A comparison of INAA and ICP-MS/ICP-AES methods for the analysis of meteorite samples

Instrumental neutron activation analysis (INAA), inductively coupled plasma atomic emission spectrometry (ICP-AES) and ICP mass spectrometry (ICP-MS) (hereafter, ICPs) were applied to meteorite samples for the determination of elemental content. The analytical applicability and suitability of the three methods have been compared. Those comparisons led to the refinement of our analytical procedures for INAA and ICPs, yielding more reliable data. Our INAA data proved to be reliable enough for classifying meteorites, while the ICPs, especially ICP-MS, can characterize elemental abundance features in detail, as demonstrated by REE abundance patterns for the Allende meteorite. In this manner, INAA and ICPs can be used in a complementary fashion in cosmochemical studies.     

A comparison between INAA and ICP-MS for the determination of element concentrations in marine sediments

In this study, instrumental neutron activation analysis (INAA) and inductively coupled plasma-mass spectrometry (ICP-MS) were used to compare results obtained by both techniques for sediment samples collected from the Patras Harbour, Western Greece. The accuracy of the methods was tested using reference materials. In total seven elements were measured by both techniques (Zn, Ni, Cr, Ba, As, U, Co). Results obtained by ICP-MS were compared with those obtained by INAA by applying paired t-test. Insignificant differences in mean concentration values were found for Zn, Ni, Cr and Ba, whereas the differences for As, Co and U were significant. Correlations between element concentrations measured by both techniques are also discussed.     

Trace element analysis of turkey vulture (Cathartes aura) feathers

Ten feather samples, including primary and secondary flight and tail feathers, were analysed for the trace element composition of vane and rachis structures using instrumental neutron activation analysis (INAA), inductively coupled plasma-mass spectrometry (ICP-MS), and cold vapour atomic absorption spectroscopy (CVAAS). Five environmentally significant elements, Cr, As, Se, Sb and Hg, were analysed by INAA and ICP-MS/CVAAS. A further seventeen elements were analysed by ICP-MS. The majority data obtained by INAA and ICP-MS/CVAAS were not statistically significantly different (p = 0.05), although the removal of isobaric interferences using dynamic reaction cell technology was essential to produce ICP-MS data that were consistent with INAA for Cr, As and Se. Significantly higher trace element concentrations were observed for vane relative to rachis for all elements, except Cu and Hg. These elements displayed vane/rachis ratios of 0.7 ± 0.2 and 1.0 ± 0.2, respectively. In general, vane and rachis subgroups afforded data that were consistent with a normal distribution, with RSDs in the range (12–83) % for INAA analyses. A total of 18 outliers were noted amongst the various feather, structure, element combinations, with 14 outliers being observed in the vane and/or rachis structures of the same tail feather. Given the significant differences in vane and rachis concentrations observed for many elements, the large RSDs reported for elements and the potential for outliers, the determination of environmental trace element burden using feathers is significantly enhanced by the analysis of multiple feathers using INAA.     

Sequential multielement analysis of a single aerosol filter by different instrumental and wet-chemical methods

Summary The direct instrumental methods X-ray fluorescence spectrometry (XRFS) and instrumental neutron activation analysis (INAA), and, after digestion of the sample, inductively coupled plasma mass spectrometry (ICP-MS) were applied in sequence to analyse small single aerosol filters. XRFS detected up to 19, INAA up to 22, and ICP-MS up to 33 elements. In total, up to 45 elements were determined, and, for a number of additional elements limits of detection could be given. For many elements, the data quality could be checked by cross-comparison of the results of two or all three methods. These methods very meaningfully complement each other and, in the manner used, allow the determination of all elements of interest in a small aerosol filter sample.     

