Dynamic mechanical and dielectrical properties of poly(vinyl alcohol) and poly(vinyl alcohol)‐based nanocomposites

In this article we report on the investigation of the dynamics of poly(vinyl alcohol) (PVA) and PVA‐based composite films by means of dielectric spectroscopy and dynamic mechanical thermal analysis. Once the characterization of pure PVA was done, we studied the effect of a nanostructured magnetic filler (nanosized CoFe₂O₄ particles homogeneously dispersed within a sulfonated polystyrene matrix) on the dynamics of PVA. Our results suggest that the α‐relaxation process, corresponding to the glass transition of PVA, is affected by the filler. The glass‐transition temperature of PVA increases with filler content up to compositions of around 10 wt %, probably as a result of polymer–filler interactions that reduce the polymer chain mobility. For filler contents higher than 10 wt %, the glass‐transition temperature of PVA decreases as a result of the absorption of water that causes a plasticizing effect. The β‐ and γ‐relaxation processes of PVA are not affected by the filler as stated from both dynamic mechanical thermal analysis and dielectric spectroscopy. Nevertheless, both relaxation processes are greatly affected by the moisture content. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1968–1975, 2001     

Preparation and Properties of Poly（vinyl alcohol）/Chitosan Blend Bio-nanocomposites Reinforced by Cellulose Nanocrystals

The aim of this paper is to report the effect of the addition of cellulose nanocrystals（CNCs） on the mechanical, thermal and barrier properties of poly（vinyl alcohol）/chitosan（PVA/Cs） bio-nanocomposites films prepared through the solvent casting process. The characterizations of PVA/Cs/CNCs films were carried out in terms of X-ray diffraction（XRD）, transmission electron microscopy（TEM）, scanning electron microscopy（SEM）, thermogravimetric analysis（TGA and DTG）, oxygen transmission rate（OTR）, and tensile tests. TEM and SEM results showed that at low loading levels, CNCs were dispersed homogenously in the PVA/Cs matrix. The tensile strength and modulus in films increased from 55.1 MPa to 98.4 MPa and from 395 MPa to 690 MPa respectively, when CNCs content went from 0 wt% to 1.0 wt%. The thermal stability and oxygen barrier properties of PVA/Cs matrix were best enhanced at 1.0 wt% of CNCs loading. The enhanced properties attained by incorporating CNCs can be beneficial in various applications.     

Swelling behavior of a blend hydrogel made of poly(allylguanidino-co-allylamine) and poly(vinyl alcohol)

A hydrogel was prepared by mixing poly(allylguanidino-co-allylamine) hydrochloride (PAG) with poly(vinyl alcohol) (PVA) and repeatedly freezing and thawing the blend. The swelling behavior of the hydrogel was investigated as a function of the pH and ionic strength of the medium. In a salt-free aqueous medium, a size of the hydrogel was reduced below pH 3 and above pH 10, but the size was little affected in the pH range 3 ≈ 10. In a medium of constant ionic strength (μ = 0.1), the hydrogel's pH response was different: it was significantly reduced in size above pH 9, but the size was affected only moderately below pH 9. When the ionic strength of medium was varied at a fixed pH, the size change of the hydrogel was gradual. All these phenomena could be understood by observing that PAG displayed multiple protonation states due to pH and that the electrostatic interactions among the charges on the polymer backbone are shielded by the added electrolyte as the ionic strength of the medium is raised.     

Structure and properties of poly(vinyl chloride)/graphene nanocomposites

The goal of the paper was to investigate the influence of graphene (GN) on properties and structure of suspensive poly(vinyl chloride) (PVC). PVC/GN nanocomposites were obtained by the solvent evaporation method, and their structures were evaluated using optical microscopy, SEM, FT-IR, XRD and Raman spectroscopy methods. Thermal properties of the obtained materials were studied by TGA. Electrical properties and swelling behaviour were also determined.The microscopic observations confirm a uniform distribution of graphene in the PVC matrix. The investigations carried out indicated an effect of graphene on a decrease in resistivity to a value which enabled to include the PVC/GN nanocomposites into anti-static materials group. On the basis of swelling studies, it has been found that the PVC/GN nanocomposites have a higher chemical resistance against acetone while compared to pure poly(vinyl chloride). The properties of the obtained materials depend significantly on content and dispersion level of graphene in the PVC matrix. An impact of GN on the acceleration of the PVC degradation process was found.     

