Dielectric behavior of spin-deposited nanocrystalline nickel-zinc ferrite thin films processed by citrate-route

Nanocrystalline nickel-zinc ferrite thin films with the general formula Ni_1−xZn_xFe₂O₄, where x=0.0, 0.2, 0.4 and 0.6 were fabricated via a chemical route known as the citrate precursor route. These films were spin-deposited on indium-tin oxide coated glass, fused quartz and amorphous Si-wafer substrates, and annealed at various temperatures up to 650 °C. The films annealed below 400 °C were found to be X-ray amorphous, while the films annealed at and above 400 °C were polycrystalline exhibiting a single-phase spinel structure. The average grain size of the films evaluated by transmission electron microscopy, is found to be in the range 4-8.5 nm. The room temperature DC resistivity of the films is in the range 10³-10⁷ Ω m. Dielectric constant and dielectric loss were measured in the frequency range 100 Hz-1 MHz. Dielectric constant of the films is found to lie between 25 and 44, while the loss factor is if the order of 10⁻². The higher values of the dielectric constant for films having higher zinc concentration are attributable to the enhanced hopping between Fe²⁺ and Fe³⁺ ions in these samples. The M-H hysteresis measurement of the nickel ferrite thin films annealed at 650 °C showed narrow hysteresis loop—a characteristic of soft ferromagnetic material.     

Effect of magnesium substitution on dielectric and magnetic properties of Ni-Zn ferrite

The dielectric and magnetic properties of Mg incorporated Ni-Zn spinel ferrites have been investigated. Ni_0.5−xZn_0.5Mg_xFe₂O₄ ferrites have been prepared by sol-gel auto-combustion technique. The as prepared ferrites were annealed at 673, 873 and 1073 K. The X-ray diffraction studies reveal the spinel structure of annealed ferrites. The TEM results are in agreement with XRD results. FTIR study has also been carried out to get insight into the structure of these ferrites. The dielectric measurements show that the dielectric constant (ε′), dielectric loss (tan δ) and conductivity (σ_ac) increase on incorporation of Mg in the Ni-Zn ferrite. ε′, tan δ and σ_ac also show dependence on temperature, frequency of external applied electric field and microstructure of the samples. The magnetic moment measurements reveal that the saturation magnetization (M_s) increases and coercivity (H_c) decreases with the increase in concentration of Mg²⁺ ions. M_s and H_c also show dependence on the annealing temperature.     

Effect of Pr doping on magnetic and dielectric properties of Ni-Zn ferrites by “one-step synthesis”

Pr³⁺-doped Ni-Zn ferrites with a nominal composition of Ni_0.5Zn_0.5Pr_xFe_2−xO₄ (where x=0-0.08) were prepared by a one-step synthesis. The magnetic and dielectric properties of the as-prepared Ni-Zn ferrites were investigated. X-ray diffraction data indicated that, after doping, all samples consisted of the main spinel phase in combination of a small amount of a foreign PrFeO₃ phase. The lattice constants of the ferrites initially increased after Pr³⁺ doping, but then became smaller with additional Pr³⁺ doping. The addition of Pr³⁺ resulted in a reduction of grain size and an increase of density and densification of the as-prepared samples. Magnetic measurement revealed that the saturation magnetization of the as-prepared ferrites, M_s, decreased, while the coercivity, H_c, increased with increasing substitution level, x, and the Curie temperature, T_c, kept a rather high value, fluctuating between 308 and 320 °C. Both the real and imaginary parts of permeability of the ferrites decreased slightly after Pr³⁺ doping. However, the natural resonance frequency shifted towards higher frequency from 13.07 to 36.17 MHz after the addition of Pr³⁺, driving the magnetic permeability to much higher frequency, reaching the highest value (36.17 MHz) when x=0.04. Introduction of Pr³⁺ ions into the Ni-Zn ferrite reduced the values of the dielectric loss tangent, especially in the frequency range of 1-400 MHz. However, the magnitude of dielectric loss of the samples doped with different amounts of Pr³⁺ raised little.     

