Crystallization behavior, thermal and mechanical properties of PHBV/graphene nanosheet composites

Biodegradable poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV)/graphene nanosheet (GNS) composites were prepared via a solution-casting method at low GNS loadings in this work. Transmission electron microscopy revealed that a fine dispersion of GNSs was achieved in the PHBV matrix. The thermal properties of the nanocomposites were investigated by thermogravimetric analysis, and the results showed that the thermal stability of PHBV was significantly improved with a very low loading of GNSs. Nonisothermal melts crystallization behavior, spherulitic morphology and crystal structure of neat PHBV and the PHBV/GNSs nanocomposites were investigated, and the experimental results indicated that crystallization behavior of PHBV was enhanced by the presence of GNSs due to the heterogeneous nucleation effect; however, the two-dimensional (2D) GNSs might restrict the mobility of the PHBV chains in the process of crystal growing. Dynamic mechanical analysis studies showed that the storage modulus of the PHBV/GNSs nanocomposites was greatly improved.     

Morphology, crystallization and mechanical properties of poly(ɛ-caprolactone)/graphene oxide nanocomposites

A series of nanocomposites based on poly(ε-caprolactone) (PCL) and graphene oxide (GO) were prepared by in situ polymerization. Scanning electron microscopy observation revealed not only a well dispersion of GO but also a strong interfacial interaction between GO and the PCL matrix, as evidenced by the presence of some GO nanosheets embedded in the matrix. Effects of GO nanofillers on the crystal structure, crystallization behavior and spherulitic morphology of the PCL matrix were investigated in detail. The results showed that the crystallization temperature of PCL enhanced significantly due to the presence of GO in the nanocomposites, however, the addition of GO did not affect the crystal structure greatly. Thermal stability of PCL remarkably increased with the addition of GO nanosheets, compared with that of pure PCL. Incorporation of GO greatly improved the tensile strength and Young’s modulus of PCL without a significant loss of the elongation at break.     

A novel microwave absorber — BaAl2Fe10O19/poly(m-toluidine) composite: Preparation and electromagnetic properties

BaFe10Al2O19 /poly(m-toluidine)(BFA/PMT) composites were synthesized by in-situ polymerization of m-toluidine in the presence of BaFe10Al2O19 particles.The structure,composition and morphology of the obtained samples were characterized by using XRD,FT-IR,UV-visible spectroscopy,SEM and TEM techniques.Their electrical conductivity,magnetic property and microwave absorbing property were measured by the four-probe meter,the vibrating sample magnetometer and the vector network analyzer,respectively.The results indicated that BFA particles were coated effectively by PMT polymer and some interactions between PMT and BFA particles existing in the composites.The conductivity of BFA/PMT composite is smaller than that of pure polymers and its saturation magnetization is a little smaller than that of pure BFA.The influence of the constitution and film thickness of absorbent on its microwave absorbing property is evident.The microwave absorbing properties of the BFA/PMT composites are better than those of pure BFA and PMT.When optimizing the mass rate of BFA/PMT to 0.3,the absorbent with 2 mm film thickness has the minimum reflection loss of 28.26 dB at approximate 14.24 GHz,and the maximum available bandwidth of 8.8 GHz,respectively.The results show that these composites can be used as advancing absorption and shielding materials due to their favorable microwave absorbing property.     

Isothermal crystallization behavior and unique banded spherulites of hydroxyapatite/poly(L-lactide) nanocomposites

<正>Hydroxyapatite/poly(L-lactide)(HA/PLLA) nanocomposites were prepared by the solvent mixing method.The isothermal crystallization behavior was studied by differential scanning calorimetry(DSC) and polarized optical microscopy (POM).The results show that the crystallization behavior of HA/PLLA composites was strongly affected by the content of HA and crystallization temperature,and the addition of HA could promote nucleation and enhance the crystallization rate. When isothermal crystallization was carried out at 110℃,the HA/PLLA nanocomposite with 1%HA content crystallized most rapidly among all the composites and the half crystallization time was only 1.0 min.Banded spherulites were observed for the HA/PLLA composites,but no banded spherulites were seen in the crystals of PLLA under the same condition.     

