Fabrication and electrochemical performance of nickel ferrite nanoparticles as anode material in lithium ion batteries

Nano-sized nickel ferrite (NiFe₂O₄) was prepared by hydrothermal method at low temperature. The crystalline phase, morphology and specific surface area (BET) of the resultant samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM) and nitrogen physical adsorption, respectively. The particle sizes of the resulting NiFe₂O₄ samples were in the range of 5–15 nm. The electrochemical performance of NiFe₂O₄ nanoparticles as the anodic material in lithium ion batteries was tested. It was found that the first discharge capacity of the anode made from NiFe₂O₄ nanoparticles could reach a very high value of 1314 mAh g⁻¹, while the discharge capacity decreased to 790.8 mAh g⁻¹ and 709.0 mAh g⁻¹ at a current density of 0.2 mA cm⁻² after 2 and 3 cycles, respectively. The BET surface area is up to 111.4 m² g⁻¹. The reaction mechanism between lithium and nickel ferrite was also discussed based on the results of cycle voltammetry (CV) experiments.     

Highly stable and selective Ru/NiFe_2O_4 catalysts for transfer hydrogenation of biomass-derived furfural to 2-methylfuran

Spinel ferrites NiFe_2O_4 supported Ru catalysts have been prepared via a simple sol–gel route and applied for converting biomass-derived furfural to 2-methylfuran. The as-prepared catalysts were characterized by thermogravimetric analysis(TG), N_2 adsorption–desorption, X-ray diffraction(XRD), scanning electronic microscopy(SEM), and X-ray photoelectron spectroscopy(XPS). Results showed that the catalysts had well-dispersed Ru active sites and large surface area for calcination temperature ranging from 300 to 500 ℃. The conversion of biomass-derived furfural into 2-methylfuran was conducted over Ru/NiFe_2O_4 through catalytic transfer hydrogenation in liquid-phase with 2-propanol as the hydrogen source. A significantly enhanced activity and increased 2-methylfuran yield have been achieved in this study. Under mild conditions(180 ℃ and 2.1 MPa N_2), the conversion of furfural exceeds 97% and 2-methylfuran yield was up to 83% over the catalyst containing 8 wt% Ru. After five repeated uses, the catalytic activity and the corresponding product yield remained almost unchanged. The excellent catalytic activity and recycling performance provide a broad prospects for various practical applications.     

Nickel ferrite/zinc oxide nanocomposite: Investigating the photocatalytic and antibacterial properties

A facile strategy was used for the synthesis of nickel ferrite/zinc oxide (NiFe₂O_4/ZnO) nanocomposite via an ultra-sonication method and observed its recyclability and photostability with enhanced visible light-driven photocatalytic performance. The photo degradation activities of as-synthesized photocatalysts were investigated using various dyes including methylene blue, crystal violet and methyl orange under solar light irradiation. Prepared material degrades 49.2% methyl orange, 44.4% methyl blue and 41.3% crystal violet in 40 min. Further, the synergistic effect of nickel ferrite and zinc oxide can reduce the probability of recombination of charge carrier and boost the charge separation which leads to remarkable photocatalytic performance. Magnetic properties of nickel ferrite reduces the agglomeration of material and increases the recyclability. The NiFe₂O_4/ZnO nanocomposites also exhibited better antibacterial activity for Pseudomonas aeruginosa and Staphylococcus aureus, which shows that they can be used for both environmental and biological applications.     

Core shell‐structured NiFe2O4@TiO2 nanoparticle‐anchored reduced graphene oxide for rapid degradation of rhodamine B

