Determination of potassium in sea-water by capillary isotachophoresis

Summary A new analytical procedure for the determination of potassium in sea-water was developed using capillary isotachophoresis and ion-exchange. After the sea-water sample was passed through the column packed with an ammonium form cation-exchange resin, sodium ion was removed with 2×10^–2 mol/l ammonium chloride solution and then potassium ion was eluted with 3×10^–1 mol/l ammonium chloride solution. Simultaneous determination of potassium and sodium ions was performed with a newly developed electrolyte system; the leading electrolyte was 5 mmol/l cesium hydroxide containing 2 mmol/l 18-crown-6, 0.01% hydroxypropyl methylcellulose (HPMC) and 70% methanol; the terminating electrolyte was 5 mmol/l tetrabutylammonium bromide containing 0.01% HPMC and 70% methanol. A large amount of ammonium in the eluate did not interfere with the isotachophoretic measurement of potassium and sodium ions. A linear working curve was obtained for artificial sea-water samples containing up to 700 mg/l potassium ion. The proposed method was applied to the determination of potassium in surface and bottom sea-water samples.

---

Kaliumbestimmung in Meereswasser durch Capillar-Isotachophorese

     

Ion chromatography on chelating stationary phases: separation of alkali metals

Analytical 250x4.6 mm I.D. columns packed with iminodiacetic acid (IDA) derivatised silica were used to separate alkali metal ions and the ammonium ion in combination with non-suppressed conductivity detection. The addition of 2.5-10 mmol/l of the macrocyclic crown ether 18-crown-6 to the nitric acid eluent resulted in a change in the elution order and a significant improvement in the resolution between potassium and ammonium because of selective complexation of potassium. However, the admixture of 15-crown-5 did not improve the resolution of lithium and sodium, although 15-crown-5 is a selective complexing agent for sodium. Retention and resolution of lithium, sodium, ammonium, cesium, rubidium and potassium ions increased at lower temperatures down to 1 degree C. The simultaneous separation of alkali and transition metals under isocratic conditions was achieved with an eluent comprising 10 mmol/l 18-crown-6, 1.5 mmol/l dipicolinic acid, and 1.9 mmol/l nitric acid. The chromatographic system enabled the quantitation of alkali metal ions with detection limits in the low ppb range and excellent linearity. Finally, the applicability of the method was approved by quantitation of sodium, ammonium and potassium in different water samples.     

Determination of the potassium content of explosive residues using miniaturised isotachophoresis

A new method has been developed to allow the determination of potassium in post-explosion residues to be made using miniaturised isotachophoresis. The method is based on the use of a caesium leading ion with 4.5 mM 18-crown-6 ether added to retard the potassium to allow reliable determinations to be made. With the conditions selected no interference was noted from other small inorganic cations, such as ammonium, barium, calcium, magnesium, sodium or strontium. The method was successfully applied to the analysis of seven samples containing explosive residues obtained from the unconfined burning of several flash powders. The procedure was found to offer good linearity for potassium determinations over the concentration range of 1.25-150 μg/mL with a coefficient of determination of 0.999 achieved.     

Reaktionen von Kaliumiodomercurat(II) mit Kronenethern und Kryptanden: Kristallstrukturen von Bis[di(benzo-15-krone-5)kalium]-, Di[(benzo-18-krone-6)kalium]-, Di[(cryptand 221)kalium]und Di[(cryptand 222)kalium]-hexaiododimercurat(II)

Reactions of Potassium Iodomercurate(II) with Crown Ethers and Cryptands: Crystal Structures of Bis[di(benzo-15-crown-5)potassium]-, Di[(benzo-18-crown-6)potassium]-, Di[(cryptand 221)potassium]-, and Di[(cryptand 222)potassium] Hexaiododimercurate(II) The reactions of potassium iodomercurate(II) with the crown ethers benzo-15-crown-5, and benzo-18-crown-6, resp. as well as with the cryptands 221 and 222 were investigated. In all cases only the potassium ion was complexed. As anions only hexaiododimercurate(II) ions were formed but no higher oligomers. If the complexed potassium ion is not completely shielded by the ligand, further coordination by terminal iodine atoms of the mercurate anions takes place, leading to the formation of dimers or chains.     

Single complexation force of 18-crown-6 with ammonium ion evaluated by atomic force microscopy

The cation complexation force of 18-crown-6 has been measured in ethanol by means of atomic force microscopy using probe tips and mica substrates modified chemically with 18-crown-6 and ammonium ion, respectively. The specific complexation force was suppressed by free potassium ion in the measurement solution, indicating a blocking effect based on the competitive complexation of the 18-crown-6 moiety between the free ion and the ammonium ion bound to the substrate. The single complexation force of 18-crown-6 with ammonium ion was evaluated to be about 60 pN in ethanol by autocorrelation analyses of the histograms for observed forces.     

