Determination of thallium in lead salts by differential pulse anodic-stripping voltammetry

The determination of trace levels of thallium in lead and lead salts by differential pulse anodic-stripping voltammetry has been made possible by using a surfactant as an electrochemical masking agent in addition to a complexing agent. In 0.2M EDTA at pH 4.5 as supporting electrolyte without surfactant, lead at concentrations below 0.5mM does not give a peak. When the electrolyte also contains tetrabutylammonium chloride (TBAC) at 0.01 M concentration, lead can be tolerated at concentrations up to 0.05M, while the height of the thallium peak is unaffected. It is thus possible to determine 5nM T1(I) in the presence of 0.05M Pb(II), i.e., Tl at the 1 x 10(-5)% level in lead. The precision of the determination (1-4%) and the recovery are satisfactory. Neither an 800-fold excess ratio of Cu(II) to Tl(I) nor a 10(7)-fold ratio of Bi(III) interferes in the determination. Thallium has been determined in a range of lead salts of various degrees of purity.     

Determination of thallium in bismuth by differential pulse anodic-stripping voltammetry without preliminary separation

The determination of trace levels of thallium in bismuth and bismuth salts by differential pulse anodic-stripping voltammetry has been made possible by using a surfactant as an electrochemical masking agent, in addition to a complexing agent. In 0.2M EDTA at pH 4.5 as supporting electrolyte in the absence of surfactant, bismuth at concentrations below 10(-4)M does not interfere. When the electrolyte also contains tetrabutylammonium ions at 0.01 M concentration, bismuth can be tolerated at concentrations up 0.05M, and the height of the thallium peak is unaffected. It is thus possible to determine 1 nM Tl(I) in the presence of 0.05M Bi(III), i.e., Tl at the 1 x 10(-6)% level in bismuth. The precision of the determination and the recovery are satisfactory. Neither an 800-fold ratio of Cu(II) nor a 10(7)-fold ratio of Pb(II) to Tl(I) interferes in the determination. Other cations such as Zn(2+), Cd(2+), In(3+), Hg(2+), Fe(3+), Sb(3+) and Sn(4+) in 10(4)-fold molar ratio to Tl(I) have no effect on the determination. Thallium has been determined in bismuth metal and in bismuth nitrate of various degrees of purity.     

Electrochemical masking of large amounts of copper in dpasv and the determination of thallium in the presence of a large excess of copper

The influence of the following surfactants on the peak of copper in 0.2M EDTA at pH 4.5 was investigated: polyoxyethylated alkylphenols having an average of 3 and 9.5 ethylene oxide units; polyoxyethylene alcohols having 4 and 7 ethylene oxide units; poly(ethylene glycols) having M.W. 4000, 9000 and 20000; hexadecyltributylphosphonium bromide (HDTBPB), tetraphenylphosphonium bromide (TPPB),N,N,N,N,N',N',N-examethylhexamethylenediammonium bromide (HMB), benzyl(di-isobutylphenoxyethoxy) dimethylammonium chloride (Hyamine 1622), hexadecyltrimethylammonium bromide (HDTMAB), hexadecyldimethylbenzylammonium chloride (HDDMBAC) and tetrabutylammonium chloride (TBAC). HDDMBAC, as well as all the substances examined which contained an ethylene oxide chain, completely suppressed the copper peak. HDTBPB and TPPB partially suppressed the peak, whereas HDTMAB, HMB and Hyamine 1622 enhanced it. TBAC was without effect. In 0.2M EDTA at pH 4.5 containing TBAC at 0.01M concentration and 10 ppm of Rokafenol N-3, Cu(II), Pb(II) and Bi(III) can be tolerated at concentrations of up to 0.05M, the height of the thallium peak being unaffected. The precision of the determination (3–10%) and the recovery are satisfactory. A 10³-fold ratio of Fe(III) to Tl(I) does not interfere with the determination.     

