LC/MS determination of bisphenol A in river water using a surface-modified molecularly-imprinted polymer as an on-line pretreatment device

A new analytical method for the determination of bisphenol A (BPA) by LC/MS was developed and applied to environmental water samples. Quantitative MS detection of BPA was carried out in the negative mode. In order to preconcentrate the target compound yet prevent serious contamination of the water samples from the experimental environment, we employed column switching HPLC coupled with a pretreatment column of surface-modified molecularly-imprinted polymers. The recovery of BPA from a spiked environmental water sample was 102% and the repeatability of actual determinations of water samples containing 20 ng/L of BPA was 5.4% RSD. By modifying the surfaces of the molecularly-imprinted polymer particles packed in the pretreatment column, interference from the water samples was effectively removed, resulting in a significant increase in sensitivity and more reliable results. This method was successfully applied to the trace determination of BPA in environmental water samples using LC/MS.     

Improved detectability with a polymer-based trapping device in rapid HPLC analysis for ultra-low levels of bisphenol A (BPA) in environmental samples.

A new high-performance liquid chromatography (HPLC) method has been developed to detect ultra-low concentrations of bisphenol-A (BPA) (below 1 ng/L (ppt)) using column switching electrochemical detection (ECD). The results were superior to those obtained from manual pretreatment procedure with membrane stationary phase. BPA is inherently ubiquitous in the environment, including tools and solvents used for its analysis; to obtain meaningful results, therefore, the concentration of the overall BPA contamination must be below the detection limit for BPA using the analytical system. Therefore, purified water for preparing the standard BPA solution must be filtered with a hydrophobic membrane to suppress BPA background levels of contamination. In addition, we investigated methods for effectively preserving environmental water containing BPA. The addition of a small amount of ethylenediaminetetraacetic acid (EDTA) provided good recovery even after overnight storage. By employing these precautionary measures and procedures to reduce BPA contamination from the analytical procedure, we could accurately determine l(-10) ppt of BPA in environmental water samples using a column switching HPLC system.     

Preparation of uniformly sized molecularly imprinted polymers for phenolic compounds and their application to the assay of bisphenol A in river water.

Uniformly sized molecularly imprinted polymers, which can recognize bisphenol A (BPA), have been prepared by a multi-step swelling and polymerization method using BPA or a structurally related analogue of BPA [p-t-octylphenol (OP) or p-t-butylphenol (BP)] as the template molecule, 4-vinylpyridine as the functional monomer, and ethylene glycol dimethacrylate as the cross-linker. The BP-imprinted polymer showed higher molecular recognition ability for BPA than the OP-imprinted polymer. The BPA- and BP-imprinted polymers were applied for the assay of a trace amount of BPA in river water using column-switching HPLC with fluorescence detection: A BPA-imprinted polymer was used for removal of BPA from the pretreatment eluent as the trap column, and a BP-imprinted polymer was used for selective pretreatment and enrichment of BPA in river water as the pretreatment column. The calibration graph, constructed from peak area data plotted versus BPA concentration, was linear with a correlation coefficient of >0.999 in the concentration ranges of 25-1000 ppt. The limit of quantitation was 25 ppt with a 5-ml injection. The column-switching HPLC system was successfully applied for the assay of BPA in river water.     

Determination of bisphenol A with effective pretreatment medium using automated column-switching HPLC with fluorescence detection

A practical way for reducing contaminants, such as humic acids, and solving column-clogging problem in environmental water analysis with liquid chromatography is proposed. Detection interference by contamination is one of the most important issues of the environmental analyses. Moreover, due to the recent smaller diameter and fine particle size of an analytical column for HPLC system, a column-clogging problem is another practical difficulty as well. We found it possible to solve these problems by employing column-switching HPLC, which consists of a pretreatment column containing surface-modified polymer particles and flow changeover valves for cleaning the remaining matrices in the pretreatment column prior to analysis. This method was successfully applied to actual HPLC-fluorescence detection of bisphenol A. Limit of detection (LOD) in real sample was <0.7 ng/L. Repeatability was around 1.4% and recovery was around 97% or more. A particular pressure increase was not observed in 150 repeated analyses of real river water samples.     

