Preparation of silica-magnetite nanoparticle mixed hemimicelle sorbents for extraction of several typical phenolic compounds from environmental water samples

A novel type of superparamagnetic silica-coated (Fe3O4/SiO2 core/shell) magnetite nanoparticle modified by surfactants has been successfully synthesized and was applied as an effective sorbent material for the pre-concentration of several typical phenolic compounds (bisphenol A (BPA), 4-tert-octylphenol (4-OP) and 4-n-nonylphenol (4-NP)) from environmental water samples. Compared with pure magnetic particles, a thin and dense silica layer would protect the iron oxide core from leaching out in acidic conditions. In order to enhance their adsorptive tendency towards organic compounds, cetylpyridinium chloride (CPC) or cetyltrimethylammonium bromide (CTAB) were added, which adsorbed on the surface of the Fe3O4/SiO2 nanoparticles (Fe3O4/SiO2 NPs) and formed mixed hemimicelles. Main factors affecting the adsolubilization of analytes were optimized and comparative study on the use of CPC and CTAB-coated Fe3O4/SiO2 NPs mixed hemimicelles-based SPE was also carried out. CPC-coated Fe3O4/SiO2 NPs system was selected due to lower elution volume required and more effective adsorption of the target compounds. Under selected conditions, concentration factor of 1600 was achieved by using this method to extract 800 mL of different environmental water samples. The detection limits obtained for BPA, 4-OP and 4-NP with HPLC-FLD were 7, 14, and 20 ng/L, respectively.     

Metabolic profiling of major vitamin D metabolites using Diels–Alder derivatization and ultra-performance liquid chromatography–tandem mass spectrometry

Biologically active forms of vitamin D are important analytical targets in both research and clinical practice. The current technology is such that each of the vitamin D metabolites is usually analyzed by individual assay. However, current LC-MS technologies allow the simultaneous metabolic profiling of entire biochemical pathways. The impediment to the metabolic profiling of vitamin D metabolites is the low level of 1α,25-dihydroxyvitamin D₃ in human serum (15–60 pg/mL). Here, we demonstrate that liquid–liquid or solid-phase extraction of vitamin D metabolites in combination with Diels–Alder derivatization with the commercially available reagent 4-phenyl-1,2,4-triazoline-3,5-dione (PTAD) followed by ultra-performance liquid chromatography (UPLC)–electrospray/tandem mass spectrometry analysis provides rapid and simultaneous quantification of 1α,25-dihydroxyvitamin D₃, 1α,25-dihydroxyvitamin D₂, 24R,25-dihydroxyvitamin D₃, 25-hydroxyvitamin D₃ and 25-hydroxyvitamin D₂ in 0.5 mL human serum at a lower limit of quantification of 25 pg/mL. Precision ranged from 1.6–4.8 % and 5–16 % for 25-hydroxyvitamin D₃ and 1α,25-dihydroxyvitamin D₃, respectively, using solid-phase extraction. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Electrochemical deposition of platinum nanoparticles in multiwalled carbon nanotube–Nafion composite for methanol electrooxidation

Platinum nanoparticles were successfully deposited within a multiwalled carbon nanotube (MWCNT)–Nafion matrix by a cyclic voltammetry method. A Pt(IV) complex was reduced to platinum nanoparticles on the surface of MWCNTs. The resulting Pt nanoparticles were characterized by scanning electron microscopy, transmission electron microscopy, and energy-dispersive X-ray spectroscopy. The Pt–MWCNT–Nafion nanocomposite film-modified glassy carbon electrode had a sharp hydrogen desorption peak at about −0.2 V vs. Ag/AgCl (3 M) in a solution of 0.5 M H₂SO₄, which is directly related to the electrochemical activity of the Pt nanoparticles presented on the surface of MWCNTs. The electrocatalytic properties of the Pt–MWCNT–Nafion nanocomposite-modified glassy carbon electrode for methanol electrooxidation were investigated by cyclic voltammetry in a 2 M CH₃OH + 1 M H₂SO₄ solution. In comparison with the Pt-coated glassy carbon electrode and the Pt–Nafion modified glassy carbon electrode, the Pt–MWCNT–Nafion-modified electrode had excellent electrocatalytic activity toward methanol electrooxidation. The stability of the Pt–MWCNT–Nafion nanocomposite-modified electrode had also been evaluated.     