Characterization of poly(vinyl alcohol) during the emulsion polymerization of vinyl acetate using poly(vinyl alcohol) as emulsifier

During the emulsion polymerization of vinyl acetate (VAc) using poly(vinyl alcohol) (PVA) as stabilizer and potassium persulfate as initiator, the VAc reacts with PVA forming PVA-graft-PVAc. When the grafted polymer reaches a critical size it becomes water-insoluble and precipitates from the aqueous phase contributing to the formation of polymer particles. Since particle formation and therefore the properties of the final latex will depend on the degree of grafting, it is important to quantify and to characterize the grafted PVA. In this work, the quantitative separation and characterization of the grafted water-insoluble PVA was carried out by a two-step selective solubilization of the PVAc latex, first with acetonitrile to separate PVAc homopolymer, followed by water to separate the water-soluble PVA from the remaining acetonitrile-insoluble material. After the separation, the water-soluble and water-insoluble PVA were characterized by Fourier Transform Infrared (FTIR) spectroscopy and ¹H and ¹³C nuclear magnetic resonance (NMR) analyses, from which the details of the PVA-graft-PVAc structure were obtained. © 1996 John Wiley & Sons, Inc.     

Fully-biodegradable poly(3-hydroxybutyrate)/poly(vinyl alcohol) blend films with compositional gradient

Fully-biodegradable bacterial poly(3-hydroxybutyrate) (PHB)/chemosynthetic poly(vinyl alcohol) (PVA) blend films with compositional gradient from one surface to the other surface of the films were prepared by a dissolution-diffusion technique. Three kinds of PVA samples, high- and low-molecular weight atactic PVA and highly syndiotactic PVA (s-PVA), were used in order to investigate the effects of molecular weight and tactic structure on the generation of compositional gradient. The solution of PHB in 1,1,1,3,3,3-hexafluoro-2-propanol (HFIP), which is also a good solvent for PVA, was cast on the PVA film and then the solvent HFIP was evaporated. By selecting the optimum volume of solvent and the evaporation rate, the PHB/PVA blend film with compositional gradient was obtained. The formation of compositional gradient was confirmed by FT-IR microscopy and ATR-FT-IR analysis. The 50%/50% PHB/s-PVA blend film with a nearly ideal compositional gradient, that is, the composition of PHB (or PVA) in the film changing gradually from 100% at one surface to 0% at the other surface of the film was obtained by casting PHB/HFIP solution on to the s-PVA film. Positional dependence of the absorbance of C==O and OH stretching bands along the film thickness direction for the PHB/S-PVA cast films.     

Thermal decomposition behavior of poly(propylene carbonate) in poly(propylene carbonate)/poly(vinyl alcohol) blend

Journal of Thermal Analysis and Calorimetry - To provide guidance for the practical thermal processing and applications of poly(propylene carbonate)/poly(vinyl alcohol) (PPC/PVA) blend, an...     

Fabrication and characterization of transparent and biodegradable cellulose/poly (vinyl alcohol) blend films using an ionic liquid

Biodegradable blends were prepared from cellulose and poly (vinyl alcohol) (PVA) using the ionic liquid (IL) solvent, 1-butyl-3-methylimidazolium chloride. The blends were regenerated into films, fibers and rectangular blocks. The films showed optical transparency throughout the entire composition of the blends. The infrared spectroscopic experiments proved the existence of intermolecular hydrogen bonding interactions between the hydroxyl groups of cellulose and PVA. The miscibility between cellulose and PVA lead to increase in glass transition temperature (T _g) and of decrease in crystallinity of the blends. The T _g-composition data showed a negative deviation from Fox predictions, however fit well with BCKV model. The addition of PVA improved the tensile strength and elongation at break, considerably plasticizing cellulose. The blends can be degraded completely in soil. Moreover, the IL was completely recycled with high yield after the processing.     

Enzymatic degradation of some nanocomposites of poly(vinyl alcohol) with starch

A study of the enzymatic degradation of some montmorillonite-containing nanocomposites of poly(vinyl alcohol) with starch was based on the determinations of mass loss and the reducing sugars. The degraded residues have been examined by FT-IR spectroscopy and optical microscopy. It has been established that the nanoparticles hinder degradation, while the susceptibility to enzymatic degradation varies in the order: PVA/starch/nanocore > PVA/starch/Bentonite > PVA/starch/Peruvian clay.     