Preconcentration of bismuth(III) and copper(II) by solid-phase extraction and subsequent determination by differential pulse polarography

A differential pulse polarographic method is proposed for the trace determination of bismuth and copper from large volumes of aqueous samples after adsorption of their 1-(2-thiazolylazo)-2-naphthol complexes onto microcrystalline naphthalene in the pH ranges of 7.2-9.0 and 4.0-7.8, respectively. Bismuth and copper are desorbed from microcrystalline naphthalene with 9 mL 1M HCl. Well-defined peaks are obtained at Ep = -0.09 and -0.20 V versus a saturated calomel electrode, in an HCl-isoquinoline medium as the supporting electrolyte, for bismuth and copper, respectively. Bismuth is reduced reversibly with a 3-electron change, whereas copper is reduced irreversibly under these conditions. The detection limits are 55 ng/mL for bismuth and 91 ng/mL for copper. Linearity is maintained in the concentration ranges of 0.18-13.5 and 0.30-17.3 microg/mL for bismuth and copper, respectively, with corresponding correlation coefficients of 0.9996 and 0.9885. The relative standard deviations are 1.0% for bismuth at 2.0 microg/mL and 1.4% for copper at 5.0 microg/mL. Various parameters were optimized to develop conditions for the determination of these metal ions in various samples.     

Ion-exchanger colorimetry-IV microdetermination of bismuth in water

Ion-exchanger colorimetry for the microdetermination of bismuth(III) in water samples is described. The yellow bismuth-iodide complexes are specifically sorbed and concentrated on an anion-exchange resin in the sulphate form. The resin-phase absorbances at 492 and 700 nm are measured directly. Bismuth in the ppb-ppm range can be determined without interference, except in presence of a large amount of copper(II), silver(I) and lead(II). The detection limit is 6.4 x 10(-9)M, i.e., 1.3 ppb. The distribution ratio is larger than 10(7). It is, therefore, possible to enhance the sensitivity by increasing the sample volume. The method is useful for the determination of bismuth in natural waters and industrial effluents.     

Spectrophotometric determination of bismuth and EDTA by means of the reaction of bismuth with pyrocatechol violet in the presence of septonex

The reaction of bismuth(III) with Pyrocatechol Violet in the presence of the cationic surfactant Septonex was studied and the optimal conditions for its analytical use were found (lambda = 612 nm, pH = 3.1, C(PV) = 4 x 10(-5)M, C(Sept), = 5 x 10(-4)M). The Lambert-Beer law is obeyed over the bismuth range 0.1-7.5 mug/ml. Decomposition of the Bi-PV-Septonex complex was utilized for indirect determination of ethylenediaminetetra-acetic acid at concentrations of 0.3-7.4 mug/ml.     

The cloud point extraction of copper(II) with monocarboxylic acids into non-ionic surfactant phase

The possibility to use monocarboxylic acids and their mixtures with amines for copper concentrating by the way of micellar extraction at cloud point temperature, and later atomic absorption spectrometry (AAS) determination was investigated. Under the optimum conditions, preconcentration of 100 ml of water sample in the presence of 1% non-ionic surfactant OP-10, 0.005 M capric acid and 0.01 M octylamine permitted the detection of 0.01 μg ml⁻¹ copper. The proposed method has been applied to the AAS determination of copper in water samples after cloud point extraction.     

Amperometry with two polarisable electrodes-XI Determination of bismuth by EDTA titration

Optimum conditions have been found for a highly selective determination of bismuth via EDTA titration with biamperometric indication of the end-point. The influence of the applied potential, pH and stirring on the accuracy and selectivity of the determination has been studied. In a medium of 0.4M nitric acid only high concentrations of iron(III) and copper(II) interfere with the determination of bismuth. Zirconium, thallium(III) and indium interfere even in small concentrations. The average error of the determination of 5-100 mg of bismuth (when titrated with 0.05M EDTA solution) is +/-0-1 % rel. and for the determination of 0.5-10 mg it is +/-0.3% rel. (0.005M EDTA). The method has been verified by the analysis of a Wood's metal of known composition.     