Mechanical and thermal properties of polypeptide modified hydroxyapatite/poly(L-lactide) nanocomposites

A new type of polypeptide(poly(-benzyl-L-glutamate)(PBLG))modified hydroxyapatite(HA)/poly(L-lactide)(PLLA)nanocomposites(PBLG-g-HA/PLLA)were prepared by the solvent-mixing method,and their mechanical and thermal properties were investigated.The tensile test showed that the mechanical properties of PBLG-g-HA/PLLA nanocomposites were better than that of PLLA,even a 0.3 wt%content of PBLG-g-HA in the nanocomposites could make the tensile strength 12%higher than that of the neat PLLA sample,and the tensile mod...     

Morphological structures of poly(vinylidene fluoride)/montmorillonite nanocomposites

Poly(vinylidene fluoride) (PVDF)/montmorillonite (MMT) nanocomposites were prepared by melt blen- ding a kind of organically modified montmorillonite with PVDF. The morphological structures of the nanocomposites were studied using X-ray diffraction (XRD), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy, and differential scanning calorimetry (DSC). The re- sults indicate that organically modified montmorillonites are in the form of intercalation, exfoliation, and fragments in the PVDF matrix. For the composites, the (001) peak position of MMT was found to shift to a lower angle in XRD patterns, and some MMT fragments could be observed under TEM. MMT loading was favorable to producing the piezoelectric β phase in the PVDF matrix and caused internal stress in α crystals. At the same time, the crystallinity and spherulite size of PVDF decreased with the MMT content. MMT induced β phase is stable even at high temperatures (160℃). For these changes in morphological structures, some possible explanations were proposed based on the experimental re- sults.     

Block Copolymer Networks Composed of Poly(ε-caprolactone) and Polyethylene with Triple Shape Memory Properties

In this contribution, we reported a novel synthesis of block copolymer networks composed of poly(ε-caprolactone)(PCL) and polyethylene(PE) via the co-hydrolysis and condensation of α,ω-ditriethoxylsilane-terminated PCL and PE telechelics. First, α,ω-dihydroxylterminated PCL and PE telechelics were synthesized via the ring-opening polymerization of ε-caprolactone and the ring-opening metathesis polymerization of cyclooctene followed by hydrogenation of polycyclooctene. Both α,ω-ditriethoxylsilane-terminated PCL and PE telechelics were obtained via in situ reaction of α,ω-dihydroxyl-terminated PCL and PE telechelics with 3-isocyanatopropyltriethoxysilane. The formation of networks was evidenced by the solubility and rheological tests. It was found that the block copolymer networks were microphase-separated. The PCL and PE blocks still preserved the crystallinity. Owing to the formation of crosslinked networks, the materials displayed shape memory properties. More importantly, the combination of PCL with PE resulted that the block copolymer networks had the triple shape memory properties, which can be triggered with the melting and crystallization of PCL and PE blocks. The results reported in this work demonstrated that triple shape memory polymers could be prepared via the formation of block copolymer networks.     

Fabrication and characterization of chitosan-silk fibroin/hydroxyapatite composites via in situ precipitation for bone tissue engineering

Homogeneous chitosan-silk fibroin/hydroxyapatite(CS-SF/HA) composites were prepared by in situ precipitation method driven by a multiple-order template. The morphology of the composites was investigated by scanning electron microscope(SEM) and transmission electron microscope(TEM). The compositional analysis was carried out by X-ray diffraction analysis(XRD) and Fourier transformed infrared spectroscopy(FTIR). The mechanical properties and biocompatibility of the composites were also determined. The results indicated that the inorganic particles of uniform size(50 nm) were well-dispersed among the CS-SF matrices. The compressive modulus of the CS-SF/HA composites was enhanced with the increasing amount of SF. The in vitro results suggested that the MC3T3-E1 osteoblast-like cells on CS-SF/HA composite disks displayed strong bonding and spreading, and the cell proliferation cultured on each composite disk increased throughout the culture period for up to 7 days. Especially, the samples with higher content of SF had much better biological properties. The evidences proved that the CS-SF/HA composites possessed excellent biocompatibility. By using the freeze-drying technique, hierarchical porous scaffolds with pores ranging from 50 μm to 200 μm were obtained. This work presented the advantages of in situ precipitation method to prepare the organic/inorganic composites, and a multiple-order template was introduced in the system to improve the properties of the composites by combining the merits of each organic template.     

