原位聚合法制备聚酰胺/聚苯胺复合导电纤维

研究了原位聚合法制备聚酰胺/聚苯胺导电纤维,并对制备的复合纤维进行红外及光学显微镜测试,结果表明聚苯胺与纤维成功复合。对制备的复合纤维进行电导率测试,采用控制单一变量法探讨了苯胺单体在不同的条件下聚合对纤维电导率的影响,并讨论了反应温度对聚合过程和电导率的影响,得出最佳的工艺条件为:纤维经30%的甲酸溶液预处理20min,苯胺单体浓度为0.8M,氧化剂过硫酸铵浓度为1M,掺杂酸为盐酸,浓度为0.8M,冰水浴条件,反应时间为4h,得到的聚酰胺/聚苯胺导电纤维的电导率为3.7S/m。     

苯胺在十二烷基苯磺酸/水体系中的乳液聚合过程研究

利用光学显微镜和扫描电镜,对以水为介质、十二烷基苯磺酸(DBSA)为乳化剂的苯胺乳液聚合过程进行监测,发现苯胺在水体系中与DBSA反应形成DBSA-苯胺盐的棒状聚集结构,讨论了DBSA、苯胺、氧化剂的配比及浓度对聚合过程中棒状聚集结构的长度和数量及生成聚苯胺的电导率的影响,提出苯胺在DBSA/水体系中的乳液聚合反应是在胶束表面进行的,而棒状聚集结构中的DBSA-苯胺盐单体经水相扩散到乳胶粒子中,形成颗粒状的聚苯胺.     

聚苯胺的化学合成及表征

本工作利用化学方法合成了具有较高电导率的聚苯胺.研究了聚合条件如反应介质的pH值,不同种类的酸及其浓度,氧化剂的用量对聚合的影响.用红外光谱、X-射线衍射、DSC等方法表征了所得的聚合物,并研究了该聚合物的掺杂反应.     

盐酸掺杂制备导电性聚苯胺的工艺优化研究

掺杂是获得高导电性聚苯胺的重要手段.本文采用盐酸进行掺杂,通过实验研究了不同条件下盐酸掺杂对聚苯胺基本性能的影响,优化了制备聚苯胺的工艺条件.当过硫酸铵与苯胺比为1时,聚合产率高达66.14%;当盐酸浓度为1.5mol/L时,室温下反应12h导电性最好.制备了聚苯胺样品,并对样品进行了FT-IR、SEM、XRD测试.结果均表明盐酸掺杂聚苯胺的反应主要发生在醌环上,掺杂后聚苯胺有一定的结晶性,且呈微纳米颗粒状、分布均匀,电导率达到1.29S·cm~(-1).正交试验得出的优化工艺为:盐酸浓度为1.0mol·L~(-1),氧化剂与苯胺单体摩尔比为1∶1,室温条件下反应4h.     

氧化剂对PAn/PTFE复合导电膜结构和性能影响的研究

分别以过硫酸铵和正钒酸钠作氧化剂,应用膜相渗透原位化学聚合法制备聚苯胺(PAn)/聚四氟乙烯(PTFE)复合导电膜,比较考察了两种氧化剂条件下膜孔中苯胺的聚合生长行为.扫描电镜、孔径分布及电化学测试结果表明:选用两种氧化剂分别制备的复合膜,均具有较小的膜孔径;与过硫酸铵相比,使用正钒酸钠作氧化剂时,复合膜的结构更为致密,且在保持较高表面电导率(2.62S·cm-1)的同时,断面电导率提高了1～2个数量级,电化学活性增强.     

