Studies on the liquid-liquid phase distribution equilibria of selenium,and its measurement in water using extraction plant with a pulsation column

Normal heptane, xylene, and a 0.01 molar solution of 4-(5-nonyl)pyridine in toluene have been investigated as extractants for selenium(IV) from nitric acid media in potassium iodide. Various parameters affecting the distribution of the element are investigated. Extraction at high aqueous to organic phase volume ratio has been studied, using a liquid-liquid extraction plant with a pulsation column. The results have been employed to measure selenium in spiked water samples.     

Determination of trace quantities of selenium by indirect atomic-absorption spectrophotometry

The selenium(IV)-iodide interaction in acid medium, leading to the liberation of iodine, has been utilized for the indirect determination of selenium by atomic-absorption spectrophotometry (AAS). The iodine is extracted into benzene and subsequently reductively stripped into an aqueous solution of ascorbic acid. After extraction of the resulting iodide as tris(1,10-phenanthroline)cadmium(II) iodide into nitrobenzene, the cadmium content of the organic extract is determined by AAS. Beer's law is applicable up to 0.75 ppm of selenium. The few interferences are readily overcome. The chemical yield in the system is about 80% overall.     

Solid phase extraction for the speciation and preconcentration of inorganic selenium in water samples: A review

Selenium is an essential element for the normal cellular function of living organisms. However, selenium is toxic at concentrations of only three to five times higher than the essential concentration. The inorganic forms (mainly selenite and selenate) present in environmental water generally exhibit higher toxicity (up to 40 times) than organic forms. Therefore, the determination of low levels of different inorganic selenium species in water is an analytical challenge. Solid-phase extraction has been used as a separation and/or preconcentration technique prior to the determination of selenium species due to the need for accurate measurements for Se species in water at extremely low levels. The present paper provides a critical review of the published methods for inorganic selenium speciation in water samples using solid phase extraction as a preconcentration procedure. On the basis of more than 75 references, the different speciation strategies used for this task have been highlighted and classified. The solid-phase extraction sorbents and the performance and analytical characteristics of the developed methods for Se speciation are also discussed.     

Interference from iodide in the determination of trace level selenium

The rate of the reaction between iodide and selenium(IV) at trace levels to form selenium and iodine has been determined in 1-6M hydrochloric acid. The reaction rate increases rapidly with acidity. When hydrochloric acid is added to reduce selenate to selenite prior to the determination of total selenium, some selenium may be lost by reduction to the element if iodide is present. A table of half-lives of the selenite-iodide reaction under various conditions is presented. A method for removal of iodide is suggested.     

Continuous approach for ultrasound-assisted acid extraction-minicolumn preconcentration of chromium and cobalt from seafood samples prior to flame atomic absorption spectrometry.

A rapid and sensitive method has been proposed for the determination of chromium and cobalt in seafood samples by flame atomic absorption spectrometry combined with a dynamic ultrasound-assisted acid extraction and an on-line minicolumn preconcentration. The use of diluted nitric acid as extractant in a continuous mode at a flow rate of 3.5 mL min(-1) and room temperature was sufficient for quantitative extraction of these trace metals from seafoods. A minicolumn containing a chelating resin was an excellent device for the quantitative preconcentration of chromium and cobalt prior to their detection. A flow-injection manifold was used as interface for coupling all analytical steps, which allowed the automation of the whole analytical process. A Plackett-Burman experimental design was used as a multivariate strategy for the optimization of both sample preparation and preconcentration steps. The method was successfully applied to the determination of chromium and cobalt in seafood samples.     

On the use of solid phase ion exchangers for isolation of amino acids from liquid samples and their enantioselective gas chromatographic analysis

This work focuses on the development of a suitable working procedure for preconcentration of amino acids enantiomers from water samples using a solid phase extraction. The three types of ion exchangers with various capabilities have been used. The effect of experimental conditions in SPE procedure employing strong anion exchange (SAX), weak (WCX) and strong cation exchange (SCX) cartridges (such as sample volume, pH, origin of elution solvent and its volume) on effective preconcentration of the model set of amino acids has been studied in detail. The enantiomers of isolated and preconcentrated amino acids have been analysed by GC on three capillary columns coated with chiral selectors. The different amino acids derivatives have been investigated in order to achieve optimal resolution of biogenic amino acids and their enantiomers. The best separation of amino acid enantiomers has been obtained on a Chirasil-L-Val column analysing their N-TFA methyl esters. It has been shown that SCX-SPE cartridge with sulfonic groups attached on silicagel support is most suitable for isolation and preconcentration of amino acids from water samples. For this sample treatment procedure, the overall recovery of extraction process has been calculated as an average value from three measurements. It has been found, that recoveries are practically identical for both enantiomers of a particular amino acid and varies in the range 75-99% depending on the type of amino acid. The effectivity of this sample preparation and GC method has been verified by preconcentration of amino acids from orange juice fortified by racemic mixture of some selected amino acids.     

