Effects of complexants on [Ni1/3Co1/3Mn1/3]CO3 morphology and electrochemical performance of LiNi1/3Co1/3Mn1/3O2

LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials for the application of lithium ion batteries were synthesized by carbonate co-precipitation routine using different ammonium salt as a complexant. The structures and morphologies of the precursor [Ni_1/3Co_1/3Mn_1/3]CO₃ and LiNi_1/3Co_1/3Mn_1/3O₂ were investigated through X-ray diffraction, scanning electron microscope, and transmission electron microscopy. The electrochemical properties of LiNi_1/3Co_1/3Mn_1/3O₂ were examined using charge/discharge cycling and cyclic voltammogram tests. The results revealed that the microscopic structures, particle size distribution, and the morphology properties of the precursor and electrochemical performance of LiNi_1/3Co_1/3Mn_1/3O₂ were primarily dependent on the complexant. Among all as-prepared LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials, the sample prepared from Na₂CO₃–NH₄HCO₃ routine using NH₄HCO₃ as the complexant showed the smallest irreversible capacity of 19.5 mAh g⁻¹ and highest discharge capacity of 178.4 mAh g⁻¹ at the first cycle as well as stable cycling performance (98.7% of the initial capacity was retained after 50 cycles) at 0.1 C (20 mA g⁻¹) in the voltage range of 2.5–4.4 V vs. Li⁺/Li. Moreover, it delivered high discharge capacity of over 135 mAh g⁻¹ at 5 C (1,000 mA g⁻¹).     

3-Ferrocenyl-1-methyl- and 1-ferrocenyl-3-methylcyclopropenes

Dehydrobromination of isomeric 3-bromo-1-ferrocenyl-2-methylcyclopropanes afforded 3-ferrocenyl-1-methyl- and 1-ferrocenyl-3-methylcyclopropenes. These undergo smooth opening of the three-membered ring to give 1- and 2-ferrocenylbuta-1,3-dienes and 1- and 2-methyl-1H-cyclopentaferrocenes; with 1,3-diphenylisobenzofuran they give the classical Diels-Alder adducts.     

A novel synthesis of α-hydroxy- and α,α′-dihydroxyketone from α-iodo and α,α′-diiodo ketone using photoirradiation

A novel reaction of α-iodo ketone (α-iodocycloalkanone, α-iodo-β-alkoxy ester, and α-iodoacyclicketone) with irradiation under a high-pressure mercury lamp gave the corresponding α-hydroxyketone in good yields. In the case of α,α′-diiodo ketone, α,α′-dihydroxyketone which little has been reported until now was obtained. This reaction affords a new, clean and convenient synthetic method for α-hydroxy- and α,α′-dihydroxyketone.     

Microwave-assisted synthesis of α-hydroxy ketone and α-diketone and pyrazine derivatives from α-halo and α,α′-dibromo ketone

A novel reaction of α-halo ketone (α-bromo and α-chloro ketone) with irradiation under microwave gave the corresponding α-hydroxyketone and pyrazine derivative in good yields. In the case of α,α′-dibromo ketone, α-diketone was obtained. This reaction affords a new, clean and convenient synthetic method for α-hydroxyketone, α-diketone, α-chloro ketone and pyrazine derivative.     

X-ray diffraction study of ceramic samples of SrCu1/3Nb1/3O3

Ceramic samples of SrCu_1/3Nb_2/3O₃, obtained either by slow cooling or by quenching from 1200°C, were studied by X-ray diffraction using the Rietveld method. The slow-cooled SrCu_1/3Nb_2/3O₃ samples contain one phase with a perovskite structure (R _B = 4.14%, tetragonal crystal symmetry, space group P4/mmm, Z = 1, a = 3.935 ?, c = 4.124 ?), its diffraction peaks being considerably broadened. The samples quenched from 1200°C contain two SrCu_1/3Nb_2/3O₃ forms with a perovskite structure: one of them is oxygen deficient (R _B = 3.37%, tetragonal crystal symmetry, space group P4/mmm, Z = 1, a = 3.9687 ?, c = 4.0718 ?), and the other has no oxygen deficiency (R _B = 3.20%, tetragonal crystal symmetry, space group P4/mmm, Z = 1, a = 3.95307 ?, c = 4.08935 ?).     

