Xenon-ion Induced Magnetic and Structural Modifications of Ferromagnetic Alloys

Thin polycrystalline films of permalloy (Ni₇₉Fe₂₁) and permendur (Co₅₀Fe₅₀) have been irradiated with Xe-ions to fluences of 10¹⁴–10¹⁶ ions/cm². Ion-induced structural and magnetic modifications have been measured by grazing angle X-ray diffraction, Rutherford backscattering and magneto-optical Kerr effect. In the case of permendur, the Xe-ion implantation first reduced the coercivity, because of stress relaxation, while higher ion fluences increased the coercivity due to pinning centers generated in the film. The ion irradiation aligned the in-plane easy axis of the magnetization along the direction of the external magnetic field during implantation. Phase shifts obtained from magnetic force microscopy confirmed these modifications. The effects of Xe-ion irradiation in permalloy films are much weaker and underline the importance of magnetostriction in the variation of the coercivity and anisotropy.     

Current density effect on magnetic properties of nanocrystalline electroplated Ni80Fe20/Cu composite wires

In developing high-sensitivity micro sensors for very weak magnetic field, extremely high permeability magnetic material is essential for the sensing element. In this study, the effect of plating current density in nanocrystalline electrodeposition of permalloy on the crystal grain size and consequently on the soft magnetic properties of the deposited layer of Ni₈₀Fe₂₀/Cu composite wire is investigated. It is found that the coercivity of the deposited Ni₈₀Fe₂₀ increases and the MI effect ratio of the Ni₈₀Fe₂₀/Cu wire decreases with increasing current density in the lower range of current density (0.6–2 A/dm²) while the opposite trend is observed as the current density range increases in a higher range (2–8 A/dm²). It seems that increasing plating current density has the effect of decreasing the crystal grain size of the plated material, resulting in lower coercivity of the plated material. This effect, due to decreased grain size, is dominating in the higher range of plating current density. However, it also has the effect of increasing residual stresses in the plated material, which is dominating in the lower range of plating current density, resulting in higher coercivity of the plated materials.     

NiFeNb种子层对坡莫合金磁滞回线的影响

以NiFeNb为种子层，制备(Ni₇₉Fe₂₁)_1-xNb_{x(5nm)/(Ni79Fe21) (20nm)/Ta(3nm)系列膜，并对其颗粒大小、 磁滞回线及表面粗糙度等进行测量，探讨种子层中Nb含量x对坡莫合金磁滞回线的影响.结果 表明，以NiFeNb作种子层能更好地改善坡莫合金的微结构. Nb含量为23％时的磁滞回线有最 小的最大磁能积、矫顽力.种子层影响坡莫合金磁滞回线的一个重要原因是脱附激活能等因 素造成种子层具有不同的表面粗糙度，进而使坡莫合金具有不同的微结构和磁性能. 关键词： NiFeNb种子层 坡莫合金 磁滞回线 粗糙度}     

Thickness-dependent magnetic properties of Ni81Fe19, Co90Fe10 and Ni65Fe15Co20 thin films

We present results of magnetization and magnetic anisotropy measurements in thin magnetic films of the alloys Ni₈₁Fe₁₉, Co₉₀Fe₁₀ and Ni₆₅Fe₁₅Co₂₀ that are commonly used in magnetoelectronic devices. The films were sandwiched between layers of Ta. At room temperature the critical thickness for all the films to become ferromagnetic is in the range 11–13 Å. In Co₉₀Fe₁₀ the coercivity and the anisotropy field both depend strongly on layer thickness.     

X-ray photoelectron spectroscopy study of magnetic films

Ta/NiO_x/Ni₈₁Fe₁₉/Ta films were prepared by rf reactive and dc magnetron sputtering. The exchange coupling field H_ex and the coercivity H_c of NiO_x/Ni₈₁Fe₁₉ as a function of the ratio of Ar to O₂ during the deposition process were studied. The composition and the chemical states in the interface region of NiO_x/NiFe were also investigated using X-ray photoelectron spectroscopy (XPS) and the peak decomposition technique. The results show that the ratio of Ar to O₂ has a great effect on the chemical states of nickel in NiO_x films. The exchange coupling field H_ex and the coercivity H_c of Ta/NiO_x/Ni₈₁Fe₁₉/Ta are thus seriously affected. XPS is shown to be a powerful tool for characterizing magnetic films. Received: 18 July 2001 / Accepted: 21 December 2001 / Published online: 3 June 2002 RID="*" ID="*"Corresponding author. Fax: +86-010/6232-7283, E-mail: guanghua_yu@263.net     

