Aerosol-assisted fabrication of mesoporous titania spheres with crystallized anatase structures and investigation of their photocatalitic properties

We demonstrate practical aerosol-assisted approach to synthesize spherical mesoporous titania particles with high surface areas. Scanning electron microscopy observation of the spray-dried products clearly shows spherical morphology. To remove surfactants and enhance crystallinity, the spray-dried products are calcined under various temperatures. The crystalline structures inside the particles are carefully detected by wide-angle XRD measurements. With increase of the calcination temperatures, anatase crystal growth proceeds and transformation from anatase to rutile is occurred. The effect of various calcination temperatures on the mesostructures is also studied by using N₂ adsorption desorption isotherms. The mesoporous titania particles calcined at 350, 400, and 500 °C exhibit type IV isotherms with a capillary condensation step and shows a hysteresis loop, which is a characteristic of mesoporous materials. The reduction in the surface areas and the pore volumes is confirmed by increasing the calcination temperatures, while the average pore diameters are increased gradually. This is attributed to the distortion of the mesostructures due to the grain growth of the anatase phase and the transformation to the rutile phase during the calcination process. As a preliminary experimental photocatalytic activity, oxidative decomposition of acetaldehyde under UV irradiation is examined. The mesoporous titania calcined at 400 °C shows the highest photocatalytic activity, due to both high surface area and well-developed anatase crystalline phase.     

Large-scale preparation of ordered titania nanorods with enhanced photocatalytic activity

A titania layer with ordered nanostructures is expected to be of high photocatalytic activity due mainly to its high specific surface area. In the present work, large-area films with ordered titania nanorods were deposited on titanium substrates through a solution approach. The nanorods, with the phase composition of a mixture of anatase and rutile, grew on top of a condensed anatase interlayer along mainly the rutile [001]-axis. The photocatalytic activity was evaluated by decomposing rhodamine B in water and compared with the general sol-gel derived titania films and a commercial DP-25 titania coating. It is found that the as-deposited titania nanorods exhibited extremely high initial photocatalytic activity but declined to a poor value after the consumption of beneficial oxidative peroxo complexes coordinated to Ti(IV). A subsequent thermal treatment eliminated such complexes but at the same time improved the crystallinity of the titania nanorods. The photocatalytic activity of the thermally treated titania nanorods was stable and significantly higher than that of the sol-gel derived film and commercial DP-25 coating.     

Visible light photocatalyst: iodine-doped mesoporous titania with a bicrystalline framework

Iodine-doped (I-doped) mesoporous titania with a bicrystalline (anatase and rutile) framework was synthesized by a two-step template hydrothermal synthesis route. I-doped titania with anatase structure was also synthesized without the use of a block copolymer as a template. The resultant titania samples were characterized by X-ray diffraction, Raman spectroscopy, Fourier transform infrared, nitrogen adsorption, transmission electron microscopy, X-ray photoelectron spectroscopy, and UV-visible absorption spectroscopy. Both I-doped titania samples, with and without template, show much better photocatalytic activity than commercial P25 titania in the photodegradation of methylene blue under the irradiation of visible light (>420 nm) and UV-visible light. Furthermore, I-doped mesoporous titania with a bicrystalline framework exhibits better activity than I-doped titania with anatase structure. The effect of rutile phase in titania on the adsorptive capacity of water and surface hydroxyl, and photocatalytic activity was investigated in detail. The excellent performance of I-doped mesoporous titania under both visible light and UV-visible light can be attributed to the combined effects of bicrystalline framework, high crystallinity, large surface area, mesoporous structure, and high visible light absorption induced by I-doping.     