Thermodynamics of Complexation of 18-Crown-6 with NH4+ Ion in Water-Dioxane Mixtures

The stability constants of 1 : 1 complexes of ammonium ion with 18-crown-6 in water and aqueous dioxane (dioxane weight fraction 0.2, 0.4, 0.6, and 0.8) in the range 283-318 K were determined electrometrically, and the thermodynamic parameters of the complexation were calculated. The stability of the complexes is determined by the enthalpy factor. The contributions from the Gibbs energy of solvation of NH₄ ⁺ ion, 18-crown-6·NH₄ ⁺ complex, and free 18-crown-6 to stabilization of the complex with increasing content of dioxane in the mixed solvent were estimated. The thermodynamics of complexation of ammonium, sodium, and potassium ions with 18-crown-6 in aqueous-organic solvents, such as water-2-propanol, water-acetone, and water-dioxane, were compared considering the effects of reactant solvation. The variations of the conformational component of the Gibbs energy of solvation of 18-crown-6 and the parameters of selective solvation of the reactants were evaluated. The influence of the dielectric permittivity and donor-acceptor properties of mixed aqueous-organic solvents on the Gibbs energy of complexation and solvation of the cations and 18-crown-6 was subjected to correlation analysis.     

毛细管区带电泳技术快速分离检测爆炸残留物中的无机离子

利用间接紫外毛细管区带电泳方法完成了对爆炸残留物中7种无机离子(K+,NH+4,NO-2,NO-3,SO2-4,ClO-3,ClO-4)的分离检测。阳离子测定采用的缓冲体系为10 mmol/L吡啶（pH 4.5）-3 mmol/L冠醚,K+和NH+4在2.6 min内达到基线分离,检出限分别为0.25 mg/L和0.10 mg/L(S/N=3)。阴离子测定采用的缓冲体系为40 mmol/L硼酸-1.8 mmol/L重铬酸钾-2 mmol/L硼酸钠（pH 8.6）,氢氧化四甲铵为电渗流改性剂,5种阴离子在4.6 min内达到基线分离,检出限为0.10～1.85 mg/L。该方法已成功地应用于实际爆炸物样品种类的判定分析,取得了很好的结果。     

Simultaneous determination of inorganic and organic anions,alkali, alkaline earth and transition metal cations by capillary electrophoresis with contactless conductometric detection

Simultaneous separation of up to 22 inorganic and organic anions, alkali, alkaline earth and transition metal cations was achieved in less than 3 min in the capillary electrophoresis system with contactless conductometric detector. The sample was injected from both capillary ends (dual opposite end injection) and anionic and cationic species were detected in the center of the separation capillary. The parameters of the separation electrolyte, such as pH, concentration of the electrolyte, concentration of complexing agents and concentration of 18-crown-6 were studied. Best results were achieved with electrolytes consisting of 8 mM L-histidine, 2.8 mM 2-hydroxyisobutyric acid, 0.32 mM 18-crown-6 at pH 4.25 or 9 mM L-histidine, 4.6 mM lactic acid, 0.38 mM 18-crown-6 at pH 4.25. Other electrolytes containing complexing agents such as malic or tartaric acid at various concentrations could also be used. The detection limits achieved for most cations and anions were 7.5 - 62 micro gL(-1) except for Ba2+ (90 micro gL(-1)), Cd 2+, Cr 3+ and F- (125 micro gL(-1)), and fumarate (250 micro gL(-1)). The repeatability of migration times and peak areas was better than 0.4% and 5.9%, respectively. The developed method was applied for analysis of real samples, such as tap, rain, drainage and surface water samples, plant exudates, plant extracts and ore leachates.     

Determination of the ammonium ion by voltammetry at the liquid-liquid interface using calixarenes as neutral carriers

The transfer of alkali and alkaline earth metal ions and ammonium ions facilitated by the calixarenes 5,11,17,23-tetra(tert-butyl)-26,28-dihydroxycalix[4]-25,27-crown-5-ether, 5,11,17,23-tetra(tert-butyl)-26,28-di(ethoxycarbonylmethoxy)calix[4]-25,27-crown-5-ether, and 5,11,17,23-tetra(tert-butyl)-25,26,27,28-tetra(ethoxycarbonylmethoxy)-calix[4]arene was studied by voltammetry at the interface between two immiscible electrolyte solutions. The formal energies, transfer potentials, stoichiometry, and stability constants of the complexes were determined. The optimum conditions for determining the ammonium ion by voltammetry at the liquid-liquid interface were selected on the basis of these studies (the detection limit was 3.5 × 10^?6 M). The ammonium ion determination showed selectivity relative to the sodium ion.     

