柚皮苷的热稳定性及其热分析动力学研究

用TG-DTG/DTA方法研究了柚皮苷的热降解过程及热分析动力学. 热重分析结果表明该物质的失重过程分两步进行. 第一步为结晶水脱出, 其温度范围为343～545 K, 第二步为其分子骨架大规模降解, 其温度范围在545～857 K. 差热分析结果表明, 该物质的熔化温度为439.2 K. 使用Friedman和Ozawa-Flynn-Wall两种方法分别计算出该物质降解过程的活化能. 采用多步线性回归方法, 并参考常用的15种热解机理函数, 确定了柚皮苷热解过程最佳动力学模型为Fn-F2-F1.     

丹酚酸B的热稳定性及其热分解动力学研究

用TG-DTG 方法研究了丹参的有效成分丹酚酸B 的热降解过程. 热重分析结果表明该物质的失重过程分两步进行. 笫一步为脱去吸附水, 其温度范围为305～373 K, 第二步为丹酚酸B 分子骨架大规模降解, 其温度范围在413～864 K. 用Friedman 和Ozawa-Flynn-Wall 两种方法分别计算出该药物降解过程中的三个阶段的活化能, 采用多步线性回归方法, 并参考常用的15 种热解机理函数, 确定了丹酚酸B 热降解过程最佳动力学模型为Fn-F2-F1.     

Re-examination of the Kinetics of the Thermal Dehydroxylation of Goethite

The kinetics of thermal dehydroxylation of aluminuous goethites [1] synthesised from a ferrous salt has been re-examined using the general reaction order kinetic law. The utilised data processing was based on the procedures employed by dissolution kinetics. Recalculation of the activation energies E_A of the dehydroxylation yielded the values 130, 132, 128, and 123 kJ mol⁻¹ for pure goethite, goethite with 10, 20, and 30 mol% Al substitution, respectively. The values of E_A are in a good agreement with those given for goethite in literature. The E_A values are linearly related with the chemically bound excess H₂O/OH⁻ in the crystal lattice that is apparently influenced by Al substitution. This revised version was published online in August 2006 with corrections to the Cover Date.     

芳基乙炔聚合物热分解动力学研究

利用ＴＧ－ＤＴＧ方法研究了聚（ｐ－ＤＥＢ）在氮气和空气气氛中的热分解过程和动力学。实验发现,在氮气中其热分解反应为一步反应,热分解速率较低,热分解４温度随升温速率β的增加而线性增加,在７３０℃下残碳率高达８７％;而在空气中其热分解反应则由多步组成,热分解速率较快,热分解温度低,升温速率对热分解温度影响不大,在６００℃下聚合物已完全分解。在氦气和空气中聚合物的热分解反应均为一级速率对热分解温度不大,     

金属卟啉的热稳定性及热分解动力学研究

热重分析;金属卟啉的热稳定性及热分解动力学研究     

热分析动力学数据处理方法的研究进展

综述了最近几年来用热分析法研究固相反应动力学的数据处理方法的新进展,指出了现有方法的成功与局限性,介绍了几种新的动力学处理方法及一种新的热分析技术。     

Thermal analyses of synthetic high basicity sinters

The paper presents studies on synthetic sinters of given basicities (CaO/SiO₂ 1.7–2.1). These multicomponent systems include not only doped iron oxides but calcium ferrites and numerous silicate phases as well. Investigatons were carried out by complex research methods, first of all by thermal analysis. Reduction processes of the sinters were observed by the methods of polythermal analysis in CO/CO₂ atmosphere. The effect of mineral composition on physico-chemical properties of the sinters has been determined.     

Kinetics of Thermal Decomposition of Dolomite

The thermal decomposition reactions of calcitic dolomite were investigated. Simultaneous TG/DTG/DTA were applied under non-isothermal conditions. From the recorded curves, the activation energies, pre-exponential factors and thermodynamic parameters of activation were calculated for the two thermal decomposition steps. This revised version was published online in August 2006 with corrections to the Cover Date.     

