邻苯三酚红修饰碳糊电极吸附伏安法测定痕量铜

报道了采用邻苯三酚红修饰碳糊电极测定痕量铜的方法。通过在邻苯二甲酸氢钾 -氢氧化钠 (p H4.5)介质中富集 ,Cu2 +和邻苯三酚红形成络合物富集于电极表面 ,然后转换到 0 .0 50 mol· L-1的 H3PO4 中 ,经阴极还原后再进行阳极溶出伏安法测定。Cu2 +浓度在 1 .6× 1 0 -9～ 2 .8× 1 0 -7mol·L-1范围内与二次导数峰电流呈线性关系 ,检出限达 8× 1 0 -10 mol·L-1。同时 ,对电极反应机理进行了探讨。应用于合金样的测定 ,取得满意的结果。     

溴邻苯三酚红修饰碳糊电极吸附伏安法测定痕量锑

研制了溴邻苯三酚红(BPR)作修饰剂的碳糊修饰电极,并采用所制备的电极做工作电极建立了测定锑的方法。测定了电活性络合物的组成,并探讨了电极反应机理。该方法已用于锌电解液中痕量锑的测定,结果满意,检出限为2.0×10-8 mol/L。     

茜素修饰碳糊电极吸附伏安法测定痕量铜

报道了采用茜素修饰碳糊电极测定痕量铜的阳极溶出伏安法。在浓度为0 .1 mol/L 的 HAc- Na Ac缓冲溶液 (p H4.5)中 ,于 +0 .1 0 V处富集 ,- 0 .30 V还原后再进行阳极化扫描 ,于 - 0 .0 5V处获得一灵敏的铜的溶出峰 ,二次导数峰电流与铜浓度在 1 .6× 1 0 -9mol/L～ 4.7× 1 0 -7mol/L范围内呈线性关系 ,检出限达 8.0× 1 0 -10 mol/L。同时 ,对电极反应机理进行了讨论。方法应用于锌合金中铜的测定。     

邻苯三酚红修饰碳糊电极阳极溶出伏安法测定痕量锡的研究

研制了邻苯三酚红(PR)修饰碳糊电极,研究了采用该电极测定痕量锡的阳极溶出伏安法.在0.15 mol/L乙酸盐缓冲溶液(pH 4.5)中,通过开路富集,Sn(Ⅳ)与修饰电极表面的邻苯三酚红生成络合物而富集于电极表面,然后介质交换至4.0mol/L盐酸中,于-0.80 V还原后再进行阳极化扫描,于-0.69 V左右获得一灵敏的Sn的溶出峰,二次导数峰电流与Sn(Ⅳ)浓度在1.68×10-8～1.68×10-6mol/L范围内呈现良好的线性关系,检出限达8×10-9mol/L.对电极反应机理进行了讨论,方法已应用于罐头食品中锡的测定.     

茜素紫修饰碳糊电极阳极溶出伏安法测定痕量锡

研究了利用茜素紫修饰碳糊电极测定痕量锡的阳极溶出伏安法。在 0 1 5mol/L醋酸盐缓冲溶液 (pH 4 .8)中 ,通过开路富集 ,Sn 和茜素紫形成络合物富集于电极表面 ,然后经过介质交换至 3 0mol/L的盐酸溶液中 ,于 -0 .80V还原后再进行阳极化扫描 ,于 -0 .68V左右获得一灵敏的锡的溶出峰。二次导数峰电流与Sn 浓度在 8.4× 1 0 -9～ 1 .4× 1 0 -6mol/L范围内呈良好的线性关系。检出限达 4×1 0 -9mol/L ,同时对电极反应机理进行了讨论。     