Preparation and characterization O-lauroyl chitosan/poly (L-lactic acid) blend membranes by solution-casting approach

O-Lauroyl chitosan/poly(L-lactide) (OCS/PLLA) blend membranes with different compositions were prepared by solution-casting approach using chloroform as common solvent. The experimental results of FT-IR, DSC and WAXD indicated that inter-association hydrogen-bond interactions existed between OCS and PLLA in the blend membranes. And SEM observation confirmed that the blend membranes with suitable compositions were compatible.     

The effect of silica morphology on properties of PVA/silica nano-composites

Two kinds of poly(vinyl alcohol)(PVA)-silica composites were prepared with different methods. One composite was prepared by directly mixing PVA with 80 nm silica nano-particles which were made from tetraethoxysilane(TEOS). The another was obtained by the mixing PVA and hydrolyzed TEOS in the presence of acid-catalyst. The properties of the two PVA/silica hybrids were characterized by means of scanning electron microscopy(SEM), UV-Visible spectroscopy,solubility tests, limiting oxygen index(LOI) test, tensile test and dynamical mechanical analysis(DMA), respectively. The results indicate that PVA-TEOS composites(PT for short) display more transparency than PVA-silica nano-particles hybrids(PS for short). At the same time, The PT composites presented more excellent performance than PS in water resistance, fire resistance and mechanical properties. Moreover, the Tg of PT increased with increasing TEOS content, while that of PS decreased.     

Crystallization Behavior and Dynamic Mechanical Properties of Poly(ε-caprolactone)/Octaisobutyl-Polyhedral Oligomeric Silsesquioxanes Composites Prepared via Different Methods

Two octaisobutyl-polyhedral oligomeric silsesquioxanes(oib-POSS)reinforced biodegradable poly(ε-caprolactone)(PCL)composites were prepared via two different methods,i.e.,melt compounding and solution casting,which were named as m PCL/oib-POSS and s PCL/oibPOSS,respectively,in this work.Oib-POSS dispersed finely in both composites;moreover,oib-POSS aggregates were larger in m PCL/oib-POSS than in s PCL/oib-POSS.Despite the different preparation methods,oib-POSS obviously promoted the crystallization of PCL,especially in s PCL/oib-POSS,but did not modify the crystal structure of PCL.The storage moduli of PCL were improved significantly in both composites.PCL/oib-POSS composites with enhanced crystallization behavior and improved dynamic mechanical properties were successfully prepared through both methods;moreover,the solution casting method was more effective than the melt compounding method.     

Efficient synthesis of poly(oxymethylene) dimethyl ethers over PVP-stabilized heteropolyacids through self-assembly

A series of polyvinylpyrrolidone-stabilized heteropolyacids(PVP-HPAs)are generated by self-assembly of HPAs and PVP in methanol.The PVP-HPAs are then employed as catalysts for the synthesis of poly(oxymethylene)dimethyl ethers(DMMn,n1)by the methanolysis of trioxane.The results suggest that the acidity of PVP-HPAs is tunable by changing the ratio of PVP and HPAs,which is a key factor for the selectivity of the DMMn product.By optimizing the composition and reaction conditions,two types of PVP-HPA,PVP-phosphotungstic acid(PVP-HPW)in a PVP/HPW ratio of 1/4:1 and PVP-silicotungstic acid(PVP-HSi W)in a PVP/HSi W ratio of 1/4:3/4,respectively afford 52.4%and 50.3%yields of DMM2–5.The optimized catalysts are reusable for a minimum of 10 times without a significant drop in performance.     

Preparation and characterization of thermosensitive poly（NIPAM-co-MAH-β-CD）/（TiO2-MWCNTs） composites by UV light photoinitiating method

In this report,a novel thermosensitive poly（N-isopropylacrylamide-comaleic anhydride-p-cyclodextrin）/（TiO₂-multi-walled carbon nanotubes）（poly（NIPAM-co-MAH-β-CD）/（TiO₂-MWCNTs）） composite was synthesized by UV light photoinitiating method.The results indicated that MAH modifiedβ-CD（MAH-β-CD） could polymerize to NIPAM by UV light irradiation in the presence of TiO₂-MWCNTs composite nanoparticles.The characteristic results confirmed that the TiO₂-MWCNTs composite nanoparticles were embedded evenly within the thermally responsive copolymer of NIPAM and MAH-β-CD.The effects of irradiation time and TiO₂-MWCNTs concentration on the yield of the composites were investigated by keeping NIPAM to MAH-β-CD mass ratio constant.The optimal polymerization reaction conditions were a TiO₂-MWCNTs concentration of 10 wt.%under UV light for the illumination of 3 h.     

