聚苯乙烯/Ag核壳结构纳米微粒的制备及表征

用种子乳液聚合法合成了聚苯乙烯（PS）/Ag复合纳米粒子,进一步利用分步聚合技术实现了聚甲基丙烯酸甲酯(PMMA)在微球表面功能化,分别用TEM、XRD、TG-DTA及FT-IR对其结构和形貌进行了表征,并考察了其摩擦学性能.结果表明,在所选择的实验条件下,合成了以Ag纳米微粒为核,PS、PMMA为壳层的核壳结构复合纳米微球,其中Ag纳米核平均粒径约12 nm,复合微球粒径约25 nm,颗粒较均匀并且在有机溶剂中有良好的分散性,作为润滑油添加剂,具有良好的抗磨性能.     

聚甲基丙烯酸甲酯/聚甲基丙烯酸-2-羟乙酯复合微球的合成及药物吸放性能

采用在甲基丙烯酸甲酯（MMA）悬浮聚合过程中滴加甲基丙烯酸-2-羟乙酯（HEMA）乳液聚合组分的悬浮-乳液耦合聚合方法,制备了大粒径聚甲基丙烯酸甲酯／聚甲基丙烯酸-2-羟乙酯（PMMA／PHEMA）复合微球。PMMA／PHEMA复合微球表面以HEMA乳液聚合物为主,且具有微孔结构。PMMA／PHEMA复合微球在水和苄醇中的平衡溶胀率大于PMMA微球。PMMA／PHEMA复合微球48h异丁苯丙酸负载百分比为35．6％,PMMA为27．6％。在磷酸盐缓冲液中释放时间达到360h,释放量占负载总量的82％;而PMMA微球的释放时间为216h,释放量仅占负载总量的60％。     

PMMA纳米球的制备及其银膜包覆技术

采用无皂乳液聚合法制备了单分散、直径为170 nm左右的聚甲基丙烯酸甲酯(PMMA)纳米球, 然后利用3-甲基丙烯酰氧基丙基三甲氧基硅烷(MATS)和3-巯丙基三甲氧基硅烷(MPTMS)对PMMA纳米球进行表面改性, 在其表面包覆一层均匀的巯基, 通过巯基与银离子之间的相互作用, 使银在PMMA纳米球表面成核长大, 从而合成PMMA/Ag纳米球壳粒子. 通过扫描电子显微镜、投射电子显微镜和紫外-可见吸收光谱测试技术对产物性能进行了表征, 研究结果表明, 制备的PMMA/Ag纳米球壳粒子的分散性好、包覆均匀.     

Poly(methyl methacrylate)/multiwalled carbon nanotube microspheres fabricated via in‐situ dispersion polymerization

Poly(methyl methacrylate)/multiwalled carbon nanotube (PMMA/MWCNT) microspheres were successfully prepared by in situ dispersion polymerization in an alcohol phase in which the acid‐treated MWCNTs were dispersed before polymerization. The PMMA and PMMA/MWCNT microspheres were monodisperse. The diameters of the microspheres decreased from about 11.6–6.0 μm as the MWCNT content was increased from 0 to 0.03 wt %. The morphology of the PMMA/MWCNT microspheres was investigated by scanning electron microscopy, atomic force microscopy, and transmission electron microscopy, and the experimental results showed that the MWCNTs were present both in the interior and on the surface of the microspheres. The synthesized PMMA/MWCNT microspheres were also characterized by electrical resistance measurements to analyze their electrical conductivity. They showed electrorheological (ER) fluid characteristics when they were dispersed in silicone oil. Their ER properties were confirmed by using optical microscopy to examine a suspension of the PMMA/MWCNT microspheres dispersed in insulating silicone oil to which an electric field of 2.5 kV/cm was applied. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 182–189, 2008     

Cellulose/silver nanoparticles composite microspheres: eco-friendly synthesis and catalytic application

Cellulose/silver nanoparticles (Ag NPs) composites were prepared and their catalytic performance was evaluated. Porous cellulose microspheres, fabricated from NaOH/thiourea aqueous solution by a sol–gel transition processing, were served as supports for Ag NPs synthesis by an eco-friendly hydrothermal method. The regenerated cellulose microspheres were designed as reducing reagent for hydrothermal reduction and also micro-reactors for controlling growth of Ag NPs. The structure and properties of obtained composite microspheres were characterized by Optical microscopy, UV–visible spectroscopy, WXRD, SEM, TEM and TG. The results indicated that Ag NPs were integrated successfully and dispersed uniformly in the cellulose matrix. Their size (8.3–18.6?nm), size distribution (3.4–7.7?nm), and content (1.1–4.9?wt%) were tunable by tailoring of the initial concentration of AgNO₃. Moreover, the shape, integrity and thermal stability were firmly preserved for the obtained composite microspheres. The catalytic performance of the as-prepared cellulose/Ag composite microspheres was examined through a model reaction of 4-nitrophenol reduction in the presence of NaBH₄. The composites microspheres exhibited good catalytic activity, which is much high than that of hydrogel/Ag NPs composites and comparable with polymer core–shell particles loading Ag NPs.     

