Preparation, characterization and application of octadecyl modified magnesium oxide microspheres

A new solid-phase extraction sorbent, octadecyl modified magnesium oxide (C18-MgO) microspheres, was successfully prepared in the present work. Its composition, morphology and structure were studied by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), N(2) adsorption-desorption technique, and solid-state nuclear magnetic resonance (NMR). The as-synthesized C18-MgO was employed as a solid-phase extraction sorbent for the enrichment of polycyclic aromatic hydrocarbons (PAHs) in aqueous solutions. Several factors affecting the extraction efficiency of PAHs, including the type and concentration of organic modifiers, flow rate, sample volume, and the types of rinsing solvents and eluting solvents, were investigated systematically. The results demonstrated that C18-MgO was superior to MgO in terms of large volume in loading samples. In comparison with MgO and Sep-Pak C18, C18-MgO exhibited excellent extraction efficiency (>91% except for naphthalene) in respect of high recoveries under the optimized conditions. The limits of detection varied from 0.001 to 0.603 ng mL(-1) for 15 PAHs using high-performance liquid chromatography coupled with a fluorescence detector, indicating that the analytical method was highly sensitive. The proposed method was applied to enrich PAHs in tap water and acceptable recoveries (18-96%) were obtained.     

Application of matrix solid-phase dispersion in the analysis of priority polycyclic aromatic hydrocarbons in fish samples

The performance of matrix solid-phase dispersion (MSPD) for the extraction of polycyclic aromatic hydrocarbons (PAHs) in fish tissue is described. The suitability of different solid supports was tested as well as the influence on the extraction efficiency of the natural fat content in samples. Under optimal conditions 0.6-0.8 g of tissue sample, are dispersed with 2 g of octadecylsiloxane (C18) and 0.5 g of anhydrous sodium sulphate and transferred to the top of a polyethylene solid-phase extraction cartridge which already contains 2 g of florisil and 1 g of C18. Cartridges were eluted with acetonitrile. The analysis of the extracts was carried out by high-performance liquid chromatography (HPLC) coupled with fluorescence detection. The proposed method provides detection limits between 0.04 and 0.32 ng/g for the different considered PAHs, below the maximum levels established by the some regulatory bodies for the six PAHs after recent oil spill episodes and European Union regulations. Recoveries over 80% were obtained for all compounds. Accuracy validation was carried out using the US National Institute of Standards and Technology (NIST) SRM 2977 reference material.     

十八烷基离子液体杂化固相微萃取整体柱用于检测咖啡中的多环芳烃

以自制的1-十八烷基-3-(γ-三乙氧基硅基丙基)咪唑溴盐离子液体(C18IL)、二苯基二甲氧基硅烷(DDS)和四乙氧基硅烷(TEOS)为功能单体,采用溶胶-凝胶法制备了烷基咪唑基离子液体管内固相微萃取整体柱(C18IL in-tube SPME).以多环芳烃为分析对象,考察了C_(18)IL含量对C_(18)IL in-tube SPME萃取性能的影响,并对萃取条件进行了优化.建立了基于C_(18)IL in-tube SPME-气相色谱(GC-FID)的分析方法,用于检测萘、芴、菲、荧蒽和芘5种多环芳烃.该方法的检出限(S/N=3)为0.007~0.072μg/L,定量限(S/N=10)为0.023~0.24μg/L,日内和日间精密度(RSD)除菲类多环芳烃外均小于10%.将该方法用于检测咖啡中5种多环芳烃,3个不同浓度下的加标回收率为85.79%~103.42%.     

