Local heat transfer distribution between smooth flat surface and impinging air jet from a circular nozzle at low Reynolds numbers

An experimental investigation is performed to study the effect of jet to plate spacing and low Reynolds number on the local heat transfer distribution to normally impinging submerged circular air jet on a smooth and flat surface. A single jet from a straight circular nozzle of length-to-diameter ratio (l/d) of 83 is tested. Reynolds number based on nozzle exit condition is varied between 500 and 8,000 and jet-to-plate spacing between 0.5 and 8 nozzle diameters. The local heat transfer characteristics are obtained using thermal images from infrared thermal imaging technique. It was observed that at lower Reynolds numbers, the effect of jet to plate distances covered during the study on the stagnation point Nusselt numbers is minimal. At all jet to plate distances, the stagnation point Nusselt numbers decrease monotonically with the maximum occurring at a z/d of 0.5 as opposed to the stagnation point Nusselt numbers at high Reynolds numbers which occur around a z/d of 6.     

Heat transfer characteristics from in-line arrays of free impinging jets

An experimental investigation of the convective heat transfer on a flat surface in a multiple-jet system is described. A thin metal sheet was heated electrically and cooled from one side. On the other black coated side the temperature field was measured using an IR camera. Varied parameters were the jet Reynolds number in the range from 1,400 to 41,400, the normalized distance nozzle to sheet H/d from 1 to 10, and the normalized nozzle spacing S/d from 2 to 10. A geometrical arrangement of nine nozzle in-line arrays was tested. The results show that the multiple-jet system enhances the local and average heat transfer in comparison with that of a single nozzle. A maximum of the heat transfer was found for the normalized spacing S/d = 6.0. The normalized distance H/d has nearly no effect on the heat transfer in the range 2 ≤ H/d ≤ 4. The maximum average Nusselt number was correlated as a function of the jet Reynolds number      

Heat transfer from a flat surface to an inclined impinging jet

An experimental study was carried out to investigate the effect of the inclination jet on convection heat transfer to horizontal flat plate. Local heat transfer determined as a function is of three parameters including inclination angle of the air jet relative to the plate in range of 90° ≤ θ ≤ 45°, jet-to-plate spacing in range of 2 ≤ L/D ≤ 8 and Reynolds number in range of 1,500 ≤ Re ≤ 30,000. The results show that the maximum heat transfer point moves towards the uphill side of the plate and the maximum heat transfer decreases as the inclination angle decreases. The correlations were conducted to predict maximum and local Nusselt number as a function of Re, θ, L/D, and x/D for a specific three regions.     

Heat transfer from an obliquely impinging circular, air jet to a flat plate

A series of experiments was conducted for the measurement of local convective heat transfer coefficients for an obliquely impinging circular air jet to a flat plate. In the experiments, the oblique angles selected were 90°, 75°, 60° and 45°, with 90° being a vertical jet. Two different Reynolds numbers of 10,000 and 23,000 were considered for the purpose of comparison with previous data available in the literature. Another parameter varied in the measurements was the dimensionless jet-to-plate distance, L/D. Four values of L/D(2, 4, 7, and 10) were considered in the experiments. The experiments were conducted using the preheated wall transient liquid-crystal technique. Liquid-crystal color changes were recorded with a video system. Local convective heat transfer coefficients were obtained through the surface transient temperatures that were related to the recorded color information. Detailed local heat transfer coefficients were presented and discussed in relation to the asymmetric wall jet upon impingement of the jet flow. Results of experiments show that, for a given flow situation, the point of maximum heat transfer shifts away from the geometrical impingement point toward the compression side of the wall jet on the axis of symmetry. The shift is more pronounced with a smaller oblique angle (larger jet inclination) and a smaller jet-to-plate distance. Comparisons of experimental results with existing heat transfer data for both obliquely impinging jets and vertical impinging jets are made. The effect of oblique angles on heat transfer was assessed.     