In this work, the NiFe₂O₄@TiO₂/reduced graphene oxide (RGO) ternary nanocomposites with high saturation magnetization and catalytic efficiency have been synthesized through the following steps. First, graphene oxide was prepared using the modified Hummer's method. Second, the NiFe₂O₄ nanoparticles were successfully prepared using the hydrothermal method. Third, the core shell‐structured NiFe₂O₄@TiO₂/RGO nanocomposite precursors were easily obtained through hydrolysis reaction. The morphology of NiFe₂O₄@TiO₂/RGO nanocomposites was characterized from scanning electron microscope (SEM) and transmission electron microscope (TEM) images. Moreover, the results of X‐ray diffraction (XRD) patterns proved that the TiO₂ coating shell consisted of anatase. The vibrating sample magnetometer (VSM) measurements showed that the saturation magnetization value of NiFe₂O₄@TiO₂/RGO ternary nanocomposites was 25 emu/g. The X‐ray photoelectron spectroscopy (XPS) analysis confirmed that only part of the graphite oxide (GO) was reduced to RGO in the ternary nanocomposite. The degradation experiments proved that NiFe₂O₄@TiO₂/RGO nanocomposite exhibited the high catalytic efficiency and outstanding recyclable performance for rhodamine B (RhB).     

Lime peel extract induced NiFe2O4 NPs: Synthesis to applications and oxidative stress mechanism for anticancer,antibiotic activity

Nanobiotechnology, joined with green science, has incredible potential for the advancement of novel and important products that benefit human health, climate, and industries. Green chemistry of materials from synthesis to diverse biomedical applications is a talk of town in today’s sustainable ideal world. Green synthesized nickel ferrites nanoparticles via biogenic lime peel extract (LPE) are investigated with precision and complete trail has been reported as multiple efficacies. The fcc crystal structure with the crystallite size (31 nm) were accessed by the XRD, magnetic properties using VSM, and FTIR for the functional group analysis of NiFe₂O₄ nanoparticles mediated by Lime peel extract (NiFe₂O₄@LPE NPs). From TEM and SEM analysis the average diameter of the NPs was observed in the range of 31–35 nm. In 3D view, the surface morphology was analyzed by the AFM. NiFe₂O₄@LPE NPs were used to assess cytotoxicity and cellular morphological alterations in In Vitro cervical cancerous cells (HeLa). Nanosized NiFe₂O₄@LPE accompanied the considerable NPs topology induced dose dependent MMP in HeLa cells unlike the previous interpretation of controlled metabolism anticancer activity for HeLa cancerous cells. Therefore, it is referred by oxidative stress and reduction phenomena for anticancer effects and inactivation of carcinogen. Moreover, Antioxidant DPPH radical scavenging method and antibacterial Bacillus subtilis, Escherichia coli, Pseudomonas aeruginosa, and Staphylococcus aureus activity were observed in the synthesized nickel ferrites NPs.     

Ni ion-containing immobilized ionic liquid on magnetic Fe3O4 nanoparticles: An effective catalyst for the Heck reaction

In this work, we synthesized Ni²⁺-containing 1-methyl-3-(3-trimethoxysilylpropyl) imidazolium chloride ionic liquid on magnetic Fe₃O₄ nanoparticles. The catalytic activity of these novel nanocomposites was finally evaluated for the Heck reaction at 100 °C, and can be reused after washing without loss in activity. The immobilized ionic liquid catalysts proved to be effective and easily separated from the reaction media by applying an external magnetic field. This procedure has many obvious advantages compared to those reported in the previous literature, including avoidance of the use of the expensive Pd catalysts, mild reaction conditions, high yields, and simplicity of the methodology.     

A WO3 nanorod-Cr2O3 nanoparticle composite for selective gas sensing of 2-butanone

The sensor based on WO₃-Cr₂O₃ nanocomposites show good selectivity to 2-butanone.     

NiFe2O4/g-C3N4 heterojunction composite with enhanced visible-light photocatalytic activity

