Determination of hydrazine derivatives by flow-injection analysis with spectrophotometric detection

Flow-injection analysis for the determination of hydrazine derivatives based on their nucleophilic substitution reaction with 4-chloro-5,7-dinitrobenzofurazan in aqueous medium, and spectrophotometric detection has been described. The calibration graphs were linear in the range from 0.15 to 4.0 mug ml(-1) of hydrazine derivatives, with sampling rates of up to 28-32 samples h(-1). Interferences from amino compounds, benzoic acids, aliphatic amines and ammonia have been evaluated. The procedure has been applied to the determination of hydrazine derivatives in serum, urine, appressin drugs and artificial mixtures.     

Determination of uranium in seawater by flow-injection preconcentration on dodecylamidoxime-impregnated resin and spectrophotometric detection

A flow injection method has been developed for the determination of uranium in seawater combining the on-line preconcentration with spectrophotometric detection. An aliquot (10 mL) of the seawater sample adjusted to pH 5.5 was injected into the analytical system and uranium was adsorbed on the column packed with styrene-divinylbenzene copolymer resin (Bio-Beads SM-2) modified with dodecylamidoxime which showed high selectivity to uranium. Uranium was then eluted with 0.01 M hydrochloric acid and detected spectrophotometrically after the reaction with Chlorophosphonazo III. Interference from calcium and strontium was masked with cyclohexanediaminetetraacetic acid added to the chromogenic reagent solution. The sample throughput, the detection limit (3σ), and the preconcentration factor were 23 per hour, 0.13 μg/L, and 20, respectively, when the sample injection volume was kept at 10 mL. The precision at the 2 μg/L level was less than 4% (RSD). The proposed method was applied to the determination of uranium in the seawater samples collected off the Boso peninsula, Japan and the uranium concentration was found to be ca. 3 μg/L, which is close to the literature data. The yield of the recovery test ranged from 95% to 99%.     

Integrated retention/spectrophotometric detection in flow-injection analysis : Determination of Iron in Water and Wine

An integrated retention/spectrophotometric method is proposed for the determination of iron based on the Fe (III)-thiocyanate complex. The method has good selectivity, with a determination limit of 10 ng ml^?1 and a linear range of 10–400 ng ml^?1. Different types of measurements (peak height, absorbance increment, tangent curve) are shown to have their particular advantages. The method is applied to the determination of iron in natural water and wine, with an average recovery of 100.3% and 98.8% and an average deviation of the recovery of 2.5% and 1.6%, respectively.     

Indirect spectrophotometric determination of ascorbic acid with ferrozine by flow-injection analysis

A FIA indirect spectrophotometric determination of ascorbic acid was developed using its reducing action on Fe(III) in acidic medium and following the spectrophotometric determination of the reduced iron by using sodium 3-(2-pyridyl)-5,6-diphenyl-1,2,4-triazine-4',4'-disulphonate (ferrozine) as chromogenic reagent in buffered medium (pH 5.5) and monitoring the absorbance signal at 562 nm. A three-line manifold with two reaction coils was used: in the first reaction coil, ascorbic acid reduces Fe(III) to Fe(II); and in the second one, the complexation reaction is developed. The linear range of the method was 0.5-10 mug ml(-1) of ascorbic acid, the detection limit being 0.028 mug ml(-1). The proposed method was sensitive, rapid (sampling rate of 90 samples h(-1)) and reproducible (RSD 0.19%, n=10). Satisfactory results were obtained in the determination of ascorbic acid in pharmaceutical preparations, fruit juices and urine testifying the applicability of the method to real samples.     

Determination of cyanide and thiocyanate by a spectrophotometric flow-injection method

A rapid spectrophotometric flow-injection method is described for the determination of cyanide and thiocyanate. The method involves a two-step procedure in which the total concentration of both species is first determined (using sodium isonicotinate/sodium barbiturate reagents), after which the cyanide is complexed with nickel(II) and thiocyanate is quantified separately; the cyanide concentration is calculated by difference. Various parameters such as pH, temperature and nickel concentration were optimized. The method is applied to synthetic sample solutions and the results are compared with those obtained by the ASTM distillation method. The limits of detection for cyanide and thiocyanate are 0.05 and 0.08 μg ml^?1, respectively, with a sample throughput rate of 10 h^?1.     