Heat transfer augmentation between impinging circular air jet and flat plate using finned surfaces and vortex generators

An experimental investigation is performed to study the effect of the finned surfaces and surfaces with vortex generators on the local heat transfer coefficient between impinging circular air jet and flat plate. Reynolds number is varied between 7000 and 30,000 based on the nozzle exit condition and jet to plate spacing between 0.5 and 6 nozzle diameters. Thermal infrared imaging technique is used for the measurement of local temperature distribution on the flat plate. Fins used are in the form of cubes of 2 mm size spaced at a pitch of 5 mm on the target plate and hexagonal prism of side 2.04 mm and height of 2 mm spaced at a pitch of 7.5 mm. Vortex generators in the form of a equilateral triangle of side 4 mm are used. Effect of number of rows of vortex generators, radius of a row, number of vortex generators in a row and inclination angle (i.e., the angle between the plane of the target plate and the plane of the vortex generators) on Nusselt number is studied. It is observed that the heat transfer coefficient between the impinging jet and the target plate is sensitive to the shape of the fin. The increase in the heat transfer coefficient up to 77% depending on the shape of the fin, nozzle plate spacing and the Reynolds number is observed. The augmentation in the heat transfer for the surfaces vortex generators are higher than that of the finned surfaces. The heat transfer augmentation in case of vortex generator is as high as 110% for a single row of six vortex generators at a radius of 1 nozzle diameter as compared to the smooth surface at a given nozzle plate spacing of 1 nozzle diameter and a Reynolds number of 25,000 at extreme radial location.     

Heat transfer characteristics of premixed butane/air flame jet impinging on an inclined flat surface

 A series of experiments were carried out to determine the heat transfer characteristics of a round, premixed butane/air flame jet impinging upwards on an inclined flat plate, at different angles of incidence. The flame was fixed with an equivalence ratio of 1.0, a Reynolds number of 2500 and a plate-to-nozzle distance of 5d, while the inclination angles chosen for investigation were 57°, 67°, 80° and 90°. It was found that the location of the maximum heat flux point would be shifted away from the geometrical impingement point by reducing the angle of incidence. Decreasing the angle of incidence also enhanced the maximum local heat flux, while reduced the average heat transfer. The present study presented the effect of angle of incidence on the heat transfer characteristics of an impinging butane/air flame jet, which had been rarely reported in previous similar studies. Received on 11 October 2000 The authors wish to thank The Hong Kong Polytechnic University for the financial support of the present study.     

Optimization of an inclined elliptic impinging jet with cross flow for enhancing heat transfer

This work presents a parametric study and optimization of a single impinging jet with cross flow to enhance heat transfer with two design variables. The fluid flow and heat transfer have been analyzed using three-dimensional compressible Reynolds-averaged Navier–Stokes equations with a uniform heat flux condition being applied to the impingement plate. The aspect ratio of the elliptic jet hole and the angle of inclination of the jet nozzle are chosen as the two design variables, and the area-averaged Nusselt number on a limited target plate is set as the objective function. The effects of the design variables on the heat transfer performance have been evaluated, and the objective function has been found to be more sensitive to the angle of inclination of the jet nozzle than to the aspect ratio of the elliptic jet hole. The optimization has been performed by using the radial basis neural network model. Through the optimization, the area-averaged Nusselt number increased by 7.89% compared to that under the reference geometry.     

Heat transfer due to a round jet impinging normal to a circular cylinder

An experimental investigations of heat transfer for a stationary isothermal circular cylinder exposed normal to an impinging round air-jet has been reported. The circumferential heat transfer distributions as well as axial Nusselt number is measured. The measurements are taken as a function of the Reynolds number ranging from 3.8 × 10³ to 4 × 10⁴, the cylinder separation distance to the nozzle diameter (z/d) varying from 7 to 30, and the nozzle to cylinder diameter ratio (d/D) changing from 0.06 to 0.14. The output results indicated that the axial and radial distributions of the local heat transfer peaked at the impingement point. The heat transfer rate increases as the values of z decreases, for the same d and Re. The drop-off of the Nusselt number with increasing axial distance or radial angle from the impingement point was more pronounced for smaller z and d. The peripheral and surface average Nusselt numbers were determined by integration. The experimental data was used to produce correlations for both average and stagnation point heat transfer. Received on 4 January 1999     

Interaction of a circular turbulent jet with a flat target

Large eddy simulations are performed for an unsteady flow and heat transfer in the region of interaction of a circular turbulent jet with a normally positioned flat obstacle (target). Space-filtered Navier-Stokes equations are closed by the RNG model of eddy viscosity, which takes into account the curvature of streamlines in the region of flow turning. The computations are performed for different dimensionless distances between the nozzle exit and the target and for different Reynolds numbers. The dependence between the Nusselt number distribution over the target surface and the vortex structure of the jet is analyzed. The local and integral characteristics of the flow are compared with the data of a physical experiment. __________ Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 48, No. 1, pp. 55–67, January–February, 2007.     

