可溶性聚噻吩甲烯包覆碳纳米管的三阶非线性光学响应

采用原位聚合的方法合成了聚(3-己基噻吩)-2,5-二(4-羟基-3-甲氧基苯甲烯)包覆的多壁碳纳米管(PHTHMOBQ/MWNTs). 荧光光谱分析表明, PHTHMOBQ/MWNTs复合体中, 碳纳米管与共轭聚合物PHTHMOBQ之间形成光致电子转移体系, 使得π电子离域程度增加, 并且导致荧光量子效率降低. 根据E_g与入射光子能量hν的关系, 拟合了PHTHMOBQ/MWNTs薄膜的光学禁带宽度. 发现随着碳纳米管含量的增加, E_g逐步减小. 采用简并四波 关键词： 共轭聚合物 碳纳米管 光致电子转移 三阶非线性光学效应     

The Effects of Copper and Polytetrafluoroethylene (PTFE) on Thermal Conductivity and Tribological Behavior of Polyoxymethylene (POM) Composites

The effects of copper and polytetrafluoroethylene (PTFE) on thermal conductivity and tribological behavior of polyoxymethylene (POM) composites were investigated by a hot disk thermal analyzer and an M-2000 friction and abrasion testing machine. The results indicated that the incorporation of 3 wt% copper particles into POM had little effect on the thermal conductivity of POM composites, but led to the decreased friction coefficient and wear rate of composites. As the copper content was increased, the thermal conductivity increased and reached 0.477 W m^?1 K^?1 for POM-25% Cu composite, an increase of 35.9% compared with that of unfilled POM, while the friction coefficient and wear rate of composites also increased. The incorporation of PTFE into POM-Cu composites had a negligible effect on the thermal conductivity of composites, but helped in the formation of a continuous and uniform transfer film and resulted in the reduction in the friction coefficient and wear rate of composites. The POM-15% Cu-10% PTFE composite, with a value of wear rate similar to unfilled POM possessed higher thermal conductivity and lower friction coefficient.     

Automatic dispersion,long-term stability of multi-walled carbon nanotubes in high concentration electrolytes

Nanoparticles have been known as the useful materials in working fluids for petroleum industry. But the stabilization of nano-scaled materials in water-based working fluids at high salinities is still a big challenge. In this study, we successfully prepared the anionic polymer/multi-walled carbon nanotubes (MWNTs) composites by covalently wrapping of MWNTs with poly (sodium 4-styrenesulfonate) (PSS) to improve the stability of MWNTs in high concentration electrolytes. The PSS/MWNTs composites can automatically disperse in salinity up to 15 wt% NaCl and API brines (8 wt% NaCl?+?2 wt% CaCl₂). Hydrodynamic diameters of composites were measured as a function of ionic strength and API brines by dynamic light scattering (DLS). By varying the concentration of brines, hydrodynamic diameter of PSS/MWNTs composites in brines fluctuated between 545?±?110 nm for 14 days and 673?±?171 nm for 30 days. Above results showed that PSS/MWNTs could be well stable in high salts solutions for a long period of time. After wrapped with PSS, the diameters of nanotubes changed from 30?~?40 to ~?430 nm, the thickness of wrapped polymer is about ~?400 nm by analysis of morphologies. The zeta potentials of PSS/MWNTs composites in various salinity of brines kept at approximately ??41?~???52 mV. Therefore, the well dispersion of PSS/MWNTs in high salinity is due to large negative charges of poly (sodium 4-styrenesulfonate), which provide enough electrostatic repulsion and steric repulsion to hinder compression of electric double layer caused by high concentration electrolytes.     

Covalent attachment of polystyrene on multi-walled carbon nanotubes via nitroxide mediated polymerization

A new method to attach polymers on carbon nanotubes has been studied. We used nitroxide mediated polymerization (NMP) to graft polystyrene from multi-walled carbon nanotubes (MWNTs). Carboxyl groups on MWNTs were activated with thionyl chloride (SOCl₂) to give acyl chloride derivative (MWNT-COCl). NMP initiator was introduced to MWNT by esterification of 1-hydroxy-2-phenyl-2-(2′,2′, 6′, 6′-tetramethyl-1′-piperidinyloxy)ethane (HO-PE-TEMPO) with acyl chloride groups of MWNTs. The obtained MWNT-PE-TEMPO was used for initiation of bulk polymerization of styrene, yielding polystyrene-grafted MWNTs (MWNT-g-pSt). The resulting composites of MWNT-g-pSt were analyzed by TEM, SEM, FT-IR and TGA.     