丙烯酸化环状磷腈/环氧丙烯酸酯光固化体系热降解动力学研究

以TGA为手段, 进行了丙烯酸化环状磷腈/环氧丙烯酸酯光固化体系热降解动力学的研究, 同时与加入粉末状环状磷腈混合体系进行了对照. 采用Kissinger, Flynn-Wall-Ozawa和Friedman三种方法计算了固化膜降解反应活化能, 证明了磷腈结构的引入, 使得体系在高温阶段的活化能有所提高, 表明降解变得困难, 热稳定性得到提高. 而反应型丙烯酸化环状磷腈相对粉末状环状磷腈混合体系具有更高的降解活化能.     

丙硫异烟胺的热稳定性及其热分解动力学

通过热重法研究了抗结核药物丙硫异烟胺的热稳定性, 计算了该药物的动力学参数并建立了热分解动力学方程. 用Kissinger和Ozawa-Flynn-Wall两种方法计算该药物热分解过程的活化能Ea=54.65 kJ·mol-1. 用Malek法推断该药物的动力学机理函数及指前因子A, 其结果分别为f(α)=α0.391(1-α)0.145, lnA=13.12. 此外, 用差热法测定该物质的熔点、摩尔熔化焓和摩尔熔化熵, 分别是414.09 K、23.21 kJ·mol-1和56.06 J·mol-1·K-1.     

Kinetics of the Formation of Goethite in the Presence of Sulfates and Chlorides of Monovalent Cations

The synthesis of goethite by oxidation of Fe²⁺in presence of metallic iron was undertaken in an aqueous medium containing indifferent salts such as Na₂SO₄, (NH₄)₂SO₄, NaCl, and NH₄Cl. Temperature and bubbling air rate were maintained, respectively, at 70°C and 1 L/min. The influence of anions and cations on the kinetics of each step of the process has been followed distinctly, the iron dissolution rate has been determined by the variation of the medium acidity, and the precipitation of goethite has been determined by gravimetric measurements. With respect to Cl⁻, the SO₄²⁻anion decreases the rate of the two reactions. NH₄⁺acts as an inhibitor when it is present at low concentrations and as an accelerator for higher concentrations; the limit corresponding to the change of NH₄⁺behavior depends on the nature of the counter ion. The reaction product is composed of pure goethite in the presence of sulfate salts, whereas a mixture of goethite and lepidocrocite, respectively, 60–70 and 40–30%, was observed in the presence of chloride salts.     

二水草酸亚铁热分解行为及脱水反应动力学研究

The thermal behavior of ferrous oxalate dihydrate (FeC₂O₄·2H₂O) was studied by thermogravimetry and differential thermal analysis (TGA and DTA). Three steps could be deduced for the decomposition from the TG,DTG and DTA curves obtained. One of the steps was the dehydration, the mass loss was 20.1%(the found value was in good agreement with the calculated value). Mathematical analysis with the integral and differential methods showed that the kinetics of dehydration of FeC₂O₄·2H₂O could be explained by F1 mechanism in nitrogen atmosphere. The kinetic equation of dehydration of FeC₂O₄·2H₂O could be expressed as: dα/dt=6.25×10¹⁹[exp(-170.27×10³/RT)](1-α)     

热分析法研究五倍子醛的热稳定性及其分解动力学

采用热重法,以氮气为保护气,分别在5、10、15、20℃/min的升温速率下,测得五倍子醛的热重-微分热重(TG-DTG)曲线,并在10℃/min的升温速率下测得样品的差示扫描量热(DSC)曲线。结合热失重数据和五倍子醛结构对其分解机理进行推断和验证,并运用双外推法对五倍子醛的热解动力学进行分析,求得原始状态和热平衡态下的动力学参数。研究结果表明,五倍子醛晶体在升温过程中先经历了非结合水和结合水的受热挥发阶段,然后在163℃之后发生热分解,分子中醛基断裂失去1分子的CO;随着升温速率的升高,五倍子醛的分解反应向高温区域移动,最大失重速率依次减小;热解活化能Eα为286.21 kJ/mol,指前因子lnA为70.21,热解机理函数g(α)=[-ln(1-α)]2/3,反应级数n=2/3;热解活化能随转化率的增加逐渐减小;经动力学参数推断,在室温(25℃)下,五倍子醛的贮存期为4～5年。     