无模板法聚苯胺纳米管的制备及表征

以过硫酸铵(APS)为氧化剂,在无模板,无掺杂酸条件下,利用超声辅助合成了聚苯胺纳米管.通过透射电子显微镜、傅里叶红外光谱、紫外-可见光谱、X-射线衍射对产物的形貌、结构和性能进行了表征.研究表明,形成的聚苯胺纳米管内径约为10 nm,外径约为80 nm,长度约为26μm,且管径均匀.苯胺单体浓度越高,聚合速率越快.但是,聚苯胺的形貌与苯胺单体的浓度无关,而与苯胺和过硫酸铵的摩尔比有关.超声在纳米管的形成中起主要作用,它阻止球状胶束无规则团聚,使得在较高的苯胺浓度下(0.2 mol/L)也可形成纳米管.合成的聚苯胺电导率为5×10-3S·cm-1,结晶度不高.     

FeCl_3/APS复合氧化剂对乳液法合成聚苯胺动力学行为的影响

采用石英晶体微天平(QCM)技术,探讨了以三氯化铁(FeCl3)和过硫酸铵(APS)为复合氧化剂,十二烷基苯磺酸(DBSA)为乳化剂和掺杂剂时,苯胺(An)的乳液聚合动力学行为;并通过对产物的循环伏安分析,初步优化了聚合反应条件.结果表明,An的乳液聚合反应对复合氧化剂、An以及DBSA分别为1,0.5和0.5级.各种条件下的循环伏安(CV)图都显示出PAn的三对氧化还原特征峰.当FeCl3与APS物质的量比为2∶1;氧化剂总量与苯胺的物质的量比为3∶1;DBSA浓度为0.05mol/L时,CV测试的峰电流和电导率最大.     

不同铁盐氧化掺杂导电聚苯胺纳米结构的合成及性能研究

在没有外加掺杂剂的条件下,以FeCl3,Fe(NO3)3,Fe2(SO4)3,FePO4等多种铁盐为氧化剂,在水溶液中采用"无模板"的方法制备了具有较高电导率的聚苯胺纳米结构.铁盐是一种强酸弱碱盐,在水溶液中发生水解释放出质子,质子可以作为掺杂剂进入聚苯胺主链,因此,在苯胺的聚合过程中,铁盐同时起到氧化剂和掺杂剂的双重功能,进一步简化了导电聚苯胺纳米结构的合成条件,降低了反应成本.FTIR,UV-Vis,XRD等结构表征证实所得的纳米结构的聚苯胺均为掺杂态.试验发现,铁盐较低的氧化/还原电位使产物具有较小的直径和较高的电导率和结晶性.不同的对阴离子对聚苯胺产物的形貌有一定的影响,但对产物的结构和性能影响不大.铁盐与苯胺单体的比例对聚苯胺的形貌和电导率均有较大的影响.     

高锰酸钠去除水中苯胺的不可逆过程热力学研究

苯胺在城市污水中大量存在,常采用氧化剂去除水中的苯胺.本文利用不可逆过程热力学理论,对高锰酸钠去除水中苯胺的动力学进行了研究,得到了与实验数据拟合较好的三次关系式.结果表明,在PH值及温度恒定的条件下,高锰酸钠及苯胺的初始浓度对苯胺的去除效果有影响.     

氯化铁氧化掺杂的聚苯胺纳米纤维团簇

没有外加质子酸的条件下,以氯化铁为氧化剂和掺杂剂,在界面体系中由苯胺(An)采用“无模板”的方法成功地制备了电导率为10-2～10-1S/cm的聚苯胺纳米纤维(d=20～30nm).实验证明FeCl3同时起到氧化剂和掺杂剂的双重作用,从而进一步简化了导电聚苯胺纳米纤维的合成条件.与使用过硫酸铵为氧化剂的传统聚合方法相比,FeCl3较小的氧化/还原电位使产物具有较小的直径和较高的结晶性.同时发现聚苯胺的形貌和电导率均与[FeCl3]/[An]的比例有关.FTIR,UV-Vis,XRD结构表征证实所得的聚苯胺纳米纤维为掺杂态.     