Extraction,Separation and Spectrophotometric Determination of Bismuth(III) Using 1(4′-Bromophenyl) 4,4,6-Trimethyl (1H,4H)-Pyrimidine-2-Thiol

Abstract

The operating conditions for the spectrophotometric determination of bismuth(III) with 1-(4′-bromophenyl)-4,4,6-trimethyl-(1H,4H)-pyrimidine-2-thiol (4′bromo PTPT) as a ligand by a liquid-liquid extraction technique are presented. In acidic conditions bismuth(III) forms a yellow complex with the ligand which can be extracted in chloroform with an absorption maxima at 410 nm. The molar absorptivity is 1.5×10⁴ l mole^?1 cm^?1 and Sandell's sensitivity is 14.3 ng cm^?2. The difference in the absorbance between the chloroform blank and bismuth(III) sample increases linearly in the concentration range 2-14 ppm at 0.3 M hydrochloric acid. The proposed method is extremely sensitive, rapid, reproducible and has been satisfactorily applied to the determination of trace amounts of bismuth(III) in synthetic mixtures, alloys and pharmaceutical formulations and also provides binary separation of bismuth(III) from selenium, tellurium, lead, antimony, copper and gold. The overall process of extraction and determination takes about 15 to 20 min.     

Determination of thallic and thallous ions by differential pulse anodic stripping voltammetry without preliminary separation

The simultaneous determination of thallic and thallous ions, without preliminary separation, has been achieved by differential pulse anodic stripping voltammetry at a hanging mercury drop electrode. The electrochemical activity of thallic ions in 0.2M EDTA at pH 4.5 +/- 0.2 is inhibited by the addition of 0.01% poly(ethyleneglycol) of M.W. 20,000 (PEG 20,000). When the electrolyte also contains ascorbic acid at 0.01M concentration, the sum of thallic and thallous species can be determined.     

Über die Anwendung der Kohlepaste-Elektrode zur inversvoltammetrischen Bestimmung kleiner Quecksilbermengen

The applicability of the carbon paste electrode to the determination of trace quantities of mercury has been investigated in a base electrolyte of 0.1 N KSCN + 0.025 N HCl containing 25 ng/ml copper. The detection limit of the mercury determination has a value near 2.5 ng/ml (1.25×10^?8 M), if pre-electrolysis is carried out 10 min at ?1.0 V and the current voltage curve is registered with a scan rate of 16.7 mV/sec between ?0.5 and +0.5 V. The peak height is directly proportional to the concentration in the range from 1.25×10^?8 to 1.25×10^?6 M. With appropriate preconditioning the carbon paste electrode can be used for several measurements without renewing the surface.     

硒碳糊电极微分电位溶出法测定铜和铋

建立了掺杂硒碳糊电极同时测定铜和铋的微分电位溶出法。在HCl(0.05mol/L)中,在-0.3V(vs.Ag/AgCl)下,Cu2+和Bi3+电沉积在电极表面,再在溶液中溶解氧的作用下,铜和铋从电极表面溶出,分别于0.30V和0.02V获得灵敏的电位溶出峰。微分电位溶出峰高(dt/dE)与铜和铋的浓度成线性关系,线性范围为5.0×10-9～1.55×10-7mol/L,检出限分别为4.0×10-9和2.5×10-9mol/L(S/N=3)。方法用于实际样品中铜和铋的测定,结果令人满意。     

Application of adsorptive stripping voltammetry to the determination of bismuth and copper in the presence of morin