Investigation of diazo‐derivatization of bisphenol A and its applicability for quantitation in food safety inspections using high‐performance liquid chromatography

Bisphenol A (BPA) is a common additive in food packaging materials, and many methods have been discovered to limit BPA for the sake of food safety. This study aims to find a more sensitive quantification method for BPA. It was determined that a diazo derivative of BPA could be obtained when reacted with a stable and inexpensive reagent, p‐methylaniline, exhibiting an increased response in the ultraviolet spectrum than that of nonreacted BPA. Based on this discovery, an accurate method of BPA quantitation was established using a precolumn derivatization HPLC method. The results of this study showed the low limit of detection and the limit of quantitation for BPA were 3.6 and 10.9 pg/mL on‐column, respectively. This method is proven to have much higher sensitivity and a lower limit of detection than direct HPLC determination methods. This method is robust, easily handled, sensitive and cost‐effective for the quantitation of BPA. In addition, the broad application of this method to determine BPA content in plastic bottled drinking water, distilled water, tap water, milk, Sprite and grape juice was demonstrated in this paper.     

Continuous solid-phase extraction and preconcentration of bisphenol A in aqueous samples using molecularly imprinted columns

A bisphenol A (BPA) molecularly imprinted polymer, the composition of which was optimised using a chemometric approach, has been applied to the selective preconcentration of the template from aqueous samples. The selectivity of the polymer toward BPA and related compounds was evaluated chromatographically. The BPA-imprinted polymer was packed in a column and used for continuous on-column solid-phase extraction (MISPE) of aqueous samples followed by subsequent analysis by HPLC with fluorescence detection of the eluted fractions. The composition of the washing solvent applied in the MISPE procedure was optimised to favour the specific interactions of the MIP with BPA and to remove the non-selectively bound matrix components. The MISPE method has proven to be effective for selective preconcentration of BPA in aqueous samples (recoveries >84% obtained in the eluate for 10–100 mL sample volumes) enabling detection and quantification limits of 1.0 and 3.3 ng mL^–1, respectively (based on 25 mL sample size). Analytical recoveries were between 92 and 101% for river water samples spiked with known amounts of BPA (30, 60, and 80 ng mL^–1); relative standard deviations (RSD) were lower than 5.0%.     

Bioanalysis of the investigational anti-tumour drug 5,10-dideaza-5,6,7,8-tetrahydrofolic acid by high-performance liquid chromatography with ultraviolet detection.

A high-performance liquid chromatographic (HPLC) method with ultraviolet detection at 278 nm is presented for the determination of 5,10-dideaza-5,6,7,8-tetrahydrofolic acid in plasma. Sample pretreatment was achieved by using cation-exchange solid-phase extraction columns with methotrexate as internal standard. Chromatographic separation was based on ion-pair HPLC with 1-octanesulphonic acid as the ion-pairing compound. The detection limit was 10 ng/ml using an 500-microliters sample volume. The assay was linear from the detection limit up to 5000 ng/ml with good reproducibility. The applicability of the assay was demonstrated in a study in the rat.     

Development and validation of an LC‐MS/MS method for simultaneous quantitative analysis of free and conjugated bisphenol A in human urine

Bisphenol A (BPA) is an environmental endocrine‐disrupting chemicals that is widely used in common consumer products. There is an increasing concern regarding human exposure to BPA owing to the potential adverse effects associated with its estrogenic activity. For assessing environmental exposure to BPA, it is essential to have a sensitive, accurate and selective analytical method, especially one that can detect low BPA levels in complex sample matrices. In this study, we developed and validated an accurate, sensitive, and robust liquid chromatography–tandem mass spectrometry method for simultaneous quantification of free BPA and BPA β‐d ‐glucuronide (BPA‐gluc) concentrations in human urine with only a single injection. Calibration curves were linear over a concentration range of 1–100 ng/mL for BPA and 10–1000 ng/mL for BPA‐gluc. The levels of the analytes were determined quantitatively with HPLC/ESI‐MS/MS by using negative electrospray ionization in the select ion monitoring mode and a pentaflouraphenyl propyl column. The validated method was applied to the analysis of spot urine specimens collected from randomly selected healthy human subjects. Copyright © 2013 John Wiley & Sons, Ltd.     

高效液相色谱法测定环境水中超痕量双酚A

合成单分散双酚A(BPA)分子印迹微球并以其为高效液相色谱柱填充材料,建立了一种大体积直接进样HPLC法测定环境水中超痕量BPA的方法。方法的检出限(LOD)和测定限(LOQ)分别为0.03nmol/L和0.1nmol/L;在0.1~100nmol/L范围内具有良好的线性(r2=0.9983)。本方法用于表层湖水中BPA的检测,实际样品的加标回收率在99%~101.4%间;相对标准偏差(RSD%)低于8.1%(n=5)。     

Shielded molecularly imprinted polymers prepared with a selective surface modification

