SiO2和Al2O3负载的Ni基催化剂在甲烷干重整中的催化性能差异

CH₄与CO₂干重整反应对于环境保护和天然气资源的合理利用具有重要意义。SiO₂和Al₂O₃是适用于甲烷干重整反应的两种典型的催化剂载体。为了阐明这两种载体对催化剂性能的影响,本研究采用等体积浸渍法制备了Ni/Al₂O₃和Ni/SiO₂催化剂,并利用BET、TEM、H₂-TPR、XRD、TG和Raman等技术对还原和反应后的催化剂进行了表征。结果表明,由于载体的性质不同,Ni基催化剂在甲烷干重整中的催化性能也不同。Ni/SiO₂催化剂的初始活性较高,但由于其金属-载体相互作用较弱,催化稳定性较差,在800℃下反应15h其催化活性急剧下降;较弱的金属-载体相互作用使得Ni/SiO₂催化剂上的Ni颗粒较大,有利于积炭前驱物种的生成,导致催化剂快速失活。而对于Ni/Al₂O₃催化剂,金属-载体相互作用较强,Ni颗粒较小,但由于Ni与Al₂O₃生成了NiAl_xO_y物种,有效活性位减少,其催化活性相对较低,但催化稳定性较好,干重整反应进行50h其活性保持稳定;Ni与Al₂O₃之间较强的相互作用有利于形成小且稳定的Ni粒子,能减少积炭,因而具有优异的催化稳定性。     

不同载体Ni基负载型催化剂对甲烷部分氧化制合成气催化行为研究

采用浸渍法制备了单一载体(Al₂O₃、ZrO₂、CeO₂)和ZrO₂、CeO₂改性的Al₂O₃复合载体的Ni催化剂,考察了在甲烷部分氧化制备合成气反应中的催化性能。通过N₂-物理吸附、H₂程序升温还原、X射线衍射、NH₃程序升温脱附和程序升温氧化等技术对催化剂进行了表征。结果表明,在单一载体催化剂中,Ni/Al₂O₃具有较大的比表面积,其初始反应活性较高,但该催化剂表面易形成大量的积炭而快速失活。Ni/ZrO₂和Ni/CeO₂催化剂比表面积较小,活性金属Ni在其表面分散性差,催化剂具有较低的CH₄转化率。而CeO₂和ZrO₂改性的Al₂O₃复合载体催化剂,具有较大的比表面积,反应活性明显高于单一载体催化剂。CeO₂-Al₂O₃复合载体催化剂具有最高的反应活性和较好的反应稳定性。同时表明,含CeO₂催化剂反应后表面积炭较少,CeO₂的储放氧功能增强了催化剂对O₂的活化,提高催化剂活性的同时,可以抑制积炭的生成。     

Carbon Dioxide Reforming of Methane over Ni Catalysts Supported on Al2O3 Modified with La2O3, MgO, and CaO

The preparation of synthesis gas from carbon dioxide reforming of methane (CDR) has attracted increasing attention. The present review mainly focuses on CDR to produce synthesis gas over Ni/MO_x/Al₂O₃ (X = La, Mg, Ca) catalysts. From the examination of various supported nickel catalysts, the promotional effects of La₂O₃, MgO, and CaO have been found. The addition of promoters to Al₂O₃-supported nickel catalysts enhances the catalytic activity as well as stability. The catalytic performance is strongly dependent on the loading amount of promoters. For example, the highest CH₄ and CO₂ conversion were obtained when the ratios of metal M to Al were in the range of 0.04–0.06. In the case of Ni/La₂O₃/Al₂O₃ catalyst, the highest CH₄ conversion (96%) and CO₂ conversion (97%) was achieved with the catalyst (La/Al = 0.05 (atom/atom)). For Ni/CaO/Al₂O₃ catalyst, the catalyst with Ca/Al = 0.04 (atom/atom) exhibited the highest CH₄ conversion (91%) and CO₂ conversion (92%) among the catalysts with various CaO content. Also, Ni/MgO/Al₂O₃ catalyst with Mg/Al = 0.06 (atom/atom) showed the highest CH₄ conversion (89%) and CO₂ conversion (90%) among the catalysts with various Mg/Al ratios. Thus it is most likely that the optimal ratios of M to Al for the highest activities of the catalysts are related to the highly dispersed metal species. In addition, the improved catalytic performance of Al₂O₃-supported nickel catalysts promoted with metal oxides is due to the strong interaction between Ni and metal oxide, the stabilization of metal oxide on Al₂O₃ and the basic property of metal oxide to prevent carbon formation.     