Electron impact fragmentations of 1- and 3-aryl-3-buten-1-ols

The electron impact fragmentation of 1- and 3-aryl-3-buten-1-ols show several distinguishing fragmentations. α-Cleavage predominates in the fragmentation of the 1-aryl-3-buten-1-ols to such an extent that molecular ions of only low intensity are observed. The ion resulting from α-cleavage fragments readily with the loss of the ring substituent to the phenyl ion. An intense molecular ion is observed in the 3-aryl series and a loss of 70 u is a major fragmentation in this series. Based on deuterium labeling studies, this unique fragmentation was explained by a hydroxylic hydrogen migration to the ring accompanied by the loss of allene and formaldehyde. Other major fragmentations observed in the 3-aryl series are: a McLafferty-type rearrangement (loss of formaldehyde), loss of 33 u (water + methyl radical), and the loss of 43 u (C₂H₃O and C₃H₇). The proposed mechanisms have been substantiated by deuterium labeling and high resolution mass spectrometry. Substituent effects play a major role in the 3-aryl series, but are insignificant in the 1-aryl series.     

Improvement of electrochemical properties of LiNi1/3Mn1/3Co1/3O2 by coating with La0.4Ca0.6CoO3

In this paper, La_0.4Ca_0.6CoO₃-coated LiNi_1/3Mn_1/3Co_1/3O₂ is successfully prepared by the sol–gel method associated with microwave pyrolysis method. The structure and electrochemical properties of the La_0.4Ca_0.6CoO₃-coated LiNi_1/3Co_1/3Mn_1/3O₂ are investigated by using X-ray diffraction (XRD), electrochemical impedance spectroscopy (EIS), and charge/discharge tests. XRD analyses show that the La_0.4Ca_0.6CoO₃ coating does not change the structure of LiNi_1/3Co_1/3Mn_1/3O₂. The electrochemical performance studies demonstrate that 2 wt.% La_0.4Ca_0.6CoO₃-coated LiNi_1/3Co_1/3Mn_1/3O₂ powders exhibit the best electrochemical properties, with an initial discharge capacity of 156.9 mAh g^–1 and capacity retention of 98.9 % after 50 cycles when cycled at a current density of 0.2 C between 2.75 and 4.3 V. La_0.4Ca_0.6CoO₃ coating can improve the rate performance because of the enhancement of the surface electronic/ionic transportation by the coating layer. EIS results suggest that the coating La_0.4Ca_0.6CoO₃ plays an important role in suppressing the increase of cell impedance with cycling especially for the increase of charge-transfer resistance.     

Synthesis and surface treatment of LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion batteries

In order to shorten process time and possibly reduce synthesis cost of LiNi_1/3Co_1/3Mn_1/3O₂, the cathode material was prepared by solution combustion and microwave synthesis routes with reduced duration of calcination. The products were also surface-modified with Al₂O₃ by a mechano-thermal coating process to enhance cyclability. The structure and morphology of the bare and the surface-modified LiNi_1/3Co_1/3Mn_1/3O₂ samples were characterized by X-ray diffraction, field-emission scanning electron microscopy, transmission electron microscopy, energy-dispersive spectroscopy, and differential scanning calorimetry techniques. At a 0.1-C rate and between 4.6 and 2.5 V, the products delivered a first-cycle discharge capacity of as much as 195 mA h/g. Surface modification of LiNi_1/3Co_1/3Mn_1/3O₂ with alumina resulted in improved cyclability.     

Aromaten-Komplexe mit Halbsandwich-Struktur: Die 1:1-Komplexe des Mesitylens mit SbCl3, SbBr3, BiCl3 und BiBr3

Arene Complexes with a Half-Sandwich Structure: The 1:1 Complexes of Mesitylene with SbCl₃, SbBr₃, BiCl₃, and BiBr₃ 1,3,5-Trimethylbenzene forms stable 1:1 complexes with SbCl₃, SbBr₃, BiCl₃, and BiBr₃ of the stoichiometry C₆H₃Me₃·EX₃ ( 1 – 4 ). According to the results of X-ray structure analyses of compounds 2 and 3 , one arene molecule is coordinated to each antimony or bismuth atom characterizing these adducts as half-sandwich species. To a good approximation the mesitylene molecules are centered over the metal atoms, but deviations from strict η⁶-hapticity are larger for antimony than for bismuth. – Despite some obvious analogies in many features of the structures, 2 and 3 are not isostructural. Differences appear with regard to the halogen bridging between the EX₃ moieties giving rise to the formation of two-dimensional networks (EX₃)_n covered above and below by mesitylene molecules. The structural and sequential principles of the layers differ in a characteristic way for 2 and 3 .     