Multihollow structured poly(methyl methacrylate)/silver nanocomposite microspheres prepared by suspension polymerization in the presence of dual dispersion agents

Poly(methyl methacrylate) (PMMA)/silver nanocomposite microspheres with unique multihollow structures were prepared by suspension polymerization in the presence of dual dispersion agents. The addition of a lipophilic emulsifier, polyethylene glycol (30EO) dipolyhydroxystearate (Arlacel P135), not only stabilized water-in-oil (W/O) emulsion, but also converted silver nanoparticles from hydrophilic to lipophilic. When a suspension polymerization dispersion agent, poly(vinyl alcohol), was added to the above W/O emulsion system, a water-in-oil-in-water suspension was formed with silver nanoparticles dispersed in the oil phase. The suspension polymerization was carried out at low temperature with 2,2’-azobis(2,4-dimethylvaleronitrile) as the initiator. When modified silver nanoparticles were added, the rate of polymerization increased slightly. High monomer conversion (about 85%) was obtained in spite of low polymerization temperature of 30 °C. Under controlled conditions, PMMA/silver microspheres with various hollow structures were synthesized. The PMMA/silver microspheres with multihollow structure showed high antibacterial ability.     

In situ formation of silver nanoparticles in PMMA via reduction of silver ions by butylated hydroxytoluene

Silver nanoparticles (Ag NPs) were efficiently generated by in situ reduction of silver ions via butylated hydroxytoluene (BHT), in poly(methyl methacrylate). The characterization of Ag/PMMA by TEM, SEM, XRD, and FTIR indicated that Ag NPs with a face center cubic (fcc) crystal structure and a mean diameter of about 30 nm were dispersed in PMMA matrix with a relatively uniform distribution. In addition, the results of UV–Vis spectroscopy indicated that optical properties of the nanocomposite appeared mainly dependent on the reaction time and temperature. Increasing the reaction time and temperature make higher yield of Ag NPs. A provisional reduction mechanism was also proposed for the formation of the Ag NPs.     

复合Ag/ZnO分级结构微球的制备及其光催化性能研究

采用化学沉淀法制备ZnO微球,利用柠檬酸三钠（TCD）避光还原硝酸银在ZnO表面沉积银粒子制备Ag/ZnO复合材料.利用XRD、SEM、TEM、EDS、FTIR、UV-vis DRS、PL、BET等对Ag/ZnO的结构、组分、形貌及光谱性质进行了表征,通过紫外及可见光照降解甲基橙溶液评价样品的光催化性能.结果表明：ZnO纳米微球是由ZnO纳米片相互交错构筑而成的具有丰富孔道的分级结构,Ag纳米粒子均匀沉积在ZnO纳米片上.Ag的沉积显著增加了ZnO的可见光吸收,猝灭了ZnO荧光,提高了ZnO催化活性.     

Titanium dioxide/poly(methyl methacrylate) composite microspheres prepared by in situ suspension polymerization and their ability to protect against UV rays

Homogenously dispersed TiO₂/poly(methyl methacrylate) (PMMA) composite microspheres were produced in the size range of 1-10µm and the interfacial characteristics of TiO₂ and PMMA in suspension polymerization were considered. In electron microscopy observation, it was found that TiO₂ nanoparticles were embedded homogeneously in the PMMA phase. This study elucidates that the interfacial compatibility between TiO₂ and PMMA played a decisive role in producing the composite microspheres structured with inner TiO₂ and continuous PMMA, which was achieved by treating the surface of the TiO₂ particles hydrophobically. The TiO₂/PMMA composite microspheres produced showed good ability to protect against UV rays and are therefore of great usefulness in cosmetic formulations.     

流动控制沉积法制备PMMA叠层光子晶体薄膜及其光学性能研究

采用流动控制沉积法,通过调控泵速和聚甲基丙烯酸甲酯(PMMA)胶体微球溶液的浓度,制备出微球排列高度有序且薄膜紧密附着于基底的高质量光子晶体薄膜。获得了制备高质量PMMA光子晶体薄膜的组装条件范围,发现在该条件范围内,当泵速或胶体微球溶液浓度一定时,PMMA光子晶体薄膜的厚度随胶体微球溶液浓度的增加或泵速的降低而增加。研究了组装条件对PMMA光子晶体薄膜光学性能的影响,发现光子禁带位置随光子晶体薄膜厚度增加或减少而红移或蓝移。在此基础上,控制组装条件得到了不同尺寸微球堆叠而成的叠层光子晶体薄膜,并研究了其光学性能的变化规律。结果显示,叠层光子晶体薄膜的光子禁带峰为各层叠层光子晶体禁带峰的简单叠加,且峰强度受光入射角方向影响。     