Application of instrumental neutron activation analysis and inductively coupled plasma-mass spectrometry to studying the river pollution in the State of Minas Gerais

Instrumental neutron activation analysis (INAA) and inductively coupled plasma-mass spectrometry (ICP-MS) have been used for the determination of toxic heavy metals and other pollutants in the water of the Das Velhas river in the State of Minas Gerais, in south-east Brazil. Elemental concentrations of about 60 elements were measured in water samples collected to different parts of this river and from two affluents. There was a good agreement between the two analytical methods and the results were complementary. The results indicated an increase in the concentration of several polluting elements in the water from mining industry area.     

Quality Control in Element Analysis of Plant Materials

A worldwide laboratory intercomparison was organized by the International Atomic Energy Agency's Analytical Quality Control Services (AQCS) involving the determination of elements in plant materials used for human consumption. The main purpose of this work was to evaluate the performance of our analytical methods including sample preparation and to obtain new reference materials that can be used in our further work. Both materials (spinach and cabbage) were analyzed by inductively coupled plasma atomic emission spectrometry (ICP-AES) and instrumental neutron activation analysis (INAA). Six subsamples of each material were subjected to our digestion procedure and the solutions were measured by ICP-AES. The dried samples were analyzed using INAA. Up to 26 elements were determined in plant materials. For easy review of our data a score has been calculated based on the reference value for each measured element. According to our results the ICP-AES technique was useful for determination of the following elements: Ba, Ca, Cr, Fe, K, Mn, Mo, P, S, Sr, Ti. The INAA method was reliable for measurement of Ce, Co, Mn, Na, Rb, Th, and V.     

Multielement determination and speciation of major-to-trace elements in black tea leaves by ICP-AES and ICP-MS with the aid of size exclusion chromatography.

A multielement determination of major-to-trace elements in black tea leaves and their tea infusions was carried out by ICP-AES (inductively coupled plasma atomic emission spectrometry) and ICP-MS (inductively coupled plasma mass spectrometry). Tea infusions were prepared as usual tea beverage by brewing black tea leaves in boiling water for 5 min. About 40 elements in tea leaves and tea infusions could be determined over the wide concentration range in 8 orders of magnitude. The extraction efficiency of each element was estimated as the ratio of its concentration in tea infusions to that in tea leaves. From the experimental results for the extraction efficiencies, the elements in black tea leaves were classified into three characteristic groups: (i) highly-extractable elements (>55%): Na, K, Co, Ni, Rb, Cs and Tl, (ii) moderately-extractable elements (20-55%): Mg, Al, P, Mn and Zn, and (iii) poorly-extractable elements (<20%): Ca, Fe, Cu, Sr, Y, Zr, Mo, Sn, Ba and lanthanoid elements. Furthermore, speciation of major-to-trace elements in tea infusions was performed by using a combined system of size exclusion chromatography (SEC) and ICP-MS (or ICP-AES). As a result, many diverse elements were found to be present as complexes associated with large organic molecules in tea infusions.     

Determination of Elements in Japanese Standard Soil Materials by Means of Insturmental Neutron Activation Analysis

Instrumental neutron activation analysis (INAA), and inductively coupled plasma mass spectroscopy (ICP-MS) were applied to the determination of major elements and rare earth elements in Japanese Standard Soil Materials (NDG-1 to -8). Eight major elements, Al, Fe, Ti, Ca, Mg, Mn, K, and Na were determined by INAA. A comparison of the data for rare earth elements obtained by INAA and ICP-MS shows that the data of the contents determined by the two different analytical methods are in fairly good agreement with each other.     

On-line coupling of ion chromatography and atomic spectrometry and use of direct graphite furnace atomic absorption spectrometry as new tools for ultra trace determinations in refractory metals