Analytical prospect of compact disk technology in immunosensing

A sensitive and versatile methodology involving recordable compact disks as molecular screening surfaces and a standard optical CD/DVD drive as detector, is reported. Quantitative immunoanalysis, in microarray format, of a cancer marker (alpha-fetoprotein, AFP) and a selective herbicide (atrazine) on four types of audio-video disc was conducted. Enzyme or gold nanoparticle-labeled antibodies were used as tracers, forming a precipitate on the sensing disk surface. The principle of disk reading is based on capture of analog signals with the disk drive that were proportional to the darkness of the immunoreaction product. Detection limits for AFP (8.0 μg L⁻¹) and for atrazine (0.04 μg L⁻¹) were under the threshold needed to detect nonseminomatous testicular cancer, and below the maximum E.U. residue limit for drinking water, respectively. The described methodology improves the previous developments using CDs and highlights the enormous potential of immunoassay methods using standard audio–video disk surfaces in combination with the CD/DVD drive for clinical analysis, drug discovery, or high-throughput multiresidue screening applications. Figure  Eye-catching image The analytical potential of commercial audio–video discs as molecular screening surfaces in combination with use of a standard CD/DVD drive as detector for quantitative immunoanalysis of a cancer marker and agrochemical residues is demonstrated.     

Preconcentration of atrazine and simazine with multiwalled carbon nanotubes as solid-phase extraction disk

A sensitive and selective preconcentration method using solid-phase extraction (SPE) disk, namely multiwalled carbon nanotubes (MWCNTs) disk, is proposed for the determination of atrazine and simazine in water samples. Atrazine and simazine were extracted on MWCNTs disk and then determined by gas chromatography–mass spectrometry (GC/MS). Several parameters on the enrichment factor of the analytes were investigated. The experimental results showed that it was possible to obtain quantitative analysis when the solution pH was 5 using 200 mL of validation solution containing 0.1 μg of triazines and 5 mL of acetone as an eluent. The maximum enrichment factors for atrazine and simazine were 3900 ± 250 and 4000 ± 110, respectively when 200 mL of sample solution volume was used. Relative standard deviations for seven determinations were 6.9% (atrazine) and 3.0% (simazine) under optimum conditions. The linear range of calibration curves were 0.1 to 1 ng mL^{− 1} for each analyte with good correlation coefficients. The detection limits (3S/N) were 2.5 and 5.0 pg mL^{− 1} for atrazine and simazine, respectively. The proposed method was successfully applied to the determination of atrazine and simazine in environmental water samples with high precision and accuracy.     

Solid-phase microfibers based on polyethylene glycol modified single-walled carbon nanotubes for the determination of chlorinated organic carriers in textiles

Based on polyethylene glycol modified single-walled carbon nanotubes, a novel sol–gel fiber coating was prepared and applied to the headspace microextraction of chlorinated organic carriers (COCs) in textiles by gas chromatography-electron capture detection. The preparation of polyethylene glycol modified single-walled carbon nanotubes and the sol–gel fiber coating process was stated and confirmed by infrared spectra, Raman spectroscopy, and scanning electron microscopy. Several parameters affecting headspace microextraction, including extraction temperature, extraction time, salting-out effect, and desorption time, were optimized by detecting 11 COCs in simulative sweat samples. Compared with the commercial solid-phase microextraction fibers, the sol–gel polyethylene glycol modified single-walled carbon nanotubes fiber showed higher extraction efficiency, better thermal stability, and longer life span. The method detection limits for COCs were in the range from 0.02 to 7.5 ng L⁻¹ (S/N = 3). The linearity of the developed method varied from 0.001 to 50 μg L⁻¹ for all analytes, with coefficients of correlation greater than 0.974. The developed method was successfully applied to the analysis of trace COCs in textiles, the recoveries of the analytes indicated that the developed method was considerably useful for the determination of COCs in ecological textile samples.     