Sequential spectrophotometric determination of trace amounts of periodate and iodate in water samples after micelle-mediated extraction

A cloud point extraction process using the nonionic surfactant Triton X-114 for extraction and preconcentration of periodate and iodate ions from aqueous solution was investigated. The method is based on the extraction of triiodide ion, the colored product of the reaction of periodate and iodate with iodide in acidic media. The triiodide was concentrated in surfactant rich phase and then determined spectrophotometrically at 358 nm. For the determination of periodate and iodate in mixture, two sets of conditions were established. In one set of conditions only periodate reacted with iodide but in the other set both ions reacted with iodide. The data were evaluated by the method of proportional equations. The optimal extraction and reaction conditions (e.g., surfactant and reagent concentrations and centrifuge time) were studied and the analytical characteristics of the method (e.g., limit of detection, linear range, preconcentration factor, and enhancement factors) were obtained. Under the optimized conditions, the methods allowed the determination of periodate and iodate at concentrations between 2.0 and 1000 and 4.0 and 400 ng/mL, respectively. The proposed method was successfully applied to the determination of periodate and iodate in water samples.     

Spectrophotometric determination of bromide (and iodide) in a flow system after oxidation by peroxodisulphate

The peroxodisulphate method for the determination of bromide has been modified. A flow-injection system for the spectrophotometric finish has been developed and the size of the ion-exchange column in the preconcentration step has been scaled down. The sum of bromate and iodate produced in the oxidation is determined by treating the oxidized sample with iodide in hydrochloric acid. The iodate is separately determined by applying the reaction in acetic acid. The working range of the spectrophotometric finish is 1-15muM and the limit of determination (10 sigma) is 0.7muM for iodate and for iodate plus bromate. The enrichment factor in the preconcentration step is 50, yielding a limit of determination of 15nM for bromide in natural waters. Eighteen samples of water from the Baltic, with salinity ranging from 3 to 33%. have been analysed. A Br/Cl ratio of (1.53 +/- 0.02) x 10(-3) was found. A comparative study of the original and the new preconcentration step has been made with three river waters, rich in humic substances. The results agreed within +/- 1. 5%.     

In situ synthesis and preconcentration of cetylpyridinium complexed hexaiodo platinum nanoparticles from spent automobile catalytic converter leachate using cloud point extraction

In the present study, a green chemistry based cloud point extraction (CPE) method has been developed for the in situ synthesis and preconcentration of cetylpyridinium complexed hexaiodo platinum nanoparticles (Pt-I NP) from the leachate of spent automobile catalytic converter using potassium iodide (KI) and assisted by a combination of cationic and non-ionic surfactants; cetylpyridinium bromide (CPB) and Triton X-114, respectively. The process parameters such as concentrations of hydrochloric acid, platinum, KI, sodium chloride, CPB, Triton X-114; incubation temperature and complexation time on CPE were optimized. The synthesized nanoparticles were characterized by UV–visible spectroscopy (UV–vis), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and zeta potential techniques. The formation of Pt-I NP was followed with UV–vis. The XRD pattern established the tetragonal crystal structure of the produced nanoparticles. The nanoparticles were spherical in shape and the particle size obtained with TEM was about 5.6 nm. Further, the preconcentrated nanoparticles were quantified by continuum source electro-thermal atomic absorption spectrometry (ET-AAS) and a preconcentration factor of 25 was obtained for a reaction volume of 25 mL. The accuracy of the developed method was confirmed by analyzing the certified reference materials such as CCRMP PTM-1a (copper-nickel sulphide matte) and CCRMP PTC-1a (copper-nickel sulphide concentrate). The current CPE protocol demonstrates advantages such as simultaneous synthesis and preconcentration; synthesis at micromolar concentration from metal scrap, higher nanoparticle recovery; biodegradability and biocompatibility of the employed surfactants and dual solubility of the synthesized Pt-I NP. Thus, the developed method can be applied for the separation, large scale synthesis and preconcentration of Pt-I NP from various environmental and industrial wastes, in a single pot.     

