Magnetic properties of xNi0.53Cu0.12Zn0.35Fe1.88O4+(1−x)BaTiO3 nanocomposites

The nanocrystalline Ni_0.53Cu_0.12Zn_0.35Fe_1.88O₄ and BaTiO₃ powders were prepared using Microwave-Hydrothermal (M-H) method at 160 °C/45 min. The as synthesized powders were characterized using the X-ray diffraction (XRD) and Transmission Electron Microscope (TEM). The size of the powders that were synthesized using M-H system was found to be ∼30 and ∼50 nm for ferrite phase and ferroelectric phases, respectively. The powders were densified using microwave sintering method at 900 °C/30 min. The ferrite and ferroelectric phases were observed from XRD and morphology of the composites was observed with the Scanning Electron Microscope (SEM).The magnetic hysteresis loops were recorded using the Vibrating Sample Magnetometer (VSM).The frequency dependence of real (μ′) and imaginary (μ″) parts of permeability was measured in the range of 1 MHz-1.8 GHz. The permeability decreases with an increase of BaTiO₃ content at 1 MHz. The transition temperature (T_C) of ferrite was found to be 245 °C. The T_C of composite materials decreases with an increase in BaTiO₃ content.     

Synthesis and magnetic properties of Au-coated amorphous Fe20Ni80 nanoparticles

Gold-coated nanoparticles of Fe₂₀Ni₈₀ (permalloy) have been synthesized by a microemulsion process. The as-prepared samples consist of ∼5 nm diameter particles of amorphous Fe₂₀Ni₈₀ that are likely encapsulated in B₂O₃. One or more Fe₂₀Ni₈₀@B₂O₃ particles are subsequently encapsulated in 8-20 nm gold nanospheres, as determined by TEM and X-ray powder diffraction (XRD) line broadening. The gold shells were found to be under expansive strain. Magnetic data confirm the existence of a superparamagnetic phase with a blocking temperature, T_B, of ∼33 K. The saturation magnetization, M_S, of the as-prepared, Au-coated sample is ∼65 emu g⁻¹ at 5 K and ∼16 emu g⁻¹ at 300 K. The coercivity, H_C, is ∼280 Oe at 5 K.     

Large negative magnetoresistance in thiospinel CuCrZrS4

We report on large negative magnetoresistance observed in ferromagnetic thiospinel compound CuCrZrS₄. The electrical resistivity increased with decreasing temperature according to the exp(T₀/T)^1/2, an expression derived from variable range hopping with strong electron-electron interaction. The resistivity under a magnetic field was expressed by the same form with the characteristic temperature T₀ decreasing with increasing magnetic field. Magnetoresistance ratio ρ(T,0)/ρ(T,H) is 1.5 for H=90 kOe at 100 K and increases divergently with decreasing temperature reaching 80 at 16 K. Results of magnetization measurements are also presented. A possible mechanism of the large magnetoresistance is discussed.     

Superparamagnetism and spin-glass like state for the MnFe2O4 nano-particles synthesized by the thermal decomposition method

MnFe₂O₄ nano-particles with an average size of about 7 nm were synthesized by the thermal decomposition method. Based on the magnetic hysteresis loops measured at different temperatures the temperature-dependent saturation magnetization (M_S) and coercivity (H_C) are determined. It is shown that above 20 K the temperature-dependence of the M_S and H_C indicates the magnetic behaviors in the single-domain nano-particles, while below 20 K, the change of the M_S and H_C indicates the freezing of the spin-glass like state on the surfaces. By measuring the magnetization–temperature (M–T) curves under the zero-field-cooling (ZFC) and field-cooling procedures at different applied fields, superparamagnetism behavior is also studied. Even though in the ZFC M–T curves peaks can be observed below 160 K, superparamagnetism does not appear until the temperature goes above 300 K, which is related with the strong inter-particle interaction.     