On-line preconcentration of trace carcinogenic polycyclic aromatic hydrocarbons (PAHs) in microcolumn liquid chromatography via large volume injection

The ability and efficiency of micro precolumns made of C30 particles, monolithic silica C18 stationary phase and quartz wool coated with C30, which act as novel solid phase absorbing materials, for the on-line enrichment of aqueous polycyclic aromatic hydrocarbons (PAHs) in microcolumn liquid chromatography (LC) was investigated. The enrichment unit was designed in such a way that micro precolumns were directly connected to a 6-port micro injection valve via fused-silica tubing (0.05 mm I.D.) in order to minimize band broadening of the samples, and the enrichment efficiency of the three materials was tested using 14 PAHs, which are selected by the US Environmental Protection Agency (US EPA), as the analytes. The separation of PAHs was evaluated by using laboratory-made C30 or ODS capillary columns and the results were compared. There were no significant differences showed from the separation of PAHs in terms of peak signal between the C30 and ODS capillary columns, but the C30 capillary column was chosen for the following experiment due to its ability to produce better repeatability than the ODS column. By using the three kinds of precolumn materials, results showed that the precolumn packed with C30 particles as well as the capillary monolithic C18 precolumns (0.1 or 0.2 mm I.D.) provided better recovery than those of the quartz wool's. As long as the recovery and separation of the PAHs were concerned, 0.1 mm I.D. monolithic C18 precolumn showed the best results and the R.S.D.s (N = 7) for the retention time, peak area and peak height were between 0.70-1.5, 2.3-5.8 and 2.4-6.6%, respectively. Large volume injection up to 0.5 mL, i.e. 2500-fold enrichment, was possible and no negative effect on the separation profile was found. The LOD (S/N = 3) were between 0.10 and 4.6 pg mL⁻¹, while the LOQ (S/N = 10) were in the range of 0.32-15 pg mL⁻¹, which showed that the system is comparable to many major analytical techniques and is sensitive enough for the trace analysis of PAHs in environmental samples. The system was then applied to the determination of trace PAHs present in soil sample which was randomly taken from a nearby highway.     

超声提取-气相色谱/质谱法测定皮革及纺织品中18种多环芳烃

采用超声波萃取技术对样品进行提取,气相色谱联用质谱(GC-MS)选择离子监测(SIM)模式采集数据,建立了皮革及纺织品中18种多环芳烃(PAHs)的分析方法.对色谱、质谱分析条件以及样品前处理条件进行研究与优化.在最优条件下,18种PAHs浓度在一定范围内与其峰面积呈现良好的线性关系,相关系数(R2)为0.9991～0...     

Screening and confirmation of PAHs in vegetable oil samples by use of supercritical fluid extraction in conjunction with liquid chromatography and fluorimetric detection

A fast, simple, non-destructive method for the direct screening of polycyclic aromatic hydrocarbons (PAHs) in vegetable oil samples is proposed. The method uses a supercritical fluid extraction (SFE) system coupled on-line with a fluorimetric detector to determine PAHs. This special assembly avoids the main problems encountered in the determination of PAHs in complex matrices such as vegetable oils. PAHs are selectively extracted by using silica gel in the thimble and cleaned up by passage through a C18 column. Interferences are preferentially retained by the silica gel during the SFE process while PAHs are adsorbed in the C18 column and the remainder of the matrix is sent to waste. Finally, the C18 column is purged to remove residual CO₂ gas and adsorbed PAHs are recovered by desorption with a solvent. The extracts from positive samples are subsequently analyzed by liquid chromatography (LC) with fluorescence detection. The proposed method allows the confirmation of vegetable oil safety and hence provides a new tool for consumer protection.     

Use of Ce(IV) oxidizing agent for the derivatization of polycyclic aromatic hydrocarbons for liquid chromatography-electrochemical detection.

Polycyclic aromatic hydrocarbons (PAHs) were oxidized with Ce(IV), and the resulting quinones were determined by reductive-mode liquid chromatography-electrochemical detection. This oxidation is a rapid, automatable step, involving of Ce(IV) reagent to the PAH sample and cleaning up the derivative with C18 solid-phase extraction. Using a C18 analytical column and a 2-propanol-phosphate buffer as the mobile phase, detection limits were in the ppb range for naphthalene, phenanthrene and anthracene, with linearity over 3-5 orders of magnitude. Method validation was performed by addition of the PAHs to tap water and determining the levels by reference to a calibration curve. The three PAHs can be simultaneously derivatized and determined under the same chromatographic conditions. Analysis of a motor-oil sample is also shown.     