Determination of thorium with DBF-arsenaz by flow-injection analysis

A sensitive,selective,rapid,simple,and convenient method for the determination of thoriumwas developed.The method was based on the color reaction of thorium with DBF-arsenazo in astrong acidic medium (4 mol/L HCI).The flow-injection technique was used with an automated flow-injection analyzer.Beer's law was obeyed in the range of 0—1.4 μg/mL.The relative standarddeviations were less than 1%.     

Automated method for the determination of boron in water by flow-injection analysis with in-line preconcentration and spectrophotometric detection

A sensitive, automated method for the determination of boron in water samples is described, involving flow injection with on-line ion-exchange preconcentration and spectrophotometric detection of the azomethine-H—boron complex. The method is applicable to various water samples and is free from interferences, even in coloured samples. Detection limits of 5 μg l^?1 at 20 samples h^?1 and 1 μg l^?1 at 10 samples h^?1 with relative standard deviations of < 10% at 1–10 μg l^?1 and < 5%at 10–200 μg l^?1 levels of boron were achieved. The recoveries for spiked natural water samples ranged from 96 to 101%. The method compares favourably with inductively coupled plasma atomic emission spectrometry.     

Simultaneous spectrophotometric determination of nitrite and nitrate by flow-injection analysis

An automatic direct spectrophotometric method for the simultaneous determination of nitrite and nitrate by flow-injection analysis has been developed. Nitrite reacts with 3-nitroaniline in the presence of hydrochloric acid (0.96-1.8 M HCl or pH 0.5-0.7) to form a diazonium cation, which is subsequently coupled with N-(1-naphthyl)-ethylenediamine dihydrochloride to form a stable purple azo dye, the absorbance of which is measured at 535 nm. Nitrate is reduced on-line to nitrite in a copper-coated cadmium column which is then treated with azo dye reagent and the absorbance due to the sum of nitrite and nitrate is measured; nitrate is determined from the difference in absorbance values. A copper column incorporated into the reaction manifold before the copperised cadmium column not only improves the long-term accuracy, but also extends the life time of the copperised cadmium column. Various analytical parameters, such as effect of acidity (pH), flow rate, sample size, dispersion coefficient, time, temperature, reagent concentration and interfering species, were studied. The calibration graphs were rectilinear for 0.1-3.5 mug ml(-1) of NO(3) and 10 ng ml(-1)-2.2mug ml(-1) of NO(2). The method is successfully applied to some food samples (meat, flour and cheese), environmental waters (inland and surface), beer and soil samples. Up to 30 samples can be analysed per hour with a relative precision of approximately 0.1-2%.     

Determination of formaldehyde by its catalytic effect on the oxidation of pyrogallol red by bromate using flow-injection spectrophotometric detection

This paper reports a simple and sensitive flow-injection method for the spectrophotometric determination of formaldehyde based on the catalytic effect of formaldehyde on the oxidation of pyrogallol red with bromate in acidic media. The decrease in absorbance of the reaction mixture was measured at 470 nm. The calibration graph was linear in the range of 0.47 to 40.0 μ/mL formaldehyde for a sample rate of 30±5 samples per hour. The limit of detection is 0.36 μ/mL. The relative standard deviations for ten replicate measurements of 2.5, 5.0, and 20.0 μ/mL formaldehyde were 3.9, 2.1, and 0.7%, respectively. The method was applied to the determination of formaldehyde in river water, shampoo, and melamine-formaldehyde resin. The text was submitted by the authors in English.     