Enhanced photoactivity of neodymium doped mesoporous titania synthesized through aqueous sol–gel method

Nanosize neodymium doped titania has been prepared by hydrolysis of titanium oxychloride followed by peptisation under acidic condition. The anatase to rutile phase transformation temperature was found to increase by 150 °C as a result of neodymium doping. The doped sample shows 10 times higher surface area than the undoped one after calcining at 700 °C. All the samples calcined at 500, 600 and 700 °C show type IV isotherm, which is characteristic of mesoporous material. The pore size distribution curves also show that the pores are in mesoporous region. Further, the neodymium doped titania shows increased photoactivity than the undoped titania with respect to decomposition of methylene blue when subjected to UV light. The transmission electron micrograph indicates that a nanocrystalline doped titania is obtained through the present method. The effect of neodymium doping on the anatase phase stability, specific surface area and photoactivity are reported.     

Precise Size Control over Ultrafine Rutile Titania Nanocrystallites in Hierarchical Nanotubular Silica/Titania Hybrids with Efficient Photocatalytic Activity

Hierarchical‐structured nanotubular silica/titania hybrids incorporated with particle‐size‐controllable ultrafine rutile titania nanocrystallites were realized by deposition of ultrathin titania sandwiched silica gel films onto each nanofiber of natural cellulose substances (e.g., common commercial filter paper) and subsequent flame burning in air. The rapid flame burning transforms the initially amorphous titania into rutile phase titania, and the silica gel films suppress the crystallite growth of rutile titania, thereby achieving nano‐precise size regulation of ultrafine rutile titania nanocrystallites densely embedded in the silica films of the nanotubes. The average diameters of these nanocrystallites are adjustable in a range of approximately 3.3–16.0 nm by a crystallite size increment rate of about 2.4 nm per titania deposition cycle. The silica films transfer the electrons activated by crystalline titania and generate catalytic reactive species at the outer surface. The size‐tuned ultrafine rutile titania nanocrystallites distributed in the unique hierarchical networks significantly improve the photocatalytic performance of the rutile phase titania, thereby enabling a highly efficient photocatalytic degradation of the methylene blue dye under ultraviolet light irradiation, which is even superior to the pure anatase‐titania‐based materials. The facile stepwise size control of the rutile titania crystallites described here opens an effective pathway for the design and preparation of fine‐nanostructured rutile phase titania materials to explore potential applications.     

Synthesis of Titanium Dioxide Nanoparticles for Photocatalytic Degradation of Cyanide in Wastewater

Cyanide is highly toxic, and although various approaches have been employed for its remediation, these methods do not have the required performance. This report describes the synthesis of titanium dioxide nanoparticles with maximum photocatalytic properties and their application for the treatment of cyanide in wastewater. Three types of crystalline titanium nanoparticles were synthesized: anatase, rutile, and a biphasic mix of rutile and anatase. The phase and microscopic properties were characterized by X-ray diffraction and scanning electron microscopy. The specific surfaces of the particles were determined, and their photocatalytic activity was studied under the ultraviolet irradiation for cyanide degradation. The results indicate that an increase in sulfate ion leads to changes in the phase ratios of rutile to anatase. The diameter of the nanoparticles was between 18 and 22 nm, and they displayed high photocatalytic properties. The biphasic form of the titanium dioxide nanoparticles demonstrated the highest removal of cyanide. Complete degradation of cyanide was observed in a pilot scale experiment.     

Hierarchical‐Structured Anatase‐Titania/Cellulose Composite Sheet with High Photocatalytic Performance and Antibacterial Activity

Bulk hierarchical anatase‐titania/cellulose composite sheets were fabricated by subjecting an ultrathin titania gel film pre‐deposited filter paper to a solvo‐co‐hydrothermal treatment by using titanium butoxide as the precursor to grow anatase‐titania nanocrystallites on the cellulose nanofiber surfaces. The titanium butoxide specie is firstly absorbed onto the nanofibers of the cellulose substance through a solvothermal process, which was thereafter hydrolyzed and crystallized upon the subsequent hydrothermal treatment, leading to the formation of fine anatase‐titania nanoparticles with sizes of 2–5 nm uniformly anchored on the cellulose nanofibers. The resulting anatase‐titania/cellulose composite sheet shows a significant photocatalytic performance towards degradation of a methylene blue dye, and introduction of silver nanoparticles into the composite sheet yields an Ag‐NP/anatase‐titania/cellulose composite material possessing excellent antibacterial activity against both Gram‐positive and Gram‐negative bacteria.     