Structural, magnetic and magnetocaloric properties of La0.7−xEuxBa0.3MnO3 perovskites

Polycrystalline perovskite manganites La_0.7−xEu_xBa_0.3MnO₃(x=0.05, 0.1 and 0.15) were prepared by sol-gel method. The prepared samples remain single phase with a perovskite structure, revealed by X-ray diffraction. The structure refinement of La_0.7−xEu_xBa_0.3MnO₃(x=0.05, 0.1 and 0.15) samples was performed in the hexagonal setting of the R3¯c space group. The dependence of magnetization M on applied magnetic field H and temperature T was measured carefully near the Curie temperature T_C for all the samples. With the increasing Eu content, both the unit cell volume and Curie temperature T_C of 298 K has been detected with a maximum of magnetic entropy |ΔS_M^max| for the La_0.7−xEu_xBa_0.3MnO₃ with x=0.15, reaching a value of 2.3 J/kg K when a magnetic field of 10 kOe was applied and the relative cooling power (RCP) is 46 J/kg. These results suggest that the material may be a suitable candidate as working substance in magnetic refrigeration near room temperature.     

Structure and magnetic entropy change of suck-cast Gd60Co26Al6Ge8 alloy

The Gd₆₀Co₂₆Al₆Ge₈ alloy has been prepared by the copper-mold suck-casting and its phase component has been investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive spectroscopy (EDS). It is shown that this alloy consists of primary crystalline Gd₅Ge₃ phase and amorphous matrix. The glass transition temperature (T_g) and crystallization temperatures (T_x) occur at 292 and 320 °C, respectively. The maximal magnetic entropy change (ΔS_M) under 0-5 T field is about 7.6 J (kg⁻¹ K⁻¹) at 155 K and the refrigeration capacity (RC) is about 768 J kg⁻¹, which makes Gd₆₀Co₂₆Al₆Ge₈ bulk metallic glass matrix composite a promising candidate for magnetic refrigerant.     

Influence of Dy addition on the magnetocaloric effect of La0.67Ca0.33Mn0.9V0.1O3 ceramics

The influence of partial substitution of La by Dy on the magnetocaloric response of (La_1−xDy_x)_0.67Ca_0.33Mn_0.9V_0.1O₃, where x=0.03, 0.15 and 0.25 is studied. Rietveld refinement of X-ray diffraction pattern using GSAS method shows that the compounds adopt the orthorhombic structure with Pnma space group. The systematic change in lattice parameters and magnetic phase transition indicates the substitution effect of Dy. From the magnetization isotherms at different temperatures, magnetic entropy change close to their respective transition temperatures (T_C) has been evaluated. The maximum value of entropy change near T_C is found to be about 4.8 J/kg K at 187.5 K for LCMVDy_0.03, 2.45 J/kg K at 107.5 K for LCMVDy_0.15 and 2.15 J/kg K at 92.5 K for LCMVDy_0.25 at 4 T. Dy addition produces a reduction in T_C and in magnitude of the magnetic entropy change. Even though the entropy change decreases with increasing Dy substitution the refrigerant temperature range, ΔT, is found to be 10 K for LCMVDy_0.03, 31 K for LCMVDy_0.15 and 35 K for LCMVDy_0.25 compounds [90%] at 4 T. The field dependence of the magnetic entropy change is also analyzed showing the power law dependence, ΔS_M∞Hⁿ where n=0.75(2) for LCMVDy_0.03, n=0.80(4) for LCMVDy_0.15 and n=0.92(8) for LCMVDy_0.25 compounds at their respective transition temperatures. The relative cooling power and its field dependance are also analyzed.     

Synthesis and characterization of Co7(OH)12(C2H4S2O6)(H2O)2—a single crystal structural study of a ferrimagnetic layered cobalt hydroxide

A novel layered hydrotalcite-like material, Co₇(H₂O)₂(OH)₁₂(C₂H₄S₂O₆), has been prepared hydrothermally and the structure determined using single crystal X-ray diffraction (a=6.2752(19) Å, b=8.361(3) Å, c=9.642(3) Å, α=96.613(5)°, β=98.230(5)°, γ=100.673(5)°, R1=0.0551). The structure consists of brucite-like sheets where 1/6 of the octahedral sites are replaced by two tetrahedrally coordinated Co(II) above and below the plane of the layer. Ethanedisulfonate anions occupy the space between layers and provide charge balance for the positively charged layers. The compound is ferrimagnetic, with a Curie temperature of 33 K, Curie-Weiss θ of −31 K, and a coercive field of 881 Oe at 5 K.     