On-line coupling of inductively coupled plasma (ICP) techniques such as ICP-AES and ICP-MS with ion chromatography (IC) offers unique features for ultra-trace analysis. An on-line preconcentration procedure based on cation exchange enables sub-ng/g analysis in complex matrices like molybdenum and tungsten. The best dissolution reagent for these matrices is hydrogen peroxide, which can be cleaned to ultra high purity with the same metal free chromatography equipment used for the preconcentration. Preconcentration is possible for elements that show cationic reactions within acidic peroxide containing solutions. In this study 28 elements detrimental for microelectronics applications are observed. A comparison of the combinations IC-ICP-AES and IC-ICP-MS with glow discharge mass spectrometry (GDMS) for the analysis of today's purest tungsten samples shows the analytical power and accuracy of the coupled devices. Graphite furnace atomic absorption spectrometry (GFAAS) as an extremely sensitive analytical technique is applied with and without the same sample pretreatment as used for the on-line coupling. Direct GFAAS measurements of alkali metals are complementary to IC-ICP techniques. The data evaluated with these wet chemical techniques are compared to the usual manufacturers characterisation technique GDMS. With respect to the low concentrations present in these high purity materials (ng/g level in the solid) the discrepancies between all methods are acceptable. The sensitivity of IC-ICP-MS is in most cases far superior to IC-ICP-AES and for some elements also to GDMS. Furthermore the specific advantages of on-line coupling such as the elimination of isobaric interferences in ICP-MS or spectral interferences in ICP-AES are shown for ICP-AES and ICP-MS determinations.     

Analysis of germanium and germanium dioxide samples by mass-spectrometry and atomic emission spectroscopy

Three multielement methods: (1) inductively coupled plasma mass spectrometry (ICP-MS), (2) inductively coupled plasma atomic emission spectroscopy (ICP-AES), and (3) spark source mass spectrometry (SSMS) were used for the determination of additives in the samples of germanium and germanium oxide. The detection limits of direct SSMS and ICP-AES/ICP-MS were compared using the autoclave predissolution of germanium and germanium dioxide samples. It was shown that in the latter case, the detection limits could be significantly improved by the separation of germanium from analytes by distillation. In this case, the detection limits of such limiting elements like Th and U can reach the level n 10^?10 wt %.     

Determination of Heavy Metals in Soils, Sediments and Geological Materials by ICP-AES and ICP-MS

 Sixteen soil and sedimentary geological reference materials were analysed for As and the heavy metals Cd, Co, Cr, Cu, Ni, Pb and Zn by inductively coupled plasma-atomic emission spectrometry (ICP-AES) and inductively coupled plasma-mass spectrometry (ICP-MS) in combination with total and partial dissolution of the samples. It can be demonstrated that none of the modern ICP methods is completely free from analytical problems. This applies in particular when the concentrations are close to the detection limits (e.g. in ICP-AES) and is mainly due to the wide variation in the bulk composition of soils resulting in complex matrix effects (e.g. in ICP-MS). In order to determine the extent of soil pollution by heavy metals, both partial and total dissolution have to be performed prior to analysis.     

Polynomial mass bias functions for the internal standardization of isotope ratio measurements by multi-collector inductively coupled plasma mass spectrometry

The development and application of a calibration strategy for routine isotope ratio analysis by multi-collector inductively coupled plasma mass spectrometry (ICP-MS) is described and assessed. Internal standardization was used to account for the mass dependant determinate error (mass bias). The general solution for polynomial isotope ratio mass bias functions for use with internal standardization and isotope ratio measurements by multi-collector inductively coupled plasma mass spectrometry was derived. The resulting linear isotope ratio mass bias function was demonstrated to be mathematically consistent and experimentally realistic for the analysis of acidified aqueous solutions of analyte and internal standard elements (clean solutions) by multi-collector inductively coupled plasma mass spectrometry.     

Comparison of inductively coupled plasma-atomic emission spectrometry, anodic stripping voltammetry and instrumental neutron-activation analysis for the determination of heavy metals in airborne particulate matter

The capability of three analytical techniques, inductively coupled plasma-atomic emission spectrometry (ICP-AES), anodic stripping voltammetry (ASV), and instrumental neutron-activation analysis (INAA) have been compared for the determination of Cd, Fe, Pb, and Zn in airborne particulate matter, collected on cellulose filters, from the atmosphere of the large area of Thessaloniki, Greece. Two procedures were tested for quantitative leaching of these elements from the filters before ICP-AES and ASV, digestion with aqua regia in a Teflon autoclave, after dissolution of the organic matter with HClO4 under ambient conditions, and ultrasonic extraction with a mixture of HNO3 and HCl. Validation of the leaching and digestion procedures revealed that digestion in the autoclave is more effective, especially for Fe. The concentrations of these elements over a decade in both industrial and urban areas of the investigated region are compared.     

