高功率全光纤保偏主振荡功率放大型光纤激光器的实验研究

进行了全光纤保偏主振荡功率放大型光纤激光器的实验研究. 采用两级级联放大的方式, 利用纤芯为5 μupm 的小芯径双包层保偏光纤, 在最大抽运功率为88 W 时实现了67 W的1083 nm保偏激光输出, 纤芯内的激光功率密度约为3.4 W/μupm², 光-光转换效率为76%．分析结果表明, 进一步提高抽运功率有望获得更高功率的激光输出．     

Single-mode plane-polarized ytterbium-doped large-core fiber laser with 633-W continuous-wave output power

We demonstrate a cladding-pumped single-mode plane-polarized ytterbium-doped fiber laser generating 633 W of continuous-wave output power at 1.1 microm with 67% slope efficiency and a polarization extinction ratio better than 16 dB. The laser is end pumped through both fiber ends and shows no evidence of roll-over, even at the highest output power, which is limited only by the available pump power.     

Influence of fusion splice on high power ytterbium-doped fiber laser with master oscillator multi-stage power amplifiers structure

We have developed models to investigate the power properties of monolithic fiber laser with master oscillator multi-stage power amplifiers configuration. In the simulation the effect of optical characteristics of fiber fusion splice was considered, which was introduced by connecting fiber amplifiers. The theoretical modeling was established based on the classic theory of rate equations and the computational method was described in detail. On the basis of three high-power fiber lasers with different structures, we analyzed the splice loss and return loss, and how they influence the distribution of laser power in the system. The results showed that, on the present splicing level, both the enhancement of the pump capacity of fiber laser and the reduction of the quantity of power amplifier modules were effective strategies to accomplish fiber laser with tens of thousands of watts output.     

全光纤结构高功率主振荡功率放大型单频光纤激光器

研制了一台全光纤结构主振荡功率放大型掺镱单频光纤激光器。该光纤激光器包括种子激光器和级联放大器两部分。种子激光器是自行搭建的环形腔结构的单频窄线宽光纤激光器。在976 nm半导体激光器泵浦下,能够输出线宽为10 MHz量级、波长为1 079.88 nm的单频光,激光功率为10.02 W,光-光转化效率为58.9%,斜率效率为65.3%。     

Development of copper bromide laser master oscillator power amplifier system

Development of master oscillator power amplifier (MOPA) system of copper bromide laser (CBL) operating at 110 W average power is reported. The spectral distribution of power at green (510.6 nm) and yellow (578.2 nm) components in the output of a copper bromide laser is studied as a function of operating parameters. The electrical input power was varied from 2.6 to 4.3 kW, the pulse repetition frequency (PRF) was changed from 16 to 19 kHz, and the pressure of the buffer gas (neon) was kept fixed at 20 mbar. When the electrical input power was increased to 4.3 kW from 2.6 kW, the tube-wall temperature also increased to 488°C from 426°C but the ratio of the green to yellow power decreased to 1.53 from 3.73. The ratio of green to yellow power decreased to 1.53 from 1.63 when the PRF of the laser was increased to 19 kHz from 16 kHz. These observations are explained in terms of electron temperature, energy levels of transitions, and voltage and current waveforms across the laser head.     

High-power continuous-wave output of master oscillator power amplifier system at 1053 and 1083 nm

We report the efficient generation of high-power laser radiation at 1053 and 1083 nm wavelength by using of a hybrid master oscillator fiber power amplifier system, consisting of a diode-pumped Yb-doped oxyorthosilicate solid state laser as the master oscillator and an Yb-doped large-mode-area fiber as the power amplifier. Efficient tunable diode-pumped Yb-doped oxyorthosilicate lasers at 1053 and 1083 nm have been constructed, which was scaled up to a maximum output power of 34.5 W at 1053 nm and 30.2 W at 1083 nm by a fiber power amplifier, corresponding to a slope efficiency of 93.9 and 87.8%, respectively.     