Uniformly sized, molecularly imprinted polymers (MIPs) of bisphenol A (BPA), one of many potential endocrine disruptors, were prepared by selective surface modification and immobilized at intervals of functional monomers with 4,4′‐methylenebisphenol as a pseudotemplate. MIPs for BPA were prepared with 4‐vinyl pyridine immobilized at the most effective interval and with ethylene glycol dimethacrylate monomer as a functional crosslinker. The prepared MIPs were surface‐modified with both polar and ionic monomers with different modification methods and then evaluated to reveal their selectivity and retention characteristics. Some of the modified MIPs showed significant selectivity for BPA retention when they were used as high‐performance liquid chromatography (HPLC) stationary phases, in comparison with ordinary MIPs. This effect of molecular imprinting was retained even after the surface modification of MIPs. The MIPs employed as pretreatment media for a column‐switching HPLC system provided a detection limit as low as 1 ng/L (ppt) by electrochemical detection. Actual samples, including Suwannee River natural organic matter (NOM), were analyzed for BPA, and BPA was quantitatively detected in NOM even with the combination with widely used UV detection because of the effective removal of interference afforded by an effective surface modification of the MIPs. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2048–2060, 2005     

三相中空纤维膜液相微萃取-高效液相色谱法测定水中痕量双酚A

建立了三相中空纤维膜液相微萃取-高效液相色谱(HF-LPME-HPLC)方法,用于分析测定水中痕量双酚A的含量.设计了三相中空纤维膜液相微萃取系统,优化的HP-LPME最佳萃取条件为:萃取剂为正辛醇,接受相NaOH浓度为0.09 mol/L,样品溶液pH=4.0,NaC1加入量为30 g/L,搅拌速度为900 r/min,萃取时间为60 min.萃取后取20 μL接受相进行色谱分析.在最佳萃取条件下,方法的线性范围为0.5～200 μg/L(r＞ 0.999),检出限(信噪比为3)为0.2 μg/L;富集因子为241;方法RSD＜3.2％ (n=3).在实际环境水样中添加5,20和50μg/L的双酚A标准物质,加标平均回收率为92.8％～101.9％.表明本方法可用于水中痕量双酚A的快速准确测定.     

分子印迹聚合物为涂层的吸附萃取搅拌棒在环境水样双酚A含量测定中的应用

以双酚A(BPA)为单体,利用整体材料“原位”聚合技术制备以分子印迹聚合物为涂层的吸附萃取搅拌棒(MIP-SBSE),然后与高效液相色谱(HPLC)-二极管阵列检测器联用,探讨其对环境水样BPA的选择萃取性能。优化萃取过程中吸附和解吸时间、解吸液种类以及基底pH值和离子强度对目标化合物的选择吸附性能。在最佳条件下,MIP-SBSE可对模板分子进行有效的选择吸附,线性范围为1.0～200 μg/L,检出限(S/N=3)和定量限(S/N=10)分别为0.28μg/L和0.94 μg/L。在实际水样分析中,具有良好的加标回收率,其值为96.0%～108.7%。研究结果表明,所建立的方法具有简便、灵敏和环境友好等特点。     

Highly selective stir bar coated with dummy molecularly imprinted polymers for trace analysis of bisphenol A in milk

A water compatible molecularly imprinted polymers (MIPs) coated stir bar for bisphenol A(BPA) was prepared with 3,3',5,5'-tetrabromobisphenol A as the dummy template molecule in this study. The dummy molecularly imprinted polymers coated stir bar (DMIPs-SB) showed better selectivity than the bars coated with polydimethylsiloxane or non-imprinted polymers when used to extract BPA and its three analogues. The saturated adsorption amount of the DMIPs coating was 3.0 times over that of the non-imprinted polymers coating. To achieve the optimum extraction performance, several parameters, including extraction and desorption time, pH value, adsorption temperature and stirring speed were investigated. The high-performance liquid chromatography combined with the DMIPs-SB was employed in the analysis of BPA in aqueous solution. The linear range of BPA concentration in aqueous medium was 0.0228-2.28 ng/mL with correlation coefficient of 0.9994 and the detection limit was about 6.84 × 10(-3) ng/mL based on three times ratio of signal to noise. This method was directly applied to the determination of trace BPA in milk with satisfactory results.     

