有限元分析法在SOI基微环谐振器设计中的应用

利用有限元法(FEM)分析了大横截面SOI(Silicon-on-insulator)脊型波导的本征模式分布,确定了脊型波导的单模条件。在保证单模传输的情况下,模拟了SOI微环谐振器中波导耦合器的耦合长度、功率耦合系数与波导尺寸和间距的关系。模拟结果表明:对于W=1μm,H=2μm的SOI脊型波导耦合器,耦合长度LC随波导间距d的增加而增大,功率耦合系数随之减小。在波导间距d0.8μm的情况下,耦合长度LC随着归一化脊高r的增加而增大,当d0.8μm时,耦合长度LC随r的增加而减小。模拟结果为SOI微环谐振器的设计和应用提供了理论依据。     

SOI及GeSi/Si脊形光波导的模式与波导几何结构

用有效折射率方法对SOI（绝缘体上硅）及GeSi/Si脊形光波导的单模条件进行了模拟,与Soref的单模条件进行了比较,将两者与实验结果进行了比较,得到了与实验结果符合得非常好的单模条件。同时对多模波导进行了模拟,得到了波导承载一阶和二阶模的条件。     

硅基二氧化硅波导和SOI脊型波导应力双折射研究

采用有限元方法分析了硅基二氧化硅波导和SOI（Silicon on Insulator）脊型波导内部残留热应力引起的双折射.对于硅基二氧化硅波导,应力双折射系数的数量级为10－4,对于上包层为空气的SOI脊型波导,该系数的数量级为10－5,对于上包层为SiO2的SOI脊型波导,该系数的数量级为10－3,可见在硅基二氧化硅波导和上包层为SiO2的SOI脊型波导中产生了大的应力双折射,而在上包层为空气的SOI脊型波导中应力双折射较小.     

基于Optiwave的脊形SiGe OI光波导结构设计

利用有效折射率的数值解法,计算出了SiGe OI脊形光波导的有效折射率.通过对SiGe OI光波导结构参量的理论分析和计算,得到了SiGe OI脊形光波导传输单模光波时内外脊高H,h及脊宽W的尺寸.通过Optiwave软件对SiGe OI脊形光波导进行建模仿真,验证了理论分析和计算的正确性.     

有机聚合物非对称脊波导单模条件分析

以有机聚合物非对称脊波导为研究对象,采用半矢量有限差分光束传输法(FD-BPM),系统地分析了不同脊高、脊宽和芯层平板短侧宽度条件下非对称脊形波导的基模截止和单模条件。得出:在芯层高度一定的情况下,基模截止区域和单模区域均随脊高或脊宽的缩小而增大,单模区域随脊形波导芯层平板短侧宽度s的减小而减小;其尺寸以选择芯层厚度h≥1.5μm,脊高(H-h)≤0.4μm,脊宽4μm≤w≤8μm,芯层平板短侧宽度s=2μm较佳。研究表明,非对称脊波导单模条件区域仍能满足实际应用要求。     

聚合物脊形光波导的变分有效折射率法分析

聚合物脊形光波导是聚合物集成光电子器件的重要构成单元.利用有效折射率法计算聚合物脊形光波导的横向折射率分布及有效折射率,将各区域中的光场分布近似用分段函数表达.基于导模满足的标量波动方程,利用变分法确定变分参量,以求得准确的横向光场分布.对聚合物脊形多模光波导基模和高阶模的色散特性与横向场分布进行分析,研究了波导结构参数对色散特性的影响,计算出TM基模和高阶模的光场分布,得出了聚合物脊形光波导的单模传输条件.研究表明,该方法计算量小、精度高,对聚合物光电子器件中脊形光波导的理论分析与设计优化提供了简单高效的方法.     

硅衬底上锗硅合金光波导设计及工艺的优化考虑

报道用射频加热化学气相沉积法制备Ｓｉ／ＧｅＳｉ／Ｓｉ大断面单模脊形光波导中设计和工艺的进一步完善，ＧｅＳｉ合金层中Ｇｅ的含量Ｘ要满足脊形光波导是单模，光波导的数值，孔径接近单模光纤值，脊高小于临界厚度值等，计算表明兼顾上述三项要求应取ｘ＝１～３％，脊的高与宽受大断面及单模的制约。Ｓｉ的晶体结构使脊的二个腐蚀侧壁是斜坡，为此起始脊宽取５～６μｍ为宜；腐蚀液，抛光液的选取人保证脊则壁及波导面端的优良镜     

基于PML边界的有限差分法及其在光波导泄漏损耗计算中的应用

利用结合完美匹配层(PML)边界的有限差分法计算了光波导的泄漏损耗.通过采用非均匀格点差分格式和反正切坐标变换的方法,有效地减小了计算量并提高了计算精度.分析了PI(polyimide)掩埋型波导和SOI(silicon-on-insulator)脊型波导两种典型结构的泄漏损耗,给出了波导结构尺寸对泄漏损耗的影响,并对有效减小泄漏损耗的方法进行了讨论.     