Liquid-phase microextraction and gas-chromatographic determination of selenium(IV) in aqueous samples

A liquid-phase microextraction (LPME) method was employed for preconcentration of selenium as piazselenol complex in aqueous samples. The samples reacted with o-phenylenediamine in 0.1?M HCl at 90°C for 15?min, and then LPME was performed. A microdrop of carbon tetrachloride was applied as the extracting solvent. After extraction, the microdrop was introduced directly into the injection port of gas chromatography for analysis. Several important extraction parameters such as the type of organic solvent, sample and organic drop volumes, salt concentration, stirring rate, and exposure time were controlled and optimized. In the proposed LPME, the extraction was achieved by suspending a 3?µL carbon tetrachloride drop from the tip of a microsyringe immersed in 12.5?mL of aqueous solution. Under optimized conditions, a dynamic linear range was obtained in the range of 20–1000?µg?L^?1. The preconcentration factor and the limit of detection of selenium in this method were 91 and 0.9?µg?L^?1, respectively. The optimized procedure was successfully applied to the extraction and determination of selenium in different types of real samples. The relative standard deviations for the spiking levels of 50–100?µg?L^?1 in the real samples were in the range of 3.2–6.1%, and the relative errors were located in the range of ?5.4 to 5%.     

Selective photometric determination of selenium in aqueous media

A procedure is developed for the photometric determination of selenium in aqueous media using 2-(p-nitrophenyl)-3,5-diphenyltetrazolium chloride. To selectively determine selenium, a two-stage scheme of sample preparation is chosen. It includes the gas extraction of selenium liberated as hydrogen selenide, its extraction from the gas phase to a solution of lead nitrate by liquid absorption and repeated extraction of hydrogen selenide, followed by its absorption with an aqueous reagent solution to form water-insoluble formazan. The formazan is extracted with chloroform. The concentration of selenium is determined from the absorbance of the chloroform extract of formazan. The procedure involves no special preconcentration operations and allows from 10 to 100 μg/L selenium to be determined.     

Arsenic colorimetry with silver diethyldithiocarbamate

The effect of 22 interferences had been studied. Sulfur(II) must be oxidized by nitric acid; germanium, nitric acid, and perchloric acid must be removed by repeated evaporation with hydrochloric acid. Antimony, phosphate, selenium, tellurium, iron, tin, copper, nickel, and many other elements are eliminated by extraction of arsenic(III) chloride in concentrated hydrochloric acid with p-xylene or benzene. Metal ions forming complex or insoluble iodide can be blocked with an excess of potassium iodide. The method enables the determination of 2–30 μg of arsenic with a relative error <10%. It was tested with the materials of copper production.     

Determination of trace amounts of Sb,Pb, Tl in water samples by inductively coupled plasma atomic emission spectrometry after a diantipyrylmethane-iodide third phase preconcentration

A preconcentration method based on third phase extraction has been developed and combined with inductively coupled plasma atomic emission spectrometry (ICP-AES) for determination of Sb, Pb, Tl at trace levels in water samples. The reagents diantipyrylmethane and potassium iodide were applied for complexing Sb, Pb, Tl and producing a third phase extraction system. This third phase system produces relatively large enrichment factors and complete isolation of trace elements from high salt-containing matrices which influence strongly the plasma condition. Experimental parameters of the extraction, such as concentrations of complexing reagents, pH and extraction time have been optimized. Under the selected conditions, this third phase ICP-AES combination procedure gave multielemental detection limits for Sb, Pb, Tl which are superior by an order of magnitude or more to those obtained by ICP-AES alone without preconcentration. Precision of the technique is better than 10% at the 10 g/l level. The accuracy of this approach is demonstrated by its application to tapwater, artificial seawater and reference seawater samples.     

Selective extraction of Hg(II) from aqueous mineral acid solution containing iodide ions using 2-benzylpyridine in benzene

A method for the selective extraction of mercury has been developed. The extraction of Hg(II) by 2-benzylpyridine (BPy) in benzene from dilute mineral acid solution containing iodide ions has been investigated, and variables such as concentration of acids, iodide and the extractant have been optimized. The optimum conditions for the extraction of Hg(II) by 0.1M BPy/benzene are: 0.01M (HCl, HNO₃, H₂SO₄)+0.01M KI. The distribution coefficients and separation factors of 19 elements relative to Hg(II), have been reported. Effect of anions such as ascorbate, acetate, citrate, oxalate and thiosulfate has also been studied. The method developed could find useful applications in selective extraction of small amounts of mercury from environmental samples.     