使用C18固相萃取膜-色质联用定量分析饮用水中痕量多环芳烃的初步研究

参照美国EPA525.1方法,C18-固相萃取膜萃取饮用水中的有机物,利用GC/MS法鉴定多环芳烃(PAHs),使用16种多环芳烃混合标准样绘制标准曲线,以内标法对PAHs进行定量分析.采用本方法研究某水厂经过深度处理后的出厂水中的7种多环芳烃的含量,PAHs的平均回收率为94.0%～97.7%.检测限为0.001μg/L.     

气相色谱-质谱法测定热塑性弹性体中的多环芳烃

建立了一种简单、准确的测定热塑性弹性体中16种多环芳烃(PAHs)的气相色谱-质谱(GC-MS)方法。考察了样品制备、萃取溶剂、萃取方法、时间以及温度对厂家制备的阳性热塑性弹性体样品中PAHs提取效率的影响,确定了萃取条件和方法。样品经甲苯超声萃取、浓缩后用环己烷溶解、二甲亚砜液液萃取净化后采用GC-MS进行分析,内标法定量。通过对不同材质阳性热塑性弹性体样品的加标回收、精密度试验等对建立的方法进行评价,16种PAHs的平均回收率为70%～117%,精密度为0.2%～10.8%。该方法适合于热塑性弹性体中PAHs的测定。     

Determination of polycyclic aromatic hydrocarbons in water by solid-phase microextraction and liquid chromatography.

This study describes the determination of polycyclic aromatic hydrocarbons (PAHs) in water using high-performance liquid chromatography (HPLC) coupled with fluorescence detection (FLD). Because individual PAHs are generally present in water only at trace levels, a sensitive and accurate determination technique is essential. The separation and detection of five PAHs were run completely within 25 min by the HPLC/FLD system with an analytical C18 column, a fluorescence detection, and acetonitrile-water gradient elution. Calibration graphs were linear with very good correlation coefficients (r > 0.9998), and the detection limits were in the range of 2-6 ng/l for five PAHs. Solid phase microextraction (SPME) was performed for sample pretreatment prior to HPLC-FLD determination, and the governing parameters were investigated. Compared to conventional methods, SPME has high recovery, saves considerable time, and reduces solvents waste. The extraction efficiencies of five PAHs were above 88% and the extraction times were 35 min in one pretreatment procedure. One particular discovery is that 1.5 M sodium monochloroactate (ClCH2COONa) can improve the extraction yield of PAH compounds more than other inorganic salts. The SPME-HPLC-FLD technique provides a relatively simple, convenient, practical procedure, which was here successfully applied to determine five PAHs in water from authentic water samples.     

Solid-phase extraction with C30 bonded silica for analysis of polycyclic aromatic hydrocarbons in airborne particulate matters by gas chromatography-mass spectrometry

A solid-phase extraction (SPE) method using triacontyl bonded silica (C30) as sorbent was developed for the determination of 16 US Environmental Protection Agency polycyclic aromatic hydrocarbons (PAHs) in airborne particulate matters quantitatively by gas chromatography-mass spectrometry (GC-MS). Optimization experiments were conducted using spiked standard aqueous solution of PAHs and real airborne particulates samples aiming to obtain highest SPE recoveries and extraction efficiency. Factors were studied in SPE procedures including the concentration of organic modifier, flow rate of sample loading and elution solvents. The ultrasonication time and solvents were also investigated. Recoveries were in the range of 68-107% for standard PAHs aqueous solution and 61-116% for real spiked sample. Limits of detection (LODs) and limits of quantification (LOQs) with standard solution were in the range of 0.0070-0.21 microgL(-1) and 0.022-0.67 microgL(-1), respectively. The optimized method was successfully applied to the determination of 16 PAHs in real airborne particulate matters.     