流动注射胶束化学发光法测定曲克芦丁

基于HCl介质中曲克芦丁与KIO4-MnSO4反应产生强的化学发光,且吐温-80的存在能使这一反应的化学发光强度大大增强。结合流动注射技术,建立了流动注射化学发光法测定曲克芦丁的新方法。在优化的实验条件下,曲克芦丁的质量浓度在2.0×10-7~8.0×10-5g/mL范围内与化学发光强度呈良好的线性关系,检出限为7×10-8g/mL。对1.0×10-6g/mL曲克芦丁进行11次平行测定,方法的相对标准偏差为1.8%。用于曲克芦丁片剂和针剂中曲克芦丁的测定。     

流动注射胶束化学发光法测定西咪替丁的研究

在碱性条件下K3Fe(CN)6可直接氧化西咪替丁产生化学发光信号,吐温-80的存在可大大增强此反应的化学发光强度。基于此,建立了胶束流动注射化学发光法测定西咪替丁的新方法。在优化的实验条件下,该法的线性范围为1.0×10-7~5.0×10-4g/mL,检出限为2×10-8g/mL,相对标准偏差为1.6%(n=11,ρ=5.0×10-7g/mL)。该法已用于西咪替丁制剂中西咪替丁的测定。     

Ultraviolet spectrophotometric determination of copper in copper ores by flow-injection analysis

A flow-injection analysis (FIA) method for the ultraviolet spectrophotometric determination of copper in copper ores is described. The ore samples are dissolved in concentrated perchloric acid, the excess acid is neutralized with ammonia solution, and the resulting solution is used for the determination of copper. The UV-FIA system is based on the reaction of copper (II) ions with pyrophosphate and subsequent measurement of the absorbance of the dipyrophosphatocuprate (II) complex at 240 nm. The main factors which control the formation of this complex and the FIA variables influencing the system are discussed. The calibration graph is linear from 2-50 ppm copper. At a sampling rate of about 70 samples h(-1) with 50 mul sample injections, precision was about 1% relative standard deviation. Results obtained compare well with those obtained by atomic absorption spectrometry.     

Determination of a non-ionic surfactant in aqueous environmental samples by flow-injection analysis with chemiluminescence detection

A flow-injection procedure for the determination of a commercially available fatty amine ethoxylate-based non-ionic surfactant in sea water over the range 0–50 mg l^?1 is described. The procedure is based on measurement of the chemiluminescence emission resulting from oxidation of the tertiary amine group with sodium hypochlorite at pH 10.5 in the presence of Rhodamine B, which acts as a sensitizer.     

流动注射化学发光法测定片剂中阿昔洛韦含量

在碱性介质中,低浓度的阿昔洛韦会增强鲁米诺-H2O2体系的化学发光,据此建立了测定阿昔洛韦的新方法.该法的化学发光增强值ΔICL与阿昔洛韦的浓度在9.00×10-8～3.00×10-6mol/L范围内呈良好的线性关系,相关系数r为0.9957,检出限为7.71×10 -8mol/L.对1.00×10-6 mol/L的阿...     

Theoretical and practical aspects of acid-base determinants by spectrophotometric flow-injection analysis

A simple mathematical treatment is applied to the instantaneous acid-base equilibria prevailing at the peak maxima when reagents containing acid-base indicators are used for spectrophotometric flow-injection determinations of acids and bases. Equations are derived relating the absorbance, the fraction of the relevant acidic or basic form of the indicator and the rate of change of either form with the initial concentration of the analyte and other parameters that influence these determinations. Based on these relationships, criteria are set for the choice of reagent/indicator combinations likely to yield linear absorbance/concentration dependence for general and special cases. These considerations simplified the design of experimental work. Suitable conditions are described for the determination of hydrochloric, phosphoric and acetic acids and for sodium hydroxide and ethanolamine. Very weak acids and bases and concentrations lower than 0.01 N were not investigated, because they were not predicted to conform with the criteria for linearity presented. Least-squares treatment of the data obtained indicated a relative standard deviation of 0.5% from linear behavior, for favorable cases, over a reasonably wide concentrations range. Short-term standard deviations were 0.8% or better; long-term deviations, over several hours, were 1–2%. Highest throughput of samples examined was 144 h^?1.     