Structural, microstructural and magnetic properties of NiFe2O4, CoFe2O4 and MnFe2O4 nanoferrite thin films

The structural, microstructural and magnetic properties of nanoferrite NiFe₂O₄ (NF), CoFe₂O₄ (CF) and MnFe₂O₄ (MF) thin films have been studied. The coating solution of these ferrite films was prepared by a chemical synthesis route called sol-gel combined metallo-organic decomposition method. The solution was coated on Si substrate by spin coating and annealed at 700 °C for 3 h. X-ray diffraction pattern has been used to analyze the phase structure and lattice parameters. The scanning electron microscopy (SEM) and atomic force microscopy (AFM) have been used to show the nanostructural behavior of these ferrites. The values of average grain's size from SEM are 44, 60 and 74 nm, and from AFM are 46, 61 and 75 nm, respectively, measured for NF, CF and MF ferrites. At room temperature, the values of saturation magnetization, M_s∼50.60, 33.52 and 5.40 emu/cc, and remanent magnetization, M_r∼14.33, 15.50 and 1.10 emu/cc, respectively, are observed for NF, CF and MF. At low temperature measurements of 10 K, the anisotropy of ferromagnetism is observed in these ferrite films. The superparamagnetic/paramagnetic behavior is also confirmed by χ′(T) curves of AC susceptibility by applying DC magnetizing field of 3 Oe. The temperature dependent magnetization measurements show the magnetic phase transition temperature.     

Influence of magnetic impurities on superconducting property of polycrystalline iron-based NdFeAsO0.88F0.12

Polycrystalline iron-based superconducting NdFeAsO_0.88F_0.12 was prepared via solid-state reaction in ambient pressure. Small amounts of ferromagnetic impurities were detected by Scanning Electron Microscopy (SEM) analysis. To study the influence of magnetism on superconducting properties of the sample, magnetization M(T, H) measurements were performed in fields up to 1.5 T and in the temperature range of 5-60 K. The abnormal behavior was observed in the χ(T) curves, and the magnetization hysteresis loops (MHLs) can be described by a sum of the contributions of superconductive hysteresis, ferromagnetic hysteresis of the impurities and the paramagnetic background of the isolated Nd³⁺ ions. The influence of the ferromagnetic impurities and the paramagnetic background were investigated and discussed. After the corrections of the magnetism contributions, the intrinsic superconductive MHLs as well as the critical current density were obtained.     

Synthesis and physical characterization of superconductivity-magnetism crossover compound RuSr2EuCeCu2O10−δ

We carefully studied the nonsuperconducting sample of the magneto-superconducting RuSr₂(Eu_1−xCe_x)Cu₂O_10−δ series with composition RuSr₂EuCeCu₂O_10−δ. This compound seems to exhibit a complex magnetic state as revealed by host of techniques like resistivity, thermopower, magnetic susceptibility, and MR measurements. The studied compound exhibited ferromagnetic like M(H) loops at 5, 20, and 50 K, and semiconductor like electrical conduction down to 5 K, with −MR^7 T of up to 4% at low temperatures. The −MR^7 T decreases fast above 150 K and monotonically becomes close to zero above say 230 K. Below, 150 K −MR^7 T decreases to around 3% monotonically down to 75 K, with further increase to 4% at around 30 K and lastly having a slight decrease below this temperature. The thermopower S(T) behavior closely followed the −MR^7 T steps in terms of d(S/T)/dT slopes. Further, both MR^7 T steps and d(S/T)/dT slopes are found in close vicinity to various magnetic ordering temperatures (T_mag) of this compound.     

Effect of refractory metals addition on the structural and magnetic properties of Pr3(Fe, Co, Ti)29 system

Polycrystalline refractory metal-substituted Pr₃(Fe_0.6M_0.1Co_0.3)_27.5Ti_1.5 (M=V, Ti, Zr, Mo, Nb,Cr) and Pr₃(Fe_0.5Co_0.5)_27.5Ti_1.5 have been studied for high-temperature permanent magnetic materials. X-ray diffraction showed the main phase to be the 3:29 phase. We observed the highest reported T_C (Curie temperature) of 640 °C for the 3:29 system in the Pr₃(Fe_0.5Co_0.5)_27.5Ti_1.5. In the refractory metal-substituted systems, the highest T_C of 480 °C was observed for the Nb-substituted alloy. SEM measurements showed that Ti in Pr₃(Fe_0.6Ti_0.1Co_0.3)_27.5Ti_1.5 is deposited near the grain boundary. H_A (anisotropy energy) of V-substituted alloy is as high as 72 kOe, the highest reported in the 3:29 system and is ∼200% higher than 24 kOe observed in Pr₃(Fe_0.7Co_0.3)_27.5Ti_1.5. Cr and Ti substitutions show an increase of 65% (40 kOe) and 45% (35 kOe) in H_A respectively. M_S (saturation magnetization) values were ∼100 emu/g and are lower than that observed in Pr₃(Fe_0.7Co_0.3)_27.5Ti_1.5.     