Carbon nanotube-epoxy composites: The role of acid treatment in thermal and electrical conductivity

Wet acid oxidation treatment methods have been widely reported as an effective method to purify and oxidize the surface of industrial multi-walled carbon nanotubes. This work examines the use of a concentrated HNO₃/H₂SO₄ mixture in an attempt to optimize the purification procedure of industrial multi-walled carbon nanotubes with diameter distribution statistics. It is shown that acid treatments of several hours are enough to purify the nanotubes. The electrical and thermal conductivities of epoxy composites containing 0.05–0.25 wt% of an acid-treated multi-walled carbon nanotube have been studied. The electrical conductivity of the composites decreases by more than three orders, whereas the thermal conductivity of the same specimen increases very modestly as a function of the filler content.     

Electrical, dielectric and surface wetting properties of multi-walled carbon nanotubes/nylon-6 nanocomposites

This paper reports that the multi-walled carbon nanotubes(MWCNT)/nylon-6 (PA6) nanocomposites with different MWCNT loadingshave been prepared by a simple melt-compounding method. Theelectrical, dielectric, and surface wetting properties of theCNT/PA6 composites have been studied. The temperature dependence ofthe conductivity of the CNT/PA6 composite with 10.0 wt{\%} CNTloading ($\sigma _{\rm RT} \sim 10^{-4}$ S/cm) are measured, andafterwards a charge-energy-limited tunnelling model (ln $\sigma (T)\sim T^{-1/2})$ is found. With increasing CNT weight percentage from0.0 to 10.0 wt%, the dielectric constant of the CNT/PA6composites enhances and the dielectric loss tangent increases twoorders of magnitude. In addition, water contact angles of theCNT/PA6 composites increase and the composites with CNT loadinglarger than 2.0 wt%even become hydrophobic. The obtainedresults indicate that the electrical and surface properties of thecomposites have been significantly enhanced by the embedded carbonnanotubes.     

Novel Cu–Cr alloy matrix CNT composites with enhanced thermal conductivity

Carbon nanotubes (CNTs) are incorporated into the Cu–Cr matrix to fabricate bulk CNT/Cu–Cr composites by means of a powder metallurgy method, and their thermal conductivity behavior is investigated. It is found that the formation of Cr₃C₂ interfacial layer improves the interfacial bonding between CNTs and Cu–Cr matrix, producing a reduction of interfacial thermal resistance, and subsequently enhancing the thermal conductivity of the composites. The thermal conductivity of the composites increases by 12 % and 17 % with addition of 5 vol.% and 10 vol.% CNTs, respectively. The experimental results are also theoretically analyzed using an effective medium approximation (EMA) model, and it is found that the EMA model combined with a Debye model can provide a satisfactory agreement to the experimental data.     

Influence of filler alignment in the mechanical and electrical properties of carbon nanotubes/epoxy nanocomposites

In this work, we report the mechanical and electrical properties of carbon nanotubes/epoxy composites prepared with aligned and randomly oriented nanotubes as filler. The samples are disks of 30 mm in diameter and 3 mm in thickness. To obtain the carbon nanotubes alignment, an external electric field (250 VAC; 50 Hz) was applied through the thickness of the sample during all the cure process. The AC electrical current was measured, during the cure, as a strategy to determine the optimum time in which the alignment reaches the maximum value. DC conductivity measured after the cure shows a percolation threshold in the filler content one order of magnitude smaller for composites with aligned nanotubes than for composites with randomly oriented filler (from 0.06 to 0.5 wt%). In the percolation threshold, the achieved conductivity was 1.4×10⁻⁵ Sm⁻¹. In both cases, aligned and randomly distributed carbon nanotube composites, the wear resistance increases with the addition of the filler while the Rockwell hardness decreases independently of the nanotubes alignment.     