Effect of zinc concentration on the structural,electrical and magnetic properties of mixed Mn–Zn and Ni–Zn ferrites synthesized by the citrate precursor technique

Mixed manganese-zinc and nickel-zinc ferrites of composition Mn_0.2Ni_0.8−xZn_xFe₂O₄ where x=0.4$x=0.4$, 0.5 and 0.6 have been synthesized by the citrate precursor technique. Decomposition of the precursor at temperatures as low as 500 °C gives the ferrite powder. The ferrites have been investigated for their electrical and magnetic properties such as saturation magnetization, initial permeability, Curie temperature, AC-resistivity and dielectric constant as a function of sintering temperature and zinc content. Structural properties such as lattice parameter, grain size and density are also studied. The mixed compositions exhibited higher saturation magnetizations at sintering temperatures as low as 1200 °C. While the Curie temperature decreased with zinc content, the permeability was found to increase. The AC-resistivity ranged from 10⁵–10⁷ Ω cm and decreased with zinc content and sintering temperature. The dielectric constants were lower than those normally reported for the Mn–Zn ferrites. Samples sintered at 1400 °C densified to about 94% of the theoretical density and the grain size was of the order of about 1.5 μm for the samples sintered at 1200 °C and increased subsequently with sintering temperature.     

Influence of rare earth Ce on structural, electrical and magnetic properties of Sr based W-type hexagonal ferrites

A series of single phase W-type Sr_3−xCe_xFe₁₆O₂₇ (x=0, 0.02, 0.04, 0.06, 0.08, 0.10) hexagonal ferrites prepared by the Sol-Gel method was sintered at 1050 °C for 5 h. The X-ray diffraction analysis reveals that all the samples belong to the family of W-type hexagonal ferrites. The c/a ratio falls in the range of W-type hexagonal ferrites. The grain size was measured by SEM varies from 0.7684 to 0.4366 μm which shows that the Ce³⁺ substituted samples have smaller grain size than pure ferrite Sr₃Fe₁₆O₂₇ which results from the difference in ionic radii of Ce³⁺ (1.034 Å) and Sr²⁺ (1.12 Å). The room temperature resistivity of the present samples varies from 6.5×10⁸ to 272×10⁸ Ω-cm. The coercivity increases from 1370 to 1993 Oe which is consistent with the decrease in grain size. The coercivity values indicate that the present samples fall in the range of hard ferrites. The large value of H_c may be due to domain wall pinning at the grain boundaries.     

Structural,magnetic and electrical properties of Co1−xZnxFe2O4 synthesized by co-precipitation method

Nanoparticles of Co_1−xZn_xFe₂O₄ with stoichiometric proportion (x) varying from 0.0 to 0.6 were prepared by the chemical co-precipitation method. The samples were sintered at 600 °C for 2 h and were characterized by X-ray diffraction (XRD), low field AC magnetic susceptibility, DC electrical resistivity and dielectric constant measurements. From the analysis of XRD patterns, the nanocrystalline ferrite had been obtained at pH=12.5–13 and reaction time of 45 min. The particle size was calculated from the most intense peak (3 1 1) using the Scherrer formula. The size of precipitated particles lies within the range 12–16 nm, obtained at reaction temperature of 70 °C. The Curie temperature was obtained from AC magnetic susceptibility measurements in the range 77–850 K. It is observed that Curie temperature decreases with the increase of Zn concentration. DC electrical resistivity measurements were carried out by two-probe method from 370 to 580 K. Temperature-dependent DC electrical resistivity decreases with increase in temperature ensuring the semiconductor nature of the samples. DC electrical resistivity results are discussed in terms of polaron hopping model. Activation energy calculated from the DC electrical resistivity versus temperature for all the samples ranges from 0.658 to 0.849 eV. The drift mobility increases by increasing temperature due to decrease in DC electrical resisitivity. The dielectric constants are studied as a function of frequency in the range 100 Hz–1 MHz at room temperature. The dielectric constant decreases with increasing frequency for all the samples and follow the Maxwell–Wagner's interfacial polarization.     