QbD-driven development and validation of HPLC method for determination of Bisphenol A and Bis-sulphone in environmental samples

ABSTRACT

A large number of hazardous chemicals have entered the environment due to the rapid growth of urbanisation and industrial development and are exerting harmful effects on wildlife as well as on human health. Plastic materials are one of the most leading causes for this contamination which are widely used in daily activities of human beings, i.e. disposal purpose, food packaging, bottles, containers, cups, grocery bags, etc. These materials contain Bisphenol A (BPA) and Bis-sulphone (BIS) which have been recognised as potential endocrine disruptors. In the present study, a selective and reliable high-performance liquid chromatography (HPLC) based method was developed with the mobile phase of 10 mM ammonium acetate buffer-acetonitrile (58:42 v/v, pH: 5) using quality by design (QbD) approach and the method was validated for the simultaneous assessment of BPA and BIS. The method was observed with a good linearity range of 50–500 ng/mL with an r² value of 0.998 and 0.999 for BPA and BIS, respectively. The developed and validated method was applied for the estimation of endocrine-disrupting chemicals in sewage water and soil samples. The results showed a considerable amount of BPA and BIS in the samples. This preliminary data explored the presence of BPA and BIS in these environmental samples that give the primary awareness of the effluence of BPA and BIS in the environment.     

Preparation of functionalized magnetic nanoparticulate sorbents for rapid extraction of biphenolic pollutants from environmental samples

A new solid-phase extraction coupled with magnetic carrier technology was developed for extraction of bisphenol A (BPA) and diethylstilbestrol (DES) from water samples. The SPE sorbents, functionalized magnetic nanoparticles (Fe₃O₄@SiO₂/β-CD, core/shell), were synthesized in a two-stage system. The material was characterized by Fourier transform infrared spectroscopy, transmission electron microscopy, and a vibrating sample magnetometer. SPE extraction parameters, such as volume and pH of sample, adsorption time, and desorption conditions were optimized. Under selected conditions: 250 mL of water sample, 0.1 g of sorbents and elution with methanol (3 mL with 1% acetic acid), the extraction was completed in 25 min. SPE followed by HPLC was employed to determine BPA and DES in environmental samples. The developed method provided spiked recoveries of 80–105%, relative standard deviations of less than 7%, and LOD of BPA (20.0 ng/L) and DES (23.0 ng/L), respectively. The proposed method offered easy preparation of sorbents, rapid analysis, high enrichment yields, and reliable quantitative assay.     

Determination of polycyclic aromatic hydrocarbons in water by solid-phase microextraction and liquid chromatography.

This study describes the determination of polycyclic aromatic hydrocarbons (PAHs) in water using high-performance liquid chromatography (HPLC) coupled with fluorescence detection (FLD). Because individual PAHs are generally present in water only at trace levels, a sensitive and accurate determination technique is essential. The separation and detection of five PAHs were run completely within 25 min by the HPLC/FLD system with an analytical C18 column, a fluorescence detection, and acetonitrile-water gradient elution. Calibration graphs were linear with very good correlation coefficients (r > 0.9998), and the detection limits were in the range of 2-6 ng/l for five PAHs. Solid phase microextraction (SPME) was performed for sample pretreatment prior to HPLC-FLD determination, and the governing parameters were investigated. Compared to conventional methods, SPME has high recovery, saves considerable time, and reduces solvents waste. The extraction efficiencies of five PAHs were above 88% and the extraction times were 35 min in one pretreatment procedure. One particular discovery is that 1.5 M sodium monochloroactate (ClCH2COONa) can improve the extraction yield of PAH compounds more than other inorganic salts. The SPME-HPLC-FLD technique provides a relatively simple, convenient, practical procedure, which was here successfully applied to determine five PAHs in water from authentic water samples.     

Determination of some selected polycyclic aromatic hydrocarbons in environmental samples by high-performance liquid chromatography with fluorescence detection

Summary Analytical methods for the determination in environmental samples, of some selected Polycyclic Aromatic Hydrocarbons (PAH's), which are included on the EPA Priority Pollutant list, have been developed and evaluated. The methodology involves the extraction of PAH's from water samples by solvent extraction with dichloromethane. Solid samples were ultrasonically extracted with acetone/hexane and the extract was cleaned up on a silica gel/alumina column. The concentrated and cleaned up extracts were analysed by HPLC on a polymeric C₁₈ column using a gradient of acetonitrile/water as the mobile phase and fluorescence detection. Typical detection limits lie in the range of 1–30 ng ml^–1 of the analytes, but after sample pretreatment detection limits of 10–300 ng l^–1 were obtained. The extraction, clean-up and HPLC methodology was applied to the determination of selected PAH's in coal washings samples and the method was validated by the quantification of PAH's in a natural contaminated and a spiked sediment.     