Study on the retention of uranyl ions on modified clays with titanium oxide

Four analytical techniques—instrumental neutron activation analysis (INAA), inductively coupled plasma mass spectrometry (ICP-MS), scanning electron microscope energy dispersive X-ray fluorescence (SEM-EDXRF), and proton induced X-ray emission (PIXE)—were evaluated in the context of air pollution biomonitoring studies. Three combinations INAA/ICP-MS, ICP-MS/PIXE and ICP-MS/SEM-EDXRF are illustrated by experimental results.     

萤石成分分析方法的标准现状与研究进展

萤石是一种重要的战略性非金属矿产资源,本文对中国国家标准、行业标准、国际标准（ISO）、美国标准（ASTM）以及俄罗斯标准（GOST）中的萤石成分分析标准方法的现状进行了介绍。对近年来X射线荧光光谱法（XRF）、电感耦合等离子体发射光谱法（ICP-AES）、电感耦合等离子体质谱法（ICP-MS）、激光诱导击穿光谱法（LIBS）等技术在萤石成分分析中的应用以及标准物质/标准样品研制情况进行了总结和评述。文章认为,萤石分析测试技术标准体系相对完备,XRF、ICP-AES、ICP-MS等仪器分析测试技术已普遍应用于萤石样品实验室分析,建议尽快研究并建立萤石中稀土等微量元素测定的标准方法,并开展相应标准物质/标准样品的研制,同时应大力开展原位在线分析技术的研究与开发,以适应工业在线自动化监测的需求,LIBS与在线XRF技术联合在萤石在线分析方面具有良好的应用潜力。     

Nutritional and Environmental Properties of Algal Products Used in Healthy Diet by INAA and ICP-AES

Spirulina platensis alga sampled in the Caribbean Sea and seven other commercial algal products available on the Italian market of different origin and aspect, have been analyzed by instrumental neutron activation analysis (INAA) and inductively coupled plasma-atomic emission spectrometry (ICP-AES). By neutron irradiation and -ray spectrometry (INAA), as many as 20 elements could be measured instrumentally without any chemical treatment. Cu, Mg, Mn and Pb were determined after dissolution of the sample by ICP-AES. The cross-checking of the data, specifically by comparing those of Ca, Cr, Fe and Zn, obtained by the two techniques was found to be in good agreement. Special attention from analytical and nutritional point of view has been devoted to the toxic metals. The measurements have been carried out employing the reference algal material prepared by International Atomic Energy Agency (IAEA).     

Application of ICP-MS,INAA and RNAA to the determination of some “difficult” elements in infant formulas

In this work a determination of selected elements in the infant formulas commercially available on the Polish market was done. 14 different materials (milk-based formulas and grain porridges) were analyzed. Both, inductively coupled plasma mass spectrometry (ICP-MS) and instrumental neutron activation analysis (INAA) were applied for the determination of As, Cr, Fe and Se, which are recognized as the problematic elements for ICP-MS. For As and Se, the radiochemical NAA was also used. The daily intake of Se and Fe in the age 0–6 months for non-breast fed infants was estimated and compared with present safety limits.

     

Trends in sorption preconcentration combined with noble metal determination.