Impacts of neodymium on structural,spectral and dielectric properties of LiNi0.5Fe2O4 nanocrystalline ferrites fabricated via micro-emulsion technique

Soft ferrites are technologically advanced smart materials and their properties can be tailored by controlling the chemical composition and judicial choice of the metal elements. In this article we discussed the effect of rare earth neodymium (Nd³⁺) on various properties of LiNi_0.5Nd_xFe_2−xO₄ spinel ferrites. These ferrites have been synthesized by facile micro-emulsion route and characterized by X-ray diffraction (XRD), fourier transform infrared spectroscopy (FTIR), a.c. electrical conductivity and thermal analysis. The influence of Nd³⁺ doping on structural and electrical parameters has been investigated. XRD analysis revealed the formation of single cubic spinel structure for x≤0.07. Few traces of secondary phase (NdFeO₃) were found for x≥0.105. The secondary phase induced owing to the solubility limit of Nd³⁺ cations in these ferrites. The lattice parameter (a) and crystallite size (D) both exhibit non-linear relation. The values of “a” and “D” were found in the range 8.322–8.329 Å and 25–32 nm respectively. These variations were attributed to the larger ionic radius of Nd³⁺ cations as compared to the host cations and lattice strain produced in these ferrites. The dielectric parameters were studied in the range 1 MHz to 3 GHz and these parameters were damped by Nd³⁺ incorporation and also by increasing the frequency. The reduced dielectric parameters observed in wide frequency range proposed that these nanocrystalline ferrites are potential candidates for fabricating the devices which are required to operate at GHz frequencies.     

Magnetic and dielectric studies of nanocrystalline zinc substituted Cu-Mn ferrites

Ferrites with the general formula Cu_1−xZn_xFeMnO₄ (where 0≤x≤1) were prepared through a citrate gel auto-combustion route. Structural characterizations carried out by X-ray diffraction reveal that the lattice constant increases with increase in zinc content. Transmission electron microscopic measurements confirm the nanoscale nature of the particles. Room temperature saturation magnetization was measured as a function of zinc concentration. The saturation magnetization increases up to x=0.25 and then decreases as zinc concentration increases. Dielectric permittivity, dielectric loss tangent, ac conductivity and complex dielectric impedance were studied in the frequency range 20 Hz-1 MHz. The results indicated a usual dielectric dispersion due to the Maxwell-Wagner type of interfacial polarization. Dielectric loss showed similar behavior as dielectric permittivity. The ac conductivity increased linearly with frequency. Complex impedance spectroscopic studies confirmed that conduction in the samples is via grain boundaries. In general, substitution of zinc plays an important role in changing the structural, electrical and magnetic properties of these ferrites.     

Studies on the activation energy from the ac conductivity measurements of rubber ferrite composites containing manganese zinc ferrite

Manganese zinc ferrites (MZF) have resistivities between 0.01 and 10 Ω m. Making composite materials of ferrites with either natural rubber or plastics will modify the electrical properties of ferrites. The moldability and flexibility of these composites find wide use in industrial and other scientific applications. Mixed ferrites belonging to the series Mn_(1−x)Zn_xFe₂O₄ were synthesized for different ‘x’ values in steps of 0.2, and incorporated in natural rubber matrix (RFC). From the dielectric measurements of the ceramic manganese zinc ferrite and rubber ferrite composites, ac conductivity and activation energy were evaluated. A program was developed with the aid of the LabVIEW package to automate the measurements. The ac conductivity of RFC was then correlated with that of the magnetic filler and matrix by a mixture equation which helps to tailor properties of these composites.     