Electrodialytic separation of potassium ions from sodium ions in the presence of crown ether using a cation-exchange membrane

The separation of potassium and sodium ions from their mixture was performed by electrodialyzing a mixed solution of potassium chloride and sodium chloride in the presence of 18-crown-6 using a commercial cation-exchange membrane. After 18-crown-6 had been impregnated in the membrane, the mixed solution containing 18-crown-6 was electrodialyzed as the desalting-side solution. The permeation of potassium ions through the membrane decreased remarkably and the electrical resistance of the membrane increased during electrodialysis with increasing concentration of 18-crown-6 in the solution. Because potassium ions form a more stable complex with 18-crown-6 than sodium ions and because the complex permeated through the membrane with difficulty, sodium ions are thought to selectively permeate through the membrane. The current efficiency in electrodialysis was greater than 97.0%. Received: 1 June 1999/Accepted in revised form: 13 August 1999     

毛细管区带电泳技术快速分离检测爆炸残留物中的无机离子

利用间接紫外毛细管区带电泳方法完成了对爆炸残留物中7种无机离子(K+,NH+4,NO-2,NO-3,SO2-4,ClO-3,ClO-4)的分离检测。阳离子测定采用的缓冲体系为10 mmol/L吡啶（pH 4.5）-3 mmol/L冠醚,K+和NH+4在2.6 min内达到基线分离,检出限分别为0.25 mg/L和0.10 mg/L(S/N=3)。阴离子测定采用的缓冲体系为40 mmol/L硼酸-1.8 mmol/L重铬酸钾-2 mmol/L硼酸钠（pH 8.6）,氢氧化四甲铵为电渗流改性剂,5种阴离子在4.6 min内达到基线分离,检出限为0.10～1.85 mg/L。该方法已成功地应用于实际爆炸物样品种类的判定分析,取得了很好的结果。     

腙型双冠醚对碱金属的配位性能

本文报道了五个腙型双冠醚的合成。电导测定结果表明含苯并-15-冠-5单元的双冠醚与四苯基硼酸钾、铷、铯,含苯并-18-冠-6单元的双冠醚与四苯基硼酸铯生成2:1夹心型配合物(冠醚单元:金属离子)。并用这些双冠醚的氯仿溶液萃取苦味酸碱金属盐水溶液,测定了萃取百分率和计算了萃取平衡常数,结果表明腙型双冠醚的萃取能力及选择性优于相应的单冠醚。     

Determination of thallium in potassium chloride and electrolyte replenishers by electrothermal atomic absorption spectrometry

Thallium in potassium chloride and electrolyte replenishers was determined by electrothermal atomic absorption spectrometry (ETAAS) with direct injection of a resin suspension. Thallium(III) was extracted on fine particles of a cellulose nitrate resin (CNR) from dilute HCl (pH 1.6) in the presence of ammonium pyrrolidine-1-carbodithioate. The CNR particles were collected on a membrane filter by filtration under suction, suspended in 1.0 mL 10mM HNO3, and then delivered directly to ETAAS as the suspension. The effects of chloride ions were thoroughly investigated. The results showed that the addition of 0.5mM NaCl to the suspension (10mM HNO3) was recommended, after CNR and a membrane filter holding the CNR were washed thoroughly with 0.025M HCl, to eliminate interference from chloride ions. No chemical modifier was required. Extraction from the solution containing up to 2M chloride ion was allowable. The proposed method gave a concentration factor of 50 for a 50 mL sample volume. The detection limit (3sigma, n = 5) was 1 ng (20 pg/mL). The relative standard deviation was 4.9% (n = 5) at 30 ng level of thallium. The content of thallium in potassium chloride was 15.7-32.8 ng/g, and in electrolyte replenishers was 0.18-4.16 ng/mL.     