超声辅助酶法提取-原子荧光光谱法测定富硒黑木耳中硒形态

建立了富硒黑木耳中硒代胱氨酸、硒代半胱氨酸、亚硒酸、硒蛋氨酸、硒酸5种硒形态的液相色谱-原子荧光光谱分析方法。通过链酶蛋白酶E酶解,结合超声提取后,选取Hamilton PRP-X100离子交换色谱柱(250 mm×4.1 mm,10μm),40 mmol/L的磷酸氢二铵为流动相,在16 min内,5种硒形态完全达到基线分离。5种硒形态在线性范围内相关系数R为0.9990~0.9999;加标回收率为76.1%~108%;检出限分别为硒代胱氨酸0.35μg/L、甲基-硒代半胱氨酸0.46μg/L、亚硒酸0.26μg/L、硒代蛋氨酸0.64μg/L、硒酸3.06μg/L;方法应用于富硒黑木耳中硒形态的分析,精密度高、重现性好、方法稳定、准确可靠,是测定富硒黑木耳中硒形态含量的有效方法。     

Determination of trace elements in acid rain by reversed-phase extraction chromatography and neutron activation

A preconcentration neutron activation analysis (PNAA) method involving reversed-phase extraction chromatography on 8-hydroxyquinoline-loaded Amberlite XAD-2 resin has been developed for the simultaneous determination of selected trace elements in acid rain and natural water samples. Quantitative retention has been achieved for Co, Cu, Hg, V and Zn at pH 6.0 and for Cd at pH 7.0. Various factors that can influence the preconcentration procedure have been studied in detail. Concentrations of the elements have been determined by the direct irradiation of the resin without eluting them from the column. Both precision and accuracy of the PNAA method are very good. The detection limits vary between 0.01 and 3 ppb.     

Miniaturized fiber-in-tube solid-phase extraction as the sample preconcentration method for microcolumn liquid-phase separations

Miniaturized fiber-in-tube solid-phase extraction (fiber-in-tube SPE) has been developed as a solventless sample preconcentration technique for microcolumn liquid-phase separation methods. Short capillaries packed with polymer filaments were employed as the extraction tube and the preconcentration power for phthalates in aqueous solutions was studied. On the basis of the successful on-line coupling of this preconcentration method with liquid chromatography (LC), a more miniaturized extraction cartridge, which is installed in the rotor of the micro-injector, has been developed. With a modified commercially available valve, on-line coupling of this sample preconcentration method to capillary electrochromatography (CEC) was also investigated.     

Determination of tellurium in copper, lead and selenium by atomic-absorption spectrometry after extraction of the trioctylmethylammonium-tellurium bromide complex

A simple, rapid and sensitive combined solvent extraction and atomic-absorption spectrometric method has been developed for the determination of tellurium in copper, lead, selenium and blister copper. Tellurium is extracted as the trioctylmethylammonium-tellurium(IV) bromide complex into butyl acetate and determined by flame atomic-absorption spectrometry of the extract. As little as 1 mug of tellurium in a sample can be determined. The extraction of tellurium from hydrobromic acid solution with trioctylamine has also been investigated.     

Determination of total selenium in water by atomic-absorption spectrometry after hydride generation and preconcentration in a cold trap system

A cold trap system for the determination of selenium by hydride generation-atomic absorption spectrometry (HG-AAS) is described. For a 30-ml sample the limit of detection is <2 ng/l. and the precision is better than 4% at the 30 ng/l. level. A number of digestion procedures for the destruction of organic matter prior to the determination of total dissolved selenium in water has been tested and compared. Concordant results were obtained except for oxidation by peroxodisulphate in strongly acidic solutions with a high content of organic material. The selenium concentrations found were in agreement with those obtained by HG-AAS after preconcentration by evaporation and dry ashing with the magnesium nitrate-nitric acid-hydrochloric acid method.     

First derivative of the ratio spectra method for resolving iodide and thiocyanate in binary mixtures

A new method is described to analyse the binary mixture of iodide (I(-)) and thiocyanate (SCN(-)) ions, using the first derivative of the ratio spectra obtained by mathematical treatment of the data. The method is based on the formation of mixed ligand complexes between benzohydroxamic acid (BHA), vanadium (V) and I(-) or SCN(-) and their extraction in ammonium quaternary salt dissolved in toluene. Calibration graphs for 2-9 mug/ml of I(-) and for 2-6 mug ml of SCN(-) were established by measuring the analytical signals at 376 nm for I(-) and at 400.6 nm for SCN(-). The method has been applied for determining both ions in waste water of an power station at ng/ml levels after a preconcentration step with C(18), without any separation step.