Pervaporation of alcohol-toluene mixtures through polymer blend membranes of poly(acrylic acid) and poly(vinyl alcohol)

Homogeneous membranes were prepared by blending poly(acrylic acid) with poly(vinyl alcohol). These blend membranes were evaluated for the selective separation of alcohols from toluene by pervaporation. The flux and selectivity of the membranes were determined both as a function of the blend composition and of the feed mixture composition. The results showed that a polymer blending method could be very useful to develop new membranes with improved permselectivity. The pervaporation properties could be optimized by adjusting the blend composition. All the blend membranes tested showed a decrease in flux with increasing poly(vinyl alcohol) content for both methanol—toluene and ethanol—toluene liquid mixtures. The alcohols permeated preferentially through all tested blend membranes, and the selectivity values increased with increasing poly(vinyl alcohol) content. The pervaporation characteristics of the blend membranes were also strongly influenced by the feed mixture composition. The fluxes increased exponentially with increasing alcohol concentration in the feed mixtures, whereas the selectivities decreased for both liquid mixtures.     

Preparation and properties of poly(vinyl alcohol)–vermiculite nanocomposites

A vermiculite (VMT) dispersion in water was blended with aqueous poly(vinyl alcohol) (PVA). The properties of the PVA–VMT nanocomposites greatly depended on the preparation procedure because of the chemical reactions and physical interactions involved. The samples were prepared in two steps to investigate the properties of the PVA–VMT nanocomposites. The VMT was first pretreated and delaminated with hydrochloric acid. The delaminated VMT was then added to the PVA solution with various mixing times. The structure and properties of the films were investigated. From X‐ray diffraction and transmission electron microscopy, the VMT layers were found to be well dispersed individually in the PVA–VMT blends. The effect of the VMT content on the thermal behavior of the PVA–VMT blends was also studied with differential scanning calorimetry. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 749–755, 2003     

Physical behavior of biodegradable alginate–poly(vinyl alcohol) blend films

Films of biodegradable blends based on sodium alginate for applications in agriculture, as films for the solarization of soils, were prepared and characterized in terms of the mechanical parameters and optical properties. The films analyzed in this study were transparent in the visible region and opaque in the infrared region. This ensured a micro greenhouse effect on the soil. One of the films was also characterized optically in the ultraviolet–visible–infrared region. The optical data were analyzed with a theoretical model, which was able to predict the temperature of the soil at different depths and at different times of the day. The susceptibility time of the film was compatible with its use in agriculture as a film for solarization. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1205–1213, 2005     

Miscibility and isothermal crystallization behavior of polyamide 6/poly(vinyl alcohol) blend

An investigation of miscibility and isothermal crystallization behavior of Polyamide 6 (PA6)/Poly(vinyl alcohol) (PVA) blends was conducted. Fourier transform infrared spectra (FTIR) analysis indicated that the interactions between the carbonyl groups of PA6 and hydroxyl groups of PVA increase as the weight ratios of PA6 to PVA of PA6/PVA specimens increase. This interaction between PA6 and PVA leads to their miscibility in the amorphous region and even some extent effects on their crystal phase, respectively. Further isothermal crystallization behavior of PA6/PVA indicate that the miscibility of PVA in PA6 leading difficulty in crystallization of PA6. Several kinetics equations are employed to describe the effects of PVA on the crystallization properties of PA6 in PA6/PVA blends in detail. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1360–1368, 2008     

Structure and compatibility of poly(vinyl alcohol)-silk fibroin (PVA/SA) blend films

The structure and compatibility of poly(vinyl alcohol)-silk fibroin (PVA/SF) blend films were analyzed by differential scanning calorimetry (DSC), thermomechanical (TMA) and thermogravimetric (TGA) analysis, x-ray diffractometry, and scanning (SEM) and transmission (TEM) electron microscopy. DSC curves of PVA/SF blend films showed a major endothermic peak at 220°C, along with a peak at 280°C. These endotherms were assigned to the thermal decomposition of the ordered PVA elements and to the thermal degradation of silk fibroin, respectively. The PVA/SF blends behaved in a manner intermediate to the pure components, as suggested by both contraction expansion and sample weight retention properties recorded by TMA and TGA measurements. The IR absorption spectra of the blends were identified as purely a composite of the absorption bands characteristic of both PVA and SF pure polymers. The X-ray diffraction patterns of PVA/SF blends showed overlapping spacing due to PVA and SF. A dispersed phase formed by spherical particles of 3–7 μm diameter was observed by SEM and TEM. All these findings suggest that PVA and SF are incompatible. © 1994 John Wiley & Sons, Inc.     