Nowadays much attention is being paid to the determination of trace amounts of noble metals in geological, industrial, biological and environmental samples. The most promising techniques, such as inductively coupled plasma atomic emission spectrometry (ICP-AES), inductively coupled plasma mass spectrometry (ICP-MS) and electrothermal atomic absorption spectrometry (ETAAS) are characterized by high sensitivity. However, the accurate determination of trace noble metals has been limited by numerous interferences generated from the presence of matrix elements. To decrease, or eliminate, these interferences, the sorption preconcentration of noble metals is often used prior to their instrumental detection. A great number of hyphenated methods of noble metal determination using sorption preconcentration have been developed. This review describes the basic types of available sorbents, preconcentration procedures and preparations of the sorbent to the subsequent determination of noble metals. The specific features of instrumental techniques and examples of ETAAS, FAAS, ICP-AES, ICP-MS determinations after the sorption preconcentration of noble metals are considered. The references cited here were selected mostly from the period 1996 - 2006.     

Preparation and characterization of a set of IAEA reference air filters for quality control in air-pollution studies

Several sets of reference air filters were prepared as part of an IAEA evaluation of the performance of laboratories involved in air-pollution studies. Each set comprised three polycarbonate membrane filters, two of which were loaded with urban air particulate matter (APM) obtained in Vienna or Prague, and one unloaded filter. The filters were loaded by filtration of a suspension of the APM materials in water. The homogeneity both of bulk APM materials and of the loaded filters was evaluated and found suitable by determining several elements by instrumental neutron-activation analysis (INAA), proton-induced X-ray emission (PIXE), and micro-X-ray energy-dispersive fluorescence analysis (micro-EDXRF). After evaluation of the homogeneity, INAA, PIXE, EDXRF, atomic absorption spectrometry (AAS), inductively coupled plasma optical emission spectrometry (ICP-OES), and ICP mass spectrometry (ICP-MS) were used to characterize the filter materials and establish "target values" and their associated standard deviations for 15 elements. Problems encountered during the preparation of these unique, simulated air filters and the criteria for setting both the target values and standard deviations are presented.     

Inter-method comparison for the determination of antimony and arsenic in peat samples

Four analytical approaches, based on different physical principles, for the determination of antimony (Sb) and arsenic (As) in ancient peat samples were critically evaluated: (a) open vessel digestion/hydride generation-atomic absorption spectrometry (HG-AAS), (b) closed-pressurized digestion in a microwave oven followed by sector field-inductively coupled plasma-mass spectrometry (SF-ICP-MS), (c) digestion in a microwave autoclave and subsequent quadrupole-inductively coupled plasma-mass spectrometry (Q-ICP-MS) measurements and (d) instrumental neutron activation analysis (INAA). The quality control scheme applied, always included the use of adequate plant reference materials to ensure the accuracy and precision of the analytical procedures. Additionally, two internal peat reference materials were analyzed using all four analytical approaches, generally showing good agreement for both elements. Method detection limits for As and Sb provided by all procedures were approximately 5 and 2 ng g⁻¹ which is sufficiently low for the reliable quantification of both elements in ancient, pre-anthropogenic peat samples. A comparison of As and Sb concentrations in a set of peat samples determined by INAA, HG-AAS and SF-ICP-MS revealed that INAA underestimated the values in a systematic manner, whereas HG-AAS and SF-ICP-MS data agreed very well. Best precision of the results was obtained by analytical procedures involving HG-AAS or Q-ICP-MS and varied from 3.6 to 4.3% and 7.1 to 7.5% for As (at about 0.5 μg g⁻¹) and Sb (at about 0.1 μg g⁻¹), respectively. The highest sample throughput (40 samples per run accomplished in 2 h) combined with low risk of sample contamination could be realized in the high-pressure microwave autoclave. The amount of sample required by all approaches was 200 mg, except for INAA which needed at least 25 times more sample mass to achieve comparable detection limits. For the quantification of As and Sb, inductively coupled plasma-mass spectrometry (ICP-MS) was preferred over INAA and HG-AAS, mainly because (a) less sample is needed and (b) As and Sb can be determined simultaneously. In addition, ICP-MS offers the possibility to measure concurrently a wide range of other elements which also are of environmental interest.