Preparation of polystyrene/silica nanocomposites by radical copolymerization of styrene with silica macromonomer

A two-stage process has been developed to generate the silica-based macromonomer through surface-modification of silica with polymerizable vinyl groups. The silica surfaces were treated with excess 2,4-toluene diisocynate (TDI), after which the residual isocyanate groups were converted into polymerizable vinyl groups by reaction with hydroxypropylacrylate (HPA). Thus, polystyrene/silica nanocomposites were prepared by conventional radical copolymerization of styrene with silica macromonomer. The main effecting factors, such as ratios of styrene to the macromonomer, together with polymerization time on the copolymerization were studied in detail. FTIR, DSC and TGA were utilized to characterize the nanocomposites. Experimental results revealed that the silica nanoparticles act as cross-linking points in the polystytene/silica nanocomposites, and the glass transition temperatures of the nanocomposites are higher than that of the corresponding pure polystyrene. The glass transition temperatures of nanocomposites increased with the increasing of silica contents, which were further ascertained by DSC.     

STUDIES ON ULTRASONIC GRAFTING OF POLY(VINYL ACETATE) WITH POLY(ETHYLENE OXIDE)

The ultrasonic degradation of poly(ethylene oxide) and poly(vinyl acetate) in benzene solution, and grafting reaction of poly(vinyl acetate) with poly(ethylene oxide) were studied. It is found that the chain-scission reactions follow the course suggested by D. W. Ovenall. The structure of the copolymer was identified by IR, NMR and DTA, showing that the copolymer prepared is a graft copolymer mainly. The copolymer formed by irradiating 1% PEO/PVAc solution (PEO/PVAc:1/1 by weight) for a period of 10 rain at 18.2 kHZ, with 2.0 A input current on reversed main circuit, amounts to 10.5%.     

Improving hydrophilicity and protein antifouling of electrospun poly(vinylidenefluoride-hexafluoropropylene) nanofiber membranes

<正>Poly(vinylidenefluoride-hexafluoropropylene)(PVDF-HFP) nanofiber membranes with improved hydrophilicity and protein fouling resistance via surface graft copolymerization of hydrophilic monomers were prepared.The surface modification involves atmospheric pressure glow discharge plasma(APGDP) pretreatment followed by graft copolymerization of poly(ethylene glycol) methyl ether methacrylate(PEGMA).The success of the graft modification with PEGMA on the PVDF-HFP fibrous membrane is ascertained by X-ray photoelectron spectroscopy(XPS) and attenuated total reflectance Fourier transform infrared measurements(ATR-FTIR).The hydrophilic property of the nanofiber membranes is assessed by water contact angle measurements.The results show that the PEGMA grafted PVDF-HFP nanofiber membrane has a water contact angle of 0°compared with the pristine value of 132°.The protein adsorption was effectively reduced after PEGMA grafting on the PVDF-HFP nanofiber membrane surface.The PEGMA polymer grafting density on the PVDF-HFP membrane surface is measured by the gravimetric method,and the filtration performance is characterized by the measurement of water flux.The results indicate that the water flux of the grafted PVDF-HFP fibrous membrane increases significantly with the increase of the PEGMA grafting density.     

Synthesis and Luminescent Property of Polycarbazole/Polyhedral Oligomeric Silsesquioxane Nanocomposites

Polyvinylcarbazole（PVK） composites containing organic-inorganic hybrid polyhedral oligomeric silse-squioxane（POSS） PVK-POSS were prepared by free radical polymerization. POSS monomers reacted with vinylcarbazole and were completely dispersed at molecular level in PVK matrix and PVK-POSS nanocomposites display higher glass transition temperature（Tg） in comparison with neat PVK. Optical properties of PVK/POSS nanocomposites were investigated by UV-spectrum and PL-spectrum and the results show that the PVK-POSS nanoparticles have a good interface effect and improve color purity effectively. The maximum absorption wavelength bathochromically shifts gradually with the increasing of the content of POSS. The luminescent intensity becomes higher and higher with the increase of POSS content, and reaches its maximum luminescent intensity when the POSS content is 3% （mass fraction）, while some POSS-rich nanoparticles are present in matrix when contents of POSS are beyond 5%.     