苯胺乳液聚合条件的研究

以（ＮＨ４）２Ｓ２Ｏ８为氧化剂、在非极性溶剂－功能质子酸－水三相体系中,采用乳液聚合方法合成聚苯胺乳液和粉末。对乳液聚合与化学氧化溶液聚合合成的聚苯胺性能进行了比较,研究了掺杂酸、氧化剂、反应时间、温度和水相浓度等聚合条件对聚苯胺导电性、溶解性、乳液粘度等性能的影响。结果表明,乳液聚合产率大于８０％,聚苯胺电导率大于１Ｓ／ｃｍ,在有机溶剂中的溶解性与用化学氧化合成的聚苯胺相比有明显提高。     

Conductive Composite Materials of Polyethylene and Polypyrrole with High Modulus and High Strength

Composite films of polyethylene (PE) and polypyrrole (PPy) were prepared by polymerization of PPy on an ultradrawn polyethylene film with high modulus and high strength in ferric chloride (FeCl₃) aqueous solution. The electrical conductivity of the composite film was found to be related to the polymerization conditions, such as polymerization temperature, polymerization time, the concentration and the oxidation potential of the FeCl₃ solution. Scanning electron microscopy, FTIR and ¹³C NMR spectra were used to elucidate the morphological and structural variations of PPy prepared under different conditions, which lead to the differences in the electrical properties of the resultant composite films. The best electrical conductivity of the composite was about 5.5 S/cm for the film prepared under optimum conditions. The Young's modulus and the tensile strength reached 80 GPa and 3.2 GPa, respectively, which indicated the successful production of a conductive polymer with high strength and high modulus.     

聚丁基噻吩的合成及性能

用化学聚合方法合成了聚丁基噻吩导电材料,并研究了不同的聚合条件对聚合物性能的影响。聚丁基噻吩导电材料具有较好的稳定性和加工性,其掺杂态的导电率可达到10s/cm。     

水介质中吡咯的电化学聚合反应

研究了扫描电位上限对循环伏安法制备聚吡咯膜性能的影响，吡咯在水溶液中于玻碳电极表面化学聚合的起始电位为0．58V，在聚吡咯（Ppy）修饰电极表面聚合的起始电位为0．55V，当聚合电位上限在0．80V以上时，Ppy的氧化还原反应可逆性变差，同时，氧化电位过高将导致Ppy膜导电性能下降；研究了聚合介质对循环伏安法制备导电聚吡咯膜的影响，实时观察了吡咯（Py）聚合过程溶液中质子含量的动态变化，发现Py聚合伴随有质掺杂←→释放过程；结合Ppy膜的元素分析、ESR分析和IR光谱分析，总结出了水介质中电化学聚合高导电性聚吡咯膜的条件。     

乙炔在钒催化体系下的聚合

本工作采用三乙酰基丙酮钒及二乙酰基氧钒同烷基铝组成的催化体系,研究了乙炔聚合的规律及聚乙炔成膜的条件,并初步研究了聚乙炔膜的链节结构、形态结构及室温电导率。     

聚丁基噻吩的电化学合成及性能研究

丁基噻吩在硝基苯溶液中以六氟磷酸四丁基季铵盐为支持电解质，在恒电流条件下进行电化学氧化聚合，通过电导率的测量及可见──紫外光谱分析，讨论了单体浓度、电解质浓度、电流密度、聚合温度对聚合物膜的导电性能的影响。扫描电镜图表明，随着聚合的进行．膜的表面呈“菜花”状结构。循环伏安图表明聚了基噻吩与聚噻吩具有相近的氧化峰位。     

Preparation and characterization of polyaniline-containing Na-AlMCM-41 as composite material with semiconductor behavior