Effect of external flow on the flow rate of a gas discharged through an orifice

The dependence of the flow coefficient of a gas jet ejected from an orifice/nozzle into a subsonic/transonic cross-flow on the flow and the jet Mach numbers, the off-design ratio, the nozzle inclination angle, β, and other determining parameters is considered. The physical nozzle flow pattern is constructed on the basis of experimental data obtained for 0.3< M_∞<1.75 and β=60°, 90°, and 120°. The results of measuring the pressure upstream and downstream of the orifice and on the windward and leeward orifice generators are presented. It is shown that the flow rate coefficient of a jet ejected into a cross-flow may exceed that of a similar jet outflowing into a flooded space. Moscow. Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No. 3, pp. 65–70, May–June, 1998.     

Heat and mass transfer study of impinging turbulent premixed flames

 Impinging jet combusting flows on granite plates are studied. A mathematical model for calculating heat release in turbulent impinging premixed flames is developed. The combustion including radiative heat transfer and local extinction effects, and flow characteristics are modeled using a finite volume computational approach. Two different eddy viscosity turbulence models, namely the standard k–ɛ and the RNG k–ɛ model with and without radiation (discrete transfer model) are assessed. The heat released predictions are compared with experimental data and the agreement is satisfactory only when both radiative heat transfer and local extinction modeling are taken into account. The results indicate that the main effect of radiation is the decrease of temperature values near the jet stagnation point and along the plate surface. Radiation increases temperature gradients and affects predicted turbulence levels independently of the closure model used. Also, the RNG k–ɛ predicts higher temperatures close the solid plate, with and without radiative heat transfer. Received on 13 November 2000 / Published online: 29 November 2001     

An experimental and numerical study into turbulent condensing steam jets in air

 Temperatures, velocities, and droplet sizes are measured in turbulent condensing steam jets produced by a facial sauna, for varying nozzle diameters and varying initial velocities (Re=3,600–9,200). The release of latent heat due to droplet condensation causes the temperature in the two-phase jet to be significantly higher than in a single-phase jet. At some distance from the nozzle, droplets reach a maximum size and start to evaporate again, which results in a change in sign of latent heat release. The distance of maximum size is determined from droplet size measurements. The experimental results are compared with semi-analytical expressions and with a fully coupled numerical model of the turbulent condensing steam jet. The increase in centreline temperature due to droplet condensation is successfully predicted. Received: 5 April 2000 / Accepted: 15 November 2000     

Numerical and experimental study of turbulent impinging twin-jet flow

The two dimensional impinging circular twin-jet flow with no-cross flow is studied numerically and experimentally. The theoretical predications are carried out through numerical procedure based on finite volume method to solve the governing mass, momentum, turbulent kinetic energy and turbulent kinetic energy dissipation rate. The parameters studied were jet Reynolds number (9.5 × 10⁴  Re  22.4 × 10⁴), nozzle to plate spacing (3  h/d  12), nozzle to nozzle centerline spacing (l/d = 3, 5 and 8) and jet angle (0°  θ  20°). It is concluded that the stagnation primary point moves away in the radial main flow direction by increasing the jet angle. This shift becomes stronger by increasing the nozzle to nozzle centerline spacing (l/d). A secondary stagnation point is set up between two jets. The value of pressure at this point decreases by decreasing Reynolds number and/or increasing the jet angle.

The sub atmospheric region occurs on the impingement plate. It increases strongly by increasing Reynolds number and decreases as the jet angle and/or a nozzle to plate spacing increases. The spreading of jet decreases by increasing nozzle to plate spacing. The intensity of re-circulation zone between two jets decreases by increasing of h/d and jet angle. The increase of turbulence kinetic energy occurs within high gradient velocity.     