Spinel structure nickel ferrite (NiFe₂O₄) doped graphitic carbon nitride (g-C₃N₄) photocatalyst NiFe₂O₄/g-C₃N₄ was synthesized by the coprecipitation route to enhance the photocatalytic activity for the visible-light driven degradation of methyl orange. The NiFe₂O₄ doping content is responsible for the microstructure and photocatalytic activity of NiFe₂O₄/g-C₃N₄ samples. Compared with pure NiFe₂O₄ and g-C₃N₄, the 2-NiFe₂O₄/g-C₃N₄ composite with NiFe₂O₄ doping of 2.0 wt% exhibited excellent photocatalytic activity and superior stability after five runs for degrading methyl orange under visible light irradiation. The catalytic activity of 2-NiFe₂O₄/g-C₃N₄ sample produced using the coprecipitation route was higher than those of conventional 2-NiFe₂O₄/g-C₃N₄ bulks prepared by the impregnation approach. The prepared samples for the photocatalytic degradation of methyl orange followed pseudo-first-order reaction kinetics. It’s ascribed to the synergistic effect between NiFe₂O₄ and g-C₃N₄, which can inhibit the recombination of photoexcited electron-hole pairs, accelerate photoproduced charges separation, and enhance the visible light absorption.     

Recyclable Fenton-like catalyst based on zeolite Y supported ultrafine,highly-dispersed Fe2O3 nanoparticles for removal of organics under mild conditions

The active Fenton-like catalyst, obtained by highly dispersed Fe₂O₃ nanoparticles in size of 5 nm on the surface of zeolite Y, shows the excellent degradation efficiency to phenol higher than 90% under the mild conditions of room temperature and neutral solution, and the catalyst can be easily recovered with stable catalytic activity for 8 cycles.     

Facile synthesis and properties of ZnFe2O4 and ZnFe2O4/polypyrrole core-shell nanoparticles

We demonstrated that ZnFe₂O₄/polypyrrole core-shell nanoparticles could be facilely synthesized via in situ chemical oxidative polymerization of pyrrole monomers on the surface of ZnFe₂O₄ nanoparticles. The shell thickness of core-shell nanoparticles could be easily controlled by adjusting the amount of pyrrole monomers. The phase structures, morphologies and properties of the as-prepared products were investigated by XRD, TEM, SEM, VSM, and FTIR spectra. Magnetic studies revealed that the saturation magnetization (M_s) and coercivity (H_c) of ZnFe₂O₄/PPy core-shell nanoparticles is 17.8 emu/g and 130 Oe, respectively. The electromagnetic characteristics of products showed that ZnFe₂O₄/PPy core-shell nanoparticles exhibit excellent microwave absorption performance than ZnFe₂O₄ nanoparticles, such as more powerful absorbing property and wider electromagnetic wave absorbing frequency band due to the proper matching of the permittivity and the permeability of ZnFe₂O₄/PPy core-shell nanoparticles.     

Removal of sulfur from commercial kerosene using nanocrystalline NiFe2O4 based sorbents

This paper deals with the simultaneous removal of sulfur from commercial kerosene at room temperature using sorbents containing NiFe₂O₄ nanoparticles. The nanocrystalline NiFe₂O₄ based sorbents were prepared using the combustion route. The effect of fuel content on the surface properties and desulferization activity of Ni/Fe mixed oxide sorbents has been studied.It was observed that incorporation of metal cations (Ni²⁺) into the hematite (α-Fe₂O₃) crystal structure alters the surface properties and desulferization activity of the investigated oxides, which in turn depends on the nature and concentration of the incorporated metal cation and the released heat during the combustion process. The effect of fuel content in modifying the resultant surface area could be directly related to the variations in the rate of crystal growth of the solids studied depending upon preparation temperature. Interestingly, all the prepared ferrites exhibit a narrow pore size distribution in the range of 0.9–2 nm. The capacity of NiFe₂O₄ to adsorb sulfur from commercial kerosene was evaluated in terms of their textural and chemical characteristics.     

Removal of arsenic from aqueous solution: A study of the effects of pH and interfering ions using iron oxide nanomaterials