Complex permittivity and complex permeability of Sr ions substituted Ba ferrite at X-band

M-type hexagonal ferrite composition, Ba_(1−x)Sr_xFe₁₂O₁₉ (x=0.0, 0.2, 0.4, 0.6, 0.8 and 1.0), was prepared by a two route ceramic method. Complex permittivity (ε′−jε″) and complex permeability (μ′−jμ″) have been measured using a network analyzer from 8.2 to 12.4 GHz X-ray diffraction confirmed the M-type hexagonal structure and a scanned electron micrograph was used to analyze the grain size distribution of ferrite. Substitution of Sr²⁺ ions causes an increase in porosity that deteriorates the electromagnetic and microstructural properties in the doped samples. Both dielectric constant and dielectric loss are enhanced in comparison to the permeability and magnetic loss over the entire frequency region. This is due to a resistivity variation and the formation of Fe²⁺ ions, which increases the hopping mechanism between Fe²⁺ and Fe³⁺ ions.     

Electromagnetic properties of lithium zinc ferrites doped with aluminum

We present the results of the effect of Al substitution on the magnetic and electrical properties of Li_0.2Zn_0.6Fe_2.2−xAl_xO₄ ferrites (0.0≤x≤0.5) prepared by the standard ceramic technique. The characterization has been performed using XRD, SEM, magnetic and dielectric response in frequency. XRD analysis confirms that the system exhibits polycrystalline single phase cubic spinel structure only for low dopant content. Doping decreases the dielectric loss tangent and the ferrite conductivity in more than two orders of magnitude in the whole analyzed frequency range. Attenuation has a maximum intensity (86 dB) near 90 MHz for x=0.4. The wider bandwidth at 20 dB (94.6 MHz) is for x=0.3.     

Structural and electrical properties of nanometric Ni-Cu ferrites synthesized by citrate precursor method

Nanometric nickel copper ferrites Ni_1−xCu_xFe₂O₄, 0≤x≤0.45 were prepared by the citrate precursor method. X-ray diffraction measurements confirm the formation of single phase cubic spinel structure. The lattice parameter (a) is increased with increasing Cu²⁺ ion substitution. The crystallite size was calculated from XRD data and compared with that obtained from TEM micrographs. A significant increase in the density is observed with increasing Cu content. The IR absorption spectra were used for the detection and confirmation of the chemical bonds in spinel ferrites. The dielectric constant ε′ and dielectric loss showed a decrease with increasing frequency for all samples. The decrease in the ac conductivity was ascribed to the increase in hopping length.     

Magnetic properties and DC electrical resistivity studies on cadmium substituted nickel-zinc ferrite system

Polycrystalline Ni_0.65−xCd_xZn_0.35Fe₂O₄ ferrites with x varying from 0.00 to 0.20 in steps of 0.04 have been prepared by conventional ceramic route. Calcination and sintering of samples were performed at 950 and 1250 °C for 4 and 2 h, respectively. The prepared samples were characterized by powder X-ray diffraction. The observed modifications in structure and increase in lattice constant are attributed to the difference in ionic radius of substituted Cd²⁺ ion and displaced Ni²⁺ ion. The room temperature specific saturation magnetization and Curie temperature are observed to decrease continuously with decrease in cadmium content and are attributed to the decline of A-B exchange interaction. The monotonic increase in initial permeability and decrease in magnetic loss are observed with cadmium concentration. An increase in dc electrical resistivity is observed up to x=0.12 of cadmium followed by a continuous decrease. The variation of electrical resistivity with temperature was measured in the temperature range of RT-140 °C and the corresponding activation energies for conduction obtained from the log ρ vs 1/T graphs.     