Exploration of coordination polymer as sorbent for flow injection solid-phase extraction on-line coupled with high-performance liquid chromatography for determination of polycyclic aromatic hydrocarbons in environmental materials

The copper(II) isonicotinate (Cu(4-C5H4N-COO)2(H2O)4) coordination polymer was prepared, characterized and explored as sorbent for flow injection solid-phase extraction on-line coupled with high-performance liquid chromatography (HPLC) for determination of trace polycyclic aromatic hydrocarbons (PAHs) in environmental matrices. Naphthalene, phenanthrene, anthracene, fluoranthene, benzo(b)fluoranthene, benzo(k)fluoranthene, benzo(a)pyrene and benzo(ghi)perylene with various shape, size and hydrophobicity were used as model analytes. The porosity of the coordination polymer allows these guest PAHs molecules to diffuse into the buck structure, and the shape and size of the pores lead to shape- and size-selectivity over the guests. The precolumn packed with the coordination polymer was shown to be promising for solid-phase extraction of PAHs in environmental samples with subsequent HPLC separation and UV detection. With extraction of 50 ml of sample solution, the enhancement factors for the PAHs studied ranged from 200 to 2337, depending on the shape, size and hydrophobic property of the PAHs. The detection limits (S/N = 3) of 2-14 ng l(-1) and the sample throughput of 3 samples h(-1) were obtained. The developed method was applied to the determination of trace PAHs in a certified reference material (coal fly ash) and local water samples.     

Development of a molecularly imprinted polymer for selective extraction of bisphenol A in water samples

A cross‐linked methacrylate molecularly imprinted polymer (poly‐4‐vinylpyridine‐co‐trimethylolpropane‐trimethacrylate) selective for bisphenol A (BPA) was synthesized, using a fluorinated BPA derivative (4,4′‐(hexafluoroisopropylidene)‐diphenol) as a mimic template, and applied to the analysis of real‐world samples of process and potable waters. The molecularly imprinted polymer also showed a high affinity and selectivity for 17‐β‐estradiol and ethynylestradiol. A method to analyze BPA, 17‐β‐estradiol, and ethynylestradiol at ultratrace levels was thus developed from a screening procedure to monitor endocrine‐disrupting chemicals in water samples. The method consists of the BPA‐selective cleanup by molecularly imprinted SPE using cartridges packed with the polymer developed, its recovery by stir bar sorptive extraction after ad hoc derivatization to obtain the corresponding BPA‐acetate, and its analysis by GC‐time window‐SIM‐MS after online thermal desorption. The method showed good linearity in the working range (R²=0.9969), high repeatability (RSD% <10.1), recoveries always above 90%, and very low LOD (10 pg/L) and LOQ (1 ng/L) and can easily be extended to the determination of 17‐β‐estradiol and ethynylestradiol ultratraces. The method's effectiveness was evaluated by analyzing the real‐world water samples; it enabled preconcentration and detection of BPA at ultratrace levels.     

Measurement of bisphenol A and bisphenol B levels in human blood sera from healthy and endometriotic women

A sensitive HPLC method with fluorescence detection was developed for the determination of bisphenol A (BPA) and bisphenol B (BPB) in human blood serum. The detection limits of the method were 0.18 and 0.20 ng/mL for BPA and BPB, respectively. A single‐step liquid–liquid extraction was used for the pre‐treatment of serum samples. The recoveries of BPA and BPB spiked to sera were 85.6 and 87.7%, respectively. The analyses of sera from both healthy and endometriotic women emphasized the absence of bisphenols in all the control cases (11 women), whereas BPA was found in 30 sera (51.7%) and BPB was found in 16 sera (27.6%) in the group of 58 patients with endometriosis; in nine of such sera BPA and BPB were present simultaneously. Only relatively to the sera quantitated, BPA concentrations ranged from 0.79 to 7.12 ng/mL (mean concentration 2.91 ± 1.74 ng/mL), whereas BPB concentrations ranged from 0.88 to 11.94 ng/mL (mean concentration 5.15 ± 4.16 ng/mL). Therefore, the presence of at least one of the two bisphenols was verified in a percentage as high as 63.8% in the sera from endometriotic women, suggesting the existence of a relationship between endometriosis and BPA and/or BPB exposure. Indeed, it is well known that bisphenols can work as xenoestrogens, owing to their structural similarity to natural and synthetic estrogens (e.g. estradiol and dietilstilbestrol). However, further studies are necessary to confirm this hypothesis and to assess the actual dose at which exposures to bisphenols are able to increase the sensitivity of the endometriotic cells to estradiol. Copyright © 2009 John Wiley & Sons, Ltd.