锥形脊结构半导体光放大器的有限元分析

为提高半导体光放大器与单模光纤耦合效率，建立了半导体放大器的锥形脊结构模型。在该模型下利用有限元数值模拟方法分析，计算了波导区折射率、锥尖宽度、条形波导尺寸、渐变折射率波导层对锥形脊结构模式扩展的影响。通过完善锥形脊结构参量的设计，获得了锥形脊结构半导体光放大器与单模光纤95％的耦合效率。     

硅基脊型波导器件过渡区损耗及偏振效应

在绝缘层上的硅材料上制作了四种具有不同输入输出结构的星形耦合器并进行了测试,对脊形波导与平板波导相互过渡时过渡区的损耗问题进行了研究和讨论,计算得到在所使用的材料参量下利用锥形结构可以得到1dB左右的最小损耗,这一损耗是由于脊型波导与平板波导间的模式失配造成的。以文献中的实验数据为出发点,分析了脊形波导的偏振问题,并通过对脊型波导器件层厚度、脊高、脊宽进行优化设计,得到了不同偏振模式的有效折射率差仅为10^-5量级的单模脊型波导结构,这样的偏振效应在器件设计中可以忽略。     

An analytical and experimental study of the vibration response of a clamped ribbed plate

An analytical solution is presented in this paper for the vibration response of a ribbed plate clamped on all its boundary edges by employing a traveling wave solution. A clamped ribbed plate test rig is also assembled in this study for the experimental investigation of the ribbed plate response and to provide verification results to the analytical solution. The dynamic characteristics and mode shapes of the ribbed plate are measured and compared to those obtained from the analytical solution and from finite element analysis (FEA). General good agreements are found between the results. Discrepancies between the computational and experimental results at low and high frequencies are also discussed. Explanations are offered in the study to disclose the mechanism causing the discrepancies. The dependency of the dynamic response of the ribbed plate on the distance between the excitation force and the rib is also investigated experimentally. It confirms the findings disclosed in a previous analytical study [T.R. Lin, J. Pan, A closed form solution for the dynamic response of finite ribbed plates, Journal of the Acoustical Society of America 119 (2006) 917–925] that the vibration response of a clamped ribbed plate due to a point force excitation is controlled by the plate stiffness when the source is more than a quarter plate bending wavelength away from the rib and from the plate boundary. The response is largely affected by the rib stiffness when the source location is less than a quarter bending wavelength away from the rib.     

Determination of electrical parameters of ZnO/Si heterojunction device fabricated by RF magnetron sputtering

Optical and Quantum Electronics - A single mode condition for silica–titania rib waveguides is proposed in this work. It is applicable to rib waveguides having rib height sufficiently small...     

Acoustic and vibration fields generated by ribs on a fluid-loaded panel,I: Plane-wave problems for a single rib

This paper presents an analytical study of the interaction between incident wave fields, and a single rib on a fluid-loaded panel. The panel is modelled as an infinite membrane (with frequency dependent tension to partially simulate the dispersion characteristics of a thin elastic plate), and the incident waves are taken as plane structural or acoustic waves at normal and oblique incidence on the rib. Our principal concern is with the structural wave field transmitted across the rib (in the case of infinite mechanical impedance and finite non-local rib impedance) through the non-specular acoustic field scattered by the panel-plus-rib is also examined. Matched asymptotic expansions are used to construct analytical approximations covering the entire frequency range, advantage being taken of the smallness of a “fluid-loading-at-coincidence” parameter. The analytical results recover numerical results obtained elsewhere in appropriate regions of parameter space, complement them by providing simple approximations in those regions (typically of rapid variation or of heavy fluid loading) where numerical methods are difficult to implement, and reveal the physical aspects of fluid loading in effecting energy transfer across ribbed structures.     

金属覆盖介质波导在截止点附近的光学特性

本文提出一种适合于截止点附近计算含金属覆盖层介质波层的近似解析方法，详细；地讨论在截止点附近的光波导的模式传播特性 和光电调制特性，并结合有效折射率方法讨论了止型脊形波导调制器的截止条件。     

振幅型复合计算全息模式波前传感理论及验证

全息模式波前传感器是利用复合全息元件对待测波前中像差模式进行直接测量的一种新型波前传感器,其中的复合全息元件可编码设计多阶Zernike像差模式。提出一种有效方案以编码设计振幅型复合计算全息元件,该方案通过将多个编码有某阶Zernike像差模式的透过率调制扭曲光栅叠加产生振幅型计算全息元件。在小像差近似条件下推导了传感器输出信号与Zernike像差模式系数的解析关系。编码设计了振幅型复合全息图,并研究了其对单阶和多阶Zernike像差模式的探测性能。利用液晶光阀加载复合全息图进行了验证实验。所得实验结果与数值模拟结果基本一致。     

Mode-field half widths of Gaussian approximation for fundamental mode of two kinds of optical waveguides

This paper analyzes the characteristic of matching effciency between the fundamental mode of two kinds of optical waveguides and its Gaussian approximate field.Then, it presents a new method where the mode-field half-width of Gaussian approximation for the fundamental mode should be defined according to the maximal matching effciency method. The relationship between the mode-field half-width of the Gaussian approximate field obtained from the maximal matching effciency and normalized frequency is studied; furthermore, two formulas of mode-field half-widths as a function of normalized frequency are proposed.     

Beam Parameters for End Diffraction of TE0 Mode of Planar Waveguide

The relation between diffractive beam parameters and normalized frequency is analyzed that leads to two improved Tormulas for two kinds of mode-field halT-widths and several formulas for divergence angle as well as beam propagation factor. The numerical calculation indicates that the maximal relative error is less than 0.5% within a reasonable parameter range.     

Modal analysis of rib waveguide through finite element and mode matching methods

Two mode solvers based on the finite element and the mode matching methods are compared by way of analyzing rib waveguides. Differences between the normalized propagation constants provided by the two methods are always less than 10^–4 which is at least about one order of magnitude smaller than previously reported values. Results for lossy waveguides and field comparison are also presented.