Preparation of nano and microcrystals of silver using titania xerogel matrix as template

Ag-doped TiO₂ wet gels were prepared by sol?Cgel process using a mixture of titanium isopropoxide and silver nitrate as precursor solution, with Ag:Ti molar ratio of 1:6. After drying, the titanium oxide xerogels were used as template in the preparation of nano and microcrystals of metallic silver. The porous network and the structure of the titania matrix influenced the type and distribution of silver crystal produced on the composite surface. Silver nanoparticles segregated to the surface of titania xerogel during the heating step, giving rise to nanocrystals that coalesced forming microcrystals with different shapes and faceting. The microcrystals grew on the composite surface, reaching sizes between 5 and 20 microns and self-organized of different ways. The xerogel heated at 600 °C formed by anatase, rutile and silver nanoparticles exhibited considerable photocatalytic activity to degrade methylene blue.     

MCM-41分子筛担载纳米TiO2复合材料光催化降解罗丹明B

采用溶胶-凝胶法将TiO2担载在介孔MCM-41分子筛上, 制备了不同TiO2含量的系列TiO2/MCM-41复合材料, 利用X射线衍射、N2吸附、紫外-可见光谱和透射电镜等方法对其进行表征. TiO2的晶型为锐钛矿相, 复合材料的比表面积和孔体积随其中TiO2担载量(复合材料中TiO2与MCM-41的质量比)的增加而减小, TiO2的平均粒径随其担载量的增加而增大. 以罗丹明B的光催化降解为探针反应, 评价了TiO2/MCM-41复合材料的光催化降解活性. 结果表明, 在紫外光照射下, 罗丹明B在该复合材料上的光催化降解反应遵循一级反应动力学, 复合材料对罗丹明B的光催化降解活性明显高于商用TiO2 (P-25), 复合材料的光催化降解活性由复合材料的吸附能力和所含TiO2的光催化活性共同决定.     

Enhanced photocatalytic activity for titanium dioxide by co-modification with copper and iron

A copper(II) and iron(III) co-modified titanium dioxide nano material was prepared by a simple sol–gel process using titanium(IV) isopropoxide plus copper(II) and iron(III) nitrates as raw materials. The as-prepared nanocomposites were characterized by X-ray diffraction (XRD), diffuse reflectance spectroscopy and photoluminescence spectra. The XRD results showed that the undoped TiO₂ nanoparticles mainly include anatase phase while the Cu, Fe-codoped TiO₂ nanoparticles showed a mixture of anatase phase with a small fraction of rutile phase displaying higher activity than the pure anatase phase. Optical characterization showed that the codoping with copper(II) and iron(III) resulted in a red shift of adsorption and lower recombination probability between electrons and holes, which were associated with high photocatalytic activity of the Cu, Fe-codoped TiO₂ nanoparticles under visible light (λ > 400 nm). The photocatalytic activity of the samples was tested by aqueous methyl orange degradation. The capability of the codoped catalyst was much higher than that of the pure TiO₂ catalyst under visible irradiation. A mechanism is proposed in order to account for the enhanced catalytic activity.     

Hydrothermal synthesis, characterization, and photocatalytic performance of silica-modified titanium dioxide nanoparticles

Silica-modified titanium dioxides were prepared by a hydrothermal method and then characterized by XRD, FT-IR, XPS, TEM, and UV-visible spectroscopy. The silica-modified titanium dioxides were in anatase phase and had large surface areas. There was strong interaction between SiO2 and TiO2, and TiOSi bonds formed during the hydrothermal process. The addition of silica in TiO2 particles could effectively suppress the formation of the rutile phase and the growth of titanium dioxide crystals. DRS spectra proved an increase in the band-gap transition with the increase of silica. The silica-modified TiO2 nanoparticles exhibited better photocatalytic activity, which increased with the silica amount, in comparison with pure TiO2 nanoparticles. Due to better thermal stability, the photocatalytic activity of the silica-modified TiO2 sample held good photocatalytic activity even after calcined at 1273 K.     