Measurements of heat transfer coefficients between turbulent liquid jets and a radially finned heated disk placed at the bottom of an open vertical circular cavity

 Experiments have been performed to assess the impact of an extended surface on the heat transfer enhancement for axisymmetric, turbulent liquid jet impingement on a heated round disk. The disk, with an array of integral radial fins mounted on its surface, is placed at the bottom of an open vertical circular cavity. Hydrodynamic and heat transfer data were obtained for a dielectric fluorocarbon liquid FC-77. For a fixed circular heater of diameter D=22.23 mm, several geometric parameters were tested: the nozzle diameter (4.42≤d≤9.27 mm), the confining wall diameter of the vertical cavity (22.23≤D _c≤30.16 mm), and the nozzle-to-heater spacing (0.5≤S/d≤5.0). The FC-77 flow rates varied from =0.2 to 11.0 l/min producing Reynolds numbers in the wide interval 700≤Re _d ≤44,000. For d=4.42 mm, the heat transfer response to the separation distance S/d was small but increased gradually with increasing nozzle diameter up to d=9.27 mm. The thermal resistance R _th increased with the confining wall diameter D _c and also with the nozzle diameter d. A minimum value of the thermal resistance of R _th,min=0.4 cm² K/W was attained for a combination of d=4.42 mm, D _c=22.23 mm, S/d=1, and =7.5 l/min. Based on a simplified heat transfer model, reasonable agreement was obtained between measured values of the thermal resistance and the R _th-predictions. The total fin effectiveness ɛ_f was shown to increase with increasing nozzle diameter, but was invariant with the flow rate (or the jet exit velocity). More than a three-fold heat transfer enhancement was realized through the addition of the array of integral radial fins on the heated round disk. Received on 30 August 2000 / Published online: 29 November 2001     

Experimental investigation of mixed convection heat transfer in a horizontal and inclined rectangular channel

 Mixed convection heat transfer in rectangular channels has been investigated experimentally under various operating conditions. The lower surface of the channel is subjected to a uniform heat flux, sidewalls are insulated and adiabatic, and the upper surface is exposed to the surrounding fluid. Experiments were conducted for Pr=0.7, aspect ratios AR=5 and 10, inclination angles 0° ≤ θ ≤ 30°, Reynolds numbers 50 ≤ Re ≤ 1000, and modified Grashof numbers Gr*=7.0 × 10⁵ to 4.0 × 10⁷. From the parametric study, local Nusselt number distributions were obtained and effects of channel inclination, surface heat flux and Reynolds number on the onset of instability were investigated. Results related to the buoyancy affected secondary flow and the onset of instability have been discussed. Some of the results obtained from the experimental measurements are also compared with the literature, and a good agreement was observed. The onset of instability was found to move upstream for increasing Grashof number and increasing aspect ratio. On the other hand, onset of instability was delayed for increasing Reynolds number and increasing inclination angle. Received on 19 March 2001 / Published online: 29 November 2001     

Experimental and numerical investigations on slot air jet impingement cooling of a heated cylindrical concave surface

Experimental and numerical studies have been carried out for slot air jet impingement on a heated concave surface of a partially opened-top horizontal cylinder of length L = 20 cm. The slot jet is situated at the symmetry line of the partially opened-top cylinder along the gravity vector and impinges to the bottom of the cylinder which is designated as θ = 0°. The width of the opening at the top of the horizontal cylinder is W = 3 cm which corresponds to a circumferential angle Δθ = 50.8°. The experiments are performed by a Mach–Zehnder interferometer which enables to measure the local convection heat transfer coefficient. Also, a finite volume method based on the SIMPLE algorithm and non-orthogonal grid discretization scheme is used to solve the continuity, momentum, and energy equations. The Poisson equations are solved for (x, y) to find the grid points which are distributed in a non-uniform manner with higher concentration close to the solid regions. The effects of jet Reynolds number (Re _j) in the range from 190 to 1,600 and the ratio of spacing between nozzle and cylinder surface to the jet width from H = 1.5 to H = 10.7 on the local and average Nusselt numbers are examined. It is observed that maximum Nusselt number occurs at the stagnation point at (θ = 0°) and the local heat transfer coefficient decreases on the circumferential surface of the cylinder with increase of θ as a result of thermal boundary layer thickness growth. Also results show that the local and average heat transfer coefficients are raised by increasing the jet Reynolds number and by decreasing the nozzle-to-surface spacing.     