Evaluation of carbon nanocones/disks as sorbent material for solid-phase extraction

The potential of carbon nanocones/disks as sorbent material in solid-phase extraction (SPE) procedures has been evaluated. For this aim, a model analytical problem, the determination of chlorophenols in water samples, was selected. An accurately weighed amount of 20 mg of purified carbon nanocones/disks was packed in 3 mL commercial SPE cartridges. Once conditioned, up to 8 mL of water samples can be preconcentrated without analyte losses. The chlorophenols were eluted by using 200 μL of hexane. Aliquots of 2 μL of the organic extract were injected in the gas chromatograph–mass spectrometer for separation and quantification. The purification of the commercial nanocones/disks to reduce the presence of amorphous carbon has been successfully achieved by heating the carbon nanocones/disks at 450 °C for 20 min. Detection limits of chlorophenols were in the range 0.3–8 ng mL⁻¹ by using 2 mL of sample. Moreover, excellent average recovery values (98.8–100.9%) have been obtained after the analysis of water samples from different nature. Finally, the performance of the carbon nanocones/disks as sorbent material has been compared with that of multiwalled carbon nanotubes, providing the former better results under the experimental conditions assayed.     

Determination of 11 priority pollutant phenols in wastewater using dispersive liquid—liquid microextraction followed by high-performance liquid chromatography—diode-array detection

Dispersive liquid—liquid microextraction coupled with high-performance liquid chromatography—diode-array detection was applied for the extraction and determination of 11 priority pollutant phenols in wastewater samples. The analytes were extracted from a 5-mL sample solution using a mixture of carbon disulfide as the extraction solvent and acetone as the dispersive solvent. After extraction, solvent exchange was carried out by evaporating the solvent and then reconstituting the residue in a mixture of methanol–water (30:70). The influences of different experimental dispersive liquid—liquid microextraction parameters such as extraction solvent type, dispersive solvent type, extraction and dispersive solvent volume, salt addition, and pH were studied. Under optimal conditions, namely pH 2, 165-μL extraction solvent volume, 2.50-mL dispersive solvent volume, and no salt addition, enrichment factors and limits of detection ranged over 30–373 and 0.01–1.3 μg/L, respectively. The relative standard deviation for spiked wastewater samples at 10 μg/L of each phenol ranged between 4.3 and 19.3% (n = 5). The relative recovery for wastewater samples at a spiked level of 10 μg/L varied from 65.5 to 108.3%.     

Measurement of bisphenol A, bisphenol A ß-D-glucuronide, genistein, and genistein 4'-ß-D-glucuronide via SPE and HPLC-MS/MS

Bisphenol A (BPA) is a synthetic industrial reactant used in the production of polycarbonate plastics, and genistein is a natural phytoestrogen abundant in the soybean. Current studies investigating the endocrine-disrupting effects of concomitant exposures to BPA and genistein have warranted the development of an analytical method for the simultaneous measurement of BPA and genistein, as well as their primary metabolites, bisphenol A ?-d-glucuronide (BPA gluc) and genistein 4′-?-d-glucuronide (genistein gluc), respectively. All four analytes were extracted from rat plasma via solid phase extraction (SPE). Three SPE cartridges and four elution schemes were tested. Plasma extraction using Bond Elut Plexa cartridges with sequential addition of ethyl acetate, methanol, and acetonitrile yielded optimal average recoveries of 98.1 ± 1.8% BPA, 94.9 ± 8.0% genistein, 91.4 ± 6.1% BPA gluc, and 103 ± 6.1% genistein gluc. Identification and quantification of the four analytes were performed by a validated HPLC-MS/MS method using electrospray ionization and selective reaction monitoring. This novel analytical method should be applicable to the measurement of BPA, genistein, BPA gluc, and genistein gluc in urine, cultures, and tissue following in vivo exposures. While reports of the determination of BPA and genistein independently exist, the simultaneous optimized extraction and detection of BPA, genistein, BPA gluc, and genistein gluc have not previously been reported.     

