Copper Promoted Au/ZnO-CuO Catalysts for Low Temperature Water-gas Shift Reaction

IntroductionThe water-gas shift(WGS)reaction is an impor-tant step in many important chemical processes[1].Re-cently,the renewed interest in the removal of CO bythe WGS reaction has grown significantly because of theincreasing attention to pure hydrogen p…     

Kinetics of hydrogen production of methanol reformation using Cu/ZnO/Al2O3 catalyst

The catalytic performance of methanol reformation using Cu/ZnO/Al2O3 was investigated at low temperature. The operation conditions, such as composition of Cu, Zn, and Al, temperature, molar ratio of H2O/CH3OH, weight hourly space velocity, catalyst weight, and kind and flow rate of carrier gas (helium and air), were evaluated to obtain the optimum reaction condition. The catalysts were prepared by oxalic coprecipitation, coprecipitation, and polyol method. The weight composition of Cu, Zn, and Al prepared by oxalic coprecipitation was 15:15:5 by high-throughput screening of combinatorial chemistry method, which was the best Cu/ZnO/Al2O3 catalyst. The prepared catalysts showed high activity and selectivity towards hydrogen formation. The methanol conversion, production rate, and volumetric percentage of hydrogen using this best catalyst were larger than 95%, 0.65 mol/h x g and 59%, respectively, and the CO volumetric percentage was smaller than 0.22% when the reaction temperature was 240 degrees C. The size and dispersity of copper, and the activity and turnover frequency of the catalyst were calculated as well.     

AHTD法铜基催化剂合成甲醇的研究——Ⅰ.催化剂的催化性能

自从ICI低压、低温甲醇合成过程取代高压过程以来,人们对该过程所使用的Cu/ZnO/Al_2O_3或Cu/ZnO/Cr_2O_3催化剂有极大的兴趣。Herman、Klier等人已证明这种低压、低温下的活性应归属于Cu-ZnO间的相互作用,在相同的条件下,单纯的铜或氧化锌的活性几乎可以忽略不计,而氧化铝或氧化铬主要起结构助剂的作用。由此可见,控制适宜的Cu-ZnO间的相互作用是提高甲醇合成活性的关键,因此,如何才能产生这种适宜的相互作用就成了人们极为重视的研究课题。到目前为止,人们普遍采用沉淀法制备铜基甲醇合成催化剂,试图通过改变各种制备条件来开发更好的     

Cu/ZnO@H-β-P催化剂在合成气制备液化石油气反应中的性能研究

采用共沉淀法制备Cu/ZnO催化剂、水热合成法制备H-β分子筛、通过物理包膜法制备了具有核壳结构的Cu/ZnO@H-β-P催化剂,并用于合成气制备液化石油气(LPG)反应。通过XRD、NH3-TPD、BET和SEM-EDS等手段对催化剂进行了表征,利用固定床连续反应装置对催化剂进行了活性评价。结果表明,Cu/ZnO@H-β-P催化剂是具有中孔的核壳结构材料,其协同作用打破了原有的热力学平衡,促进了甲醇→DME→LPG串联反应的连续进行。与物理混合的Mix-Cu/ZnO-H-β催化剂相比,Cu/ZnO@H-β-P催化剂的CO转化率和LPG选择性更高,空速和反应温度对催化剂活性影响明显,最佳空速和反应温度分别为2 400 h~(-1)和350℃。使用Cu/ZnO@H-β-P催化剂在最佳条件下进行合成气制备LPG反应,CO转化率达到了57.22%,LPG选择性达到了60.52%。     

尿素燃烧法制备CuO-ZnO/HZSM-5及其催化CO_2加氢合成二甲醚的性能

以尿素为燃烧剂,先采用燃烧法制备CuO-ZnO催化剂,接着采用研磨法将其与HZSM-5分子筛均匀混合形成CuO-ZnO/HZSM-5双功能催化剂.采用固定床反应器,在反应温度260℃、压力3.0 MPa、空速1 500 h-1条件下,考察了不同Cu/Zn(摩尔比)催化剂在CO_2加氢合成二甲醚反应中的催化性能.通过XRD、N_2等温吸附脱附、H2-TPR、NH3-TPD对催化剂进行表征,研究了不同Cu/Zn对催化剂结构及表面酸性的影响.结果表明:当Cu∶Z n=6∶4时,催化剂对CO_2催化加氢直接合成二甲醚反应的催化活性和选择性最佳,CO_2的转化率、DME的选择性分别为11.95%和28.74%,且在催化剂上具有更多的低温还原Cu和较强的酸中心,从而提高了CO_2加氢活性和二甲醚的选择性.     