Magnetic properties for the Mn2GeTe4 compound

Measurements of magnetic susceptibility χ, in the temperature range from 2 to 300 K, and of magnetization M vs. applied magnetic field B, up to 5 T, at various temperatures were made on polycrystalline samples of the Mn₂GeTe₄ compound. It was found that Mn₂GeTe₄ has a Néel temperature T_N of about 135 K, shows mainly antiferromagnetic behavior with a very weak superimposed ferromagnetic component that is attributed to spin canting. Also, the magnetic results suggest that a possible spin-glass transition takes place at T_f≈45 K. The spin-glass order parameter q(T), determined from the susceptibility data, was found to be in agreement with the prediction of conventional spin-glass theory. The M vs. B results indicated that bound magnetic polarons (BMPs) occur in the compound, and that the effects from BMPs disappear at approximately 80 K. The M vs. B curves were well fitted by a Langevin type of equation, and the variation of the fitting parameters determined as a function of temperature. Using a simple spherical model, the radius of the BMP in the material was found to be about 27 Å; this value is similar to the effective Bohr radius for an acceptor in the II-IV-V₂ and I-III-VI₂ ternary semiconductor compounds.     

Magnetocaloric effect in high Ni content Ni52Mn48−xInx alloys under low field change

Ni-rich Heusler alloys Ni₅₂Mn_48−xIn_x (x=15.5, 16 and 16.5) were prepared by the arc melting method. X-ray diffraction analysis revealed that the martensite has orthorhombic structure (S.G. Pmm2) at room temperature. The only alloy with x=15.5 has structural transmission from martensite to austenite without any magnetic transmission. The temperature dependence and the field dependence of the magnetization measurement indicated that the magnetization increased with the decreasing of the concerntration of Mn. The lesser the Mn atoms located in the In atom sites, the weaker the total AFM interaction in the system. Giant entropy changes ΔS_M(T, H) were found in Ni₅₂Mn_48−xIn_x alloys with the maximum ΔS_M value of 22.3 J kg K for the sample with x=16.5 at 270 K under the magnetic field change of 1.5 T.     

Study of cerium doped magnetite (Fe3O4:Ce)/PMMA nanocomposites

The paper presents the synthesis and properties of polymer nanocomposite material based on cerium doped magnetite (Fe₃O₄) as filler material and poly methyl methacrylate (PMMA) as host matrix. The magnetite (Fe₃O₄) particles were synthesized by co-precipitation route using stable ferrous and ferric salts with ammonium hydroxide as precipitating agent. Further, they doped by cerium oxide (CeO₂) non-stoichiometrically. The composite material was fabricated by solvent evaporation method. Here 2.4 GHz microwaves were used to study the effect of microwaves heating on polymerization. The phase and crystal structure is determined by X-ray diffraction (XRD). The average crystallite size of the composites varies from 28 to 35 nm. The chemical structure is confirmed by Fourier transform infrared (FTIR) spectroscopy. The magnetic and thermal properties are investigated by vibrating sample magnetometer (VSM) and differential scanning calorimetry (DSC). The thermal study shows that the microwave heated samples possess higher glass transition temperature (T_g). The magnetic results suggest that coercivity (H_C) and squareness (M_r/M_s) of the loop increases with increasing doping percent of cerium.     