Transfer of bisphenol A from thermal printer paper to the skin

Of 13 thermal printing papers analyzed, 11 contained 8–17 g/kg bisphenol A (BPA). When taking hold of a receipt consisting of thermal printing paper for 5 s, roughly 1 μg BPA (0.2–6 μg) was transferred to the forefinger and the middle finger if the skin was rather dry and about ten times more if these fingers were wet or very greasy. This amount transferred to dry skin was neither significantly increased when taking hold of the paper at up to 10 sites, nor reduced when BPA-free paper was contacted afterwards. After 60–90 min, BPA applied to the skin as a solution in ethanol was only partially or no longer at all extractable with ethanol, whereas BPA transferred to the skin by holding thermal printer paper remained largely extractable after 2 h. This suggests that penetration of the skin depends on the conditions. Extractability experiments did not enable us to conclude whether BPA passes through the skin, but indicated that it can enter the skin to such a depth that it can no longer be washed off. If this BPA ends up in the human metabolism, exposure of a person repeatedly touching thermal printer paper for 10 h/day, such as at a cash register, could reach 71 μg/day, which is 42 times less than the present tolerable daily intake (TDI). However, if more than just the finger pads contact the BPA-containing paper or a hand cream enhances permeability of the skin, this margin might be smaller.     

Characterization of a titanium(IV)–porphyrin complex as a highly sensitive and selective reagent for the determination of hydrogen peroxide: a computational chemistry approach and a critical review

The Ti–TPyP reagent, i.e. an acidic aqueous solution of the oxo[5,10,15,20-tetra(4-pyridyl)porphyrinato] titanium(IV) complex, TiO(tpyp), was developed as a highly sensitive and selective spectrophotometric reagent for determination of traces of hydrogen peroxide. Using this reagent, determination of hydrogen peroxide was performed by flow-injection analysis with a detection limit of 0.5 pmol per test. The method was actually applied to determination of several constituents of foods, human blood, and urine mediated by appropriate oxidase enzymes. The reaction specificity of the TiO(tpyp) complex for hydrogen peroxide was clarified from the viewpoint of the reaction mechanisms and molecular orbitals based on ab initio calculations. The results provided a well-grounded argument for determination of hydrogen peroxide using the Ti–TPyP reagent experimentally. This review deals with characterization of the high sensitivity and reaction specificity of the Ti–TPyP reagent for determination of hydrogen peroxide, to prove its reliability in analytical applications. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Automated on-line liquid chromatography-photodiode array-mass spectrometry method with dilution line for the determination of bisphenol A and 4-octylphenol in serum

A novel on-line liquid chromatography-photodiode array detection-mass spectrometry (LC-DAD-MS) system was established with restricted-access media (RAM) pre-column and dilution line combined with a column-switching valve. The serum samples were injected directly onto pre-column under diluted condition by dilution line. After elution of proteins in the serum, the analytes were backflushed onto an ODS analytical column using a six-port column-switching device. The influence of the composition of the mobile phase, for instance, organic modifer, ionic strength, pH, dilution times and the rotation time of the switching valve have been investigated using bisphenol A (BPA) and 4-octyphenol (4-OP) as analytes. The evaluations for peak responses and sensitivity were conducted by MS, and proteins were removed by RAM-column with DAD monitoring at 280 nm. The peak shape was improved by adding a dilution line, especially in the case of large volume injection (LVI), which increased the sensitivity of the analysis. The selective and sensitive quantification of BPA and 4-OP in serum sample could be finished within 25 min. The method had linearity in the range 0.1-500 ng/mL with a limit of quantification for BPA and 4-OP of 0.1 and 0.5 ng/mL, respectively. The recoveries were in the range of 80-101% with less than 9.0% RSDs. This on-line LC-MS method demonstrates potential application to evaluating the exposure and risk of BPA and 4-OP in human.     

