Highly birefringent octagonal photonic crystal fibers with two zero-dispersion wavelengths

A new highly birefringent octagonal photonic crystal fiber(Hi-Bi OPCF) with a rectangular array of four elliptical airholes in the fiber core region is proposed and analyzed using the full-vector finite element method with anisotropic perfect match layer absorbing boundaries.Numerical results show that the phase birefringence of the photonic crystal fiber(PCF) reaches 3.43×10-2 at the wavelength of 1 550 nm.Moreover,two zero-dispersion wavelengths are achieved in the visible and near infrared wavelength regions for one polarization state but not in the other.     

Transverse load sensing by use of pi-phase-shifted fiber Bragg gratings

The birefringence of a pi -phase-shifted fiber Bragg grating can be determined with high accuracy by measurement of the polarization-induced spectral splitting of its narrow central transmission window. The use of this feature for sensing of a load applied in the direction transverse to the optical fiber is demonstrated. A distributed force resolution of 1.4x10(-3) N/mm was obtained, which corresponds to a difference in the principal strains of the fiber core of 0.5mu? . We also show that the transverse load response of the sensor is insensitive to temperature.     

Passive broadband silicon-on-insulator polarization splitter

We present the implementation of a novel wavelength independent polarization splitter on a silicon-on-insulator platform. The waveguide splitter is based on a zero-order arrayed waveguide grating (AWG) configuration. The splitting function is realized by employing cladding stress-induced birefringence. The device demonstrated a TE to TM splitting ratio better than -15 dB over a 20 nm tuning range centered around lambda=1550 nm and better than -10 dB over our entire accessible wavelength range from lambda=1465 nm to 1580 nm. The highest splitting extinction ratio achieved was -20 dB. To our knowledge, this is the first reported passive broadband polarization splitter based on AWG.     

Chromatic dispersion behavior of Si-NC-Er doped optical fiber

The chromatic dispersion for conventional and Er-doped fibers using the refractive index approximation is examined. A first, analytical method for investigation of dispersion in step index triple clad optical fiber is used. To design of zero-dispersion shifted fiber for optical communication purpose manipulation of the refractive index and radius of the core are considered. We show that in presence of the Si-NC-Er ions, zero-dispersion wavelength is displaced and the dispersion quantity is increased. In this work, we try to optimize system parameters to obtain minimum dispersion and dispersion shifted fiber with control of the doping levels of Er ions and Si-NC as well as doping profiles. For especial case, we assumed the Gaussian inhomogeneous core refractive index for zero-dispersion wavelength and dispersion managements.     

Limit for pulse compression by pulse splitting

We have detected a fundamental pulse-compression limit for high-nonlinear fibers in the normal dispersion regime near the zero-dispersion wavelength. The desired generation of a broadband continuum by self-phase modulation is limited by already small amounts of third-order dispersion (TOD), which results in pulse splitting above a critical pulse power. We investigate the critical fiber length in dependence on pulse- and fiber parameters.     

Ultra-broadband supercontinuum generated in dispersion-flattened fiber

With 4.28-km dispersion-flattened fiber (DFF), more than 254.9-nm 10-dB bandwidth on the right side of zero-dispersion wavelength and a 190.4-nm wide spectral region with the uniformity of within ±0.5dB are obtained. While on the opposite side, 198.4-nm 10-dB bandwidth and 62.3-nm spectral region with the uniformity of within ±0.5 dB are obtained. More than 88 channels spaced at 2.52 nm on the long wavelength side are generated using Fabry-Perot (F-P) filter. The output supercontinuum (SC)characteristic is also analyzed by spectrum carving.     

Anti-Stokes Frequency Shift and Evolution in Polarization-Maintaining Photonic Crystal Fiber with Two-Zero Dispersion Wavelengths

Using the tunable pump pulses with about lOO fs pulse duration and 1064 nm central wavelength; the polarization-, wavelength- and power-dependent anti-Stokes lines are generated and modulated simultaneously in a polarization-maintaining photonie crystal fiber （PM-PCF） with two zero-dispersion wavelengths. By accurately controlling the polarization directions, the wavelength and the power of the pump pulse in the fiber anomalous region close to the second zero-dispersion wavelength of the PM-PCF, the output anti-Stokes pulse spectra can be tuned between 563 nm and 603 nm, which is in good agreement with the theoretical simulation. The color conversion of the mode image from yellow to orange is also observed with the different polarization pump pulses. These results can be attributed to the combined interaction between the fiber birefringence （including linear- and nonlinear- birefringence） and dispersion, and are attributed to phase-matching parametric four-wave mixing.     