Investigating interfacial contact configuration and behavior of single-walled carbon nanotube-based nanodevice with atomistic simulations

Carbon nanotubes (CNTs), including single-walled carbon nanotubes (SWNTs) and multi-walled carbon nanotubes (MWNTs), are considered to be the promising candidates for next-generation interconnects with excellent physical and chemical properties ranging from ultrahigh mechanical strength, to electrical properties, to thermal conductivity, to optical properties, etc. To further study the interfacial contact configurations of SWNT-based nanodevice with a 13.56-Å diameter, the corresponding simulations are carried out with the molecular dynamic method. The nanotube collapses dramatically into the surface with the complete collapse on the Au/Ag/graphite electrode surface and slight distortion on the Si/SiO₂ substrate surface, respectively. The related dominant mechanism is studied and explained. Meanwhile, the interfacial contact configuration and behavior, depended on other factors, are also analyzed in this article.     

Designing of multiwalled carbon nanotubes reinforced low density polyethylene nanocomposites for suppression of electromagnetic radiation

High aspect ratio multi-walled carbon nanotubes (MWCNTs) reinforced low density polyethylene (LDPE) composites were prepared by solvent casting followed by compression molding technique. Electromagnetic interference (EMI) shielding effectiveness (SE) of these composites was investigated in the frequency range of 12.4?C18 GHz (Ku-band) for the first time. The experimental results indicate that the EMI-SE of these composites is sensitive to the MWCNT loading. The average value of EMI-SE reaches 22.4 dB for 10 wt% MWCNT-LDPE composites, indicating the usefulness of this material for EMI shielding in the Ku-band. The main reason for improved SE has been attributed to significant improvement in the electrical conductivity of the composites by 20 orders of magnitude, i.e., from 10^?20 for pure LDPE to 0.63 S/cm for MWCNT-LDPE, which is three order of magnitude higher than the previous reports for MWCNT-LDPE composites. Differential scanning calorimetry of the MWCNT-LDPE composites showed around 37% improvement in the crystalline contents over pure LDPE samples which resulted into enhanced thermal stability of the composites. The thermal decomposition temperature of LDPE is shifted by 40 °C on addition of 5 wt% MWCNT. The studies therefore show that these composite can be used as light weight, thermally stable EMI shielding, and antistatic material.     

Comparison of different types of polypyrimidine/CNTs/Pt hybrids in fuel cell catalysis

In this paper, we mainly studied the preparation of platinum-containing composite materials with carbon nanotubes wrapped by polypyrimidine-conjugated polymers and the performance of the composites. The polymer-based carbon nanotubes/Pt catalysts were prepared successfully and confirmed by infrared spectroscopy, XPS, XRD, and TEM images. The performance of polypyrimidine/multi-walled carbon nanotubes (MWCNTs)/Pt and polypyrimidine/double-walled carbon nanotubes (DWCNTs)/Pt was compared with the polypyrimidine/single-walled carbon nanotubes (SWCNTs)/Pt. The amount of the loaded Pt on the polypyrimidine/MWCNTs and polypyrimidine/DWCNTs was calculated to be 50.5 wt% and 52.7 wt% respectively. The effective specific surface area of the polypyrimidine/MWCNTs/Pt (45.7 m²/g) and polypyrimidine/DWCNTs/Pt (42.47 m²/g) was observed by electrochemical cyclic voltammetry. These studies strongly imply that the MWCNTs were better candidates than DWCNTs and SWCNTs in the application of polypyrimidine/CNT materials as catalyst for fuel cells.     

Preparation and properties of alumina composites modified by electric field-induced alignment of carbon nanotubes

Catalytic chemical vapor deposition (CVD) grown multi-walled carbon nanotubes (MWNTs) are treated with HF and deionized water and are then placed into alumina ceramics for improvement of both electrical conductivity and mechanical properties. In particular, an alternating current (ac) electric field is applied during the coagulation of the alumina slurries to induce the formation of aligned MWNT networks in the alumina matrix. The coagulated alumina matrix composite bases filled with 2 wt. % ac electric field-induced aligned MWNTs, are then sintered by hot pressing. The electrical conductivities of the prepared composites in directions both parallel and perpendicular to the MWNTs alignment, reach values of 6.2×10^-2 S m^-1 and 6.8×10^-9 S m^-1, respectively, compared with that of 4.5×10^-15 S m^-1 for pristine alumina ceramics. The fracture toughness and flexing strengths of the prepared composites in the two directions are 4.66±0.66 MPa m^0.5, 390±70 MPa, and 3.65±0.46 MPa m^0.5, 191±5 MPa, respectively, compared with 3.78±0.66 MPa m^0.5 and 302±50 MPa for pristine alumina, 4.09±0.15 MPa m^0.5 and 334±60 MPa for alumina filled with 2 wt. % MWNTs prepared without the effect of an electric field, respectively. The results indicate that the electric field leads to anisotropic behaviour. The properties of the composites along the direction of the MWNTs alignment are much improved with the addition of a small amount of CVD grown MWNTs. PACS 61.46.Fg; 61.66.Fn     