10 W级主控振荡放大半导体激光芯片封装实验研究

结温升高是影响主控振荡放大(MOPA)半导体激光芯片输出功率的重要因素,为解决MOPA芯片的多电极封装和高效散热问题,提出了一种正装和热扩散辅助次热沉相结合的封装结构。建立了该封装结构的3D热模型,对比研究了倒装封装结构、正装无辅助次热沉结构与正装有辅助次热沉结构对MOPA半导体激光器结温的影响。计算结果表明,采用正装有辅助次热沉结构与倒装封装结构散热性能接近,且显著优于正装无辅助次热沉结构,结温降低幅度最高可达40%。另外,采用正装有辅助次热沉封装结构的MOPA半导体激光芯片在连续工作条件下输出功率为10.5 W,谱宽可实现半高全宽小于0.1 nm,中心波长随电流的变化约14 pm/A,实现了10 W级MOPA芯片的封装,验证了该封装结构的有效性。     

Single-frequency, single-mode, plane-polarized ytterbium-doped fiber master oscillator power amplifier source with 264 W of output power

We present a single-frequency, single-mode, plane-polarized ytterbium-doped all-fiber master oscillator power amplifier source at 1060 nm generating 264 W of continuous-wave output power. The final-stage amplifier operated with a high gain of 19 dB and a high conversion efficiency of 68%. There was no evidence of rollover from stimulated Brillouin scattering even at the highest output power, and the maximum output was limited only by the available pump power.     

High-power Tm~(3+)-doped all-fiber laser operating at1908 nm by a master oscillator power amplifier configuration with narrow spectral linewidth

We demonstrate a diode-pump Tm~(3+)t-doped all-fiber laser operating at 1908 nm based on a master oscillator power amplifier(MOPA) configuration. In our work, 152 W of laser output power is generated by a total incident pump power of 434 W at 790 nm, corresponding to the total optical efficiency of 35%. The laser wavelength is1908.29 nm. To the best of our knowledge, it is the highest output power reached around 1908 nm with such a narrow linewidth of 0.18 nm based on a MOPA configuration.     

90.4-W all-fiber single-frequency polarization-maintained 1083-nm MOPA laser employing ring-cavity single-frequency seed oscillator

A high-power all-fiber single-frequency polarization-maintained（PM）laser operating at 1 083 nm is demonstrated using a master oscillator power amplifier（MOPA）structure.The seed source of this MOPA laser system is an in-house-built ring-cavity fiber oscillator.Four-stage amplification configuration is employed, in which the maximal output power of the main amplifier is 90.4 W,corresponding to a conversion efficiency of 72.5%.The polarization extinction ratio of the output light is 13 dB.The amplified spontaneous emission is suppressed by a factor of over 25 dB,and no stimulated Brillouin scattering effect is observed when a large-mode-area and high absorption coefficient PM gain fiber is employed.     

侧面泵浦主振荡功率放大器中的光束质量提高

报道了一种利用球差补偿效应提高侧面泵浦主振荡功率放大器输出光束质量的实验装置。在理论上提出了一种新的球差补偿方法,利用正球差经过会聚透镜焦点后向负球差转化的现象,补偿下一放大级中的正球差效应。在实验上搭建了两级放大的侧面泵浦Nd:YAG主振荡功率放大器。在连续输出的情况下,从振荡级输出功率为42W、光束质量因子为1.48的种子光,经过一级放大后的功率为74W,光束质量因子恶化为1.80;继续经过二级放大后,光束质量因子提高为1.40。实验结果表明,所提出的球差补偿理论是提高激光放大过程中光束质量的有效手段。     

侧面泵浦主振荡功率放大器中的光束质量提高

报道了一种利用球差补偿效应提高侧面泵浦主振荡功率放大器输出光束质量的实验装置。在理论上提出了一种新的球差补偿方法,利用正球差经过会聚透镜焦点后向负球差转化的现象,补偿下一放大级中的正球差效应。在实验上搭建了两级放大的侧面泵浦Nd:YAG主振荡功率放大器。在连续输出的情况下,从振荡级输出功率为42 W、光束质量因子为1.48的种子光,经过一级放大后的功率为74 W,光束质量因子恶化为1.80;继续经过二级放大后,光束质量因子提高为1.40。实验结果表明,所提出的球差补偿理论是提高激光放大过程中光束质量的有效手段。     

Laser-diode-pumped zigzag slab Nd:YAG master oscillator power amplifier

A high-repetition rate master oscillator power amplifier pumped with laser diodes (LDs) is reported. An injection seeding single-frequency electro-optical Q-switched Nd:YAG laser is used as an oscillator, and a conductively cooled Nd:YAG zigzag slab with a bounce-pumped architecture is utilized as a power amplifier. Pulse energies of over 800 mJ at 1 064 nm and 400 mJ at 532 nm, corresponding to average powers of 200 and 100 W, respectively, are achieved with a 12.6-ns pulse width at 250 Hz. Output frequency fluctuations and single-frequency operation are further monitored. Experimental results reveal that the proposed system, which features a single-pass amplified configuration, is a promising design for space-based applications.     