Synthesis and magnetic properties of Au-coated amorphous Fe20Ni80 nanoparticles

Gold-coated nanoparticles of Fe₂₀Ni₈₀ (permalloy) have been synthesized by a microemulsion process. The as-prepared samples consist of ∼5 nm diameter particles of amorphous Fe₂₀Ni₈₀ that are likely encapsulated in B₂O₃. One or more Fe₂₀Ni₈₀@B₂O₃ particles are subsequently encapsulated in 8-20 nm gold nanospheres, as determined by TEM and X-ray powder diffraction (XRD) line broadening. The gold shells were found to be under expansive strain. Magnetic data confirm the existence of a superparamagnetic phase with a blocking temperature, T_B, of ∼33 K. The saturation magnetization, M_S, of the as-prepared, Au-coated sample is ∼65 emu g⁻¹ at 5 K and ∼16 emu g⁻¹ at 300 K. The coercivity, H_C, is ∼280 Oe at 5 K.     

Magnetization in permalloy thin films

Thin films of permalloy (Ni₈₀Fe₂₀) were prepared using an Ar+N₂ mixture with magnetron sputtering technique at ambient temperature. The film prepared with only Ar gas shows reflections corresponding to the permalloy phase in X-ray diffraction (XRD) pattern. The addition of nitrogen during sputtering results in broadening of the peaks in XRD pattern, which finally leads to an amorphous phase. The M-H loop for the sample prepared with only Ar gas is matching well with the values obtained for the permalloy. For the samples prepared with increased nitrogen partial pressure the magnetic moment decreased rapidly and the values of coercivity increased. The polarized neutron reflectivity measurements (PNR) were performed in the sample prepared with only Ar gas and with nitrogen partial pressure of 5 and 10%. It was found that the spin-up and spin-down reflectivities show exactly similar reflectivity for the sample prepared with Ar gas alone, while PNR measurements on 5 and 10% sample show splitting in the spin-up and spin-down reflectivity.      

Brillouin light scattering study of the magnetic hysteresis loop in Fe-Ni/Si(100) film with induced magnetic anisotropy

The magnetic hysteresis of Fe₅₇Ni₄₃/Si(100) with magnetic anisotropy induced by an external field has been studied by Brillouin light scattering (BLS). The results are compared with those of the magneto-optic-Kerr-effect (MOKE) measurement and the vibrating sample magnetometer (VSM). The BLS results show that the sample film has strong in-plane anisotropy. The angle between the magnetization and a 4.6 G applied magnetic field H reaches a maximum value of 45° when H lies along the hard axis. The coercivity and magnetic anisotropy field for the film obtained by the BLS are compared with the values obtained by the VSM and MOKE measurement.     

Electron scattering characteristics of polycrystalline metal transition films by in-situ electrical resistance measurements

In-situ electrical resistance measurements were performed to obtain the scattering characteristics of very thin polycrystalline metal transition magnetic alloys grown by ion beam deposition (IBD) on specific underlayers. The experimental curves show size effects at small film thicknesses and important differences between Co₈₅Fe₁₅ and Ni₈₁Fe₁₉ thin layers grown on identical underlayers of Ta70 Å/Ru13 Å. The largest difference was observed in Ni₈₁Fe₁₉ films grown on underlayers of amorphous Ta70 Å. The experimental curves of electrical resistivity/conductivity variation with layer thickness were well fit within the Mayadas and Shatzkes (M-S) model, assuming specific formulations for grain growth with layer thickness.     

Magnetism in very thin films of permalloy measured by spin polarized cascade electrons

The spin polarizationP of the low energy cascade electrons excited with a primary unpolarized electron beam is measured with ultrathin films of permalloy (Ni₈₀Fe₂₀) as a function of film thickness, external magnetic field, and temperatureT. Surface adsorbates of small concentrations of less than 10% of a monolayer can change the Curie point and the saturation value ofP ₀(T0) by as much as 30%. The Ta-substrate induces a magnetically dead region in permalloy. Conventional spin wave theory cannot account for the observed smallT-dependence of the magnetizationM. Films on a nonmagnetic substrate are compared to similar films coupled to bulk permalloy over an interface of Ta. TheT-dependence ofM with the coupled films can be explained by spin wave theory. At lowT, the films coupled to the bulk exhibit a faster decrease ofM than the uncoupled films. We propose that this thermal stabilization of the magnetization in very thin ferromagnetic films is due to quenching of the long wavelength spin modes.     