具有三个及四个零色散波长光子晶体光纤的仿真研究

利用多极法对光子晶体光纤的色散特性进行了模拟, 通过设计合适的结构参数, 得到了具有3个零色散波长的单模光纤.对中心纤芯有1个微小空气孔光子晶体光纤的色散特性进行了分析, 设计出了具有4个零色散波长的色散曲线.分析了零色散波长随光纤结构的变化规律, 这些零色散波长的位置和间距可以在很大波长范围内灵活调节. 具有多个零色散波长的光纤可以得到色散值极低的超平坦色散曲线. 多个零色散波长光纤能产生丰富的相位匹配曲线, 可以有效地控制光孤子及超短脉冲的四波混频及共振散射产生的光谱特性.     

高双折射纳米结构光子晶体光纤特性研究

设计了一种高双折射高非线性纳米结构光子晶体光纤,利用电磁场散射的多极理论研究了这种光纤的双折射、基模模场、色散以及非线性特性.数值研究发现,加大纤芯及包层空气孔的非对称程度,可使双折射变大,其双折射最大值可达1.918×10-2.通过调节孔节距大小,可将双折射最大值调至所需波长处,孔节距为400nm的纳米光子晶体光纤在800nm波长处非线性系数高达0.2m-1.W-1,同时在750—1000nm的波段有较大的双折射值,高双折射和高非线性在纳米结构光子晶体光纤中实现了完美的结合.对新型纳米光子器件的研制和集成光学的发展具有重要意义.     

Simultaneous measurements of non-linear coefficient, zero-dispersion wavelength and chromatic dispersion in dispersion-shifted fibers by four-wave mixing

We report on a new simple technique for the simultaneous measurement of non-linear coefficient, zero-dispersion wavelength, and chromatic dispersion in dispersion-shifted fibers based on partially degenerated four-wave mixing. Both zero-dispersion wavelength and chromatic dispersion of the dispersion-shifted fibers can be measured with high accuracy. The experiment results of two dispersion-shifted fibers will be presented and the technique for obtaining accurate chromatic dispersion and zero-dispersion wavelength will also be discussed.     

Determination of Zero-Dispersion Wavelength by Four-Wave Mixing

We present an improved approach to determine the zero-dispersion wavelength by measurement of the four-wave mixing （FWM） effect employing the two-tunable-laser scanning method. The FWM behaviour of combined fibres with two different zero-dispersion wavelengths is investigated theoretically and experimentally. The results are compared with those by regular zero-dispersion wavelength test instrument using phase shift technique. The theoretical and experimental results confirm the feasibility of determination of zero-dispersion wavelength by FWM.     

微结构纤芯对光子晶体光纤基本特性的影响

本文设计了两种具有微结构纤芯的光子晶体光纤（PCFs）——矩形芯和椭圆芯PCFs,利用电磁场散射的多极理论研究了这两种光纤的基本特性.发现在光纤包层气孔不变的情况下,仅通过调节纤芯气孔的大小就可以灵活地调节光纤的双折射、色散和非线性特性.随着纤芯气孔半径r₁的增大,两种纤芯结构的PCFs表现出如下特点：双折射度增大且最大双折射度对应的波长发生红移,零色散波长由一个增加到三个,短波段非线性系数增大而长波段非线性系数减小.r₁=0.4 μm的椭圆芯PCFs的三个零色 关键词： 微结构纤芯光子晶体光纤 双折射 色散 非线性     

有中心缺陷孔的椭圆孔光子晶体光纤传输特性研究

基于超格子构造法,采用全矢量模型研究了具有中心缺陷孔的椭圆光子晶体光纤的传输特性。着重讨论了中心缺陷孔对光纤中基模的模场分布、双折射特性和色散特性的影响。研究表明：与椭圆孔光子晶体光纤相比。由于中心椭圆缺陷孔的引入,使该光纤具有更高的模式双折射。光纤的传输特性对光纤的结构参量和波长具有较强的依赖关系。随着波长和中心缺陷孔的增加。双折射将增大,其模式双折射在10^-3量级。改变光纤的结构参量,可以获得超宽带的色散平坦或异常的色散特性。分析结果显示,当中心孔的尺寸de／D=0．4时。在波长1．55μm附近,可获得近400nm的色散平坦区。     

Soliton Propagation near Zero-Dispersion Wavelength in Birefringence Fiber

fiom coupled nonlinear Schrodinger equation which describes the birefringence near zero-dispersion wavelength, we derive the evolution feature of soliton parameters and get the differential equation describing the evolution of interval between solitons along with propagation distance. At the same time, we have made detailed numerical research on the propagation in dissipation system of standard fundamental soliton. The result shows that for attractive potential, the distance of oscillation increases dong with the loss increases. For repulsive potential, the distance of oscillation diverges faster along with the loss increases. If selecting the proper-optical fiber of high-order dispersion, the interaction between solitons in birefringence fiber can be eliminated.     