Nanophase Fe₃O₄ and Fe₂O₃ were synthesized through a precipitation method and were utilized for the removal of either arsenic (III) or (V) from aqueous solution as a possible method for drinking water treatment. The synthesized nanoparticles were characterized using X-ray diffraction, which showed that the Fe₃O₄ and the Fe₂O₃ nanoparticles had crystal structures of magnetite and hematite, respectively. In addition, Secherrer's equation was used to determine that the grain size nanoparticles were 12 ± 1.0 nm and 17 ± 0.5 nm for the Fe₂O₃ and Fe₃O₄, respectively. Under a 1 h contact time, batch pH experiments were performed to determine the optimum pH for binding using 300 ppb of either As(III) or (V) and 10 mg of either Fe₃O₄ or Fe₂O₃. The binding was observed to be pH independent from pH 6 through pH 9 and a significant drop in the binding was observed at pH 10. Furthermore, batch isotherm studies were performed using the Fe₂O₃ and Fe₃O₄ to determine the binding capacity of As(III) and As(V) to the iron oxide nanomaterials. The binding was found to follow the Langmuir isotherm and the capacities (mg/kg) of 1250 (Fe₂O₃) and 8196 (Fe₃O₄) for As(III) as well as 20,000 (Fe₂O₃) and 5680 (Fe₃O₄) for As(III), at 1 and 24 h of contact time, respectively. The As(V) capacities were determined to be 4600 (Fe₂O₃), 6711(Fe₃O₄), 4904 (Fe₂O₃), and 4780 (Fe₃O₄) mg/kg for nanomaterials at contact times of 1 and 24 h respectively.     

A quantitative colorimetric assay of H2O2 and glucose using silver nanoparticles induced by H2O2 and UV

A simple spectrophotometric assay of H2O2 and glucose using Ag nanoparticles has been carried out. Relying on the synergistic effect of H2O2 reduction and ultraviolet （UV） irradiation, Ag nanoparticles with enhanced absorption signals were synthesized. H2O2 served as a reducing agent in the Ag nanoparticles formation in which Ag＋ was reduced to Ago by O2- generated via the decomposition of H2O2 in alkaline media. On the other hand, photoreduction of Ag＋ to Ago under UV irradiations also contributed to the nanoparticles formation. The synthesized nanoparticles were characterized by TEM, XPS, and XRD. The proposed method could determine H2O2 with concentrations ranging from 5.0× 10^-7 to 6.0× 10^-5 tool/ L The detection limit was estimated to be 2.0 × 10^-7 mol/L. Since the conversion of glucose to gluconic acid catalyzed by glucose oxidase was companied with the formation of H2O2, the sensing protocol has been successfully utilized for the determination of glucose in human blood samples. The results were in good agreement with those determined by a local hospital. This colorimetric sensor thus holds great promises in clinical applications.     

Controlled synthesis of MnSn(OH)6/graphene nanocomposites and their electrochemical properties as capacitive materials

We report the synthesis of novel MnSn(OH)₆/graphene nanocomposites produced by a co-precipitation method and their potential application for electrochemical energy storage. The hydroxide decorated graphene nanocomposites display better performance over pure MnSn(OH)₆ nanoparticles because the graphene sheets act as conductive bridges improving the ionic and electronic transport. The crystallinity of MnSn(OH)₆ nanoparticles deposited on the surface of graphene sheets also impacts the capacitive properties as electrodes. The maximum capacitance of 31.2 F/g (59.4 F/g based on the mass of MnSn(OH)₆ nanoparticles) was achieved for the sample with a low degree of crystallinity. No significant degradation of capacitance occurred after 500 cycles at a current density of 1.5 A/g in 1 M Na₂SO₄ aqueous solution, indicating an excellent electrochemical stability. The results serve as an example demonstrating the potential of integrating highly conductive graphene networks into binary metal hydroxide in improving the performance of active electrode materials for electrochemical energy storage applications.     

Catalytic oxidation of cyclohexane with hydrogen peroxide and a tetracopper(II) complex in an ionic liquid

The catalytic peroxidative oxidation (with H₂O₂) of cyclohexane in an ionic liquid (IL) using the tetracopper(II) complex [(CuL)₂(μ₄-O,O′,O′′,O′′′-CDC)]₂·2H₂O [HL = 2-(2-pyridylmethyleneamino)benzenesulfonic acid, CDC = cyclohexane-1,4-dicarboxylate] as a catalyst is reported. Significant improvements on the catalytic performance, in terms of product yield (up to 36%), TON (up to 529), reaction time, selectivity towards cyclohexanone and easy recycling (negligible loss in activity after three consecutive runs), are observed using 1-butyl-3-methylimidazolium hexafluorophosphate as the chosen IL instead of a molecular organic solvent including the commonly used acetonitrile. The catalytic behaviors in the IL and in different molecular solvents are discussed.     