SYNTHESIS AND CHARACTERIZATION OF ORGANOMONTMORILLONITE AND POLYAMIDE 66/MONTMORILLONITE NANOCOMPOSITES

The montmorillonites (MMTs), layered, smectite-type silicates, were premodified by two different methods priorto the polymer melt intercalation. In one case MMTs were modified with cetyltrimethylammonium bromide (CTAB), andtermed as organomontmorillonites (OMMTs); in the other case MMTs were modified by nylon, and the products were calledmodified montmorillonites (MMMTs). The effects of CTAB and nylon on the MMTs were investigated by using TG andWAXD. The results show that interlayer spacings of CTAN and nylon modified MMTs are larger than that of sodium MMTs.Then, polyamide 66 (PA 66)/MMT nanocomposites were obtained through the method of melt intercalation of polymers. Thenanocomposites were characterized by WAXD, TEM and Molau experiments. The results indicate that the MMTs dispersehomogeneously in the PA 66 matrix. The mechanical properties of nanocomposites, such as tensile properties and flexuralproperties, were also measured and show a tendency to increase with increase of MMT content and reach the maximumvalues at 5phr MMT content. The heat distortion temperature (HDT) of the nanocomposites (7 phr) is about 32 K higher thanthat of pure PA 66.     

Nonisothermal crystallization and morphology of poly(butylene succinate)/layered double hydroxide nanocomposites

Biodegradable poly(butylene succinate) (PBS) and layered double hydroxide (LDH) nanocomposites were prepared via melt blending in a twin-screw extruder. The morphology and dispersion of LDH nanoparticles within PBS matrix were characterized by transmission electron microscopy (TEM), which showed that LDH nanoparticles were found to be well distributed at the nanometer level. The nonisothermal crystallization behavior of nanocomposites was extensively studied using differential scanning calorimetry (DSC) technique at various cooling rates. The crystallization rate of PBS was accelerated by the addition of LDH due to its heterogeneous nucleation effect; however, the crystallization mechanism and crystal structure of PBS remained almost unchanged. In kinetics analysis of nonisothermal crystallization, the Ozawa approach failed to describe the crystallization behavior of PBS/LDH nanocomposites, whereas both the modified Avrami model and the Mo method well represented the crystallization behavior of nanocomposites. The effective activation energy was estimated as a function of the relative degree of crystallinity using the isoconversional analysis. The subsequent melting behavior of PBS and PBS/LDH nanocomposites was observed to be dependent on the cooling rate. The POM showed that the small and less perfect crystals were formed in nanocomposites.     

IN SITU OBSERVATION OF MELTING AND CRYSTALLIZATION BEHAVIORS OF POLY(ε-CAPROLACTONE) ULTRA-THIN FILMS BY AFM TECHNIQUE

The melting and crystallization behaviors of poly(ε-caprolactone) (PCL) ultra-thin films with thickness from 15 nm to 8 nm were studied by AFM technique equipped with a hot-stage in real-time. It was found that melting can erase the spherulitic structure for polymer film with high thickness. However, annealing above the melting point can not completely erase the tree-like structure for the thinner polymer film. Generally, the structure formation of thin polymer films of PCL is controlled not only by melting and crystallization but also by dewetting during thermal annealing procedures, and dewetting predominates in the structure formation of ultra-thin films. However, the presence of tree-like morphology at 75 °C may be due to the strong interaction between PCL and mica surface, which may stick the PCL chains onto the mica surface during thermal annealing process. Moreover, the growth of the dendrites was investigated and it was found that crystallization is followed from a dewetted sample, and the branches did not grow with the stems. The crystallization of polymer in the ultra-thin films is a diffusion-controlled process. Both melting and crystallization behaviors of PCL in thin films are influenced by film thickness.