A study on carbon-coated LiNi1/3Mn1/3Co1/3O2 cathode material for lithium secondary batteries

The surface of LiNi_1/3Mn_1/3Co_1/3O₂ was coated with amorphous carbon to enhance the conductivity of the material. Electrochemical studies were performed by assembling 2032 coin cells with lithium metal as an anode. When carbon was coated on the surface, the LiNi_1/3Mn_1/3Co_1/3O₂ cathode material showed an improved rate capability, thermal stability, and cycle performance.     

Biosynthesis of aristeromycln: Evidence for the intermediacy of a 4β-hydroxymethyl-1α, 2α, 3α-trihydroxycyclopentanetriol.

Evidence for the intermediacy of a 4β-hydroxymethyl-1α, 2α, 3α-trihydroxycyclopentanetdol (5 or6) in the biosynthesis of the nucleoside antibiotic aristeromycin (1) has been obtained by administration of doubly-labeled forms of D-glucose to the fermentation broth ofStreptomyces citricolor followed by trapping of the tetrol5 using isotope dilution methods.     

Electrochemical behavior of spherical LiNi1/3Co1/3Mn1/3O2 as cathode material for aqueous rechargeable lithium batteries

Spherical LiNi_1/3Co_1/3Mn_1/3O₂ powders have been synthesized from co-precipitated spherical metal hydroxide. The electrochemical performances of the LiNi_1/3Co_1/3Mn_1/3O₂ electrodes in 1 M LiNO₃, 5 M LiNO₃, and saturated LiNO₃ aqueous electrolytes have been studied using cyclic voltammetry and ac impedance tests in this work. The results show that LiNi_1/3Co_1/3Mn_1/3O₂ electrode in saturated LiNO₃ electrolyte exhibits the best electrochemical performance. An aqueous rechargeable lithium battery containing LiNi_1/3Co_1/3Mn_1/3O₂ cathode, LiV_2.9Ni_0.050Mn_0.050O₈ anode, and saturated LiNO₃ electrolyte is fabricated. The battery delivers an initial capacity of 98.2 mAh g⁻¹ and keeps a capacity of 63.9 mAh g⁻¹ after 50 cycles at a rate of 0.5 C (278 mA g⁻¹ was assumed to be 1 C rate).     

The gas-phase elimination kinetics of 3-buten-1-methanesulphonate and 3-methyl-3-buten-1-methanesulphonate

The elimination kinetics of the title compounds were carried out in a static system over the temperature range of 290–330°C and pressure range of 29.5–124 torr. The reactions, carried out in seasoned vessels with allyl bromide, obey first-order rate law, are homogeneous and unimolecular. The temperature dependence of the rate coefficients is given by the following Arrhenius equations: for 3-buten-1-methanesulphonate, log k₁(s^?1) = (12.95 ± 0.53) ? (175.3 ± 5.9)kJ mol^?1(2.303RT)^?1; and for 3-methyl-3-buten-1-methanesulphonate, log k₁(s^?1) = (12.98 ± 0.40) ? (174.7 ± 4.5)kJ mol^?1(2.303RT)^?1. The olefinic double bond appears to assist in the rate of pyrolysis. The mechanism is described in terms of an intimate ion-pair intermediate. © 1995 John Wiley & Sons, Inc.     

Reversible Anionic Redox Activities in Conventional LiNi1/3Co1/3Mn1/3O2 Cathodes

Redox reactions of oxygen have been considered critical in controlling the electrochemical properties of lithium‐excessive layered‐oxide electrodes. However, conventional electrode materials without overlithiation remain the most practical. Typically, cationic redox reactions are believed to dominate the electrochemical processes in conventional electrodes. Herein, we show unambiguous evidence of reversible anionic redox reactions in LiNi_1/3Co_1/3Mn_1/3O₂. The typical involvement of oxygen through hybridization with transition metals is discussed, as well as the intrinsic oxygen redox process at high potentials, which is 75 % reversible during initial cycling and 63 % retained after 10 cycles. Our results clarify the reaction mechanism at high potentials in conventional layered electrodes involving both cationic and anionic reactions and indicate the potential of utilizing reversible oxygen redox reactions in conventional layered oxides for high‐capacity lithium‐ion batteries.     

Calorimetric and structural studies of La1-xYxAlO3 and Y1-xLuxAlO3 crystals

Powder X-ray diffraction measurements of La_1-xY_xAlO₃ suggested that the space groups of x=0.3 and 0.9 samples are Pnma at room temperature and that a structural phase transition occurs from R-3c to Pnma above 200 K in x=0.1 sample. The unit cell volumes of x=0.1, 0.3, and 0.9 samples at 20 K are larger than the average one estimated from the volumes of LaAlO₃ and YAlO₃. The heat capacities of x=0.1 and 0.3 samples are larger than those of LaAlO₃ in the range 3-20 K. On the other hand, the volumes of Y_1-xLu_xAlO₃ (x=0.1, 0.3, and 0.5) at 20 K are close to the average one and the heat capacity increased as x is increased in the range 3-20 K. This revised version was published online in August 2006 with corrections to the Cover Date.     