合成方法对Rh/CeO2-ZrO2-La2O3催化剂的结构、表面性能及DeNOx活性的影响

用沉积沉淀法合成两种不同系列的CeO2-ZrO2-La2O3混合氧化物(ZrO2和La2O3沉积CeO2粒子(标记为A-x)以及CeO2和La2O3沉积ZrO2粒子(标记为B-x)),并用作Rh催化剂的载体。XRD、拉曼、TPR、XPS和O2脉冲等表征结果显示出不同的沉积顺序将导致不同的结构和氧化还原性能,且B-x具有更高的氧迁移性、储氧能力和表面Ce浓度。当其负载Rh后,Rh/B-x催化剂具有更高的NO和CO转化率及N2选择性,且Ce的最佳含量为50at%。这可能归因于Rh负载于富铈表面形成更多有利于NO分解的表面Ce3+活性位。     

Effect of Ni loadings on the activity and coke formation of MgO-modified Ni/Al2O3 nanocatalyst in dry reforming of methane

MgO-modified Ni/Al₂O₃ catalysts with different Ni loadings were prepared and employed in dry reforming of methane (DRM). The effect of Ni loadings on the activity and coke formation of Ni/MgO-Al₂O₃ catalysts were investigated. The synthesized catalysts were characterized by XRD, N₂ adsorption-desorption, SEM, TPO and TPR techniques. The obtained results showed that increasing nickel loading decreased the BET surface area and increased the catalytic activity and amount of deposited carbon. In addition, the effect of gas hourly space velocity (GHSV) and feed ratio were studied.     

Influence of support on resistance to carbon-deposition of catalyst for CH4, CO2 with O2 to synthesis gas

In the reaction of catalytic oxidation of CH₄, CO₂ with O₂ to synthesis gas, carbon-deposition is an important factor for deactivation. By adding different oxides to Ni/Al₂O₃ catalyst, its resistance to carbon-deposition was improved. The experimental results indicate that the order of resistance to carbon-deposition is as follows: Ni/CaO-Al₂O₃>Ni/MgO-Al₂O₃>Ni/ TiO₂-Al₂O₃ > Ni/CeO₂-Al₂O₃>Ni/La₂O₃-Al₂O₃>Ni/Y₂O₃-Al₂O₃>Ni/Fe₂O₃-Al₂O₃>Ni/Al₂O₃. The catalysts were characterized by CO₂-TPD, O₂-TPD and XPS methods. Here the relation between the order of resistance to carbon-deposition and performance of catalyst is discussed.     

Catalytic methanol decomposition to carbon monoxide and hydrogen over Pd/CeO2-ZrO2-La2O3 with different Ce/Zr molar ratios

The catalytic behaviors of Pd (1.4 wt%) catalysts supported on CeO₂-ZrO₂-La₂O₃ mixed oxides with different Ce/Zr molar ratios were investigated for methanol decomposition. Nitrogen adsorption-desorption (BET), X-ray photoelectron spectroscopy (XPS), H₂ temperature-programmed reduction (H₂-TPR), X-ray diffraction (XRD) and Pd dispersion analysis were used for their characterization. Pd/Ce_0.76Zr_0.18 La_0.06O_1.97 catalyst showed the highest BET surface area, best Pd dispersion capability and strongest metal-support interaction. Moreover, XPS showed that there was lattice defect oxygen or mobile oxygen. According to the result of O 1s measurements the lattice defect oxygen or mobile oxygen helped to maintain Pd in a partly oxidized state and increased the activity for methanol decomposition. The Pd/Ce_0.76Zr_0.18La_0.06O_1.97 catalyst exhibited the best activity. A 100% conversion of methanol was achieved at around 260 °C, which was about 20-40 °C lower than other catalysts     

Catalytic Combustion of Methane over CeO2-MOx (M=La, Ca) Solid Solution Promoted Pd/γ-Al2O3 Catalysts

Solid solution CeO₂-MO_x (M=La³⁺, Ca²⁺) promoted Pd/γ-Al₂O₃ catalysts were prepared by a deposition-precipitation method. The structural properties were investigated by X-ray diffraction, X-ray photoelectron spectroscopy, and Raman spectroscopy. The results showed that Mⁿ⁺ ions incorporated into CeO₂ lattice and solid solutions formed in Pd/γ-Al₂O₃-CeO₂-MO_x catalysts. The formation of solid solution was confirmed by the change in lattice parameters of CeO₂ and the shift of 2θ angles as compared with pure CeO₂. A strain formed in the O²⁻ sub-lattice of CeO₂ was revealed by Raman analyses, which decreased the intensity of the Raman-active band at around 463 cm⁻¹ owing to the F_2g symmetric stretching of Ce−O bond. The appearance of a new band at 615 cm⁻¹ (in the case of Pd/γ-Al₂O₃-CeO₂-CaO) and a shoulder at 320 cm⁻¹ (in the case of Pd/γ-Al₂O₃-CeO₂-La₂O₃) was also confirmed. Ionic Pd^δ+ species were formed in the catalysts, which exhibited higher binding energies (0.5−0.6 eV higher for Pd 3d_5/2) than that of normal PdO. The catalysts showed high activity and stability for low temperature methane combustion. 10% and 100% conversions of methane could be obtained at temperatures of 254 and 340 °C, respectively, over Pd/γ-Al₂O₃-CeO₂-La₂O₃ catalyst under an hourly space velocity of 50000 h⁻¹.     

Autothermal Reforming of Methane over Ni Catalysts Supported on CuO-ZrO2-CeO2-Al2O3

Ni catalysts supported on various mixed oxides of Al2O3 with rare earth oxide and transitional metal oxides were synthesized. The studies focused on the measurement of the autothermal reforming of methane to hydrogen over Ni catalysts supported on the mixed oxide ZrxCe30-xAl70Oδ (x=5, 10, 15). The catalytic performance of Ni/Zr10Ce20Al70Oδ was better than that of other catalysts. XRD results showed that the addition of Zr to Ni/Ce30Al70Oδ prevented the formation of NiAl2O4 and facilitated the dispersion of NiO. Effects of CuO addition to Zr10Ce20Al70Oδ were also investigated. The activity of Ni catalyst supported on CuO-ZrO2-CeO2-Al2O3 was somewhat affected and the Ni/Cu5Zr10Ce20Al65Oδ showed the best catalytic performance with the highest CH4 conversion, yield of H2, selectivity for H2 and H2/CO production ratio in operation temperatures ranging from 650 to 750℃.     

Design of coke-free methane dry reforming catalysts by molecular tuning of nitrogen-rich combustion precursors

The valorization of methane and carbon dioxide is a promising solution for mitigating global warming. The dry reforming of methane (DRM) is capable of concomitant conversion of these greenhouse gases into starting materials for production of synthetic fuels, promoting a carbon neutral avenue for fuel production. The development of efficient, stable, and economic catalysts presents a challenge owing to the comparatively rapid deactivation of DRM catalysts under reaction conditions. Here, Ni/La₂O₃ DRM catalysts are prepared by combustion synthesis of Ni and La complexes of nitrogen-rich precursors. We expound the relationship between structures of the combustion precursors, the thermochemistry of their combustion, the structures of the resultant Ni/La₂O₃ catalysts, and their performance under DRM conditions. We show that the best catalyst is derived from energetic precursor which has the sharpest exotherm and rapidly releases the largest amounts of nitrogen gas. These properties give rise to the crystallization of the Ni/La₂O₃ catalyst with high Ni dispersion and strong metal-support interactions. This work can act as starting point to expand the link between the chemistry of combustion precursors and the resulting catalyst properties, eventually realizing the rational design of high-performance catalysts prepared by combustion synthesis through tailoring the chemistry and structure of the nitrogen-rich precursors.     

负载Ni催化剂用于乙二醇蒸汽重整制氢催化性能研究

采用等体积浸渍法和共沉淀法制备了Ni催化剂,在固定床反应器上考察了Ni负载量、焙烧温度、反应温度等因素对乙二醇低温重整制氢反应活性和选择性的影响。应用X射线衍射、氮物理吸附、H₂程序升温还原等技术对负载型Ni催化剂进行了表征。结果表明,共沉淀法制备的Ni/CeO₂催化剂具有较小的NiO颗粒与CeO₂载体颗粒粒径,催化活性较高。添加少量氧化钴到Ni/CeO₂催化剂中可使H₂收率达72.6%,EG转化率达93.1%。在CeO₂中添加Al₂O₃能提高负载Ni催化剂的活性,乙二醇转化率达94.0%,H₂收率达67.0%;但添加SiO₂则使其活性明显变差。     

Effect of promoters on the catalytic performance of Ni/Al2O3 catalyst for partial oxidation of methane to syngas

The effect of promoters such as Ce, La and Ca on catalytic performance of Ni catalyst was measured in a continuous fixed bed reactor. The effect of promoters on Ni/a-Al₂O₃ catalyst is more significant than on Ni/g-Al₂O₃ catalyst. Ce was proved to be the best promoter among the three promoters tested and the optimum loading of Ce was 1%. The catalyst was characterized by TG, XPS, TPR and XRD techniques. TPR results showed that Ce can improve the reducibility of the Ni/Al₂O₃ catalyst. XRD results indicated that Ce was highly dispersed when its loading was low, but at higher loading it was crystallized into bulk CeO₂, thus, decreased the catalytic activity. This revised version was published online in June 2006 with corrections to the Cover Date.     

Ni基催化剂催化燃油重整耦合选择性催化还原NOx反应

分别以La₂O₂CO₃, CeO₂, ZrO₂和Al₂O₃为载体, 采用浸渍法制备了Ni基重整催化剂, 并以正十二烷模拟车载燃油进行催化重整反应以同时制备小分子碳氢化合物(HCs)和H₂, 考察了其在4wt%Ag/Al₂O₃上选择性催化还原(HC-SCR)氮氧化物(NO_x)的性能. 采用N₂吸附-脱附、X射线粉末衍射、H₂程序升温还原和热重等手段对Ni基催化剂进行了表征. 结果表明, 随着重整催化剂氧化还原性能增强, 产物中H₂浓度增加, 可参与SCR反应的HCs含量减少, 从而导致重整-SCR耦合体系上NO_x净化活性温度窗口向低温移动, NO_x最高转化率降低. Ni/ZrO₂+Ag/Al₂O₃耦合体系中H₂/HCs符合SCR反应所需的最优比例, 在柴油车典型排气温度范围内表现出良好的NO_x净化能力. 同时, 在Ni/ZrO₂+Ag/Al₂O₃耦合体系上考察了其燃油重整-SCR的活性稳定性. 结果显示, 重整催化剂的耐久性有待进一步提高.     

M/Al2O3-CeO2（M=Pt-Ru，Ru，Pt）催化剂在甲胺催化湿式氧化中的活性与选择性

采用浸渍法制备了M/Al₂O₃-CeO₂（M=Pt-Ru,Ru,Pt）催化剂,并将其用于甲胺的催化湿式氧化反应（CWAO）.结果表明,Pt-Ru/Al₂O₃-CeO₂具有最佳活性和选择性.运用程序升温还原、X射线光电子能谱、X射线衍射、透射电子显微镜、N₂吸附和CO化学吸附等技术对催化剂的物化性质进行了表征.Pt组分的引入可有效提高双金属催化剂活性组分的分散度,从而明显提高了其催化性能.升降温过程中总有机碳（TOC）转化率与N₂选择性迟滞效应表明,甲胺CWAO遵循化学吸附-脱附机理.     

Preparation of apatite-type-silicate-supported precious metal catalysts for selective catalytic reduction of NOx

Apatite-type silicate supported precious metal catalysts were prepared and investigated for their catalytic activity in selective catalytic NO reduction. Single-phase La_9.33Si₆O₂₆ and La_8.33ASi₆O_25.5 (A=Ca, Sr, Ba) were obtained by a sol-gel method. Pd/La_9.33Si₆O₂₆ catalyst exhibited high activity for oxidation of C₃H₆, comparable to Pd/Al₂O₃ catalyst, although the specific surface area of La_9.33Si₆O₂₆ was lower than that of Al₂O₃. In addition, Pt/La_9.33Si₆O₂₆ catalyst exhibited higher activity for selective catalytic reduction of NO than Pt/Al₂O₃ catalyst. Substitution of Ba²⁺ for La³⁺ of La_9.33Si₆O₂₆ led to increased catalytic activity at low temperature.     

Effect of Steam in CO2 Reforming of CH4over a Ni/CeO2–ZrO2–Al2O3 Catalyst

CO₂ reforming of CH₄ was carried out with and without steam over a Ni/CeO₂–ZrO₂–Al₂O₃ catalyst. The catalytic performance, amount of carbon deposit and the EXAFS of the Ni K-edge of samples were measured. The results show that when the catalyst is used for CO₂ reforming of CH₄ without the addition of steam, the catalyst gradually deactivates, however, addition of a small amount of steam to the feed gas can significantly inhibits the deactivation, which is due to the great suppression of coke formation on the catalyst during the reaction. The EXAFS result shows that, maybe due to the penetration of more carbon atoms into the Ni lattice, the coordination number of the nearest Ni–Ni of the sample after the reaction without steam reduces more than that of samples after the reaction with a small amount of steam in the feed gas.     

Perovskites as Precursors for Ni/La2O3 Catalysts in the Dry Reforming of Methane: Synthesis by Constant pH Co‐Precipitation,Reduction Mechanism and Effect of Ru‐Doping

LaNiO₃ perovskite is an interesting precursor for Ni/La₂O₃ catalysts for the dry reforming of methane at high temperatures. Precursors have been synthesized by co‐precipitation without, with 2.5 at %, and with 5 at % Ru doping. The presence of Ru leads to a stabilization of the perovskite structure and hinders the decomposition into NiO and Ruddlesden‐Popper mixed oxides La_n+1Ni_nO_3n+1, which was observed for the Ru‐free sample upon calcination at 1000 °C (n = 3). Upon reduction in hydrogen, a mechanism involving at least two steps was observed and the first major step was identified as the partial reduction of the precursor leading to a LaNiO_2.5‐like intermediate. The second major step is the reduction to Ni metal supported on La₂O₃ independent of the Ru content of the catalyst. In the presence of Ru, indications for Ni‐Ru alloy formation and for a higher dispersion of the metallic phase were found. The catalytic activity in DRM of the catalyst containing 2.5 % Ru was superior to the catalysts with more or without Ru. Furthermore, the propensity of coke formation was reduced by the presence of Ru.     

Characterization of La-promoted Ni/Al2O3 catalysts for hydrogen production from glycerol dry reforming

In the current paper, dry (CO₂)-reforming of glycerol, a new reforming route, was carried out over alumina (Al₂O₃)-supported, non-promoted and lanthanum-promoted nickel (Ni) catalysts. Both sets of catalysts were synthesized via a wet co-impregnation procedure. Physicochemical characterization of the catalysts showed that the promoted catalyst possessed smaller metal crystallite size, hence higher metal dispersion compared to the virgin Ni/Al₂O₃ catalyst. This was also corroborated by the surface images captured by the FESEM analysis. From temperature-programmed calcination analysis, the derivative weight profiles revealed two peaks, which represent a water elimination peak at a temperature range of 373 to 473 K followed by nickel nitrate decomposition from 473 to 573 K. In addition, BET surface area measurements gave 85.0 m²·g⁻¹ for the non-promoted Ni catalyst, whilst the promoted catalysts showed an average of 1% to 6% improvement depending on the La loadings. Significantly, reaction studies at 873 K showed that glycerol dry reforming successfully produced H₂. The 2%La-Ni/Al₂O₃ catalyst, which possessed the largest BET surface area, gave an optimum H₂ generation (9.70%) at a glycerol conversion of 24.5%.     

Activity of Ni catalysts for hydrogen production via biomass pyrolysis

Ni catalysts were tested in the catalytic pyrolysis of biomass. The influence of Ni loading and various catalytic supports (ZrO₂, Al₂O₃, ZrO₂ + Al₂O₃, CeO₂, SiO₂) was studied. Although the gas phase was the main object of this study, solid and liquid residues were tested as well (mainly by TOC and GC-MS methods). Activity tests were performed in a batch reactor with mechanical stirring, equipped with on-line GC. Reaction was conducted at 700°C, with ??-cellulose as a biomass model and with waste paper as an example of raw lignocellulosic material. Reactions in the presence of a catalyst gave a higher hydrogen yield. The most promising results were obtained with Ni/ZrO₂.     

钙铝石涂层对整体型钙钛矿氧化物催化剂活性和热稳定性的影响

 采用固相反应法合成了钙铝石材料 12SrO•7Al2O3, 并以此作为涂层制备了堇青石蜂窝陶瓷型 La0.8Sr0.2MnO3 整体催化剂, 在不同温度 (850~1 050 oC) 下对该催化剂进行了热处理, 并采用 N2 吸附-脱附、X 射线衍射和扫描电镜等手段对其进行了表征, 考察了其催化甲基丙烯酸甲酯燃烧反应的活性. 结果表明, 12SrO•7Al2O3 作为涂层明显改善了整体催化剂的热稳定性, 在 850 oC 下焙烧 6 h 后, 含有 12SrO•7Al2O3 涂层的整体催化剂在 260 oC 即可将甲基丙烯酸甲酯完全转化. 12SrO•7Al2O3 涂层可避免 La0.8Sr0.2MnO3 活性组分与堇青石的接触, 减轻了活性组分在催化剂表面的烧结, 有利于保持 La0.8Sr0.2MnO3 活性组分的晶体结构和分散度, 提高整体催化剂的活性和热稳定性.