Composite material formed from a mesoporous aluminosilicate, Na-AlMCM-41, with conducting polyaniline (PANI) has been synthesized by an in situ polymerization technique. Studies of aniline adsorption over mesoporous Na-AlMCM-41 synthesized in our laboratory allowed us to find the modes in which aniline interacts with the active sites of Na-AlMCM-41. In order to obtain the best reaction conditions to polymerize aniline onto Na-AlMCM-41, aniline was first polymerized to produce pure PANI. Hence, the oxidative in situ polymerization was carried out by two procedures, differing in the polymerization time and in static or stirring conditions. Studies of infrared spectroscopy and UV-vis spectroscopy indicated that higher polymerization time and static conditions allowed us to obtain mainly polyaniline in emeraldine form on the host. The N(2) isotherm of the polyaniline/Na-AlMCM-41 composite (PANI/MCM) indicated that the shape was similar to that of MCM, but the shift to saturation transition to lower partial pressure shows that the channels are occupied by PANI and they are now narrowed. The thermal properties of PANI, Na-AlMCM-41, and composite were investigated by TGA analyses and we found that the polymer shows higher thermal stability when it is forming the composite. Scanning electron microscopy indicated that PANI is not on the outer surface of the host. Conductivity studies show that PANI/Na-AlMCM-41 exhibits semiconductor behavior at room temperature and its conductivity was 7.0 x 10(-5) S/cm, smaller than that of pure polyaniline. PANI/Na-AlMCM-41 conductivity shows an increase as temperature increases. Magnetic measurements at room temperature confirmed that the composite has paramagnetic behavior; at lower temperatures the composite became diamagnetic.     

聚苯胺／聚乙烯醇导电复合膜的制备及性质研究

用较简单的化学氧化现场吸附聚合法（ｉｎ－ｓｉｔｕｐｏｌｙｍｅｒｉｚａｔｉｏｎ）制得了聚苯胺（ＰＡｎ）／聚乙烯醇（ＰＶＡ）导电复合膜．该膜具有较好的导电性和机械性能；其电导率可达５．８ｓ／ｃｍ，拉伸强度达１３ＭＰａ，断裂伸长率为１１０％左右．本文讨论了制备的各种条件对复合膜导电性能及力学性能的影响、稳定性及电化学活性；并采用循环伏安曲线、扫描电镜（ＳＥＭ）、ＦＴＩＲ谱及元素分析对该复合膜的结构和性能进行了表征．     

Synthesis and properties of latex particles with polyaniline shells

Core–shell polyaniline–latex particles have been obtained via oxidative polymerization of aniline hydrochloride in the presence of charged polystyrene latex. The polymerization conditions have been determined under which polyaniline is predominantly formed on the surface of latex particles to yield closed shells. The dependence of the electrical conductivity of the resulting particles on the initial concentration of aniline hydrochloride in the polymerization medium has been studied. Stable aqueous dispersions of polyaniline–latex particles have been prepared by modifying the particles with sodium 3-mercaptopropane sulfonate.     

Emulsion synthesis of nanoparticles containing PEDOT using conducting polymeric surfactant: Synergy for colloid stability and intercalation doping

Poly(3,4‐ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS) is a widely used conductive aqueous dispersion synthesized by using emulsion polymerization method. To further enhance its solution processability and conductivity of PEDOT derivatives, we proposed to replace the nonconductive PSS with conductive poly[2‐(3thienyl)‐ethoxy‐4‐butylsulfonate] (PTEB) as surfactant for the emulsion polymerization of PEDOT. The reaction involved colloid stabilization and doping in one step, and yielded PEDOT:PTEB composite nanoparticles with high electrical conductivity. Contrary to its counterpart containing nonconductive surfactant, PEDOT: PTEB showed increasing film conductivity with increasing PTEB concentration. The result demonstrates the formation of efficient electrical conduction network formed by the fully conductive latex nanoparticles. The addition of PTEB for EDOT polymerization significantly reduced the size of composite particles, formed stable spherical particles, enhanced thermal stability, crystallinity, and conductivity of PEDOT:PTEB composite. Evidence from UV–VIS and FTIR measurement showed that strong molecular interaction between PTEB and PEDOT resulted in the doping of PEDOT chains. X‐ray analysis further demonstrated that PTEB chains were intercalated in the layered crystal structure of PEDOT. The emulsion polymerization of EDOT using conducting surfactant, PTEB demonstrated the synergistic effect of PTEB on colloid stability and intercalation doping of PEDOT during polymerization resulting in significant conductivity improvement of PEDOT composite nanoparticles. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2536–2548, 2008