The determination of polycyclic aromatic hydrocarbons in human urine by high‐resolution gas chromatography–mass spectrometry

Polycyclic aromatic hydrocarbons (PAHs), organic compounds formed by at least two condensed aromatic rings, are ubiquitous environmental pollutants that are produced by incomplete combustion of organic materials. PAHs have been classified as carcinogenIC to humans by the International Agency for Research on Cancer, because they can bind to DNA, causing mutations. Therefore, the levels of PAHs in human urine can be used as an indicator for potential carcinogenesis and cell mutation. An analytical method was developed for the accurate measurement of PAHs in urine using high‐resolution gas chromatography–mass spectrometry. Urine samples were extracted by an Oasis HLB extraction cartridge after enzymatic hydrolysis with a β‐glucuronidase/arylsulfatase cocktail. The 18 PAHs were separated using an Agilent DB‐5 MS capillary column (30 m × 0.25 mm, 0.25 μm) and monitored by time‐of‐flight mass spectrometry. Under the optimized method, the linearity of calibration curves was >0.994. The limits of detection at a signal‐to‐noise ratio of 3 were 10–100 ng/L. The coefficients of variation were in the range of 0.4–9.0%. The present method was highly accurate for simultaneous determination of 18 PAHs in human urine and could be applied to monitoring and biomedical investigations to check exposure of PAHs.     

Monitoring of PAHs in air by collection on XAD-2 adsorbent then microwave-assisted thermal desorption coupled with headspace solid-phase microextraction and gas chromatography with mass spectrometric detection

Microwave-assisted thermal desorption (MAD) coupled to headspace solid-phase microextraction (HS-SPME) has been studied for in-situ, one-step, sample preparation for PAHs collected on XAD-2 adsorbent, before gas chromatography with mass spectrometric detection. The PAHs on XAD-2 were desorbed into the extraction solution, evaporated into the headspace by use of microwave irradiation, and absorbed directly on a solid-phase microextraction fiber in the headspace. After desorption from the SPME fiber in the hot GC injection port, PAHs were analyzed by GC–MS. Conditions affecting extraction efficiency, for example extraction solution, addition of salt, stirring speed, SPME fiber coating, sampling temperature, microwave power and irradiation time, and desorption conditions were investigated. Experimental results indicated that extraction of 275 mg XAD-2, containing 10–200 ng PAHs, with 10-mL ethylene glycol–1 mol L⁻¹ NaCl solution, 7:3, by irradiation with 120 W for 40 min (the same as the extraction time), and collection with a PDMS–DVB fiber at 35 °C, resulted in the best extraction efficiency. Recovery was more than 80% and RSD was less than 14%. Optimum desorption was achieved by heating at 290 °C for 5 min. Detection limits varied from 0.02 to 1.0 ng for different PAHs. A real sample was obtained by using XAD-2 to collect smoke from indoor burning of joss sticks. The amounts of PAHs measured varied from 0.795 to 2.53 ng. The method is a simple and rapid procedure for determination of PAHs on XAD-2 absorbent, and is free from toxic organic solvents.     

Rhodaelectrocatalysis for Annulative C−H Activation: Polycyclic Aromatic Hydrocarbons through Versatile Double Electrocatalysis

Rapid access to structurally diversified polycyclic aromatic hydrocarbons (PAHs) in a controlled manner is of key significance in materials sciences. Herein, we describe a strategy featuring two distinct electrocatalytic C?H transformations for the synthesis of novel nonplanar PAHs. The combination of rhodaelectrooxidative C?H activation/[2+2+2] alkyne annulation of easily accessible boronic acids with electrocatalytic cyclodehydrogenation provided modular access to diversely substituted PAHs with electricity as a sustainable oxidant. The unique molecular topology as well as the photophysical and electronic properties of the thus obtained PAHs were fully analyzed. The unique power of this metallaelectrocatalysis method was demonstrated by the chemoselective assembly of synthetically useful iodo‐substituted PAHs.     