Determination of alkylphenols and 17β-estradiol in fish homogenate. Extraction and clean-up strategies

The determination of target analytes such as nonyl- and octylphenols and 17β-estradiol in fish homogenate require of solid–liquid extraction step. In this work microwave-assisted extraction (MAE) and focused-ultrasound liquid extraction (FUSLE) were studied as two different alternatives for extraction of the target compounds in zebrafish (Danio rerio) homogenate. In this work solid phase extraction (SPE) using 5-g and 10-g Florisil cartridges and gel permeation chromatography (GPC) were studied for the clean-up of the MAE and FUSLE extracts due to the non-selective extraction step. Although good recoveries were obtained both for SPE (106% and 126% range) and GPC (79% and 100% range) clean-up procedures, cleaner chromatograms were obtained after SPE and finally 5-g Florisil cartridges were tested since no improvement was observed when 10-g Florisil cartridges were used. Under optimized clean-up conditions, MAE and FUSLE provided comparable results for 4nOP and NP, while more accurate results were obtained for 4tOP and E2 after FUSLE. Finally, the method was applied to the determination of alkylphenols and 17β-estradiol in zebrafish homogenate that had been exposed to known concentrations of the target analytes. In the case of alkylphenols two different isomers of nonyl- and octylphenol (4-(3′,6′-dimethyl-3′-hepthyl)phenol, 363-NP, and 4-(3′-methyl-3′-hepthyl)phenol, 33-OP) were studied.     

Preparation and electrochemical performance of activated carbon thin films with polyethylene oxide-salt addition for electrochemical capacitor applications

The effect of polymer–salt addition in the activated carbon electrode for electric double-layer capacitor (EDLC) has been investigated. A series of composite thin film electrode consisting of activated carbon, carbon black, polytetrafluoroethylene and polymer–salt complex (polyethyleneoxide–LiClO₄) with an appropriate weight ratio were prepared and examined their performance for EDLCs using 1 mol L⁻¹ LiClO₄ in ethylene carbonate:diethylcarbonate electrolyte solution. The electrochemical capacitance performances of these electrodes with different compositions were characterized by cyclic voltammetry, galvanostatic charge–discharge cycling, and AC impedance measurements. By comparison, the best results were obtained with a composite electrode rich in polymer–salt additive (132 F g⁻¹ at 100 mA g⁻¹ of galvanostatic experiment). In general, the polymer–salt-containing electrode had shown improved performance over activated carbon electrodes without polymer–salt at high current density.     

Pseudocapacitive behaviors of nanostructured manganese dioxide/carbon nanotubes composite electrodes in mild aqueous electrolytes: effects of electrolytes and current collectors

Nanostructured MnO₂/carbon nanotubes composite electrode material was prepared using the liquid-phase deposition reaction starting with potassium permanganate (KMnO₄) and manganese acetate (Mn(Ac)₂·4H₂O) as the reactants and carbon nanotubes (CNTs) as the substrates. The structure and morphology of the material was characterized by X-ray diffraction, infrared spectroscopy, and transmission electron microscope techniques. The electrochemical properties of the nano-MnO₂/CNTs composite electrode in 1 M LiAc and 1 M MgSO₄ solutions and in 1 M RAc (R = Li, Na, and K)–1 M MgSO₄ mixed solutions, respectively, were studied. Experimental results demonstrated that the specific capacitance and rate discharge ability of the nano-MnO₂/CNTs composite electrode in 1 M LiAc–1 M MgSO₄ mixed solution is superior to that in 1 M LiAc or 1 M MgSO₄ solution. For the 1 M RAc (R = Li, Na, and K)–1 M MgSO₄ mixed electrolytes, the specific capacitance of the composite electrode was found to be in the following order: LiAc > NaAc > KAc.     