One pot synthesis of Ag nanoparticle modified ZnO microspheres in ethylene glycol medium and their enhanced photocatalytic performance

Ag nanoparticles (NPs) modified ZnO microspheres (Ag/ZnO microspheres) were prepared by a facile one pot strategy in ethylene glycol (EG) medium. The EG played two important roles in the synthesis: it could act as a reaction media for the formation of ZnO and reduce Ag⁺ to Ag⁰. A series of the characterizations indicated the successful combination of Ag NPs with ZnO microspheres. It was shown that Ag modification could greatly enhance the photocatalytic efficiency of ZnO microspheres by taking the photodegradation of Rhodamine B as a model reaction. With appropriate ratio of Ag and ZnO, Ag/ZnO microspheres showed the better photocatalytic performance than commercial Degussa P-25 TiO₂. Photoluminescence and surface photovoltage spectra demonstrated that Ag modification could effectively inhibit the recombination of the photoinduced electron and holes of ZnO. This is responsible for the higher photocatalytic activity of Ag/ZnO composites.     

负载纳米银复合微球制备及其催化性能

以具有温度和pH双重敏感性能的N-异丙基丙烯酰胺(NIPAM)共聚丙烯酸(AA) P(NIPAM-co-AA)高分子微凝胶为模板, 以乙醇为还原剂, 原位还原得到负载纳米银的微米尺度Ag/P(NIPAM-co-AA)复合微凝胶材料. 通过扫描电子显微镜(SEM)、X射线衍射(XRD)仪和紫外-可见(UV-Vis)分光光度计等对复合材料的形貌、组成和催化性能进行表征. 研究结果表明, Ag/P(NIPAM-co-AA)复合微球具有均一的表面结构, 微凝胶的限域作用显著提高了纳米银的分散性和稳定性. 另外, Ag/P(NIPAM-co-AA)复合微球对对硝基苯酚(4-NP)的还原具有较好的催化活性, 且其催化活性与微凝胶网络结构的溶胀、收缩行为有一定关系, 即模板微凝胶的温敏特性可以实现对对硝基苯酚催化反应活性的调控作用.     

Polyaniline microsphere encapsulated by poly(methyl methacrylate) and investigation of its electrorheological properties

Microspheres consisting of a poly(methyl methacrylate) (PMMA) shell wrapping the conductive polyaniline (PANI) particle as a core were prepared by an in-situ suspension polymerization method and then adopted as an electrorheological (ER) material. The polymerization reaction and encapsulation were confirmed by Fourier transform infrared spectrum analysis. The rod-like PANI particles were synthesized via an emulsion polymerization protocol and observed by transmission electron microscopy. In addition, a spherical shape of encapsulated PANI/PMMA (core/shell) microspheres was observed by scanning electron microscopy. The thermal stability of PANI/PMMA particles was examined by use of thermogravimetric analysis. The PANI/PMMA particle-based suspension in silicone oil exhibited typical ER behavior. The conductivity of PANI/PMMA particles was much lower than that of the rod-like PANI.     

草莓型PMMA/SiO2有机-无机复合微球的合成与表征

在纳米二氧化硅水分散介质中,借助于正离子单体甲基丙烯酰氧乙基三甲基氯化铵(MTC)与未改性纳米二氧化硅颗粒之间的电荷作用,通过MTC与甲基丙烯酸甲酯(MMA)的自由基共聚合,制备了草莓型的PMMA/SiO2复合微球.整个制备反应过程中,纳米二氧化硅无需表面处理,体系中无需另外加入乳化剂或助乳化剂,微球表面吸附的纳米二氧化硅对颗粒起稳定作用.详细讨论了纳米二氧化硅初始添加量、MTC浓度对复合微球的平均粒径、复合微球中二氧化硅含量及微球形态的影响.动态光散射粒度分布仪(DLS)测得复合微球粒径在180~300 nm之间,热重分析(TGA)表明复合微球中二氧化硅含量介于16.4%~40.8%之间.透射电镜(TEM)显示所得复合微球具有草莓型结构,二氧化硅于表面富集.     

