利用光束的轨道角动量实现高密度数据存储的机理研究

光束的轨道角动量本征态可以构建高维Hilbert空间，将之应用于数据存储中，可以实现比传统方法更高的数据存储密度.提出了一种用光束轨道角动量实现高密度数据存储的方法，对存储区域进行相位编码，通过探测透射光束轨道角动量谱(螺旋谱)的特征来区分由相位编码形成的不同数据态.四台阶结构相位编码可以实现57个不同的数据态，有望将数据密度提高为传统方法的近6倍. 关键词： 光束轨道角动量 光学存储 高密度存储     

Numerical Analysis of Nano-Aperture Light Source for High-Density Optical Data Storage

Two unconventional nano-aperture light sources, an L-shaped nano-aperture source and a 3D nano-aperture source for high-density optical data storage, are numerically investigated. With incidence of a Gaussian beam, the spot size of the Poynting vector coupled into the recording medium is 130 × 175 nm^2 for the L-aperture and 120 × 135 nm^2 for the 3D nano-aperture. The quantitative analyses indicate that the unconventional nanoaperture sources can provide enough power density to record marks in the commercial recording medium. It is feasible to use a laser diode with a nano-aperture as an active nanometer light source for high-density optical data storage.     

Multilevel phase and amplitude modulation method for holographic memories with programmable phase modulator

The utilization of spatial quadrature amplitude modulation (SQAM) signals with amplitude and phase modulation is a simple method used to improve storage capacity in a holographic data storage system. We propose a multilevel phase and amplitude modulation method for holographic memories with a programmable phase modulator (PPM). In this method, holographic page data is recorded by a two-step exposure process for different phase-modulated data. There is no need to adjust the positions of spatial light modulators (SLM) with high accuracy because we use only one spatial modulator. We estimate the quality of 16 SQAM signals produced by our technique.     

基于LiNbO3晶体的透射式共光轴体全息存储技术

共光轴体全息存储是体全息存储技术实用化的一个发展方向。为了选择合适的参数以搭建基于晶体的透射式共光轴体全息存储系统,对该系统的存储容量、串扰特性和晶体在共光轴存储结构中的存储特性等进行了研究。从理论上分析了共光轴体全息存储系统的存储密度、物镜的参数、空间光调制器的像素尺寸、有效像素数目和移位复用间隔等之间的关系,给出了点扩展函数表达式的物理解释,并根据点扩展函数分析了系统的串扰特性,优化了存储偏振光方向以使晶体表现出最大的动态范围。根据分析优化结果搭建了基于LiNbO3晶体的透射式共光轴体全息存储实验系统,实现了高分辨图像的记录与再现。与传统的双轴系统相比,所搭建的共光轴系统具有光路结构紧凑的特点。     

Persistent light-induced absorption in oxidized iron-doped barium titanate crystals

Illumination of oxidized iron-doped BaTiO(3) crystals with visible or ultraviolet light yields absorption changes of as much as 1300 m(-1) that are stable at room temperature. These photochromic effects cannot be erased by light, but heating the crystal to a moderate temperature (100 degrees C) can switch it back to its initial state. These effects, in particular the optical irreversibility, might be of interest, e.g., for optical control of charge-transport properties and for persistent data storage.     

Hybrid multinary modulation using a phase modulating spatial light modulator and a low-pass spatial filter

We propose a method for performing binary intensity and continuous phase modulation of beams with a spatial light modulator (SLM) and a low-pass spatial filtering 4-f system. With our method it is possible to avoid the use of phase masks in holographic data storage systems or to enhance the phase encoding of the SLM by making it capable of binary amplitude modulation. The data storage capabilities and the limitations of the method are studied.     

Ground motion improvements in SPEAR3

SPEAR3 is a third-generation synchrotron light source storage ring, about 234 meters in circumference.To meet the beam stability requirement, our goal is to ultimately achieve an orbit variation(relative to the photon beam lines) of less than 10% of the beam size, which is about 1 micron in the vertical plane. Hydrostatic leveling system(HLS) measurements show that the height of the SPEAR3 tunnel floor can vary by tens of microns daily without thermal insulation improvements. We present an analysis of the HLS data that shows that adding thermal insulation to the concrete walls of the storage ring tunnel dramatically decreased diurnal tunnel floor motion.     

Transmission type twisted nematic liquid crystal display for three gray-level phase-modulated holographic data storage systems

Gray-level data pages enhance the storage capacity of holographic data storage systems. A balanced three gray-scale data page in phase mode produces a homogenized Fourier spectrum which is regarded to be necessary for suitable exploitation of the holographic recording medium. A commercially available transmission type twisted nematic liquid crystal display has been characterized for use as a phase spatial light modulator with phase modulation in the range 0–3π/2 at 532 nm wavelength, such that it may be used for holographic data storage with binary as well as three gray-level phase-modulated data pages. Experimental results of the phase and amplitude modulation characteristics of the SLM, Fourier plane homogeneity, and recording of phase-modulated binary, three gray-level data pages and their reconstruction with a real-time holographic interferometric method are presented.     