Ce的浸渍顺序对Cu/Zn-Al水滑石衍生催化剂用于甲醇水蒸气重整制氢性能的影响

采用原位合成法在γ-Al_2O_3载体上合成了锌铝水滑石,再经浸渍法制备了Cu/Zn-Al、Ce/Cu/Zn-Al、Cu/Ce/Zn-Al和Cu-Ce/Zn-Al催化材料,使用XRD、XRF、SEM、氮吸附,XPS、H_2-TPR和N_2O滴定等手段对其进行了表征,探讨了Ce的浸渍顺序对Cu/Zn-Al水滑石衍生材料甲醇水蒸气重整制氢反应催化性能的影响。结果表明,Ce的浸渍顺序主要影响催化剂的还原性质,进而影响了其催化性能。其中,Ce/Cu/Zn-Al催化剂的催化性能最佳,在250℃、水醇物质的量比为1.2、甲醇气体空速为800 h~(-1)的条件下,甲醇转化率达到100%;与Cu/Zn-Al催化剂相比,甲醇转化率提高了近40%。     

铈源对甲醇水蒸气重整制氢CuO/CeO2催化剂的影响

采用沉淀法合成了CeO_2载体,再经浸渍法负载活性组分得到CuO/CeO_2催化材料,探究了铈源(Ce(NO_3)_3·6H_2O、Ce Cl_3·6H_2O、Ce(NH_4)_2(NO_3)_6、Ce(SO_4)_2·4H_2O)对CuO/CeO_2催化性能的影响。通过采用XRD、SEM、N_2O滴定、BET和H_2-TPR等表征手段对催化材料的结构和性质研究发现,四种铈源合成的CuO/CeO_2催化材料在Cu比表面积、还原性能以及活性组分和载体间的相互作用方面存在着明显差别。其中,由Ce(NO_3)_3·6H_2O合成的CuO/CeO_2催化材料的Cu比表面积较大,CuO还原温度较低,CeO_2载体与CuO之间相互作用较强,在甲醇水蒸气重整反应过程中,表现出较佳的催化活性,在反应温度为553 K,水醇比n(H_2O)/n(MeOH)为1.2,甲醇水蒸气气体空速(GHSV)为1760 h~(-1)时,甲醇的转化率为100%,重整气中CO摩尔含量为0.84%。     

甲醇水蒸气重整制氢Cu/ZnO/Al2O3催化剂的研究

燃料电池作为一种无污染、高效率的能源引起世界各大汽车公司的广泛关注[1,2]。用于燃料电池的燃料目前研究较多的是氢气,用氢气作燃料存在储存、安全、运输等问题,寻求合适贮氢方法或替代燃料,实现车载制氢是解决问题的办法。甲醇作为液体燃料,因具有高能量密度,低碳含量,以及运输和贮存等优势成为车载制氢的理想燃料,甲醇水蒸气重整制氢反应也成为研究的热点[3～10]。车载制氢对甲醇水蒸气重整制氢反应体系中的产氢速率,氢气和CO的含量都有一定的要求。尤其对CO含量要求更为苛刻,因CO易引起燃料电池阳极催化剂中毒[11,12]。因此,开…     