Structural,magnetic and dielectric properties of (Li1+, Al3+) co-doped Ni0.5Zn0.5Fe2O4 ferrite ceramics prepared by the sol-gel auto-combustion method

(Li¹⁺, Al³⁺) co-doped Ni_0.5Zn_0.5Fe₂O₄ ferrites, Ni_0.5-xZn_0.5-xLi_xAl_xFe₂O₄ (x = 0.000, 0.025, 0.050 and 0.100), were synthesized by the sol-gel auto-combustion method. X-ray diffraction (XRD), field emission scanning electronic microscope (FESEM), vibrating sample magnetometer (VSM) and LCR meter were used to investigate the structural, magnetic and dielectric properties. Results of XRD and SEM indicate that both doping amount and calcination temperature play significant roles in crystal structure and grain growth. Also, it can be observed that the saturation magnetization and the coercivity change in a noticeable manner. The Ni_0.475Zn_0.475Li_0.025Al_0.025Fe₂O₄ ferrite sintered at 1200 °C has a relatively low coercivity value (62.93 Oe) and the largest saturation magnetization (110.95 emu/g). Besides, dielectric behavior is also improved by Li¹⁺ and Al³⁺ co-doping.     

Studies on the valence electronic structure of Fe and Ni in Fe x Ni1−x alloys

K _β-to-K _α X-ray intensity ratios of Fe and Ni in pure metals and in Fe _x Ni_1−x alloys (x=0.20, 0.50, 0.58) exhibiting similar crystalline structure have been measured following excitation by 59.54 keV γ-rays from a ²⁴¹Am point source, to understand as to why the properties of permalloy Fe_0.2Ni_0.8 is distinct from other alloy compositions. It is observed that the valence electronic structure of Fe_0.2Ni_0.8 alloy is totally different from other alloys which may be attributed to its special magnetic properties.     

A study of the properties and microstructure of Ni81Fe19 ultrathin films with MgO

The anisotropic magnetoresistance (AMR) of a Ta (5 nm)/MgO (3 nm)/Ni₈₁Fe₁₉ (10 nm)/MgO (2 nm)/Ta (3 nm) film with MgO-Nano Oxide Layer (NOL) increases dramatically from 1.05% to 3.24% compared with a Ta (5 nm)/Ni₈₁Fe₁₉ (10 nm)/Ta (3 nm) film without the MgO-NOL layer after annealing at 380 °C for 2 h. Although the MgO destroys the NiFe (1 1 1) texture, it enhances the specular electron scattering of the conduction electrons at the NOL interface and suppresses the interface reactions and diffusion at the Ta/NiFe and NiFe/Ta interfaces. The NiFe (1 1 1) texture was formed after the annealing, resulting in a higher AMR ratio. X-ray photoelectron spectroscope results show that Mg and Mg²⁺ were present in the MgO_x films.     

Local anodization of permalloy film by atomic force microscope

Local anodization on a permalloy (_Ni80Fe20)${\mathrm{Ni}}_{80}{\mathrm{Fe}}_{20})$ thin film by an atomic force microscope (AFM) in air was studied. Fabrication of uniform structure on the permalloy film was difficult in comparison with that on a Si(1 0 0) substrate. On the permalloy film, threshold voltage for the AFM anodization increased until 3 h after exposure to air. With passage of time, I–V$I–V$ curves on the permalloy film also changed from metallic behavior to insulating one. In addition, I–V$I–V$ curves varied at positions on the permalloy film. The oxide layer with time- and position-dependencies can induce non-uniform structure in AFM anodization. However, uniformity of structure was able to be improved by using method of fabrication of dots.     

Microstructure and magnetic properties in arrays of ac electrodeposited FexNi1?x nanowires induced by the continuous and pulse electrodeposition

FeNi nanowires were fabricated by ac and pulse electrodeposition into the alumina template matrix. The effects of continuous ac electrodeposition as well as pulse features on the structure and magnetic properties of the nanowire arrays were studied. The microstructures and magnetic properties of the Fe _x Ni_1−x nanowires are seen to be independent of the deposition frequency and off-time between the pulses. The ac electrodeposited Ni nanowires were not formed at more than 400  Hz deposition frequency, while the Fe _x Ni_1−x nanowires, containing a small amount of Fe, formed in the all frequencies. For x less than 50% the coercivity slowly increases but over 50% Fe added to the FeNi alloy increases the coercivity with a higher rate and maximum coercivity was seen for the Fe_0.97Ni_0.03. The Fe and Fe _x Ni_1−x nanowires containing less than 30 at.% Ni was seen to have a bcc structures with (110) preferential direction while Fe _x Ni_1−x nanowires with more than 30 at.% Ni showed (110) bcc (Fe) and/or (111) bcc (FeNi) plus (111) fcc (Ni). A preferential (111) fcc structure was obtained for the Ni nanowires.     