Supercritical fluid clean-up of environmental samples for the analysis of polycyclic aromatic hydrocarbons using time-of-flight secondary ion mass spectrometry.

A novel sample-pretreatment method for time-of-flight secondary ion mass spectrometry (TOF-SIMS) was developed using supercritical fluid extraction (SFE). In SFE, the extraction efficiency of a certain organic matter is controlled by the pressure and temperature of supercritical CO2. Two-step SFE (1st step at 10 Mpa, 40 degrees C; 2nd step at 30 MPa, 120 degrees C) was applied to diesel exhaust particles containing many kinds of n-alkanes and aromatic species. n-Alkanes and polycyclic aromatic hydrocarbons (PAHs) were extracted in the 1st and 2nd steps, respectively. This selectivity was utilized for the sample preparation of TOF-SIMS analysis. Diesel exhaust particles after the 1st step of extraction were analyzed with TOF-SIMS, aiming at PAHs as analytical targets. The obtained spectrum was simplified, and mass peaks of individual PAHs were easily assigned, because unwanted compounds, like n-alkanes, were selectively removed by SFE. Furthermore, a simple calculation elucidated the outline of the spectrum.     

Quantification of 13 priority polycyclic aromatic hydrocarbons in human urine by headspace solid-phase microextraction gas chromatography-isotope dilution mass spectrometry

Polycyclic aromatic hydrocarbons (PAHs) are common environmental pollutants in both living and working environments. The aim of this study was the development of a headspace solid-phase microextraction gas chromatography-isotope dilution mass spectrometry (HS-SPME/GC-IDMS) method for the simultaneous quantification of 13 PAHs in urine samples. Different parameters affecting PAHs extraction by HS-SPME were considered and optimized: type/thickness of fiber coatings, extraction temperature/time, desorption temperature/time, ionic strength and sample agitation. The stability of spiked PAHs solutions and of real urine samples stored up to 90 days in containers of different materials was evaluated. In the optimized method, analytes were absorbed for 60 min at 80 °C in the sample headspace with a 100 μm polydimethylsiloxane fiber. The method is very specific, with linear range from the limit of quantification to 8.67 × 10³ ng L⁻¹, a within-run precision of <20% and a between-run precision of <20% for 2-, 3- and 4-ring compounds and of <30% for 5-ring compounds, trueness within 20% of the spiked concentration, and limit of quantification in the 2.28-2.28 × 10¹ ng L⁻¹ range. An application of the proposed method using 15 urine samples from subjects exposed to PAHs at different environmental levels is shown.     

Analysis of 27 polycyclic aromatic hydrocarbons by matrix solid-phase dispersion and isotope dilution gas chromatography-mass spectrometry in sewage sludge from the Spanish area of Madrid

A method for the determination of 27 polycyclic aromatic hydrocarbons (PAHs) in sludge from wastewater treatment plants (WWTPs) located in urban, industrial or rural zones is presented. PAHs were extracted by matrix solid-phase dispersion (MSPD) assisted by sonication. Purification of extracts was carried out by solid-phase extraction with C(18) and PAHs were eluted with acetonitrile. PAHs were determined by isotope dilution gas chromatography with electron impact mass spectrometric detection in the selected ion-monitoring mode (GC-MS-SIM), using deuterated PAHs as internal standards. The limits of detection ranged from 0.03 ng/g for acenaphthylene to 0.45 ng/g for benzo[b]naphtho[2,1-d]thyophene. After optimization, the method was validated with a certified reference sludge. The proposed analytical method was applied to determine PAH levels in sewage sludge samples collected from 19 water treatment plants located in the province of Madrid (Spain). In most of the examined samples, phenanthrene was the main compound with a mean concentration of 1062 ng/g. PAHs were detected in all of the samples, with total concentrations between 390 and 6390 ng/g dry weight for the 27 PAHs analyzed and from 310 to 5120 ng/g dry weight for the sum of the 10 PAHs considered in the draft European Union directive.     