A new method is presented for the determination of bismuth and copper based on cathodic adsorptive stripping of complexes of Cu(II) and Bi(III) with 2′,3,4′,5,7-pentahydroxyflavone (morin) at a hanging mercury drop electrode (HMDE). The effect of various parameters such as pH, concentration of morin, accumulation potential and accumulation time on the selectivity and sensitivity were studied. The optimum conditions for determination of copper include nitric acid concentration 0.1 M, morin concentration 0.6 μM and accumulation potential of −300 mV. Those conditions for the determination of bismuth include 0.15 M acid concentration, 0.6 μM morin and accumulation potential of −300 mV. Under these optimum conditions and for an accumulation time of 60 s, the measured peak current at −20 to 25 mV is proportional to the concentration of copper and bismuth over the range of 0.2-130 and 5-50 ng ml⁻¹, respectively. At high concentration of morin (35 μM morin) and accumulation potential of −300 mV (versus Ag/AgCl reference electrode) the peak current is proportional only to the concentration of copper and bismuth has no contribution to the current. At low concentration of morin (0.5 μM morin) and accumulation potential of 100 mV (versus Ag/AgCl reference electrode) the peak current is proportional only to the concentration of bismuth. The method was applied to the determination of copper and bismuth in some real and synthetic samples with satisfactory results.     

Voltammetric determination of mercury(II) at a carbon paste electrode in aqueous solutions containing tetraphenylborate ion

The determination of mercury(II) ions can be achieved by monitoring the decrease in the oxidation peak of the tetraphenylborate ion in the presence of this metal ion at a carbon paste electrode. The reaction between mercury(II) and the tetraphenylborate ion results in the formation of diphenylmercury, thus providing the method with good selectivity over other metal ions. Using anodic stripping voltammetry in a neutral electrolyte, a linear dependence of the decrease of peak height was observed on increasing the mercury(II) concentration in the range 1 x 10(-6)-8 x 10(-9)M mercury(II). Zinc(II), cadmium(II), lead(II), nickel(II), cobalt(II), tin(II), potassium(I) and ammonium(I) ions did not interfere at a 1000-fold concentration excess. Iron(III) and chromium(III) did not interfere at a 250-fold and 50-fold concentration excess, respectively. Following masking procedures, copper(II), bismuth(III) and silver(I) did not interfere at a 100-fold concentration excess. The method can be used to determine the concentration of mercury(II) in natural waters contaminated by this metal.     

原子荧光光谱法测定铜合金中铋元素含量方法改进

基于原子荧光光谱法测定铋元素时检出限低、测定结果稳定且准确等优点,研究原子荧光光谱法测定铜合金中铋元素含量的方法。在标准系列中加入相近浓度的铜元素标准溶液,原子荧光光谱法测定铜合金中铋元素含量。称取0.1 g样品,加入10 mL硝酸溶解,10%硫脲-5%抗坏血酸溶液7.5 mL预处理样品。在20μg/L的铋标准溶液中加入6 mL浓度为1000μg/mL的铜元素标准溶液。结果表明:在0~20μg/L范围内,该方法线性关系良好,线性方程为I=138.1670c+43.8572,相关系数为0.9996,所测定的样品中铋元素含量的相对误差在-4.3%~7.7%之间,精密度在0.4%~4.7%之间。原子荧光光谱法可作为铜合金中铋元素含量测定的方法。     

Enhanced Resolution of Copper and Bismuth by Addition of Gallium in Anodic Stripping Voltammetry with the Bismuth Film Electrode

This paper presents the enhanced analysis of copper on a bismuth electrode upon addition of gallium(III). The presence of gallium alleviates the problems of overlapping stripping signals usually observed between copper and bismuth when using the Bismuth Film Electrode. In addition, it has been found that the presence of gallium improves the reproducibility of the bismuth stripping signal. Simultaneous deposition of copper and bismuth at ?1500 mV for 2 minutes in a supporting electrolyte composed of 0.1 M pH 4.75 acetate buffer with 250 μg L^?1 gallium yields well resolved copper and bismuth signals when analyzed with square‐wave anodic stripping voltammetry. Simultaneous analysis of copper and lead yielded linear calibration plots in the range 10 to 100 μg L^?1 with regression coefficients of 0.997 and 0.994 respectively. The theoretical detection limit for copper was calculated to be 4.98 μg L^?1 utilizing a 2 minutes deposition time. The relative standard deviation for a copper concentration of 50 μg L^?1 was 1.6% (n=10).     