Application of a contactless conductometric detector for the simultaneous determination of small anions and cations by capillary electrophoresis with dual-opposite end injection

A contactless conductometric detection (CCD) system for capillary electrophoresis (CE) with a flexible detection cell was applied for the simultaneous determination of small anions and/or cations in rain, surface and drainage water samples. The applied frequency, the amplitude of the input signal, the electrolyte conductivity and electrode distance were found to be the most significant factors affecting the detection sensitivity. 2-(N-Morpholino)ethanesulfonic acid/histidine-based (MES/His) electrolytes were used for direct conductivity detection of anions and cations, while ammonium acetate was selected for indirect conductivity determination of alkylammonium salts. For the simultaneous separation procedure, involving dual-opposite end injection, an electrolyte consisting of 20 mM MES/His, 1.5 mM 18-crown-6 and 20 microM cetyltrimethylammonium bromide provided baseline separation of 13 anions and cations in less than 6 min. The detection limits achieved were 7-30 micrograms/l for direct conductometric detection of various common inorganic cations and anions, excluding F- (62 micrograms/l) and H2PO4- (250 micrograms/l), and 35-178 micrograms/l for indirect conductometric detection of alkyl ammonium cations. The developed electrophoretic method with conductometric detection was compared to ion chromatography.     

含嘧啶环的双冠醚——Ⅲ.用双冠醚作载体的PVC膜离子选择性电极性质的研究

合成了九种用嘧啶环桥联的新的双冠醚,其中分别含有苯并-12-冠-4、(1、47)、苯并-15-冠-5(2、5、8)和苯并-18-冠-6(3、6、9 )。用它们作为载体分别制成钠、钾和铯离子选择性电极,测定了电极的选择性系数。结果表明,电极(7)(8)(9)具有较好的性能。     

Two-component polymer films of palladium and fullerene with covalently linked crown ether voids: effect of cation binding on the redox behavior

Redox active films have been generated via electrochemical reduction in a solution containing palladium(II) acetate and fulleropyrrolidine with covalently linked crown ethers, viz., benzo-15-crown-5 and benzo-18-crown-6. In these films, fullerene moieties are covalently bonded to palladium atoms to form a polymeric network. Films show ability to coordinate alkali metal cations from the solution. Therefore, in solutions containing salts of alkali metal cations, benzo-15-crown-5-C₆₀/Pd and benzo-18-crown-6-C₆₀/Pd films are doped with cations coordinated by crown ether moiety and anions of supporting electrolyte which enter the film to balance positive charge. These films are electrochemically active in the negative potential range due to the reduction of the fullerene moiety. Reduction of the polymer is accompanied by the transport of supporting electrolyte ions between solution and solid phase. In solution containing alkali metal salts, the process of film reduction is accompanied by the transport of anions from the film to the solution. In the presence of tetra(alkyl)ammonium salts, transport of cations from the solution to the film takes place during the polymer reduction.     

Novel polyurethanes with macroheterocyclic (crown-ether) structures in the polymer backbone

The synthesis of a functionalized crown ether was accomplished in two steps by condensing 3,4-dihydroxybenzaldehyde with bis(2-chloroethyl)ether and subsequent reduction of the reaction product, bis(formylbenzo)-18-crown-6 (4) to a diol (5). Polyurethanes that bear the dibenzo-18-crown-6 moiety in the polymer backbone were synthesized from bis(methylolbenzo)-18-crown-6 (5), a polypropylene glycol, and methylene bis(4-cyclohexyl isocyanate). The resulting polymers were fibrous white solids with glass transitions from ca. 15–120°C, depending on the starting diol composition. The thermomechanical spectra of melt pressed or solvent cast films of several crown-ether-bearing polyurethanes showed evidence of multiphase character. The polymers failed to complex effectively with sodium ions. However, their complexing ability with potassium ion was similar in magnitude to that observed with relatively simple crown ethers.     

Experimental and theoretical study of the coordination of 1,2,4-triazolato, tetrazolato, and pentazolato ligands to the [K(18-crown-6)]+ fragment