茜素紫修饰碳糊电极吸附阳极溶出伏安法测定痕量锑的研究

报道了采用茜素紫修饰碳糊电极测定痕量锑的阳极溶出伏安法。在 0 .0 3mol·L- 1邻苯二甲酸氢钾 盐酸缓冲溶液 (pH 2 .4 )中 ,通过开路富集 ,Sb(Ⅲ )与茜素紫形成络合物而富集于电极表面 ,然后交换介质至 0 .6mol·L- 1盐酸中 ,于 - 0 .6 0V还原后再进行阳极化扫描 ,于 - 0 .50V左右获得一灵敏的锑的溶出峰 ,二次导数峰电流与Sb(Ⅲ )的浓度在 4 .1× 10 - 9～ 2 .9× 10 - 7mol·L- 1范围内呈线性关系 ,检出限达 1.6× 10 - 9mol·L- 1。方法应用于水样中锑的测定 ,结果满意     

甲壳素修饰碳糊电极测定痕量铜

报道了采用甲壳素修饰碳糊电极测定痕量铜的方法。通过开路富集，Ｃｕ６２＋和甲壳素形成络合物富集于电极表面，然后经介质交换，电位还原再进行阳熔出伏安测定。在浓度为３．０×１０＾－９－９．０×１２０＾－７ｍｏｌ／Ｌ范围内，峰电流与痕量铜浓度呈线性关系，检测限为１．０×１０＾－９ｍｏｌ／Ｌ。同时，对电极反应的机理进行了讨论。     

修饰铋盘电极吸附伏安法测定痕量钴的研究

研究了利用丁二酮肟修饰铋电极测定钴的吸附伏安分析方法。在0.4 mol/L NH3.H2O-NH4Cl缓冲溶液(pH=9.0)中,Co(Ⅱ)与铋盘电极表面修饰的丁二酮肟形成螯合物。并于-1.20 V附近产生一个灵敏的还原峰。富集时间分别为60 s和280 s时,峰电流与钴的质量浓度在0.01~25μg/mL和0.002~2μg/mL范围内呈线性关系。该还原峰与采用汞电极时的峰形相似、电位相近、灵敏度相当。优化了实验条件,拟订了样品分析的步骤,利用该法测定了合金、维生素B12针剂样品中的微量钴。     

丁二酮肟修饰碳糊电极阳极溶出伏安法测定痕量铋

报道了用丁二酮肟修饰碳糊电极测定微量铋的电分析方法。Bi~(3+)通过与电极表面的丁二酮肟作用而富集在电极表面,同时在-0.40 V(vs.SCE)还原成零价,当电极电势从-0.40 V向0.40 V扫描时,被还原的铋从电极表面溶出,在0.03 V出现一个十分灵敏的阳极溶出峰。优化了各种实验参数,如支持电解质的选择及pH值、丁二酮肟的用量、富集电位及时间等。修饰电极测定铋的线性范围为1×10~(-9)～1×10~(-6)mol/L。富集6 min后检出限可达4×10~(-10)mol/L。该方法简便快速,灵敏度高,分析成本低廉,并成功应用于实际水样中微量铋的测定。     

碳糊修饰电极吸附伏安法测定食品中的锑

研制了溴邻苯三酚红 (BPR)作修饰剂的碳糊修饰电极 ,并用此电极作工作电极建立了测定痕量锑的吸附伏安法。在选定的实验条件下 ,峰电流与Sb(Ⅲ )浓度在 8.0× 1 0 -9～ 2 .0× 1 0 -7mol L范围内呈线性关系 ,检出限为 2 .0×1 0 -9mol L ,1 0次测定相对标准偏差为 2 .0 % ,不用分离 ,可直接测定食品中痕量Sb(Ⅲ ) ,测定的回收率为 90 %～ 1 0 3%。     