A contribution to the use of chelating agents in anodic stripping voltammetry

The E(p)/(2), values of the ions Pb(2+), Bi(3+), Cu(2+), Cd(2+), Tl(+) were determined by means of cyclic voltammetry in solutions of acetate and Britton-Robinson buffers and in solutions containing EDTA and DCTA. DCTA was then utilized in the determination of small amounts of bismuth, down to 10(-7)M, in the presence of 10(4) times as much lead, and of traces of thallium down to 5 x 10(-9)M in the presence of 2 x 10(5) times as much cadmium by anodic stripping voltammetry. The precision was good. Further, the trace copper concentration in analytical grade DCTA was determined. A new flow-through vessel for stripping analysis with solution exchange is also described and the reproducibility of results without solution exchange, with manual solution exchange, and with the flow-through vessel is evaluated for a model determination of thallium in a DCTA solution.     

Simultaneous determination of copper, bismuth and lead by adsorptive stripping voltammetry in the presence of thymolphthalexone.

A novel, sensitive and selective adsorptive stripping procedure for simultaneous determination of copper, bismuth and lead is presented. The method is based on the adsorptive accumulation of thymolphthalexone (TPN) complexes of these elements onto a hanging mercury drop electrode, followed by reduction of adsorbed species by voltammetric scan using differential pulse modulation. The influences of control variables on the sensitivity of the proposed method for the simultaneous determination of copper, lead and bismuth were studied using the Derringer desirability function. The optimum analytical conditions were found to be TPN concentration of 4.0 microM, pH of 9.0, and accumulation potential at -800 mV vs. Ag/AgCl with an accumulation time of 80 s. The peak currents are proportional to the concentration of copper, bismuth and lead over the 0.4-300, 1-200 and 1-100 ng mL(-1) ranges with detection limits of 0.4, 0.8 and 0.7 ng mL(-1), respectively. The procedure was applied to the simultaneous determination of copper, bismuth and lead in the tap water and some synthetic samples with satisfactory results.     

The polarographic determination of thallium

A polarographic method is described for the determination of thallium in sodium triphosphate supporting electrolyte. The incorporation of 0.1% camphor in the electrolyte displaces the cathodic steps of many interfering ions, e.g., lead(II), copper(II), iron(III) and bismuth(III) to a more negative potential (1?.0 V), well away from the thallium step which remains unaffected.     

Self-assembled Gemini surfactant film-mediated dispersion stability

The force-distance curves of 12-2-12 and 12-4-12 Gemini quaternary ammonium bromide surfactants on mica and silica surfaces obtained by atomic force microscopy (AFM) were correlated with the structure of the adsorption layer. The critical micelle concentration was measured in the presence or absence of electrolyte. The electrolyte effect (the decrease of CMC) is significantly more pronounced for Gemini than for single-chain surfactants. The maximum compressive force, F(max), of the adsorbed surfactant aggregates was determined. On the mica surface in the presence of 0.1 M NaCl, the Gemini micelles and strong repulsive barrier appear at surfactant concentrations 0.02-0.05 mM, which is significantly lower than that for the single C(12)TAB (5-10 mM). This difference between single and Gemini surfactants can be explained by a stronger adsorption energy of Gemini surfactants. The low concentration of Gemini at which this surfactant forms the strong micellar layer on the solid/solution interface proves that Gemini aggregates (micelles) potentially act as dispersing agent in processes such as chemical mechanical polishing or collector in flotation. The AFM force-distance results obtained for the Gemini surfactants were used along with turbidity measurements to determine how adsorption of Gemini surfactants affects dispersion stability. It has been shown that Gemini (or two-chain) surfactants are more effective dispersing agents, and that in the presence of electrolyte, the silica dispersion stability at pH 4.0 can also be achieved at very low surfactant concentrations ( approximately 0.02 mM).