Silylation of poly(vinyl alcohol) with hexamethyldisilazane in liquid ammonia

Silylation of poly(vinyl alcohol) has been performed with hexamethyldisilazane in liquid ammonia in an autoclave. This novel procedure has the advantage that the educt, the reagent, and the product are soluble in ammonia, which works under homogeneous conditions. No salt like by-products are formed and no tedious purification of the product is necessary. The degree of silylation has been adjusted through the ratio of silylating agent to hydroxy groups. Random incorporation of trimethylsilyl groups was proven by the linear dependence of the glass transition temperature from the degree of silylation and the solubility of the partially silylated material. Quantitative investigation of the silylation reaction showed first-order kinetics for the initial and final stages of the reaction indicative of a reaction where k₁ > k₂ > k₃. © 1995 John Wiley & Sons, Inc.     

Flammability performance of poly(vinyl alcohol) nanocomposites with zirconium phosphate and layered silicates

Nanocomposites of poly(vinyl alcohol) with α-type zirconium phosphate (PVA/ZrP) and with layered silicates (montmorillonite and hectorite) were prepared by solution blending. Thermal properties and flame retardancy of the materials were characterized by thermogravimetric analysis and microscale combustion calorimetry. PVA/ZrP nanocomposite showed a faster charring process in temperature range between 200 and 350 °C but higher thermal stability and greater char yields above 350 °C and a different heat release rate feature, compared to clay-based samples. Observation of the micrographs of the chars from the nanocomposites present two distinct structures; one constituted by the stacked clay layers on the surface combined with clay-reinforced foams in the interior residue, and the other formed by carbon covered on the tightly curled ZrP nanoplatelets. The results indicated different flame retardant mechanisms of the two nanocomposites, which depend on the chemical/physical effects from the inherent properties of the nanofillers.     

Investigation of thermophysical properties of nanofluids containing poly(vinyl alcohol)-functionalized graphene

An experimental study was performed to evaluate the colloidal stability of water-based polyvinyl alcohol-functionalized few-layer graphene (water-based PVA–Gr) nanofluids and ethylene glycol-based polyvinyl alcohol-functionalized few-layer graphene (EG-based PVA–Gr) nanofluids. To this end, a liquid-phase exfoliation method was employed for mass production of graphene sheets (Gr). Then, a simple and novel method was introduced to do a direct functionalization of Gr with PVA. Surface functionality groups and morphology of PVA–Gr were analyzed by infrared spectroscopy, Raman spectroscopy and transmission electron microscopy. The results consistently confirmed the formation of PVA functionalities on Gr, while the structure of GNP has remained relatively intact. Then, UV–Vis was employed to investigate the stability of PVA–Gr in water and EG. The easily miscible PVA functionalities formed a great colloidal stability for Gr sheets. As a second criterion for having a promising coolant, thermophysical properties were measured experimentally. The thermal conductivity, density and viscosity of the nanofluids at concentrations of 0.025, 0.05 and 0.1 mass% were experimentally measured. As compared to the base fluid, the water-based PVA–Gr nanofluids show a significant enhancement at different conditions, like representing ~40% enhancement for 0.1 mass% at 40 °C. This simple and efficient procedure may play an important role for mass production of hydrophilic Gr, which be able to disperse in different solvents.     

Facilitated transport of CO2 through polyethylenimine/poly(vinyl alcohol) blend membrane

Polyethylenimine (PEI)/poly(vinyl alcohol) (PVA) blend membranes were prepared for the facilitated transport of CO₂. The polymeric carrier PEI was retained in the blend membrane by the entanglement with PVA chains. The CO₂ permeance decreased with an increase in CO₂ partial pressure in feed gas, whereas the N₂ permeance was nearly constant. This result clearly showed that only CO₂ was transported by the facilitated transport mechanism. The CO₂ and N₂ permeabilities increased monotonically with the PEI weight percent in the blend membrane, whereas the selectivity of CO₂ over N₂ showed a maximum. The selectivity increased remarkably with increasing heat-treatment temperature of the membrane. The highest selectivity obtained reached more than 230 when the CO₂ partial pressure was 0.065 atm. The prepared membrane was stable.