膜反应器中Ni-Cu催化剂上CO加氢合成乙烯的研究

 将硅藻土－TiO2－聚乙烯（或聚丙烯）疏水复合膜反应器应用于\r\nCO加氢合成乙烯的反应过程，以Ni－Cu／TiSiO和Ni－Cu／MgSiO为催化\r\n剂，考察了反应温度、空速和进料组成等因素对CO转化率和乙烯选择性\r\n的影响．结果表明：膜催化反应的产物与常规催化反应相同，催化反应\r\n机理没有区别，在适宜条件下，膜催化反应的CO转化率和乙烯选择性较\r\n之常规催化反应提高了10％左右，二氧化碳和甲烷的选择性降低，而乙\r\n烷的选择性略有增加．     

Kinetics of the water-gas shift reaction in Fischer-Tropsch synthesis over a nano-structured iron catalyst

Based on formate and direct oxidation mechanisms, three Langmuir-Hinshelwood-Hougen-Watson (LHHW) kinetic models of the water-gasshift (WGS) reaction over a nano-structured iron catalyst under Fischer-Tropsch synthesis (FTS) reaction conditions were derived and compared with those over the conventional catalyst. The conventional and nanostructured Fe/Cu/La/Si catalysts were prepared by co-precipitation of Fe and Cu nitrates in aqueous media and water-oil micro-emulsion, respectively. The WGS kinetic data were measured by experiments over a wide range of reaction conditions and comparisons were also made for various rate equations. WGS rate expressions based on the formate mechanism with the assumption that the formation of formate is rate determining step were found to be the best.     

Stabilization of Cu/ZnO Based Catalysts by Nickel Additive in Methanol Decomposition

A series of Cu/Zn based catalysts with and without Ni, prepared by the co-precipitation method, has been studied for methanol decomposition. CO and H2 are the major products. The Cu/Zn catalysts show a low initial activity and a poor stability. The formation of the CuZn alloys was observed in the deactivated Cu/Zn catalysts which were used for methanol decomposition at 250 . When small amounts of Ni were added in the catalyst, the Cu/Zn/Ni(molar ratio 5/4/ x) catalysts showed a high activity at a low temperature. The activity and the stability of the catalyst depend on the nickel content. The activity of the Cu/Zn/Ni catalysts was maintained at a. relatively stable value of 78% conversion of methanol with 95% selectivity of H2, 93% selectivity of CO, and a more than 70% yield of hydrogen was obtained at 250 C when x >1. The stability of the Cu/Zn/Ni (molar ratio 5/4/x) catalysts showed the maximum (ca 88%) when x=1. The stabilization effect of nickel on the Cu/Zn based catalysts may lead to the increasin     

结构助剂SiO2、Al2O3对铁基催化剂浆态床F-T合成性能的影响

采用连续共沉淀与喷雾干燥成型技术相结合的方法制备了微球状Fe/Cu/K/SiO2和Fe/Cu/K/Al2O3催化剂,研究SiO2和Al2O3作为结构助剂对铁基催化剂吸附行为、炭化行为及F-T合成反应性能的影响。表征结果表明,与Al2O3相比较,SiO2抑制了H2的吸附,但促进了CO的吸附,有利于催化剂的炭化。催化剂在260℃、1.5MPa、H2/CO=0.67和2000h-1下的浆态床F-T合成反应评价表明,Fe/Cu/K/SiO2催化剂具有较高的F-T合成活性、高的水煤气变换反应（WGS）活性,且其烃产物选择性明显向高炭数方向偏移,而Fe/Cu/K/Al2O3催化剂则表现出较低的F-T合成活性、低的水煤气变换反应（WGS）活性和高的轻质烃选择性。但Fe/Cu/K/Al2O3催化剂比Fe/Cu/K/SiO2催化剂具有更好的运行稳定性。     

铜基催化剂催化合成气一步合成甲醇和甲酸甲酯IV.空速、反应时间、杂质和Cu-Cr摩尔比的影响(英文)

在低温低压和浆态反应条件下,考察了空速、反应时间、杂质及Ｃｕ－Ｃｒ摩尔比对铜基催化剂催化合成气一步合成甲醇和甲酸甲酯反应的影响。实验结果表明,空速对催化剂活性有较显著的影响;ＣＯ转化率与反应时间无关,但Ｈ２的转化率与反应时间有关。在１５小时之内Ｈ２的转化率随反应时间增加而缓慢增加,此后与反应时间无关。此外,高浓度的杂质使催化剂的活性和寿命下降,而且Ｃｕ／Ｃｒ摩尔比和热处理气氛对催化剂的物相和活性也有显著的影响。     