Structure and photocatalytic properties of materials based on titanium dioxide and silver nanoparticles

Phase composition and structure of mesostructured materials, titanium dioxide and titanium dioxide modified with silver nanoparticles, have been studied by X-ray diffraction analysis. Introduction of Ag(I) ions into the initial composition and variation of the annealing temperature over the 500–950°C range allows controlling the anatase to rutile crystal phase ratio in the samples. The photocatalytic activity of TiO₂ and TiO₂/Ag samples has been demonstrated using the methyl orange degradation reaction. The catalytic properties of the materials have been found to depend on the anatase to rutile phase ratio and on the presence of silver nanoparticles.     

物理混合法制备分级混晶TiO2微纳米材料及其光催化性能

通过物理混合法可控合成了分级混晶TiO₂微纳米材料, 采用扫描电子显微镜(SEM)、 透射电子显微镜(TEM)、 X射线衍射仪(XRD)、 X射线光电子能谱仪(XPS)和固体紫外-可见分光光度计(UV-Vis)等对该微纳米材料进行了表征, 并评价了不同混晶比材料的光催化性能. 结果表明, 所得材料是由均匀负载金红石纳米颗粒的锐钛矿纳米片组装的三维分级结构. 其具有很高的光催化活性, 分级结构和混晶异相结的同时引入是提高材料光催化活性的关键.     

Crystallization and photovoltaic properties of titania-coated polystyrene hybrid microspheres and their photocatalytic activity

The hybrid microspheres with polystyrene core coated by titania nanoparticles were prepared by miniemulsion polymerization, and the as-prepared samples were characterized by SEM, XRD, TG-DTA, XPS, and SPS techniques. TiO2 nanoparticles experienced two processes of phase transition, i.e., amorphous to anatase and anatase to rutile at the calcining temperature range from 400 to 1000 degrees C. The phase transformation temperature of TiO2 hybrid microspheres from anatase to rutile was increased by about 300 degrees C due to the blocking function of calcined polymer remainder. SPS results present that the band-gap of hybrid microspheres is 3.2-3.4 eV, which is larger than that of pure TiO2. The maximum intensity of the SPS signal is about 3 times larger for the hybrid material as compared to the pure TiO2. In addition, the photocatalytic degradation rate of TiO2 hybrid microspheres was 15% faster than that of pure TiO2 in the experiment of the photocatalytic degradation of methyl orange.     

微波载银对纳米二氧化钛相变及光催化性能的增效作用

用微波法制备系列载Ag纳米TiO2,发现微波载Ag对纳米TiO2的相变和光催化活性具有增效作用。采用X-射线粉末衍射(XRD),透射电镜(TEM),X-射线光电子能谱仪(XPS),激光Raman光谱及漫反射光谱(DRS)方法对比研究纳米TiO2与载Ag纳米TiO2的性质。结果表明,所制得载Ag纳米TiO2是以锐钛矿为主相的混晶,平均粒径约为10 nm,负载Ag促进纳米TiO2中锐钛矿相转化金红石相相变,减小纳米晶尺寸,并使纳米TiO2光响应范围向可见光区移动 6 nm。在低浓度范围,微波法能均匀地将Ag负载于纳米TiO2表面,并以Ag0/Ag+的形式存在,抑制光生电子与光生空穴复合,大大地提高了纳米TiO2光催化活性。在近紫外-可见光照射下,载Ag量为0.05 mol %的纳米TiO2对罗丹明B的光催化降解效果最好。     

Synthesis,characterization and evaluation of nanocrystalline anatase titania for the degradation of dibutyl phosphate