槲皮素化学修饰碳糊电极吸附溶出伏安法测定痕量铅

建立了用槲皮素修饰碳糊电极测定痕量铅的新方法 ,在 0 .1 0mol L甲酸盐缓冲液 (pH 4.3 )中 ,于 -0 .1 0V(vs.SCE)搅拌富集 ,再在 -0 .70V静止还原 40s后 ,阳极化扫描 ,于 -0 .42V左右获得一灵敏的铅阳极溶出峰。在最佳条件下 ,富集不同时间 ,其二次导数峰电流与Pb2 + 在 1 .0× 1 0 - 8～ 8.0× 1 0 - 7mol L和 2 .0× 1 0 - 9～ 6.0× 1 0 - 8mol L两个范围内呈线性关系 ,检出限为 8.0× 1 0 - 1 0 mol L(S N =3 )。同时初步探讨了电极反应机理。     

Catalytic Adsorptive Stripping Voltammetry at a Carbon Paste Electrode for the Determination of Amiodarone

Voltammetry using solid electrodes usually suffers from the contamination due to the deposition of the redox products of analytes on the electrode surface. The contamination has resulted in poor reproducibility and overelaborate operation procedures. The use of the chemical catalysis of oxidant on the reduction product of analyte not only can eliminate the contamination of analyte to solid electrodes but also can improve the faradaic response of analyte. This work introduced both the catalysis of oxidant K2S2O8 and the enhancement of surfactant Triton X-100 on the faraday response of amiodarone into an adsorptive stripping voltammetry at a carbon paste electrode for the determination of amiodarone. The method exhibits high sensitivity, good reproducibility and simple operation procedure. In 0.2 mol·L^-1 HOAc-NaOAc buffer （pH=5.3） containing 2.2×10^-2 mol·L^-1 K2S2O8 and 0.002% Triton X-100, the 2.5th-order derivative stripping peak current of the catalytic wave at 0.3 V （vs. Ag/AgCl） is rectilinear to amiodarone concentration in the range of 2.0×10^-10-2.3×10^-8 mol·L^-1 with a detection limit of 1.5×10^-10 mol·L^-1 after accumulation at 0 V for 30 s.     

Determination of Trace Vanadium by Adsorptive Stripping Voltammetry at a Carbon Paste Electrode

A method for the voltammetric determination of vanadium using a carbon paste electrode (CPE) was described. The new procedure is based on the adsorptive accumulation of the V(V)‐alizarin red S(ARS) complex onto the surface of the CPE, followed by the electrochemical reduction of adsorbed species. The optimal experimental conditions include the use of 0.10 mol/L acetate buffer (pH 5.1), 1.0×10^?5 mol/L ARS, an accumulation potential of ?0.10 V (versus SCE), an accumulation time of 2 min, a scan rate of 200 mV/s and a second‐order derivative linear scan mode. The reduction peak for the complex appears at ?0.52 V. The peak current is proportional to the concentration of V(V) over the range of 0.10–15.0 μg/L, and the detection limit is 0.04 μg/L for a 2 min adsorption time. The relative standard deviations(n=8) for 2.0 and 0.50 μg/L V(V) are 3.1 and 4.7%, respectively. The proposed method was applied to the determination of vanadium in water samples.     

Adsorptive Stripping Voltammetric Determination of 2,4-Dichlorophenol by Laponite Modified Carbon Paste Electrode

A laponite modified carbon paste electrode was prepared, characterized and applied for the 2,4-dichlorophenol (2,4-DCP) voltammetric determination. It takes advantage of the ability of laponite to adsorb phenols, as well as of its availability and very low cost. Kinetic and equilibrium data for 2,4-DCP adsorption by laponite in aqueous dispersions demonstrated that the adsorption process obeyed a pseudo first order kinetic model and was consistent with the formation of adsorbed multilayers on a surface with heterogeneous pore distribution. The composite paste electrode exhibited a heterogeneous surface with 65 % increased surface area and 27 % enhanced catalytic activity compared to the unmodified one. The adsorptive stripping voltammetric determination of 2,4-DCP at an electrode with an optimized graphite:laponite ratio of 55 : 15 w% using a 3 min accumulation time at pH 5.5 was found to be suitable for its quantification in the linear concentration range extended up to 50 μmol L⁻¹ with a sensitivity of 0.56 μA L μmol⁻¹ and a LOD of 0.2 μmol L⁻¹ (S/N=3).The 2,4-DCP electrochemical response was not affected by the presence of some structurally similar phenols, like catechol and p-nitrophenol, while resorcinol, 2-chlorophenol, and 4-chlorophenol presented interferences. The results were validated by 2,4-DCP determination in spiked tap water.     