Study on Highly Active Catalysts and a Once—Through Process for Methanol Synthesis from Syngas

Highly active CNT-promoted co-precipitated Cu-ZnO-Al2O3 catalysts, symbolized as CuiZnj;Alfc-a;%CNTs, were prepared, and their catalytic activity for once-through methanol synthesis from syngas was investigated. The results illustrated that, under the reaction conditions (at 493 K, 5.0 MPa, the volume ratio of H2/CO/CO2/N2= 62/30/5/3, GHSV= 4000 h-1), the observed single-pass CO-conversion and methanol-STY over a Cu6Zn3Al1-12.5%CNTs catalyst reached 64% and 1210 mg/(h-g), which was about 68% and 66% higher than those (38% and 730 mg/(h-g)) over the corresponding CNT-free catalyst, Cu6Zn3Al1, respectively. The characteristic studies of the catalysts revealed that appropriate incorporation of a minor amount of the CNTs into the CuiZnjAlk brought about little change in the apparent activation energy of the methanol synthesis reaction, however, led to a considerable increase in the catalyst's active Cu surface area and pronouncedly enhanced the stationary-state concentration of active hydrogen-adspecies on     

甲醇水蒸气重整制氢CuO/CeO2-ZrO2/SiC整体催化剂的研究

采用浸渍法和溶胶凝胶法制备了CuO/CeO₂-ZrO₂/SiC整体催化剂，并将其用于甲醇水蒸气重整制氢反应中。结果表明，与CuO/CeO₂-ZrO₂颗粒催化剂相比，CuO/CeO₂-ZrO₂/SiC整体催化剂催化活性较好，产氢速率较快且重整气中CO体积分数较低。进一步探究了涂层涂覆量和CuO负载量对催化性能的影响，结果表明，当CeO₂-ZrO₂复合氧化物涂层涂覆量在15%±1%，CuO负载量为5%±1%时，催化性能较好；当反应温度为340℃，水醇物质的量比为1.2，甲醇水蒸气气体空速为4840 h^-1时，甲醇转化率为86.0%，产氢速率为1490.0 L/（m³·s），重整气中CO体积分数为1.55%。最后通过单因素实验法探究了甲醇水蒸气气体空速、水醇物质的量比和反应温度对反应的影响。结果表明，随着气体空速变大，甲醇转化率下降，产氢速率上升，重整气中CO体积分数下降。随着水醇物质的量比增加，甲醇转化率先上升后下降，产氢速率先上升后下降，重整气中CO体积分数下降。随着反应温度的升高，甲醇转化率、产氢速率和重整气中CO体积分数均上升。     

Catalytic behaviors of Co-Mn/TiO2 catalysts for Fischer-Tropsch synthesis

The 15%(Co-Mn)/TiO₂,(Co/Mn=1/6) catalyst was prepared using fusion procedure and studied for the conversion of synthesis gas to C_2~4 olefins. The effects of calcination conditions and operation conditions such as the H₂/CO molar feed ratio at different temperatures, gas hourly space velocity (GHSV) and total reaction pressure on the catalytic performance of catalyst were investigated. The stability of the catalyst during 150 h at optimal operation conditions (t=250 ℃ H₂/CO=2/1, GHSV=1 500 h^-1 and p=0.3 MPa) has been investigated. It is found that this catalyst is high stable for production C_2~4 olefins. Characterizations of both precursors and calcined catalysts by powder X-ray diffraction, scanning electron microscopy (SEM), Brunauer-Emmett-Teller (BET) specific surface area measurement and thermal analysis methods such as thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC) show that the different preparation method influences the catalyst precursor structure and morphology.     