Mixed convection cooling of a heated circular cylinder by laminar upward-directed slot jet impingement

An experimental and numerical study has been carried out to investigate the heat transfer characteristics of a horizontal circular cylinder exposed to a slot jet impingement of air. A square-edged nozzle is mounted parallel with the cylinder axis and jet flow impinges on the bottom of the cylinder. The study is focused on low Reynolds numbers ranging from 120 to 1,210, Grashof numbers up to Gr = 10Re ² and slot-to-cylinder spacing from 2 to 8 of the slot width. The flow field is greatly influenced by the slot exit velocity and the buoyancy force due to density change. A Mach–Zehnder Interferometer is used for measurement of local Nusselt number around the cylinder at 10° interval. It is observed that the average Nusselt number decreases with increasing the jet spacing and increases with rising the Reynolds number. A finite volume method utilizing a curvilinear coordinate transformation is used for numerical modeling. The numerical results show good agreement with the experimental results. The flow and thermal field are seen to be stable and symmetric around the cylinder over the range of parameters studied.     

3D numerical simulation of compressible swirling flow induced by means of tangential inlets

The objective of the present work is to predict compressible swirl flow in the nozzle of air‐jet spinning using the realizable k–ε turbulence model and discuss the effect of the nozzle pressure. The periodic change of flow patterns can be observed. The recirculation zone near the wall of the injectors upstream increases in size and moves gradually upstream, whereas the vortex breakdown in the injector downstream shifts slowly towards the nozzle outlet during the whole period. A low axial velocity in the core region moves gradually away from the centerline, and the magnitude of the center reverse flow and the area occupied by it increase with axial distance due to the vortex breakdown. From the tangential velocity profile, there is a very small free‐vortex zone. With increasing nozzle pressure, the velocity increases and the location of vortex breakdown is moved slightly downward. However, the increase in the velocity tends to decline at nozzle pressure up to a high level. Copyright © 2008 John Wiley & Sons, Ltd.     

Computational flow and heat transfer of a row of circular jets impinging on a concave surface

A computational investigation is carried out to study the flow and heat transfer from a row of circular jets impinging on a concave surface. The computational domain simulates the impingement cooling zone of a gas turbine nozzle guide vane. The parameters, which are varied in the study include jet Reynolds number (Re _d = 5000–67800), inter-jet distance to jet diameter ratio (c/d = 3.33 and 4.67) and target plate distance to jet diameter ratio (H/d = 1, 3 and 4). The flow field, predicted with K-ω turbulence model and using Fluent 6.2.16, is characterized with the presence of a pair of counter rotating vortices, an upwash fountain flow and entrainment. The local pressure coefficient and Nusselt number variations along the concave plate are presented and these values are found to under predict the available experimental data by about 12%.     

Transient conjugate heat transfer from a hemispherical plate during free liquid jet impingement on the convex surface

This paper considers the analysis of transient heating of a hemispherical solid plate of finite thickness during impingement of a free liquid jet. A constant heat flux was imposed at the inner surface of the hemispherical plate at t = 0 and heat transfer was monitored for the entire duration of the transient until a steady state condition was reached. Calculations were done for Reynolds number (Re) ranging from 500 to 1,500 and dimensionless plate thicknesses to nozzle diameter ratio (b/d _n) from 0.083 to 1.5. Results are presented for local and average Nusselt number using water as the coolant and various solid materials such as silicon, constantan, and copper. It was detected that increasing the Reynolds number decreases the time for the plate to achieve the steady-state condition. Also, a higher Reynolds number increases the Nusselt number. Hemispherical plate materials with higher thermal conductivity maintain lower temperature non-uniformity at the solid–fluid interface. Increasing the plate thickness decreases the maximum temperature in the solid and increases the time to reach the steady-state condition.