Surface modification of permalloy (Ni<Subscript>80</Subscript>Fe<Subscript>20</Subscript>) nanoparticles for biomedical applications

We report a simple and novel method for surface biofunctionalization onto recently reported Ni₈₀Fe₂₀ permalloy nanoparticles (~71 nm) and the immobilization of a model protein, IgG from human serum. The strategy of protein immobilization involved attachment of histidine-tagged streptavidin to the Ni₈₀Fe₂₀ nanoparticles via a non-covalent ligand binding followed by biotinylated human IgG binding on the nanoparticle surface using the specific high affinity avidin–biotin interaction. The biofunctionalization of Ni₈₀Fe₂₀ permalloy nanoparticles was confirmed by Fourier Transform InfraRed (FTIR) spectroscopy and protein denaturing gel electrophoresis (lithium dodecyl sulfate-polyacrylamide gel electrophoresis, LDS-PAGE). This protocol for surface functionalization of the novel nanometer-sized Ni₈₀Fe₂₀ permalloy particles with biological molecules could open diverse applications in disease diagnostics and drug delivery.     

Ionic liquid gating control of magnetic anisotropy in Ni0.81Fe0.19 thin films

Voltage control magnetism is one of the most energy efficient pathway towards magnetoelectric (ME) device. Ionic liquid gating (ILG) method has already shown impressive manipulation power at the IL/electrode interface to influence the structure, orbital as well as spin of the electrode materials. As key material in anisotropy magnetoresistance sensor and spin valve heterostructure, the permalloy Ni_0.81Fe_0.19 was utilized as the electrode to investigate the ILG induced magnetic anisotropy change. In this work, we realized magnetic anisotropy control in Au/[DEME]⁺[TFSI]^-/Ni_0.81Fe_0.19 (2.5 nm)/Ta heterostructure via ILG caused electrostatic doping. This is evidenced in situ reversible ferromagnetic field (H_r) shift with electron spin resonance (ESR) spectrometer. Aiming at the question whether the charge accumulation at the ionic liquid interface is the main control mechanism at low voltage, we carefully tested the relationship between the change of resonance field and the amount of surface charge. It was found that these two had a good linear relationship between −1 V and +1 V. Defining the linear parameter as A whose value is 28.7 mT m²/Col. Unlike previously reported chemical regulation of Co, this article used ionic liquids to physically regulate NiFe, which has not been studied in the previous ionic liquid regulation. And NiFe has a narrower resonance line width for easy reference to microwave devices. In addition, It also has a stronger ferromagnetic signal than Co, which can be more easily detected as a sensor device. Therefore, this system is more promising. The ILG control NiFe may lead to a new kind of magnetoelectric sensor devices and path a new way to low energy consumption spintronics.     

Time-dependent absorption of gamma-radiation under high-frequency magnetic excitation of 57Fe

Summary We have studied the time dependence of M?ssbauer absorption in a magnetically soft sample of Fe₁₈Ni₈₂ permalloy under the influence of a radio-frequency (r.f.) magnetic field. Absorption was measured as a function of the r.f. field phase at specific gamma-ray energies. We have shown that measuring the time dependence of absorption makes it possible to differentiate between purely magnetic and magnetoacoustic modulation mechanisms even in cases where clear distinction is not visible in conventional energy domain spectra. Paper presented at ICAME-95, Rimini, 10–16 September 1995.     

Soft magnetic properties of NiFe compacted powder alloys

It is known that Ni–Fe based alloys (permalloys) are important soft magnetic materials, which have been widely applied in the field of electronic devices and industry. The most suitable permalloys for application exhibit low value of coercivity and magnetostriction (for about 80 at% Ni), high saturation magnetic induction (for about 50 at% Ni), higher electrical resistivity (for about 35 at% Ni). The aim of this work was to investigate the structure and magnetic properties of _Ni81Fe19${\mathrm{Ni}}_{81}{\mathrm{Fe}}_{19}$ (wt%) compacted powder material in the form of small cylinders.     

Planar Hall effect and magnetoresistance in Ni81Fe19 and Co square shaped thin films

Ni₈₁Fe₁₉ and Co thin films have been fabricated and their transport properties have been investigated for potential applications in ultra sensitive magnetic field sensors. The Ni₈₁Fe₁₉ films exhibit an anisotropic magnetoresistance (AMR) of 2.5% with a coercivity 2.5 Oe and the Co films exhibit an AMR of 0.7% with coercivity 11 Oe. Large planar Hall effect magnetoresistance values at room temperature are reported for both cases. An unbalanced Wheatstone bridge model is proposed to describe quantitatively the observed experimental Planar Hall Effect data.