碳糊电极吸附溶出伏安法测定游离钙

基于Ca(Ⅱ)-茜素红S(ARS)络合物在碳糊电极上的还原波,建立了吸附溶出伏安测定游离钙的新方法。在1.5×10-2mol/LKOH-2.0×10-5mol/LARS介质中,Ca(Ⅱ)-ARS络合物在碳糊电极上于-0.89V处产生一吸附还原波。当富集电位为.0.1V,富集时间90s,扫描速度为100mV/s时,该络合物单扫描阴极溶出峰的二阶导数峰电流与游离钙离子浓度在3.0×10-8~2.0×10-6mol/L范围内呈线性关系;检出限为9.4×10-9mol/L。在0.2mol/LHCl中清洗2min,该电极重现性良好。该方法可用于血清、牛奶和自来水中游离钙的测定。     

秋水仙碱在碳糊电极上的吸附伏安行为

秋水仙碱在硫酸溶液中加热水解得分析试液。在０．０５ｍｏｌ／ＬＨ２ＳＯ４底液中，用碳糊电极吸附伏安法测定秋水仙碱，阳性峰电位为０．８２Ｖ（ｖｓ．ＳＣＥ），峰电流与秋水仙碱的浓度在１．０×１０＾－７～１．０×１０＾－４ｍｏｌ／Ｌ范围内呈良好线性关系，检测下限为５．０×１０＾－８ｍｏｌ／Ｌ回收范围为９５．０％～１０３．５％ＲＳＤ为２．８％（ｎ＝１０）。本对反应机理进行了初步探讨。     

碳糊电极吸附伏安法测定痕量钒

研究了钒 荧光镓(LMG)络合物在碳糊电极上的吸附伏安行为,发现其在+0.81V(vs.SCE)的阳极二次导数峰电流与钒(V)的浓度在一定范围内呈线性关系。在pH=4.3的0.26mol/L的HAc NH4Ac缓冲溶液中,于+0.4V富集,从+0.4至+1.4V以300mV/s线性扫描,方法线性范围为4.0×10-9～1.0×10-7mol/L(5.0×10-7mol/LLMG)和1.0×10-7～1.2×10-6mol/L(2.0×10-6mol/LLMG),检出限为1.0×10-9mol/L(S/N=3)。该法用于煤飞灰,粉煤灰和水样中钒的测定,结果满意。     

Trace Determination of Chromium by Square‐Wave Adsorptive Stripping Voltammetry on Bismuth Film Electrodes

This works reports the use of adsorptive stripping voltammetry (AdSV) for the trace determination of chromium on a rotating‐disk bismuth‐film electrode (BFE). During the reductive accumulation step, all the chromium species in the sample were reduced to Cr(III) which was complexed with cupferron and the complex was accumulated by adsorption on the surface of a preplated BFE. The stripping step was carried out by using a square‐wave (SW) potential‐time voltammetric signal. Electrochemical cleaning of the bismuth film was employed, enabling the same bismuth film to be used for a series of measurements in the presence of dissolved oxygen. The experimental variables as well as potential interferences were investigated and the figures of merit of the method were established. Using the selected conditions, the 3σ limit of detection for chromium was 100 ng L^?1 (for 120 s of preconcentration) and the relative standard deviation was 3.6% at the 2 μg L^?1 level (n=8). Finally, the method was applied to the determination of chromium in real samples with satisfactory results.