Low charge overpotentials and extended full cycling capability in lithium-oxygen batteries by controlling the nature of discharge products

Hollow NiCo₂O₄ microspheres with a highly hierarchical porous structure were synthesized and conducted as catalysts for lithium-oxygen batteries. The influence of NiCo₂O₄ on the discharge products was investigated. The NiCo₂O₄ showed the capability to promote the formation of lithium deficient Li_2 − xO₂ and exerted a significant influence on the electrochemical performance of lithium-oxygen batteries with a low charge overpotential and extended full cycling over 50 cycles.     

Macroporous Co3O4 platelets with excellent rate capability as anodes for lithium ion batteries

This paper reports the microwave-assisted synthesis of Co₃O₄ nanomaterials with different morphologies including nanoparticles, rod-like nanoclusters and macroporous platelets. The new macroporous platelet-like Co₃O₄ morphology was found to be the best suitable for reversible lithium storage properties. It displayed superior cycling performances than nanoparticles and rod-like nanoclusters. More interestingly, excellent high rate capabilities (811 mAh g^?1 at 1780 mA g^?1 and 746 mAh g^?1 at 4450 mA g^?1) were observed for macroporous Co₃O₄ platelet. The good electrochemical performance could be attributed to the unique macroporous platelet structure of Co₃O₄ materials.     

One-step synthesis of poly(thionine)-Au nano-network and nanowires and its application for non-enzyme biosensing of hydrogen peroxide

We describe the preparation of novel poly(thionine)-Au materials, where the poly(thionine)-Au nano-network and nanowires have been synthesized in aqueous solution via the polymerization of thionine using HAuCl₄ as the oxidant in a single reaction setup. The synthesis process does not require templates, nor does it require large amounts of organic solvents or electrochemical methods. The morphology of the nanocomposites can be controlled by varying the thionine/HAuCl₄ ratio. The resulting poly(thionine)-Au network was used to fabricate a novel non-enzyme hydrogen peroxide (H₂O₂) biosensor. In pH 7.0 phosphate buffer, almost interference-free determination of H₂O₂ was realized at − 0.1 V versus Ag/AgCl with a linear of 1 × 10^− 4 to 5 × 10^− 2 M, a correlation coefficient of 0.998 and a response time of < 2 s. The developed biosensor showed a detection limit of 0.2 μM (S/N = 3) with very good stability, reproducibility and high selectivity.     

A strategy for scalable synthesis of Li4Ti5O12/reduced graphene oxide toward high rate lithium-ion batteries

Li₄Ti₅O₁₂/reduced graphene oxide (RGO) composites were prepared via a simple strategy. The as-prepared composites present Li₄Ti₅O₁₂ nanoparticles uniformly immobilized on the RGO sheets. The Li₄Ti₅O₁₂/RGO composites possess excellent electrochemical properties with good cycle stability and high specific capacities of 154 mAh g^− 1 (at 10C) and 149 mAh g^− 1 (at 20C), much higher than the results found in other literatures. The superior electrochemical performance of the Li₄Ti₅O₁₂/RGO composites is attributed to its unique hybrid structure of conductive graphene network with the uniformly dispersed Li₄Ti₅O₁₂ nanoparticles.     

A novel hydrogen peroxide sensor based on Ag nanoparticles electrodeposited on DNA-networks modified glassy carbon electrode

A novel strategy to fabricate hydrogen peroxide (H₂O₂) sensor was developed by electrodepositing Ag nanoparticles (NPs) on a glassy carbon electrode modified with three-dimensional DNA networks. The result of electrochemical experiments showed that such constructed sensor had a favorable catalytic ability to reduction of H₂O₂. The well catalytic activity of the sensor was ascribed to the DNA networks that facilitated the formation and homogenous distribution of small Ag NPs. The resulted sensor achieved 95% of the steady-state current within 2 s and had a 1.7 μM detection limit of H₂O₂.