流动注射化学发光法测定己内酰胺

使用己内酰胺增强Ce(Ⅳ) SO32-化学发光体系,结合流动注射分析技术进行了己内酰胺的测定。己内酰胺的质量浓度在4.0×10-7～1.0×10-5g/mL范围内与化学发光分析信号呈线性关系,其检出限为1×10-7g/mL。对4.0×10-7g/mL的己内酰胺溶液进行11次连续测定,相对标准偏差为2.1%。方法已应用于层析用聚己内酰胺中的己内酰胺测定。     

Determination of parathion in the presence of paraoxon and p-nitrophenol by flow-injection analysis with amperometric detection

The amperometric determination of parathion in the presence of its metabolites paraoxon and p-nitrophenol in a flow-injection system is reported. The method is based on the measurement of the oxidation signal yielded by p-nitrophenol on hydrolysis of parathion in the presence of Pd(II) or Hg(II). The oxidation of the metabolite was preferred to its reduction as it avoids the removal of oxygen, which poses major problems in flow-through configurations.     

Determination of formaldehyde by flow injection analysis with spectrophotometric detection exploiting brilliant green-sulphite reaction

A method for the determination of formaldehyde by flow injection analysis with spectrophotometric detection is proposed, based on retarding the reaction between brilliant green and sulphite by the addition of formaldehyde; this was investigated for formaldehyde quantification in extracts from wood-based panels. For the first time, a heating step was explored, providing a sample throughput of 50 analyses per hour, with a limit of detection of 0.02 mg L^?1 and linearity of 0.20–3.0 mg L^?1, which was adequate for the expected range of formaldehyde concentration in the extracts. The mean recovery observed for actual samples was in the range of 92–106 %, with a maximum relative standard deviation of 6.0 %. The paired t-test revealed no significant difference between this method and the official Nash method, demonstrating an appropriate accuracy and precision; the method is proposed as a simple, fast and inexpensive alternative for the routine determination of formaldehyde in an aqueous medium.     

Determination of clotiazepam by HPLC with spectrophotometric and amperometric detection

Summary Spectrophotometric and amperometric detectors were compared for the determination of clotiazepam by HPLC. Methanol-water (6040) containing 0.01 mol/l ammonium acetate and methanol-water (7030) containing 0.01 mol/l acetate buffer pH 4 were used as mobile phase in the spectrophotometric and amperometric detection, respectively. The minimum detectability for the spectrophotometric detection was 20 ng injected and the method was applied for the determination of clotiazepam in serum, whereas for the amperometric detection a limit of detection of 2.5 g injected was obtained, using this technique for clotizepam determination in tablets.

---

Bestimmung von Clotiazepam durch HPLC mit spektralphotometrischer und amperometrischer Detektion

     

Sequential determination of iron(II) and iron(III) in pharmaceutical by flow-injection analysis with spectrophotometric detection.

A flow injection procedure for the sequential spectrophotometric determination of iron(II) and iron(III) in pharmaceutical products is described. The method is based on the catalytic effect of iron(II) on the oxidation of iodide by bromate at pH = 4.0. The reaction was monitored spectrophotometrically by measuring the absorbance of produced triiodide ion at 352 nm. The activating effect for the catalysis of iron(II) was extremely exhibited in the presence of oxalate ions, while oxalate acted as a masking agent for iron(III). The iron(III) in a sample solution could be determined by passing through a Cd-Hg reductor column introduced in the FIA system to reduce iron(III) to iron(II), which allows total iron determination. Under the optimum conditions, iron(II) and iron(III) could be determined over the range of 0.05 - 5.0 and 0.10 - 5.0 microg ml(-1), respectively with a sampling rate of 17 +/- 5 h(-1). The experimental limits of detection were 0.03 and 0.04 microg ml(-1) for iron(II) and iron(III), respectively. The proposed method was successfully applied to the speciation of iron in pharmaceutical products.