Electrical and switching properties of NiAlxFe2−xO4 ferrites synthesized by chemical method

Nickel-aluminum ferrite system NiAl_xFe_2−xO₄ has been synthesized by wet chemical co-precipitation method. The samples were studied by means of X-ray diffraction, d.c. electrical resistivity, a.c. electrical resistivity, a.c. conductivity and switching properties. The XRD patterns confirm the cubic spinel structure for all the synthesized samples. The crystallite size calculated from XRD data which confirm the nano-size dimension of the prepared samples. Electrical properties such as a.c. and d.c. resistivities as function of temperature were studied for various Al substitution in nickel ferrite. The dielectric constant and dielectric loss tangent were also studied as a function of frequency. The dielectric constant follows the Maxwell-Wagner interfacial polarization. A.C. conductivity increases with increase in applied frequency. The d.c. resistivity decreases as temperature increases, which indicate that the sample have semi-conducting nature. Verwey hoping mechanism explains the observed variation in resistivity. The activation energy is derived from the temperature variation of resistivity. Electrical switching properties were studied as I-V measurements. The current controlled negative resistance type switching is observed in all the samples. The Al substitution in nickel ferrite decreases the required switching field.     

Magnetic, dielectric and complex impedance spectroscopic studies of nanocrystalline Cr substituted Li-ferrite

Nanocrystalline Li_0.5Fe_2.5−xCr_xO₄ (2.5≤x≥0) ferrites were prepared by a sol-gel autocombustion route. X-ray diffraction was employed to confirm the cubic spinel phase formation of the ferrites. The lattice parameter decreases with increase in Cr content. The saturation magnetization, coercivity and remanance were studied as a function of Cr content. The dielectric constant and dielectric loss were measured as a function of frequency in the frequency range 20 Hz-1 MHz. Frequency dependence of dielectric constant shows dielectric dispersion due to the Maxwell-Wagner type of interfacial polarization. In order to understand the conduction mechanism, complex impedance measurements were carried out. The substitution of chromium plays an important role in changing the dielectric and magnetic properties of lithium ferrites.     

Physical, electrical and dielectric properties of Ca-substituted strontium hexaferrite (SrFe12O19) nanoparticles synthesized by co-precipitation method

Calcium substituted strontium hexaferrite Ca_xSr_1−xFe₁₂O₁₉ (x=0.0−0.6) nanoparticles are synthesized by chemical co-precipitation method. The synthesized samples are characterized by Fourier Transform Infrared (FTIR), X-ray diffraction (XRD), Scanning Electron Microscopy, Transmission Electron Microscopy, DC electrical resistivity and dielectric measurements. FTIR data of uncalcined sample shows that nitrate ions are present which disappeared on calcination at 920 °C. The XRD data shows that a single hexagonal magnetoplumbite phase is formed in samples in which the calcium content, x, is ≤0.20. However, a nonmagnetic phase (α-Fe₂O₃) in addition to the hexagonal phase is also present in samples with x>0.20. The average crystallite size is found between 17 and 29 nm. The DC electrical resistivity increases with increase of calcium content up to level of x=0.2 but decreased on further addition of calcium. The enhanced resistivity of the calcium doped material has potential applications in microwave devices. The variations of dielectric constant and dielectric loss angle are explained on the basis of Maxwell-Wagner and Koops models.     

Structural, electrical and magnetic characterizations of Ni-Cu-Zn ferrite synthesized by citrate precursor method

Fine powders of NiCuZn ferrite with composition Ni_(0.7−x)Cu_xZn_0.3Fe₂O₄ (where x=0, 0.2, 0.4 and 0.6) were prepared by the citrate precursor method. X-ray diffraction measurements confirm the formation of single-phase cubic spinel structure. The grain size was estimated by SEM micrograph which increases with Cu content. Dielectric constant (?) and loss tangent (tan δ) were measured as a function of frequency. The ? and tan δ show a decreasing trend with increase of frequency for all the samples. The DC resistivity was measured as a function of temperature. The temperature-dependent DC resistivity measurements show that the room-temperature DC resistivity of NiCuZn ferrite with x=0.2 is of the order of 10⁹ Ω cm. The AC conductivity (σ_AC) was studied as a function of frequency. The hysteresis data indicate that the maximum saturation magnetization of 38.66 emu/g is obtained for the composition with x=0.2.     