Treatment of 3,5-diisopropyltriazole, 3,5-diphenyltriazole, 3,5-di-3-pyridyltriazole, phenyltetrazole, pyrrolidinyltetrazole, or tert-butyltetrazole with equimolar quantities of potassium hydride and 18-crown-6 in tetrahydrofuran at ambient temperature led to slow hydrogen evolution and formation of (3,5-diisopropyl-1,2,4-triazolato)(18-crown-6)potassium (88%), (3,5-diphenyl-1,2,4-triazolato)(tetrahydrofuran)(18-crown-6)potassium (87%), (3,5-di-3-pyridyl-1,2,4-triazolato)(18-crown-6)potassium (81%), (phenyltetrazolato)(18-crown-6)potassium (94%), (pyrrolidinyltetrazolato)(18-crown-6)potassium (90%), and (tert-butyltetrazolato)(18-crown-6)potassium (94%) as colorless crystalline solids. (1,2,4-Triazolato)(18-crown-6)potassium was isolated as a hemi-hydrate in 81% yield upon treatment of 1,2,4-triazole with potassium metal in tetrahydrofuran. The X-ray crystal structures of these new complexes were determined, and the solid-state structures consist of the nitrogen heterocycles bonded to the (18-crown-6)potassium cationic fragments with eta2-bonding interactions. In addition, (3,5-diphenyl-1,2,4-triazolato)(tetrahydrofuran)(18-crown-6)potassium has one coordinated tetrahydrofuran ligand on the same face as the 3,5-diphenyl-1,2,4-triazolato ligand, while (3,5-di-3-pyridyl-1,2,4-triazolato)(18-crown-6)potassium forms a polymeric solid through coordination of the distal 3-pyridyl nitrogen atoms to the potassium ion on the face opposite the 1,2,4-triazolato ligand. The solid-state structures of the new complexes show variable asymmetry in the potassium-nitrogen distances within the eta2-interactions and also show variable bending of the heterocyclic C2N3 and CN4 cores toward the best plane of the 18-crown-6 ligand oxygen atoms. Molecular orbital and natural bond order calculations were carried out at the B3LYP/6-311G(d,p) level of theory on the model complex, (phenyltetrazolato)(18-crown-6)potassium, and demonstrate that the asymmetric potassium-nitrogen distances and bending of the CN4 core toward the 18-crown-6 ligand are due to hydrogen bond-like interactions between filled nitrogen-based orbitals and carbon-hydrogen sigma orbitals on the 18-crown-6 ligands. Calculations carried out on the model pentazolato complex (pentazolato)(18-crown-6)potassium predict a structure in which the pentazolato ligand N5 core is bent by 45 degrees toward the best plane of the 18-crown-6 oxygen atoms. Such bending is induced by the formation of intramolecular nitrogen-hydrogen-carbon hydrogen bonds. Examination of the solid-state structures of the new complexes reveals many intramolecular and intermolecular nitrogen-hydrogen distances of < or =3.0 A which support the presence of nitrogen-hydrogen-carbon hydrogen bonds.     

Evaluation of microchip capillary electrophoresis with external contactless conductivity detection for the determination of major inorganic ions and lithium in serum and urine samples

The determination of inorganic ions in clinical samples in less than 90 seconds was demonstrated for microchip capillary electrophoresis using capacitively coupled contactless conductivity detection (C(4)D). Bare electrophoresis chips were used in combination with external electrodes which were part of the chip holder. In order to achieve the required selectivity and sensitivity, an optimization of the electrode layout was carried out. Limits of detection (LOD) of 1 microM for K(+), 1.5 microM for Ca(2+), 3 microM for Na(+), 1.75 microM for Mg(2+) and 7.5 microM for Li(+) were achieved. The determination of inorganic cations (NH(4)(+), K(+), Na(+), Ca(2+), Mg(2+)) and anions (Cl(-), NO(3)(-), SO(4)(2-), phosphate) in blood serum and urine samples was possible in one common electrolyte solution containing 15 mM L-arginine, 10.75 mM maleic acid and 1.5 mM 18-crown-6 at pH 5.90 by simply switching the separation voltage from positive to negative polarity. Lithium, present at significant levels when used for therapeutic purposes, can also be determined in blood serum using a slightly modified background electrolyte solution.     

Analysis of leachable and total trace metals in air particulate matters by capillary electrophoresis

A new analytical procedure was developed for simultaneous determination of ammonium, leachable and total metals in fine and coarse air particulate matters using a new capillary electrophoresis (CE) procedure, with a new buffer system containing 10 mM histidine, 2 mM 18-crown-6 and 8 mM lactic acids with pH adjusted to 4.0. A two complexes system, 18-crown-6 ether and lactic acid, was developed to solve the co-migration problem of NH(4)(+) and K(+) and to give satisfactory separation of transition metals. Satisfactory separation and quantitation of NH(4)(+), K(+), Ca(2+), Na(+) , Mg(2+) and Zn(2+) were obtained using the CE procedure developed for both leachable and total metals in coarse (10-3 mum) and fine (<3 mum) air particulate matters. Wide working ranges (ppb to ppm range) and sensitive detection limits (ppb) were obtained for the cations investigated. The reliability was established by parallel method comparison with the ICP-AES method. The analytical procedure developed is shown to provide a quick, sensitive, precise and economic method for simultaneous determination of ammonium, leachable and total metals in air particulate matters.