High-average-power (15-W) 255-nm source based on second-harmonic generation of a copper laser master oscillator power amplifier system in cesium lithium borate

We have generated 15 W of UV (255-nm) radiation with an optical conversion efficiency of 28% by frequency doubling the 510.6-nm output of a high-beam-quality, high-power copper laser system in cesium borate lithium (CLBO). We found that the superior performance of CLBO relative to beta-barium borate is attributable largely to the small UV absorption and wide temperature acceptance bandwidth of CLBO, which reduces thermal dephasing during high-power UV generation.     

高功率全光纤结构主振荡功率放大器中模式不稳定现象的实验研究

模式不稳定指高功率光纤激光随着输出功率提升发生的模式突变,会导致光束质量下降,限制了衍射极限光束质量光纤激光输出功率的提升,本文研究了全光纤结构主振荡功率放大器中的模式不稳定现象,结果表明,全光纤结构主振荡功率放大器中的模式不稳定现象会导致放大器斜率效率下降;理论计算表明,对于20/400阶跃折射率大模场双包层掺镱光纤,注入种子功率在百瓦左右时,模式不稳定发生的阈值功率在1kW左右:热效应是模式不稳定现象发生的根源。     

26W near diffraction limited Q-switched green laser based on a diode-end-pumped master oscillator power amplifier

An efficient acousto-optically Q-switched extracavity frequency-doubled 532nm laser based on a diode-end-pumped master oscillator power amplifier (MOPA) is demonstrated. With a type I non-critically phase-matched LBO, 26W of average power at 532nm in a near diffraction limited mode at a repetition rate of 30kHz was generated under 43W pump power of 1064nm Nd:YVO_{4} laser, which correspond to a frequency-doubling conversion efficiency of 60%.     

2277-W continuous-wave diode-pumped heat capacity laser

A high power continuous-wave (CW) diode-pumped Nd:YAG laser operated in heat capacity mode is demonstrated by use of two identical highly efficient diode-pumped laser heads placed in a plane-plane resonator. The laser heads are uniformly pumped with a five-fold symmetrical side-pumping configuration,and each head is able to output maximum output power of 2200 W at 808 nm. Under a total pump power of 4290 W, the output power of the laser at 1064 nm is up to 2277 W, corresponding to an optical-to-optical efficiency of 53.1%.     

A 168-W high-power single-frequency amplifier in an all-fiber configuration

We present a high-power,single-frequency,narrow linewidth fiber amplifier based on master oscillator power amplification chains in an all-fiber configuration.The effect of the delivery fiber on the maximum output power is studied.A home-made 1064-nm seed laser with a 20-kHz linewidth is boosted to 129 W,and limited by stimulated Brillouin scattering(SBS) when the delivery fiber is 1.2 m long.By shortening the delivery fiber length to 0.7 m,the SBS threshold is increased efficiently and the maximum output power rises to 168 W with an 82.9% power conversion efficiency.The experimental results indicate that the output power can be further raised by shortening the delivery fiber length and increasing the pump power.     

A 168-W high-power single-frequency amplifier in an all-fiber configuration

We present a high-power, single-frequency, narrow linewidth fiber amplifier based on master oscillator power amplification chains in an all-fiber configuration. The effect of the delivery fiber on the maximum output power is studied. A home-made 1064-nm seed laser with a 20-kHz linewidth is boosted to 129 W, and limited by stimulated Brillouin scattering (SBS) when the delivery fiber is 1.2 m long. By shortening the delivery fiber length to 0.7 m, the SBS threshold is increased efficiently and the maximum output power rises to 168 W with an 82.9% power conversion efficiency. The experimental results indicate that the output power can be further raised by shortening the delivery fiber length and increasing the pump power.     

Switchable mode-locking states in an all-fiber all-normal-dispersion ytterbium-doped laser

Multi-operation state in an all-normal-dispersion ytterbium-doped fiber laser is obtained by introducing nonlinear polarization or hybrid mode-locking mechanism in the laser cavity. In addition to operating the laser at continuous-wave mode-locking, various operation states including continuous-wave, Q-switched mode-locking, pulse-splitting, and harmonic mode-locking can be achieved by tuning the laser pump power or an intracavity polarization controller. Insertion of a semiconductor saturable absorber mirror in the cavity helps to shorten the output pulsewidth of the hybrid mode-locked laser. When the pump power is rapidly adjusted, a strong asymmetric hysteresis behavior can be observed during the manipulation between different orders of harmonic mode-locking.