Flame retardance and thermal stability of carbon nanotube epoxy composite prepared from sol-gel method

Carbon nanotubes (CNTs) are functionalized by vinyltriethoxysilane (VTES) to incorporate the -O-C₂H₅ functional group and become VTES—CNT. The VTES—CNTs are added to the modified DGEBA epoxy resin that contains silicon to induce the sol-gel reaction. The final products are organic/inorganic nanocomposites. Thermogravimetric analysis (TGA) and differential scanning calorimeter (DSC) are used to study the thermal property of nanocomposites. The T_g was increased from 118 to 160 °C and char yield of composites that contained 9 wt% CNT at 750 °C was increased by 46.94%. The integral procedural decomposition temperature (IPDT) was increased from 890 to 1571 °C. The limiting oxygen index (LOI) and UL-94 tests were classified as the flame retardance. The LOI of composites was increased from 22 to 27 and the UL-94 changed from V-1 to V-0 when the contents were increased to 9 wt%. The nanocomposites had a higher char yield and were highly flame retardant. The products can meet to the requirements of halogen-free and phosphorus-free ecological flame retardant.     

A study on the electrical conductivity of multi-walled carbon nanotube aqueous solution

The electrical conductivity was investigated for multi-walled carbon nanotubes (MWNTs) dissolved in chloroform and toluene, respectively. The electrical conductivity remarkably increased with increase in the content of MWNTs, which is in accordance with Archie's equation . Furthermore, a hypothesis of the electronic transport process was proposed to explain the difference between the solution and the solid compound. In addition, the temperature dependence of the electrical conductivity shows that log σ vs. 1/T exist in a good linear relationship. The activation energy of the electrical conductivity decreased with increase in concentration and an inflexion was observed at 60 °C in MWNT/toluene solution.     

Influence of the electrical field applied during thermal cycling on the conductivity of LLDPE/CNT composites

The effect of the electrical field on the conductivity of linear low-density polyethylene/carbon nanotubes/ (LLDPE/CNT) composites during temperature cycling has been investigated. Under applied voltage a positive resistivity temperature coefficient was observed during heating already at low (2–3 wt%) CNT content, followed by a large negative temperature coefficient during cooling whose value depends on the applied voltage. The resistivity values after thermal cycling were markedly lower, while they slightly increased in the absence of an electrical field. The effects of thermal cycling on structural and physical properties of the composites have been evaluated by X-ray diffraction and differential scanning calorimetry.     

Synthesis of multiwall carbon nanotubes by chemical vapor deposition of ferrocene alone

Multiwall carbon nanotubes (MWNTs) filled with Fe nanoparticles (NPs) have been synthesized by thermal chemical vapor deposition of ferrocene alone as the precursor. The MWNTs were grown at different temperatures: 980 and 800 ^°C. Characterization of as-prepared MWNTs was done by scanning and transmission electron microscopy, and X-ray diffraction. The transmission electron microscopy study revealed that Fe NPs encapsulated in MWNTs grown at 980 and 800 ^°C are spherical and rod shaped, respectively. Room-temperature vibrating sample magnetometer studies were done on the two samples up to a field of 1 T. The magnetization versus magnetic field loop reveals that the saturation magnetization for the two samples varies considerably, almost by a factor of 4.6. This indicates that Fe is present in different amounts in the MWNTs grown at the two different temperatures.     