Re/Pt/Ce0.8Zr0.2O2/蜂窝整体催化剂上低温水煤气变换反应动力学研究

采用微分反应器,研究了新型Re/Pt/Ce0.8Zr0.2O2/蜂窝催化剂上低温水煤气变换反应的动力学行为。利用非线性最小二乘法处理正交设计的实验数据,获得了动力学方程的模型参数。所得的结果符合幂函数型动力学方程,经F检验和相关指数检验,实验值和模拟计算值符合较好。在该催化剂上水煤气变换反应的活化能为70kJ/mol,与文献中报道的数值相吻合。该催化剂上反应速率对CO、H2O、H2和CO2的反应级数分别为0.09、0.88、-0.54和-0.11,与传统的Cu基低变催化剂上的反应级数相差较大。这表明,低温水煤气变换反应在两种催化剂上遵循不同的反应机理。     

Zn0.2Zr0.8Ox固溶体催化剂的制备及其催化甲醇合成性能

以Zn(NO3)2·6H2O、Zr(NO3)4·5H2O为原料,Na2CO3为沉淀剂,采用并流共沉淀法制备了一系列不同Zn/Zr摩尔比的双金属氧化物催化剂,其结构经XRD、BET、Raman光谱、TEM和H2-TPR表征。结果表明:Zn0.2Zr0.8Ox催化剂为固溶体结构,比表面积最大达46.2 m^2·g^-1,还原性能良好。以催化CO2加氢合成甲醇为目标反应,对不同Zn/Zr摩尔比的催化剂进行性能测试,并考察了反应温度和反应时间对Zn0.2Zr0.8Ox催化剂性能的影响。结果表明:反应温度250℃、空速GHSV为12000 mL·g^-1h^-1、反应压力2 MPa和H2/CO2(体积比)=3/1时,Zn0.2Zr0.8Ox固溶体催化剂催化活性最高,二氧化碳转化率达到了3.5%、甲醇选择性高达75.4%,甲醇收率达到2.6%,且催化剂能够稳定运行100 h而不失活。     

Cu/ZnO催化糠醛气相加氢制2-甲基呋喃的研究

通过共沉淀法制备一系列铜锌催化剂,用于固定床上糠醛气相加氢制2-甲基呋喃的研究。采用X射线衍射仪(XRD)、N_2吸附-脱附、扫描电子显微镜(SEM)、H_2-程序升温还原(H_2-TPR)、NH_3-程序升温脱附(NH_3-TPD)表征,分析催化剂中Cu0和ZnO在催化反应中的作用。结果表明,Cu~0是糠醛加氢的活性中心,氧化锌的加入减小了催化剂晶粒粒径、增大了催化剂比表面积、利于催化剂还原和增加催化剂表面弱酸性位。当Cu/Zn物质的量比为1∶2时,Cu_1Zn_2催化剂具有适宜氧化还原活性中心及弱酸位数量,对2-甲基呋喃表现出较高的选择性。Cu_1Zn_2催化剂在常压、反应温度为200℃、氢醛物质的量比为4∶1、糠醛体积空速为0.3 h-1条件下,糠醛转化率100.0%,2-甲基呋喃选择性最高为93.6%。反应稳定运行200 h后,糠醛转化率仍为100.0%,2-甲基呋喃选择性为80.0%,糠醇选择性为11.4%。     

Performance and characterization of iron-nickel catalysts for light olefin production

A series of x (Fe, Ni)/Al2O3 catalysts (x = 2--12 wt%) were prepared using incipient wetness method and studied for the conversion of synthesis gas to light olefins. 6 wt%(Fe, Ni)/Al2O3 catalyst was found to be the optimal catalyst for the production of C2--C4 olefins. The effects of calcination behaviors and operational conditions on the catalytic performance of the optimal catalyst were investigated. The best operational conditions were molar feed ratio H2/CO = 2/1, T = 260 ℃, gas hourly space velocity (GHSV) = 2600 h-1 and the pressure of 3 bar. Characterizations of both precursors and catalysts were carried out using X-ray diffraction (XRD), temperature-programmed reduction (TPR), scanning electron microscopy (SEM), N2-adsorption-desorption measurement, thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC).