Porous Cu-NiO modified glass carbon electrode enhanced nonenzymatic glucose electrochemical sensors

Porous Cu-NiO nanocomposites were successfully prepared by calcination of the Cu-Ni(OH)(2) precursor at 400 °C for 2 h. During the process of calcination, Ar was used to deaerate O(2). The structure and morphology of Cu-NiO were characterized by X-ray diffraction spectrum (XRD), energy dispersive X-ray analyses (EDX), transmission electron microscopy (TEM), and scanning electron microscopy (SEM). Using porous Cu-NiO nanocomposites, a simple non-enzymatic amperometric sensor has been fabricated (Cu-NiO/GCE) and evaluated by electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and typical amperometric method. When applied to detect glucose by the amperometric method, Cu-NiO/GCE produced an ultrahigh sensitivity of 171.8 μA mM(-1), with a low detection limit of 0.5 μM (S/N = 3). What's more, interference from common co-existing species, such as UA, AA, and fructose can be avoided at the sensor. Results in this study imply that porous Cu-NiO nanocomposites are promising nanomaterials for the enzyme-free determination of glucose.     

PANI–TiC nanocomposite film for the direct electron transfer of hemoglobin and its application for biosensing

A novel polyaniline and titanium carbide (PANI–TiC) nanocomposite was synthesized by an in situ chemical oxidative polymerization method, and a hydrogen peroxide (H₂O₂) biosensor was fabricated by PANI–TiC with hemoglobin (Hb)-modified glassy carbon electrode (GCE). Scanning electron microscope and energy dispersive X-ray spectroscopy showed the morphology and ingredient of PANI–TiC. Electrochemical investigation of the biosensor showed a pair of well-defined, quasi-reversible redox peaks with E _pa?=??0.318 V and E _pc?=??0.356 V (vs SCE) in 0.1 M, pH 7.0 sodium phosphate-buffered saline at the scan rate of 150 mV s^?1. Transfer rate constant (k _s) was 2.01 s^?1. The Hb/PANI–TiC/GCE showed a good electrochemical catalytic response for the reduction of H₂O₂ with the linear range from 0.5 to 285.5 μM and the detection limit of 0.2 μM (S/N?=?3). The apparent Michaelis–Menten constant (K _m) was estimated to be 1.21 μM. Therefore, the PANI–TiC as a novel matrix opened up a further possibility for study on the design of enzymatic biosensors with potential applications.     

Amperometric ascorbic acid biosensor based on carbon nanoplatelets derived from ground cherry husks

In this work, a novel amperometric biosensor based on carbon nanoplatelets derived from ground cherry (Physalis peruviana) husks (GCHs-CNPTs) is reported for the sensitive and selective detection of ascorbic acid (AA). The structure of the nanoplatelets, the oxygen-containing groups and edge-plane-like defective sites (EPDSs) on the GCHs-CNPTs were characterized by scanning electron microscopy, X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. The presence of GCHs-CNPTs with a high density of EPDSs effectively enhances the electron transfer between AA and the glassy carbon electrode (GCE), and thus induces a substantial decrease in the overvoltage for AA oxidation compared with both a bare GCE and a GCE modified with carbon nanotubes (CNTs/GCE). In particular, an amperometric biosensor based on GCHs-CNPTs exhibited a wider linear range (0.01–3.57 mM), higher sensitivity (208.63 μA mM^− 1 cm^− 2), a lower detection limit (1.09 μM, S/N = 3) and better resistance to fouling for AA determination compared to a CNTs/GCE. The great potential of the GCHs-CNPTs/GCE for practical and reliable AA analysis was demonstrated by the successful determination of AA in samples taken from a medical injection dose and a soft drink.     

A MnOOH‐Polyaniline Nanocomposite Modified Gold Electrode for Electrochemical Sensing of Nitrite

A novel non‐enzymatic nitrite sensor was fabricated by immobilizing MnOOH‐PANI nanocomposites on a gold electrode (Au electrode). The morphology and composition of the nanocomposites were investigated by transmission electron microscopy (TEM ) and Fourier transform infrared spectrum (FTIR ). The electrochemical results showed that the sensor possessed excellent electrocatalytic ability for NO₂⁻ oxidation. The sensor displayed a linear range from 3.0 μmol•L⁻¹ to 76.0 mmol•L⁻¹ with a detection limit of 0.9 μmol•L⁻¹ (S/N = 3), a sensitivity of 132.2 μA •L•mol⁻¹•cm⁻² and a response time of 3 s. Furthermore, the sensor showed good reproducibility and long‐term stability. It is expected that the MnOOH‐PANI nanocomposites could be applied for more active sensors and used in practice for nitrite sensing.     

Synthesis and Electrochemical Investigation of Tetra Amino Cobalt (II) Phthalocyanine Functionalized Polyaniline Nanofiber for the Selective Detection of Dopamine

A new electrochemical sensing platform based on tetra‐amino cobalt (II) phthalocyanine (TACoPc) ingrained polyaniline (PANI) nanofiber composite (TACoPc/PANI hybrid) has been developed for the selective detection of dopamine. The uniform fibrous network of PANI/TACoPc hybrid was synthesized by a one‐step oxidative polymerization at room temperature. The synthesized nanocomposite was characterized using field emission scanning electron microscopy (FESEM), energy dispersive X‐ray (EDX), fourier transmission infrared spectroscopy (FTIR), raman spectroscopy, X‐ray diffraction (XRD) and UV‐Visible spectroscopy. The electrochemical behavior of the TACoPc/PANI hybrid material was studied by using different electrochemical techniques, including cyclic voltammetry (CV) and chronoamperometry in 0.1 M phosphate buffer solution (PBS) of pH 7 by modifying the glassy carbon electrode (GCE). Due to the synergistic impact of PANI and TACoPc, the suggested altered electrode provided superior catalytic performance for dopamine even in the presence of ascorbic acid. It exhibited a linear reaction with a high sensitivity of 1.212 μA/μM cm^?2 and a low detection limit of 0.064 μM over the 20–200 μM concentration range in 0.1 M PBS. One of the commonly faced problems of interference of ascorbic acid and uric acid in the electrochemical detection of dopamine was completely excluded from this modified electrode which led to an increase in the catalytic activity of the material for the detection of dopamine in the presence of ascorbic acid.     

Enzyme-free impedimetric glucose sensor based on gold nanoparticles/polyaniline composite film

A non-enzymatic impedimetric glucose sensor was fabricated based on the adsorption of gold nanoparticles (GNPs) onto conductive polyaniline (PANI)-modified glassy carbon electrode (GCE). The modified electrode (GCE/PANI/GNPs) was characterized by using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and scanning electron microscopy (SEM). The determination of glucose concentration was based on the measurement of EIS with the mediation of electron transfer by ferricyanide ([Fe(CN)₆]^3?). The [Fe(CN)₆]^3? is reduced to ferrocyanide ([Fe(CN)₆]^4?), which in turn is oxidized at GCE/PANI/GNPs. An increase in the glucose concentration results in an increase in the diffusion current density of the [Fe(CN)₆]^4? oxidation, which corresponds to a decrease in the faradaic charge transfer resistance (R _ct). A wide linear concentration range from 0.3 to 10 mM with a lower detection limit of 0.1 mM for glucose was obtained. The proposed sensor shows high sensitivity, good reproducibility, and stability. In addition, the sensor exhibits no interference from common interfering substances such as ascorbic acid, acetaminophen, and uric acid.     

A sandwich-type DNA biosensor based on electrochemical co-reduction synthesis of graphene-three dimensional nanostructure gold nanocomposite films

A novel electrochemical DNA biosensor based on graphene-three dimensional nanostructure gold nanocomposite modified glassy carbon electrode (G-3D Au/GCE) was fabricated for detection of survivin gene which was correlated with osteosarcoma. The G-3D Au film was prepared with one-step electrochemical coreduction with graphite oxide and HAuCl₄ at cathodic potentials. The active surface area of G-3D Au/GCE was 2.629 cm², which was about 3.8 times compared to that of a Au-coated GCE under the same experimental conditions, and 8.8 times compared to a planar gold electrode with a similar geometric area. The resultant nanocomposites with high conductivity, electrocatalysis and biocompatibility were characterized by scanning electron microscopy (SEM), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). A “sandwich-type” detection strategy was employed in this electrochemical DNA biosensor and the response of this DNA biosensor was measured by CV and amperometric current–time curve detection. Under optimum conditions, there was a good linear relationship between the current signal and the logarithmic function of complementary DNA concentration in a range of 50–5000 fM with a detection limit of 3.4 fM. This new biosensor exhibited a fast amperometric response, high sensitivity and selectivity and has been used in a polymerase chain reaction assay of real-life sample with a satisfactory result.     

SiO2 coated Fe3O4 magnetic nanoparticle dispersed multiwalled carbon nanotubes based amperometric glucose biosensor

A new type of amperometric glucose biosensor based on silicon dioxide coated magnetic nanoparticle decorated multiwalled carbon nanotubes (Fe₃O₄@SiO₂/MWNTs) on a glassy carbon electrode (GCE) has been developed. MWNTs have been synthesized by catalytic chemical vapour decomposition (CCVD) of acetylene over rare earth (RE) based AB₃ alloy hydride catalyst. The as-grown MWNTs have been purified and further functionlized. Functionalized MWNTs have been decorated with magnetic Fe₃O₄ nanoparticles which have been uniformly coated with biocompatible SiO₂ using a simple chemical reduction method. The characterization of magnetic nanoparticle modified MWNTs have been done by X-ray diffraction (XRD), Fourier transform infra red spectroscopy (FT-IR), scanning electron microscope (SEM), transmission electron microscope (TEM), vibrating sample magnetometer (VSM), energy dispersive X-ray analysis (EDX) and UV-vis spectroscopy. Amperometric biosensor has been fabricated by the deposition of glucose oxidase (GOD) over Nafion-solubilized Fe₃O₄@SiO₂/MWNTs electrode. The resultant bioelectrode retains its biocatalytic activity and offers fast and sensitive glucose quantification. The performance of the biosensor has been studied using cyclic voltammetry and amperometry and the results have been discussed. The fabricated glucose biosensor exhibits a linear response from 1 μM to 30 mM with an excellent detection limit of 800 nM indicating the potential applications in food industries.     

In situ chemo-synthesized multi-wall carbon nanotube-conductive polyaniline nanocomposites: characterization and application for a glucose amperometric biosensor

A new glucose amperometric biosensor, based on electrodeposition of platinum nanoparticles onto the surface of multi-wall carbon nanotube (MWNT)-polyaniline (PANI) nanocomposites, and then immobilizing glucose oxidase (GOD) with covalent interaction and adsorption effect, was constructed in this paper. Firstly, the MWNT-PANI nanocomposites had been synthesized by in situ polymerization and were characterized through transmission electron microscopy (TEM), Fourier transform infrared (FT-IR) spectroscopy, and ultraviolet and visible (UV-vis) absorption spectra. The assembled process of the modified electrode was probed by scanning electron microscopy (SEM) and cyclic voltammetry (CV). Chronoamperometry was used to study the electrochemical performance of the resulting biosensor. The glucose biosensor exhibited a linear calibration curve over the range from 3.0 μM to 8.2 mM, with a detection limit of 1.0 μM and a high sensitivity of 16.1 μA mM⁻¹. The biosensor also showed a short response time (within 5 s). Furthermore, the reproducibility, stability and interferences of the biosensor were also investigated.     

Bird nest-like zinc oxide nanostructures for sensitive electrochemical glucose biosensor

In this research, a novel bird nest-like zinc oxide (BN-ZnO) nanostructures were prepared by a simple solvothermal method. A sensitive electrochemical glucose biosensor was for the first time developed based on the immobilization of glucose oxidase (GOx) on nanostructured BN-ZnO modified electrode. The BN-ZnO nanostructure and the resultant biosensor were characterized by scanning electron microscope, X-ray diffraction spectroscopy, Fourier transform infrared spectroscopy, and electrochemical impedance spectroscopy. BN-ZnO nanostructures have large specific surface area and can load large amounts of GOx molecules. Meanwhile, BN-ZnO provides an excellent microenvironment to retain the native bioactivity of enzymes and to promote direct electron transfer between GOx and electrode surface. The proposed biosensor shows a wide linear range of 0.005–1.6 mmol/L, high sensitivity of 15.6 mA L mol⁻¹ cm⁻² with a low detection limit of 0.004 mmol/L. The resulting biosensor also shows excellent selectivity, acceptable stability and reproducibility, and can be successfully applied in the detection of glucose in human serum samples at −0.37 V.     

A Single Drop Fabrication of the Cholesterol Biosensor Based on Synthesized NiFe2O4NPs Dispersed on PDDA‐CNTs

A cholesterol biosensor based on cholesterol oxidase‐poly(diallyldimethylammonium chloride)‐carbon nanotubes‐nickel ferrite nanoparticles (ChOx‐PDDA‐CNTs‐NiFe₂O₄NPs) solution is easily fabricated by using a single dropping step on a glassy carbon electrode (GCE) surface. This technique is an alternative way to reduce complexity, cost and time to produce the biosensor. The uniformly dispersed materials on the electrode surface enhance the catalytic reaction of cholesterol oxidase and electron transfer from the oxidation of hydrogen peroxide in the system. The nickel ferrite nanoparticles were synthesized by co‐precipitation and calcination at various temperatures. These nanoparticles were then characterized using field emission scanning electron microscopy (FE‐SEM), energy‐dispersive X‐ray spectroscopy (EDX), Fourier transform infrared spectroscopy (FTIR), cyclic voltammetry (CV) and X‐ray diffraction (XRD). The synthesized material calcined at 700 °C was well defined and presented the octahedral metal stretching with cubic NiFe₂O₄NPs phase. In cyclic voltammetric study, the ChOx‐PDDA‐CNTs‐NiFe₂O₄NPs/GCE showed 0.43 s⁻¹ charge transfer rate constant (K _s), 7.79×10⁻⁶ cm² s⁻¹ diffusion coefficient value (D ), 0.13 mm² electroactive surface area (A _e) and 3.58×10⁻⁸ mol cm⁻² surface concentration ( ). This modified electrode exhibits stability in term of percent relative standard deviation (%RSD=0.62 %, n=10), reproducibility (%RSD=0.81, n=10), high sensitivity (25.76 nA per mg L⁻¹ cm⁻²), linearity from 1 to 5,000 mg L⁻¹ (R²=0.998) with a low detection limit (0.50 mg L⁻¹). Its Michaelis‐Menten constant (K _m) was 0.14 mM with 0.92 μA maximum current (I _max) and demonstrated good selectivity without the effects of electroactive species such as ascorbic acid, glucose and uric acid. The cholesterol biosensor was successfully applied to determine cholesterol levels in human blood samples, showing promise due to its simplicity and availability.     

Direct electrochemistry of hemoglobin on graphene/Fe3O4 nanocomposite-modified glass carbon electrode and its sensitive detection for hydrogen peroxide

Graphene/Fe₃O₄ nanocomposite was prepared for the immobilization of hemoglobin (Hb) to improve the electron transfer between Hb and glass carbon electrode (GCE). The characterization of nanocomposites was described by transmission electron microscopy, Fourier transform infrared, Raman spectroscopy, and X-ray photoelectron spectroscopy, respectively. The electrochemistry of Hb on the graphene/Fe₃O₄-based GCE was investigated by cyclic voltammetry and amperometric measurement. The modified electrode showed a wide linear range from 0.25 μmol/L to 1.7 mmol/L with a correlation coefficient of 0.9967. The detection limit of the H₂O₂ biosensor was estimated at 6.0?×?10^?6?mol/L at a signal-to-noise ratio of 3.     

A Novel Enzymatic Glucose Biosensor and Nonenzymatic Hydrogen Peroxide Sensor Based on (3‐Aminopropyl) Triethoxysilane Functionalized Reduced Graphene Oxide

In the present study, a novel enzymatic glucose biosensor using glucose oxidase (GOx) immobilized into (3‐aminopropyl) triethoxysilane (APTES) functionalized reduced graphene oxide (rGO‐APTES) and hydrogen peroxide sensor based on rGO‐APTES modified glassy carbon (GC) electrode were fabricated. Nafion (Nf) was used as a protective membrane. For the characterization of the composites, Fourier transform infrared spectroscopy (FTIR), X‐ray powder diffractometer (XRD), and transmission electron microscopy (TEM) were used. The electrochemical properties of the modified electrodes were investigated using electrochemical impedance spectroscopy, cyclic voltammetry, and amperometry. The resulting Nf/rGO‐APTES/GOx/GC and Nf/rGO‐APTES/GC composites showed good electrocatalytical activity toward glucose and H₂O₂, respectively. The Nf/rGO‐APTES/GC electrode exhibited a linear range of H₂O₂ concentration from 0.05 to 15.25 mM with a detection limit (LOD) of 0.017 mM and sensitivity of 124.87 μA mM⁻¹ cm⁻². The Nf/rGO‐APTES/GOx/GC electrode showed a linear range of glucose from 0.02 to 4.340 mM with a LOD of 9 μM and sensitivity of 75.26 μA mM⁻¹ cm⁻². Also, the sensor and biosensor had notable selectivity, repeatability, reproducibility, and storage stability.     

A New Amperometric Hydrazine Sensor Based on Prussian Blue/Single‐walled Carbon Nanotube Nanocomposites

A slow reaction process has been successfully used to synthesize Prussian blue/single‐walled carbon nanotubes (PB/SWNTs) nanocomposites. Electrochemical and surface characterization by cyclic voltammetry (CV), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV‐vis absorption spectroscopy, Fourier transform infrared (FTIR) spectroscopy and X‐ray diffraction (XRD) confirmed the presence of PB nanocrystallites on SWNTs. PB/SWNTs modified glassy carbon electrode (GCE) exhibits efficient electron transfer ability and high electrochemical response towards hydrazine. The fabricated hydrazine sensor showed a wide linear range of 2.0×10^?6–6.0×10^?3 M with a response time less than 4 s and a detection limit of 0.5 μM. PB/SWNTs modified electrochemical sensors are promising candidates for cost‐effective in the hydrazine assays.     

A novel electrochemical sensor for determination of hydroquinone in water using FeWO4/SnO2 nanocomposite immobilized modified glassy carbon electrode

A novel electrochemical sensor based on iron tungstate doped tin oxide nanocomposite Nafion (FeWO₄/SnO₂/Nf) immobilized modified glassy carbon electrode (GCE) is fabricated to determine hydroquinone (HQ) in this present study. The structural morphology and phase of FeWO₄/SnO₂ nanocomposite are characterized by X-ray powder diffraction (XRD), energy dispersive X-ray analysis (EDX), Fourier transform infrared spectroscopy (FT-IR), high transmission electron microscopy (HR-TEM) and Field emission scanning electron microscopy (FE-SEM), Brunauer-Emmett-Teller (BET) and X-ray photoelectron spectroscopy (XPS) respectively. Electrochemical methods such as cyclic voltammetry (CV), difference pulse voltammetry (DPV) and amperometric (i-t curve) are used to describe the electrochemical performance of the surface modified electrode for HQ sensing studies. The FeWO₄/SnO₂/Nf immobilized GCE is exhibited excellent catalytic activity with the increasing current signal during HQ sensing. The linear range of response is obtained between 0.01 µM and 50 µM for HQ detection under optimized conditions and the low detection limit (LOD) is found to be 0.0013 µM. Moreover, the present modified electrode shows good reproducibility and excellent anti-interference behavior. In addition, the present electrochemical sensor is applied to the real samples of collected waters from various sources and the obtained experimental results are quite satisfactory.     

Electrodeposition of Three‐Dimensional Porous Platinum Film on Removable Polyaniline Template for High‐Performance Electroanalysis

Three‐dimensional porous platinum (Pt_por) films are prepared based on Pt electrodeposition on polyaniline (PANI) modified electrodes followed by selective dissolution of PANI with HNO₃. Electrochemical quartz crystal microbalance data suggest that the PANI‐H₂PtCl₆ interaction involves redox and coordination reactions, depending on the working potential. The Pt_por shows better electrocatalytic performance than the Pt/PANI and conventionally electrodeposited Pt. The Pt_por modified glassy carbon electrode (GCE) can electrocatalyze the oxidation of H₂O₂ with a sensitivity of 414 µA cm^?2 mM^?1 and a detection limit of 9 nM, and the chitosan‐glucose oxidase/Pt_por/GCE can sense glucose with a sensitivity of 93.4 µA cm^?2 mM^?1.     

Ternary Ag/Polyaniline/Au nanocomposites: Preparation,characterization and electrochemical properties

Ternary Ag/Polyaniline/Au nanocomposites were synthesized successfully by immobilizing of Au nanoparticles (NPs) on the surface of Ag/Polyaniline (PANI) nanocomposites. Ag/PANI nanocomposites were prepared via in situ chemical polymerization of aniline in the presence of 4-aminothiophenol (4-ATP) capped silver colloidal NPs. Then, uniform gold (Au) NPs were assembled on the surface of resulted Ag/PANI nanocomposites through electrostatic interaction to get Ag/Polyaniline/Au nanocomposites. The nanocomposites were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), ultraviolet visible spectroscopy (UV-Vis), thermogravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR). Moreover, Ag/PANI/Au nanocomposites were immobilized on the surface of a glassy carbon electrode and showed enhanced electrocatalytic activity for the reduction of H₂O₂ compared with Ag/PANI.     

A Novel Bioelectrochemical Sensor Based on Immobilized Urease on the Surface of Nickel Oxide Nanoparticle and Polypyrrole Composite Modified Pt Electrode

Nickel oxide nanoparticle (NiO?NP) and polypyrrole (PPy) composite were deposited on a Pt electrode for fabrication of a urea biosensor. To develop the sensor, a thin film of PPy?NiO composite was deposited on a Pt substrate that serves as a matrix for the immobilization of enzyme. Urease was immobilized on the surface of Pt/PPy?NiO by a physical adsorption. The response of the fabricated electrode (Pt/PPy?NiO/Urs) towards urea was analyzed by chronoamperometry and cyclic voltammetry (CV) techniques. Electrochemical response of the bio‐electrode was significantly enhanced. This is due to electron transfer between Ni²⁺ and Ni³⁺ as the electro‐catalytic group and the reaction between polypyrrole and the urease‐liberated ammonium. The fabricated electrode showed reliable and demonstrated perfectly linear response (0.7–26.7 mM of urea concentration, R²= 0.993), with high sensitivity (0.153 mA mM^?1 cm^?2), low detection of limit (1.6 μM), long stability (10 weeks), and low response time (～5 s). The developed biosensor was highly selective and obtained data were repeatable and reproduced using PPy‐NiO composite loaded with immobilized urease as urea biosensors.     

Synthesis of Ag Nanoparticle Doped MnO2/GO Nanocomposites at a Gas/Liquid Interface and its Application in H2O2 Detection

Ag/MnO₂/GO nanocomposites were synthesized via the method of gas/liquid interface based on silver mirror reaction, and a non‐enzymatic H₂O₂ sensor was fabricated through immobilizing Ag/MnO₂/GO nanocomposites on GCE. The composition and morphology of the nanocomposites were studied by energy‐dispersive X‐ray spectroscopy (EDS), X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). Electrochemical investigation indicated that it exhibited a favorable performance for the H₂O₂ detection. Its linear detection range was from 3 μM to 7 mM with a correlation coefficient of 0.9960; the sensitivity was 105.40 μA mM^?1 cm^?2 and the detection limit was estimated to be 0.7 μM at a signal‐to‐noise ratio of 3.     

Fabrication of a novel glucose biosensor based on a highly electroactive polystyrene/polyaniline/Au nanocomposite

A novel nanocomposite with a core-shell structure containing polystyrene (PS), polyaniline (PANI), and Au nanoparticles (NPs) was synthesized. The nanocomposite was characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FTIR). Cyclic voltammetric experiments indicated that the nanocomposite had excellent redox ability in a wide range of pH values. The existence of Au NPs resulted in a higher electrical conductivity of the nanocomposite. As a model, glucose oxidase (GOD) was entrapped onto the nanocomposite-modified glassy carbon electrode (GCE) and applied to construct a sensor. The immobilized GOD showed a pair of well-defined redox peaks and high catalytic activity for the oxidation of glucose.