Fabrication and Properties of Carbon Nanotube and Poly(vinyl alcohol) Composites

Dispersion of carbon nanotubes in a polymer matrix is one of the most critical issues in carbon nanotube/polymer composites. In this paper we discuss the considerable improvement in the dispersion of multiwalled carbon nanotubes (MWNTs) in poly(vinyl alcohol) (PVA) matrix that was attained through gum arabic treatment. The mechanical properties of these MWNT/PVA composites show that only 2 wt% nanotube loading increases the tensile modulus by more than 130%.     

Green chemical functionalization of multiwalled carbon nanotubes with poly(?-caprolactone) in ionic liquids

Multiwalled carbon nanotubes (MWNTs) have been successfully functionalized by free radical addition of 4,4′-azobis(4-cyanopentanol) in aqueous media to generate the terminal-hydroxyl-modified MWNTs (MWNT-OH), followed by surface-initiated in situ ring-opening polymerization of ?-caprolactone in 1-butyl-3-methylimidazolium tetrafluoroborate (BmimBF₄) to obtain poly(?-caprolactone)-grafted MWNTs (MWNT-g-PCL). Spectroscopic methods in conjunction with electron microscopy clearly revealed that hairy PCL chains were chemically attached to the surface of MWNTs to form core-shell nanostructures with the latter as core and the former as shell. With increasing polymerization time from 2 to 8 h, the amount of the grafted-PCL synthesized in BmimBF₄ varies from 30.6 to 62.7 wt%, which is clearly higher than that (41.5 wt%) obtained in 1,2-dichlorobenzene under comparable conditions (8 h). The proposed methodology here uses water and room temperature ionic liquids (RTILs) as the reaction media and promises a green chemical process for functionalizing nanotubes.     

Electrical Impedance Spectroscopic Study of CNT/Ethylene-alt-CO/Propylene-alt-CO Polyketones Nanocomposite

Impedance spectroscopy was utilized to investigate the dielectric properties, ac conductivity and charge transport mechanisms in propylene-alt-CO/ethylene-alt-CO (EPEC) random terpolymer filled with multi-walled carbon nanotubes (MWCNT) as a function of nanofiller content, frequency, and temperature. Equivalent resistor-capacitor (RC) circuit models were proposed to describe the impedance characteristics of the unfilled terpolymer and the nanocomposite at different temperatures. For the nanocomposites, the ac conductivity tended to be frequency independent at low frequencies. At high frequencies, the ac conductivity increased with frequency. The dc conductivity (i.e., plateau of the ac conductivity at low frequencies) at room temperature increased from 10^?9 (Ω·m)^?1 for the unfilled polymer to l0^?3 (Ω·m)^?1 for the 6 wt% MWCNT/EPEC nanocomposite. At low temperatures, the equivalent RC model for EPEC-0 and EPEC-2 was found to consist of a parallel RC circuit. However, for 6 wt% MWCNT/EPEC nanocomposite, an RC model consisting of an R/constant phase element (CPE) circuit and a resistor in series was required to describe the impedance behavior of the nanocomposite.     

Synthesis and characterization of multi–wall carbon nanotubes supported-hydrated iron phosphate cathode material for lithium–ion cells by a novel homogeneous precipitation method

Iron phosphate (FePO₄) is a promising candidate for the cathode material in lithium-ion cells due to its easy synthesis and low cost. However, the intrinsic drawbacks of FePO₄ material (i.e., the low electronic conductivity and the low lithium-ion diffusion coefficient) result in poor capacity. To overcome the shortcomings, multi-wall carbon nanotubes (MWNTs) supported hydrated iron phosphate nanocomposites (FePO₄·2H₂O/MWNTs) are prepared using a novel homogeneous precipitation method. Meanwhile, the formation mechanism of highly dispersed and ultrafine FePO₄·2H₂O nanoparticles is discussed in detail. Electrochemical measurements show that FePO₄·2H₂O/MWNTs nanocomposites have a superior discharge capacity and stability. For example, FePO₄·2H₂O/MWNTs nanocomposites exhibit a high initial discharge capacity (129.9?mAhg^?1) and a stable capacity retention (114.3?mAhg^?1 after 20 cycles). The excellent electrochemical performance is attributed to the small particle size of FePO₄·2H₂O nanoparticles, the good electronic conductivity of MWNTs, and the three-dimensional conductive network structure of FePO₄·2H₂O/MWNTs nanocomposites.