Determination of polycyclic aromatic hydrocarbons in aqueous samples by microwave assisted headspace solid-phase microextraction and gas chromatography/flame ionization detection

The novel pretreatment technique, microwave-assisted heating coupled to headspace solid-phase microextraction (MA-HS-SPME) has been studied for one-step in situ sample preparation for polycyclic aromatic hydrocarbons (PAHs) in aqueous samples before gas chromatography/flame ionization detection (GC/FID). The PAHs evaporated into headspace with the water by microwave irradiation, and absorbed directly on a SPME fiber in the headspace. After being desorbed from the SPME fiber in the GC injection port, PAHs were analyzed by GC/FID. Parameters affecting extraction efficiency, such as SPME fiber coating, adsorption temperature, microwave power and irradiation time, and desorption conditions were investigated.Experimental results indicated that extraction of 20 mL aqueous sample containing PAHs at optional pH, by microwave irradiation with effective power 145 W for 30 min (the same as the extraction time), and collection with a 65 μm PDMS/DVB fiber at 20 °C circular cooling water to control sampling temperature, resulted in the best extraction efficiency. Optimum desorption of PAHs from the SPME fiber in the GC hot injection port was achieved at 290 °C for 5 min. The method was developed using spiked water sample such as field water with a range of 0.1-200 μg/L PAHs. Detection limits varied from 0.03 to 1.0 μg/L for different PAHs based on S/N = 3 and the relative standard deviations for repeatability were <13%. A real sample was collected from the scrubber water of an incineration system. PAHs of two to three rings were measured with concentrations varied from 0.35 to 7.53 μg/L. Recovery was more than 88% and R.S.D. was less than 17%. The proposed method is a simple, rapid, and organic solvent-free procedure for determination of PAHs in wastewater.     

Rapid determination of polycyclic aromatic hydrocarbons in tea infusion samples by high-performance liquid chromatography and fluorimetric detection based on solid-phase extraction

This paper describes a method for the determination of PAHs in black, green and decaffeinated tea infusion samples. The method is based on the solid phase extraction of the PAHs using Sep-Pak vac tC-18 cartridges. The PAHs are then eluted from the cartridges with dichloromethane. Quantification and detection are carried out by HPLC with a fluorimetric detector using a program of excitation and emission wavelength pairs. Recoveries at concentration levels in the range 190-1790 ng l-1 were higher than 65% for all PAHs except dibenz[a,h]anthracene, for which it was around 54%. The mean content of PAHs was in the range 28.7-112 ng l-1 in the tea infusions, with relative standard deviations between 2 and 18% (n = 4).     

Determination of 16 polycyclic aromatic hydrocarbons in environmental water samples by solid-phase extraction using multi-walled carbon nanotubes as adsorbent coupled with gas chromatography–mass spectrometry

A solid-phase extraction (SPE) using multi-walled carbon nanotubes (MWCNTs) as adsorbent coupled with gas chromatography–mass spectrometry (GC–MS) method was developed for the determination of 16 polycyclic aromatic hydrocarbons (PAHs) in environmental water samples. Several condition parameters, such as extraction adsorbents, elution solvents and volumes, and sample loading flow rate and volume were optimized to obtain high SPE recoveries and extraction efficiency. 150 mg MWCNTs as sorbent presented high extraction efficiency of 16 PAHs due to the large specific surface area and high adsorption capacity of MWCNTs compared with the commercial C18 column (250 mg/2 mL). The calibration curves of 16 PAHs extracted were linear in the range of 20–5000 ng L⁻¹, with the correlation coefficients (r²) between 0.9848 and 0.9991. The method attained good precisions (relative standard deviation, RSD) from 1.2% to 12.1% for standard PAHs aqueous solutions; method recoveries ranged in 76.0–125.5%, 74.5–127.0%, and 70.0–122.0% for real spiked samples from river water, tap water and seawater, respectively. Limits of detection (LODs, S/N = 3) of the method were determined from 2.0 to 8.5 ng L⁻¹. The optimized method was successfully applied to the determination of 16 PAHs in real environmental water samples.