Kinetics of the reactions of cyclopropane derivatives. V. The gas-phase unimolecular reactions of 1 α-chloro-2α,3α-dimethylcyclopropane and 1α-chloro-2α,3β-dimethylcyclopropane

Thermolysis of the “all-cis” compound 1α-chloro-2α,3α-dimethylcyclopropane (A) at 550–607 K and 6–115 torr is a first-order homogeneous non-radical-chain process giving penta-1,3-diene (PD) and HCl as products. The Arrhenius parameters are log₁₀A(sec^?1) = 13.92 ± 0.08 and E = 199.6 ± 0.9 kJ/mol. The isomer with trans-methyl groups, 1α-chloro-2α,3β-dimethylcyclopropane (B) reacts by two parallel first-order processes giving as observed products trans-4-chloropent-2-ene (4CP) and PD + HCl, with log₁₀A(sec^?1) = 14.6 and 13.8, respectively, and E = 199.5 and 190.2 kJ/mol, respectively. The 4CP undergoes secondary decomposition to PD + HCl (as investigated previously). Comparison of the results for compounds (A) and (B) with those for other gas-phase and solution reactions leads to the conclusion that the gas-phase thermolyses proceed by rate-determining ring opening to form olefins which may decompose further by thermal or chemically activated reactions, and that the ring opening is a semiionic electrocyclic reaction in which alkyl groups in the 2,3-positions trans to the migrating chlorine semianion move apart, with appropriate consequences for the rate of reaction and the stereochemistry of the products.     

Synthesis and Dehydrobromination of 3-Bromomethyl- and 3-Bromo-3-methoxymethylcyclobutane-1-carbonitriles and Methyl 3-Bromomethyl- and 3-Bromo-3-methoxymethylcyclobutane-1-carboxylates

The anti-Markownikoff products of bromination and bromomethoxylation of 3-methylenecyclobutane-1-carbonitrile and methyl 3-methylenecyclobutane-1-carboxylate were subjected to dehydrobromination by the action of potassium tert-butoxide in THF. The reaction takes two elimination pathways: 1,3-dehydrobromination to give bicyclobutane derivatives and 1,2-dehydrobromination leading to substituted methylenecyclobutane. Structural factors in the substrate were revealed, which are responsible for the ratio of the two concurrent elimination processes.     

Synthesis of 3-aryl-5-dichloromethyl-1H-pyrazole-1-carboxamides from 1-aryl-3,4,4-trichlorobut-3-en-1-ones

The reaction of 1-aryl-3,4,4-trichlorobut-3-en-1-ones with semicarbazide hydrochloride in the presence of sodium acetate is accompanied by prototropic allylic rearrangement, leading to the formation of two isomeric products, semicarbazones of the initial ketones and 1-aryl-3,4,4-trichlorobut-2-en-1-one semicarbazones. The latter undergo heterocyclization in the presence of triethylamine to give the corresponding 3-aryl-5-dichloromethyl-1H-pyrazole-1-carboxamides.     

Thermophysical properties of 1-methyl-3-methylimidazolium dimethylphosphate and 1-ethyl-3-methylimidazolium diethylphosphate

The density and surface tension of 1-methyl-3-methylimidazolium dimethylphosphate, [C₁mim](CH₃O)₂PO₂ and 1-ethyl-3-methylimidazolium diethylphosphate, [C₂mim](CH₃CH₂O)₂PO₂ ionic liquids have been measured over the temperature range from (283.15 to 338.15) K. The coefficients of thermal expansion were calculated from the experimental density results using an empirical correlation for T = (283.15 to 338.15) K. Molecular volume and standard entropies of these ILs were calculated from the experimental density values. The surface properties of ILs were investigated. The critical temperature and enthalpy of vapourization were also discussed.     

3-Nitro-1-nitromethyl-1H-1,2,4-triazole

The title compound, C₃H₃N₅O₄, consists of three planar fragments twisted in relation to each other, namely a triazole ring, a nitro­methyl­ene group and a nitro group. Molecular conformation analysis shows that the first stage of thermal decomposition is a breakage of the H₂C—NO₂ bond. There are essential conformational differences in the mol­ecule in comparison with semi-empirical calculations.