ZnO/Ag微米球的合成与光催化性能

用微波辅助多元醇法对预先制备的ZnO微米球进行修饰,合成了载银氧化锌微米球（ZnO/Ag）. 利用X射线衍射仪、场发射扫描电子显微镜、透射电子显微镜、X射线光电子能谱仪、紫外-可见双光束分光光度计和光致发光光谱仪等对样品的结构、形貌和光学性能进行了表征. 在紫外光照射下,通过亚甲基蓝的降解反应研究了样品的光催化活性. 结果表明,所制备的ZnO/Ag微米球是由面心立方的Ag纳米颗粒附着在纤锌矿结构的ZnO球表面形成;与ZnO相比,ZnO/Ag的紫外-可见光吸收光谱发生明显红移,在紫外和可见光范围均有较强的吸收;随着Ag含量的增加,ZnO/Ag荧光光谱强度先减弱后增强;与ZnO相比,ZnO/Ag的光催化活性明显提高,AgNO₃ 浓度为0.05 mol/L时制得的ZnO/Ag光催化活性最高.     

Ag/mSiO2空心微球的制备及SERS标记性能

以聚苯乙烯微球为模板, 经过原位还原和种子生长过程在聚苯乙烯微球表面包覆银(Ag)纳米粒子; 以正硅酸乙酯为硅源, 在十六烷基三甲基溴化铵的导向下实现介孔二氧化硅(mSiO₂)可控包覆, 去除模板得到Ag/mSiO₂空心微球. 透射电子显微镜(TEM)和氮气吸附-脱附分析结果表明, SiO₂壳层厚度约为20 nm, 介孔孔径为2.1 nm, 孔道分布均匀. 进一步利用虹吸作用使对巯基苯胺(4-ATP)分子进入微球内与Ag粒子结合, 构建表面增强拉曼散射(SERS)标记材料. SERS测试结果表明, 该标记材料检测限达到10^-7 mol/L, SERS增强因子达到3.7×10⁵.     

不同尺寸单分散PMMA/GMA/DVB聚合物荧光微球的制备

采用无皂乳液聚合及种子无皂乳液聚合方法制备了200～800 nm四种不同尺寸的单分散PMMA/GMA/DVB (PMGD)复合微球. 用扫描电镜(SEM)和动态光散射(DLS)对粒径尺寸、形貌进行了表征. 实验发现单体滴加速度是影响种子无皂乳液聚合过程二次成核的关键因素. 用乙二胺对微球表面的环氧基团开环后, 通过在微球表面接枝树枝状PAMAM (d-PAMAM)达到微球表面的官能化的目的, 元素分析和红外光谱实验证明了微球表面d-PAMAM的存在. 最后利用微球表面的活性氨基与四甲基异硫氰酸罗丹明(TRITC)反应, 得到四种尺寸的水分散性的红色荧光微球.     

二硫化锡纳米片阻变存储器的制备与性能

采用水热法合成了尺寸为50~100 nm的二硫化锡纳米片,并首次以二硫化锡作为阻变层材料的阻变存储器（Cu/PMMA/SnS₂/Ag,PMMA=聚甲基丙烯酸甲酯）,对其阻变性能进行了研究。结果表明： Cu/PMMA/SnS₂/Ag阻变存储器的开关比约10⁵,耐受性2.7×10³。在上述2项性能指标达到较优水平的同时,开态与关态电压分别仅约为0.28与-0.19 V。     

Ag负载TiO2核壳基底的制备及对结晶紫的高效(SERS)检测

通过简单的一步水热法制备了TiO2核壳微球,然后经过原位光还原将Ag负载于其表面,成功得到了用于有机分子检测的Ag负载TiO2核壳表面增强拉曼散射（SERS）基底。得益于TiO2核壳微球的结构,其对结晶紫（CV）分子表现出高的吸附容量。单一TiO2核壳微球对CV的检测限为10-3 M,而负载Ag以后,其对CV的检测限能达到10-7 M,增强因子（EF）可达3.49×105。优异的SERS检测性能可能归因于以下几点：（1）半导体TiO2为Ag纳米粒子提供了均匀分散的骨架,创造了高密度的热点;（2）为CV分子提供了大的吸附面积;（3）复合材料促进了激发光子的相互作用。     

Plasmon-resonance-enhanced visible-light photocatalytic activity of Ag quantum dots/TiO2 microspheres for methyl orange degradation

We successfully prepared Ag quantum dots modified TiO₂ microspheres by facile solvothermal and calcination method. The as-prepared Ag quantum dots/TiO₂ microspheres were characterized by scanning electron microscope, transmission electron microscope, X-ray diffraction, X-ray photoelectron spectroscopy and UV-vis diffuse reflectance spectroscopy. The Ag quantum dots/TiO₂ photocatalyst showed excellent visible light absorption and efficient photocatalytic activity for methyl orange degradation. And the sample with the molar ratio of 0.05 (Ag to Ti) showed the best visible light photocatalytic activity for methyl orange degradation, mainly because of the surface plasmon resonance (SPR) effects of Ag quantum dots to generate electron and hole pairs for enhanced visible light photocatalysis. Finally, possible visible light photocatalytic mechanism of Ag quantum dots/TiO₂ microspheres for methyl orange degradation was proposed in detail.