoparticle decoration of insulating boron nitride nanosheet on inert gold electrode toward an efficient electrocatalyst for the reduction of oxygen to water

Overpotential for oxygen reduction reaction (ORR) at Au electrode is reported to be reduced by 0.27 V by the modification with boron nitride nanosheet (BNNS) but oxygen is reduced only to H₂O₂ by 2-electron process at Au electrode. Here we demonstrate that the decoration of BNNS with gold nanoparticles (AuNP) not only reduces the overpotential for ORR further by ca. 50 mV, but also opens a 4-electron reduction route to water. Both rotating disk electrode experiments with Koutecky–Levich analysis and rotating ring disk electrode measurements show that more than 50% of oxygen is reduced to water via 4-electron process at Au–BNNS/Au electrode while less than 20 and 10% of oxygen are reduced to water at the BNNS/Au and bare Au electrodes, respectively. Theoretical analysis of free energy profiles for ORR at the BN monolayer with and without Au₈ cluster placed on Au(111) shows significant stabilization of adsorbed oxygen atom by the Au₈ cluster, opening a 4-electron reduction pathway.     

A sensitivity-controlled hydrogen peroxide sensor based on self-assembled Prussian Blue modified electrode

In this communication, a hydrogen peroxide (H₂O₂) sensor based on self-assembled Prussian Blue (PB) modified electrode was reported. Thin film of PB was deposited on the electrode by self-assembly process including multiple sequential adsorption of ferric ions and hexacyanoferrate ions. The as-prepared PB modified electrode displayed sufficient stability for practical sensing application. At an applied potential of ?0.05 V vs. Ag/AgCl (sat. KCl), PB modified electrode with 30 layers exhibited a linear dependence on H₂O₂ concentration in the range of 1 × 10^?6–4 × 10^?4 M (r = 0.9998) with a sensitivity of 625 mA M^?1 cm^?2. It was found that the sensitivity of H₂O₂ sensors could be well controlled by adjusting the number of deposition cycles for PB preparation. This work demonstrates the feasibility of self-assembled PB modified electrode in sensing application, and provides an effective approach to control the sensitivity of PB-based amperometric biosensors.