Degradation of dibutyl phosphate (DBP) in aqueous solution was successfully demonstrated in this paper using nanoparticles of anatase titania. Nanocrystalline anatase titania employed for the degradation study was synthesized in house by solgel route under stirring mode using titanium ethoxide precursor. The catalyst was characterized using XRD, DRS, BET, TEM, TG–DTA and Raman spectroscopy to establish the catalytic activity and surface morphology. A cylindrical photoreactor was used for the photocatalytic experiments. 10 mg of nano anatase titania and 0.5 mL of 30 % H₂O₂ were used as catalysts for the degradation of 1,000 mL of 240 mg/L DBP. Ion chromatographic procedure was used for following the DBP degradation. More than 95 % of DBP degradation could be in less than 45 min and the kinetics of DBP was found to follow pseudo first order. It was demonstrated that the photocatalytic efficiency of the synthesized titania was better than P-25 titania.     

EPR investigation of TiO2 nanoparticles with temperature-dependent properties

An in situ electron paramagnetic resonance (EPR) study has been carried out for anatase (Hombikat UV100) and rutile TiO(2) nanoparticles at liquid helium (He) temperature (4.2 K) under UV irradiation. Rutile titania was synthesized by ultrasonic irradiation with titanium tetrachloride (TiCl(4)) as the precursor. XRD and Raman results evidence the crystallinity of titania phases. The nature of trapped electrons and holes has been investigated by EPR spectroscopy under air and vacuum conditions. Illumination of TiO(2) powder (anatase and rutile) at 4.2 K resulted in the detection of electrons being trapped at Ti(4+) sites within the bulk and holes trapped at lattice oxide ions at the surface. The stability of electron traps was very sensitive to temperature in both phases of TiO(2). The annealing kinetics of the EPR detected radicals has been studied from 4.2 K to ambient temperature and also for calcined titania particles from 523 to 1273 K.     

混合相二氧化钛石墨烯复合物的制备及光催化性能

采用水热法制备了一系列混合相二氧化钛-石墨烯(TrG)的复合物, 并考察了石墨烯的用量对降解污染物甲基蓝的影响. 采用X射线衍射(XRD), 傅里叶变换红外(FTIR)光谱, 高分辨透射电镜(HRTEM), 拉曼光谱,紫外-可见漫反射吸收光谱(UV-Vis DRS), X射线光电子能谱(XPS)和比表面积(BET)等测试手段对复合材料进行表征. 结果表明, 复合材料中TiO₂为棒状的混合相, 且均匀分散在石墨烯表面. 由于石墨烯良好的吸光性能,混合相中的异质结和复合物的良好光电子传递能力以及高比表面积, 复合材料具有较高的光催化活性. 所制备的TrG复合材料在紫外光下降解甲基蓝的催化活性均高于纯TiO₂, 且当氧化石墨烯负载量为0.8% (质量分数,w)时, 复合材料TrG具有较好的光催化效果.     

微乳法合成纳米SiO2/TiO2及其光催化性能

采用聚乙二醇辛基苯基醚(Triton X-100)/正己醇/环己烷/氨水微乳体系合成了纳米TiO2和SiO2/TiO2复合物,用X射线衍射、红外光谱和透射电镜对其结构进行了表征,并以甲基橙降解评价了其光催化性能,讨论了SiO2/TiO2摩尔比、晶相组成及粒径与光催化活性的关系.结果表明,SiO2/TiO2催化剂中形成了新的Ti-O-Si键和无定形SiO2;在纳米TiO2中复合SiO2能有效抑制锐钛矿向金红石的转变,增加锐钛矿的稳定性,并阻止TiO2晶粒的聚集生长.催化剂的光催化活性随金红石含量的增加而降低,加入适量SiO2能明显提高TiO2的光催化活性,其中摩尔比为1/7的SiO2/TiO2光催化活性最高.     

One-pot synthesis of highly crystalline mesoporous TiO2 nanoparticle assemblies with enhanced photocatalytic activity

We report an unprecedented formation of mesoporous titania via a surfactant-assisted aggregating assembly of TiO(2) nanoparticles. These mesostructures possess a highly crystalline anatase phase, large and accessible pore surface area, and exhibit superior photocatalytic performance.