圆芯边孔光纤的应力区和双折射

报道了圆芯边孔光纤(CSF)中应力分布和双折射的研究结果。用有限元法建立了求解圆芯边孔光纤横截面应力和双折射的计算模型,分析了圆芯边孔光纤横截面应力和应力双折射的分布形态,给出了详尽的物理解释。计算结果表明圆芯边孔光纤的横截面上出现应力分量的拉应力区和压应力区,应力区在纤芯附近对称分布,且不同应力区中应力双折射取向不同。应力分量和应力双折射在圆芯边孔光纤横截面上积分为零。圆芯边孔光纤的几何双折射随波长增加而增大,短波长处几何双折射为零,模式双折射等于应力双折射,随着波长增加,模式双折射逐渐偏离纤芯中心处应力双折射而靠近几何双折射,到长波长处模式双折射主要是几何双折射。对于不同材料组成和结构尺寸的圆芯边孔光纤,模式双折射的数值在10-5量级,随波长增加模式双折射先减小后增加。     

Differential birefringence in Bragg gratings in multicore fiber under transverse stress

We present experimental measurements of the peak splitting of the reflection spectra of fiber Bragg gratings as a result of birefringence induced by transverse loading of a multicore fiber. Measurements show that the splitting is a function of the applied load and the direction of the load relative to the azimuth of the fiber. A model for calculating the stress in the fiber that is due to an applied load is in good agreement with our experimental observations.     

Measurement of birefringence in integrated optical waveguides by use of a microwave-modulated optical wave

We present a technique for measuring birefringence (B) in integrated optical waveguides by use of a microwave-modulated optical wave. It is shown that the technique is able to yield an accurate measurement of birefringence. In addition, an approximate estimate of birefringence dispersion (dB/dlambda) can be achieved by means of tuning the wavelength of the light source and measuring the dependence of the birefringence on the wavelength. As an example of the use of the technique, we show how to evaluate an innovative Ti:LiNbO (3) waveguide. The results show that such a Ti:LiNbO (3) waveguide has a birefringence of 0.0783+/-0.0001 and a birefringence dispersion of 0.05+/-0.01mum (-1) when the optical wavelength is approximately 1.560mum .     

Soliton blueshift in tapered photonic crystal fibers

We show that solitons undergo a strong blueshift in fibers with a dispersion landscape that varies along the direction of propagation. The experiments are based on a small-core photonic crystal fiber, tapered to have a core diameter that varies continuously along its length, resulting in a zero-dispersion wavelength that moves from 731 nm to 640 nm over the transition. The central wavelength of a soliton translates over 400 nm towards a shorter wavelength. This is accompanied by strong emission of radiation into the UV and IR spectral regions. The experimental results are confirmed by numerical simulation.     

Four-wave mixing in microstructure fiber

We report what we believe to be the first experimental demonstration of nondegenerate four-wave mixing in a microstructure fiber. The effect of the chi((3)) nonlinearity is enhanced in such a fiber because of the small core area, and we achieve phase matching by operating near the zero-dispersion wavelength (?750 nm) . We have observed parametric gains of more than 13 dB in 6.1-m-long fiber with a pump peak power of only 6 W. We compare our experimental gain results with those predicted by theory and explore the effects of Raman shift and (or) amplification and cascaded nonlinear mixing.     

基于椭圆孔包层和微型双孔纤芯的新型高双折射光子晶体光纤

设计了一种新型高双折射光子晶体光纤,即其包层引入椭圆形空气孔,且以三角晶格方式周期排列,纤芯引入亚波长尺寸(~0.16 μm)的微型双孔结构阵列.采用全矢量有限元法和各向异性完美匹配层边界条件分析了该型光子晶体光纤的双折射特性和色散特性,详细介绍了该光子晶体光纤在不同的椭圆率、椭圆归一化面积、微型双孔孔径、两小孔之间间距的情况下双折射和限制损耗随波长的变化曲线.模拟结果表明,通过同时在包层和纤芯引入非对称性,获得了较高的双折射(~10^-3量级)和极低(~10^-4 dB/km)的限制损耗.提供了一种新的光子晶体光纤设计方法,即通过同时在包层和纤芯引入新结构来同时获得高双折射和低损耗.