氟碳铈矿热分解动力学研究

采用Harcourt-Esson方法对不同来源的氟碳铈矿晶体热分解动力学进行了系统研究，得到的反应机制方程用普适积分法进一步验证，结果显示微山矿热分解为一级反应，不同品位的冕宁、非洲、芒廷帕斯氟碳铈矿热分解反应都是按照三维扩散机制进行的。     

预氧化聚铝碳硅烷纤维的热分解动力学及其机理

利用热重分析仪(TGA)对预氧化聚铝碳硅烷(PACS)纤维进行了热动力学研究, 用改良的Coats-Redfern法计算了动力学参数, 用Doyle法计算了理论失重值, 并根据FT-IR, XRD和SEM对其热分解的机理进行了分析. 结果表明, 在热分解反应的主要阶段, 预氧化纤维的反应活化能低于PACS纤维, 氧的引入有利于纤维的热分解; 快速升温有利于预氧化PACS纤维的热分解. 在初始分解阶段, 主要为低分子量的PACS和H₂O的逸出, 同时≡Si—H键之间以及≡Si—H与≡Si—CH₃键发生了脱氢、脱CH₄反应, 从而导致交联程度的增加; 随热分解温度进一步的提高, 分子的有机侧基急剧热解, 分解产物从有机物转变为存在部分微晶的无机结构; 热分解温度继续提高, 纤维结构进一步完善, 1300 ℃左右, β-SiC晶粒大小约为2～4 nm左右, 纤维具有较好的性能.     

水合硼酸锶的制备及脱水热分解动力学

以氯化锶和硼酸氢铵为原料,采用液相沉淀法制备了片状水合硼酸锶（SrB6O10•5H2O）粉体,并用XRD、FT-IR及SEM进行了表征。利用热重分析法对片状纳米硼酸锶粉体的脱水热分解动力学进行了研究,分别采用 Coats- Redfern 方程和 Flynn-Wall-Ozawa（FWO）法对热重分析数据进行了处理和拟合,初步确定了水合硼酸锶的四步脱水过程及相应的热分解反应机理,得到各步反应的表观活化能和指前因子。     

聚氨酯弹性体的热分解动力学研究

聚氨酯弹性体的热分解动力学研究;聚醚型聚氨酯;聚酯型聚氨酯;热分解;动力学;模型拟合法     

Thermal Decomposition Kinetics of Triethylene Glycol Dinitrate

Introduction Triethylene glycol dinitrate (TEGDN) is a novel en-ergetic material containing two groups of NO2, which can be used as an energetic plasticizer ingredient in propellants because of its excellent proformance.1 It exhibits lower impact sensitivity, better thermostability, weaker poisonousness and volatility, and stronger effec-tiveness of plasticizing cellulose nitrate than nitroglyc-erine (NG). As a new plasticizer TEGDN has good ap-plication prospects in the near future. The…     

超细AgO粉末:制备及热分解非等温动力学

采用化学沉淀法,以臭氧为氧化剂制备了超细AgO粉末,并用XRD、XPS、SEM和粒度分析仪对制备的粉末进行了表征,借助热重分析法(TG)和线性升温理论对超细AgO粉末的热分解过程和非等温热分解动力学机理进行了研究。结果表明,制备的AgO属于单斜晶系,形貌为片状,其粒径分布在45～551nm之间,大部分在200nm左右;AgO的热分解分两步,158℃开始分解,放出氧气形成Ag2O,413℃进一步分解形成Ag;其热分解反应服从核生成和核成长为控制步骤的A2机理,热分解表观活化能为90.26kJ·mol-1,反应频率因子为1.64×108s-1。     

Kinetics of thermal decomposition of nickel sulfate hexahydrate

The paper describes the kinetics of all the recorded steps of thermal decomposition of nickel sulfate hexahydrate in air. The thermal decomposition of the salt in air led to NiO at about 1060 K. The kinetic parameters, the activation energyE and the preexponential factorA, and the thermodynamic parameters, the entropy, enthalpy and free energy of activation were evaluated for the dehydration and decomposition reactions. Tentative reaction mechanisms are suggested for each step of the thermal decomposition.