Determination of synthetic polycyclic musks in aqueous samples by ultrasound-assisted dispersive liquid-liquid microextraction and gas chromatography-mass spectrometry

A simple and solvent-minimized procedure for the determination of six commonly found synthetic polycyclic musks in aqueous samples using ultrasound-assisted dispersive liquid–liquid microextraction (UA-DLLME) coupled with gas chromatography–mass spectrometry (GC-MS) is described. The parameters affecting the extraction efficiency of analytes from water samples were systematically investigated. The best extraction conditions involved the rapid injection of a mixture of 1.0 mL of isopropyl alcohol (as a dispersant) and 10 μL of carbon tetrachloride (as an extractant) into 10 mL of water containing 0.5 g of sodium chloride in a conical-bottom glass tube. After ultrasonication for 1.0 min and centrifugation at 5,000 rpm (10 min), the sedimented phase 1.0 μL was directly injected into the GC-MS system. The limits of quantitation (LOQs) were less than 0.6 ng/L. The precision for these analytes, as indicated by relative standard deviations (RSDs), was less than 11% for both intra- and interday analysis. Accuracy, expressed as the mean extraction recovery, was between 71 and 104%. Their total concentrations were determined in the range from 8.3 to 63.9 ng/L in various environmental samples by using a standard addition method.     

Passive sampling and stir bar sorptive extraction for the determination of endocrine-disrupting compounds in water by GC-MS

A new method using the extraction and preconcentration capabilities of stir bar sorptive extraction, combined with high-resolution gas chromatography and mass spectrometry, was developed for the determination of five selected endocrine-disrupting compounds (4-n-nonylphenol, bisphenol A, estrone, 17β-estradiol, and 17α-ethinylestradiol) in water. In situ derivatization to transform the phenolic compounds into lipophilic and volatile analytes was carried out with acetic anhydride. Two different methods of headspace derivatization to further improve the chromatographic properties of 17β-estradiol and 17α-ethinylestradiol were developed and compared. The optimized method provided good sensitivity (limits of quantitation 1.2–2.6 ng), repeatability (relative standard deviation 2–9%), and reproducibility (relative standard deviation 10–17%). Passive sampling by means of polar organic chemical integrative samplers was applied to monitor river waters used as supply sources for drinking water treatment plants in the Liguria region of Italy. The analytes showed a different distribution at the three sites considered; bisphenol A proved to be the most abundant, ranging from 185 to 459 ng per sampler.     

Determination of 252–302 Da and tentative identification of 316–376 Da polycyclic aromatic hydrocarbons in Standard Reference Materials 1649a Urban Dust and 1650b and 2975 Diesel Particulate Matter by accelerated solvent extraction–HPLC-GC-MS