Magnetic ordering in CeMnCuSi2

Temperature and field-dependent magnetization measurements on polycrystalline CeMnCuSi₂ reveal that the Mn moments in this compound exhibit ordering with a ferromagnetic (FM) component ordered instead of the previously reported purely antiferromagnetic (AFM) ordering. The FM ordering temperature, T_c, is about 120 K and almost unchanged with external fields up to 50 kOe. Furthermore, an AFM component (such as in a canted spin structure) is observed to be present in this phase, and its orientation is modified rapidly by the external magnetic field. The Ce L₃-edge X-ray absorption result shows that the Ce ions in this compound are nearly trivalent, very similar to that in the heavy fermion system CeCu₂Si₂. Large thermomagnetic irreversibility is observed between the zero-field-cooled (ZFC) and field-cooled (FC) M(T) curves below T_c indicating strong magnetocrystalline anisotropy in the ordered phase. At 5 K, a metamagnetic-type transition is observed to occur at a critical field of about 8 kOe, and this critical field decreases with increasing temperature. The FM ordering of the Mn moments in CeMnCuSi₂ is consistent with the value of the intralayer Mn–Mn distance R^a_Mn–Mn=2.890 Å, which is greater than the critical value 2.865 Å for FM ordering. Finally, a magnetic phase diagram is constructed for CeMnCuSi₂.     

Structural and magnetic properties of Co1−xZnxFe2O4 nanoparticles by co-precipitation method

Co_1−xZn_xFe₂O₄ nanoparticles were prepared by co-precipitation method with x varying from 0 to 1.0. The powder samples were characterized by X-ray diffraction (XRD), vibrating sample magnetometer (VSM) and Fourier transform infrared spectroscopy (FTIR). The average crystallite sizes of the particles were determined from XRD. X-ray analysis showed that the samples were cubic spinel. The average crystallite size (D_aveXR) of the particles precipitated was found to vary from 6.92 to 12.02 nm decreasing with the increase in zinc substitution. The lattice constant (a_o) increased with the increase in zinc substitution. The specific saturation magnetization (M_S) of the particles was measured at room temperature. The magnetic parameters such as M_S, H_c, and M_r were found to decrease with the increase in zinc substitution. FTIR spectra of the Co_1−xZn_xFe₂O₄ with x varying from 0 to 1.0 in the range 400–4000 cm⁻¹ were reported. The spinel structure and the crystalline water adsorption of Co_1−xZn_xFe₂O₄ nanoparticles were studied by using FTIR.     

Theoretical study on the kinetics for OH reactions with CH3OH and C2H5OH

Kinetics and mechanisms for reactions of OH with methanol and ethanol have been investigated at the CCSD(T)/6-311 + G(3df, 2p)//MP2/6-311 + G(3df, 2p) level of theory. The total and individual rate constants, and product branching ratios for the reactions have been computed in the temperature range 200-3000 K with variational transition state theory by including the effects of multiple reflections above the wells of their pre-reaction complexes, quantum-mechanical tunneling and hindered internal rotations. The predicted results can be represented by the expressions k₁ = 4.65 × 10⁻²⁰ × T^2.68 exp(414/T) and k₂ = 9.11 × 10⁻²⁰ × T^2.58 exp(748/T) cm³ molecule⁻¹ s⁻¹ for the CH₃OH and C₂H₅OH reactions, respectively. These results are in reasonable agreements with available experimental data except that of OH + C₂H₅OH in the high temperature range. The former reaction produces 96-89% of the H₂O + CH₂OH products, whereas the latter process produces 98-70% of H₂O + CH₃CHOH and 2-21% of the H₂O + CH₂CH₂OH products in the temperature range computed (200-3000 K).     

Field-induced structural transition and the related magnetic entropy change in Ni43Mn43Co3Sn11 alloy

Magnetic properties and magnetic entropy change ΔS were investigated in Heusler alloy Ni₄₃Mn₄₃Co₃Sn₁₁. With decreasing temperature this alloy undergoes a martensitic structural transition at T_M=188 K. The incorporation of Co atoms enhances ferromagnetic exchange for parent phases. Austenitic phase with cubic structure shows strong ferromagnetic behaviors with Curie temperature T_C^A at 346 K, while martensitic phase shows weak ferromagnetic properties. An external magnetic field can shift T_M to a lower temperature at a rate of 4.4 K/T, and a field-induced structural transition from martensitic to austenitic state takes place at temperatures near but below T_M. As a result, a great magnetic entropy change with positive sign appears. The size of ΔS reaches 33 J/kg K under 5 T magnetic field. More important is that the ΔS displays a table-like peak under 5 T, which is favorable for Ericsson-type refrigerators.