Electrical properties of neodymium doped CaBi4Ti4O15 ceramics

Neodymium doped bismuth layer structure ferroelectrics (BLSFs) ceramics CaBi_4−xNd_xTi₄O₁₅ (x=0, 0.25, 0.50, 0.75) were prepared by solid-state reaction method. X-ray diffraction pattern showed that single phase was formed when x=0-0.75. The refined lattice parameters showed that a (b) axes decrease at x=0.25 and increase with more Nd³⁺ dopant. The effects of Nd³⁺ doping on the dielectric and ferroelectric properties of CaBi₄Ti₄O₁₅ ceramics are studied. Nd³⁺ dopant decreased the Curie temperature linearly, and the dielectric loss, tan δ, as well. The remnant polarization of Nd³⁺ doped CaBi₄Ti₄O₁₅ ceramics was increased by 80% at x=0.25, while more Nd³⁺ dopant decreased the remnant polarization. CaBi_3.75Nd_0.25Ti₄O₁₅ ceramics had the largest piezoelectric constant d₃₃. The structure and properties of CaBi_4−xNd_xTi₄O₁₅ ceramics showed that Nd³⁺ may occupy different crystal locations when Nd³⁺ content x is less than 0.25 and more than 0.50.     

Doping effect of Y ions on the microstructural and electromagnetic properties of Mn-Zn ferrites

Mn-Zn ferrites doped with different contents of Y³⁺ ions were prepared by conventional two-step synthesis method. The microstructure and electromagnetic properties of the as-prepared Mn-Zn ferrites were investigated. It was found that all the samples consisted of ferrite phases of typical spinel cubic structure, and when Y³⁺ ion content was upto 1.5 mol%, yttriumirongarnet (Y₃Fe₅O₁₂) phase with garnet structure was detected. With increasing doping content of Y³⁺ ions, the lattice constant and grain size increased, and after an increase to its maximum value, the sample apparent and relative densities dropped down. Through the analysis of magnetic properties, it was revealed that the saturation magnetization, and both the real and imaginary parts of permeability of the as-prepared samples raised with increasing doping content of Y³⁺ ions but decreased with more Y³⁺ ions, while their coercivity showed an opposite change trend; and the Curie temperature increased monotonously. The measurement of dielectric properties indicated that the dielectric constant of the doped Mn-Zn ferrites presented a rise with increasing Y³⁺ ion content, and dropped down gradually when more Y³⁺ ions were doped, while the dielectric loss tangent would decrease with Y³⁺ content upto 1.5 mol%, but after that, it increased.     

Effect of Y2O3 doping on the electrical transport properties of Sr2MnNiFe12O22 Y-type hexaferrite

Y₂O₃ doped Y-type composite hexa-ferrites Sr₂MnNiFe₁₂O₂₂ + xY₂O₃ (x = 0 wt%, 1 wt%, 2 wt%, 3 wt%, 4 wt%, 5 wt%) were synthesized successfully using sol-gel auto combustion technique. X-ray diffraction analysis reveals Y-type hexagonal structure with few traces of secondary phases. The decrease in grain size as a function of Yttrium content is attributed to the fact that Yttrium acts as a grain inhibitor. The DC resistivity was observed to increase with increasing Yttrium-contents due to the unavailability of Fe³⁺ ions at octahedral sites. Activation energy showed that the samples with high resistivity have high value of activation energy and vice versa. Permittivity decreases with the increase of frequency following Maxwell Wagner Model. In addition, the doped samples exhibit very low dielectric constant and low loss tangent in frequency range 20 Hz–1 MHz. The sample x = 5 wt% exhibit the lowest value of dielectric constant. The variation in imaginary part of dielectric constant and loss tangent with frequency show normal dielectric behavior for all the samples. The frequency dependent ac conductivity increases with increase in frequency and decrease with Y₂O₃ doping. These characteristics may be suitable for their potential applications in electromagnetic attenuation materials and microwave devices. The conductivity mechanism so determined was hopping mechanism. The dc resistivity of the doped ferrites measured in our case is about 10¹⁰ Ω-cm that meets the requirement for fabrication of components by electroplating.