We have assessed and compared the extraction recoveries of polycyclic aromatic hydrocarbons (PAHs) with molecular weights of 252, 276, 278, 300 and 302 from diesel particulate matter (PM) and urban air particles using ultrasonically assisted extraction and accelerated solvent extraction methods, and evaluated the effects of sample and treatment parameters. The results show that accelerated solvent extraction can extract PAHs more efficiently from diesel PM than ultrasonically assisted extraction. They also show that PAHs are more difficult to extract from diesel PM than from urban air particles. Using toluene and maximum instrumental settings (200 °C, 3,000 psi and five extraction cycles) with 30-min static extraction times > 85% of the analytes were estimated to be extracted from the diesel particles, but four extraction cycles with just 5-min static extraction times under these conditions seem to be sufficient to extract > 95% of the analytes from the urban air particles. The accelerated solvent extraction method was validated using the Standard Reference Materials (SRM) 1649a, Urban Dust, and SRM 2975 and SRM 1650a, Diesel Particulate Matter, from the US National Institute of Standards and Technology (NIST). PAH concentrations determined by on-line high-performance liquid chromatography–gas chromatography–mass spectrometry (HPLC-GC-MS) following the developed accelerated solvent extraction method were generally higher than the certified and reference NIST values and concentrations reported in the literature (e.g. the estimated concentration of benzo[a]pyrene in SRM 2975 was 15-fold higher than the NIST-certified value), probably because the extraction recoveries were higher than in previous studies. The developed accelerated solvent extraction method was used to analyse high molecular (HMW) weight PAHs (MW > 302) in the investigated SRMs, and more than 170 (SRM 1649a), 80 (SRM 1650b) and 60 (SRM 2975) potential high molecular weight PAHs were tentatively identified in them, with molecular weights (depending on the SRM sample analysed) of 316, 326, 328, 340, 342, 350, 352, 366, 374 and 376. This is, to our knowledge, the first study to tentatively report PAHs with molecular weights of 316, 326, 328, 342, 350, 352, 366 and 376 in diesel particulate matter. GC-MS chromatograms obtained in selected ion monitoring mode (extracted ions for the abovementioned m/z) and full-scan mass spectra of tentatively identified high molecular weight PAHs are shown in the Electronic supplementary material. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

FAD-modified SiO2/ZrO2/C ceramic electrode for electrocatalytic reduction of bromate and iodate

SiO₂/ZrO₂/C carbon ceramic material with composition (in wt%) SiO₂ = 50, ZrO₂ = 20, and C = 30 was prepared by the sol–gel-processing method. A high-resolution transmission electron microscopy image showed that ZrO₂ and the graphite particles are well dispersed inside the matrix. The electrical conductivity obtained for the pressed disks of the material was 18 S cm⁻¹, indicating that C particles are also well interconnected inside the solid. An electrode modified with flavin adenine dinucleotide (FAD) prepared by immersing the solid SiO₂/ZrO₂/C, molded as a pressed disk, inside a FAD solution (1.0 × 10⁻³ mol L⁻¹) was used to investigate the electrocatalytic reduction of bromate and iodate. The reduction of both ions occurred at a peak potential of −0.41 V vs. the saturated calomel reference electrode. The linear response range (lrr) and detection limit (dl) were: BrO₃ ⁻, lrr = 4.98 × 10⁻⁵–1.23 × 10⁻³ mol L⁻¹ and dl = 2.33 μmol L⁻¹; IO₃ ⁻, lrr = 4.98 × 10⁻⁵ up to 2.42 × 10⁻³ and dl = 1.46 μmol L⁻¹ for iodate.     

Liquid–solid disk extraction followed by supercritical fluid elution and gas chromatography of phenols from water

A method combining the techniques of liquid – solid disk extraction (LSDE) and supercritical fluid elution (SFE) has been developed for the phenols regulated by the Clean Water Act. LSDE uses a disk or membrane made of polytetrafluoroethylene (PTFE) fibrils impregnated with small particles, e.g. styrene divinylbenzene (SDB) resin, to extract phenols from water. After disk extraction the retained analytes are eluted from the disk using SFE. SFE is used as an alternative to liquid solvent elution with an organic solvent. Analytes are separated, identified, and quantified using gas chromatography – ion trap detector mass spectrometry (GC-ITDMS). The method is capable of sub parts per billion detection limits, and precision of 5–28% RSD. Evaluation of various disks or membranes, such as C₁₈-silica disks, SDB disks, and ion exchange membranes, has also been performed for the extraction of phenols from water. The results obtained from the in-situ aqueous acetylation of phenols and extraction of their acetates are quantitative. The utilization of LSDE and SFE techniques has proven to be a more effective approach than liquid – liquid extraction in minimizing air pollution and solvent waste.