Suppression of the photoinduced light scattering in LiNbO3:Fe by redox treatment and incoherent homogeneous illumination

In this paper, the redox treatment and incoherent homogeneous illumination were tried for the suppression of the photoinduced light scattering in LiNbO₃:Fe. Meanwhile, the effects of both the redox treatment and incoherent homogeneous illumination on the holographic storage properties of LiNbO₃:Fe were also studied. Our experimental data show that the reduction treatment sacrifices the diffraction efficiency for the suppression of photoinduced light scattering in LiNbO₃:Fe. By contrast, incoherent homogeneous illumination with the wavelength of 460 nm is efficient to suppress the photoinduced light scattering without any tradeoff on the holographic storage performance of LiNbO₃:Fe. The superiority of homogeneous illumination over the reduction treatment was attributed to the untouched acceptor concentration under the homogeneous illumination.     

Novel Bilayer Structures for Short Wavelength High Density Magneto-Optical Data Storage

We report a novel bi-layer thin film structure for high density magneto-optical (MO) data storage, which combines the advantages of blue wavelength and magnetically induced superresolution (MSR) recording. A double-layer system of exchange-coupled light rare-earth (LRE) element doped NdGdFeCo and traditional TbFeCo is used as the recording medium. The experimental results demonstrate that this NdGdFeCo/TbFeCo double layer has large Kerr rotation under blue wavelength. Centre aperture detection (CAD) MSR effect with temperature rising is also observed. Theoretical calculation is also carried out to verify the experimental results. These results collectively suggest that the new bilayer structure is very promising in next generation high density MO data storage.     

Two- and three-body kinematical correlation in the dissociative recombination of H(3)(+)

Fragmentation patterns for dissociative recombination of the triatomic hydrogen molecular ion H(3)(+) in the vibrational ground state have been measured using the storage ring technique and molecular fragment imaging. A broad distribution of vibrational states in the H(2) fragment after two-body dissociation and a large predominance of nearly linear momentum geometries after three-body dissociation are found. The fragmentation results are directly contrasted with Coulomb explosion imaging data on the initial H(3)(+) geometry, compared to existing wave-packet calculations, and considered in the light of a simple physical picture.     

阶梯型纳米孔径的近场光学局域增强特性研究

提出一种高分辨力与高通光效率兼备的阶梯型纳米孔径设计方法 ,孔径的尺寸从膜层的入射表面向出射表面呈阶梯型逐渐减小 ,直到在膜层的出射表面形成一个亚波长的小孔。采用三维时域有限差分 (FDTD)方法对方形阶梯型纳米孔径及三角形阶梯型纳米孔径进行了数值模拟计算。结果表明 ,由于近场光学很强的局域场增强效应 ,其通光效率与输出光强极大值在具有相同近场光斑尺寸情况下 ,较普通的非阶梯型纳米孔径提高了两个数量级 ,甚至更高 ,有效地提高了输出光功率。采用四台阶三角形阶梯型纳米孔径 ,当光斑半峰全宽为 97nm× 74nm时 ,出射光强极大值达到 10 4 9.76 ,较入射光增强了 10 0 0倍 ,而通光效率大于 1,达到 1.6 7。这种阶梯型纳米孔径可以直接作为纳米孔径激光器的出射孔径提高其输出光功率 ,也可以作为独立的光学屏对入射光进行整形得到具有高输出功率的亚波长尺度光源 ,在纳米尺度光学成像、光谱探测、数据存储、光刻、光学操作等近场光学应用领域具有潜在的应用前景。     

基于菌紫质F态的永久光存储研究

在线偏振飞秒激光激发下, 菌紫质通过双光子光化学反应可以生成具有永久光致各向异性的蓝移产物F₅₄₀态. 基于F₅₄₀态的永久光致各向异性, 通过调控飞秒激光空间光场分布, 可以在菌紫质薄膜中实现永久光信息存储. 本文使用纯相位型空间光调制器调制飞秒激光光场, 在物镜焦平面上生成光学点阵图案, 可以将信息快速记录在菌紫质薄膜中. 同时, 通过改变入射激光偏振方向, 可以实现偏振复用光存储, 这在高密度光存储和数据加密领域具有潜在应用.     

BR-D96N薄膜共线全息图像存储实验研究

摘要:     利用一种生物光致变色材料—基因突变菌紫质BR-D96N薄膜的光致变色特性,实现了可擦写式共线全息图像存储实验.对于光密度为3.0的BR-D96N薄膜,在700 mW/cm2的记录光强下（波长为632.8 nm,物光、参考光光强比为约1:1.2）,全息图建立的最佳曝光时间约为3s,最佳再现光强约为50 mW/cm2,全息图寿命约为10 min.实验表明：共线全息存储技术光学系统简单,系统体积小,受存储环境的影响低,并能够实现高密度存储|同时也实验验证了BR-D96N薄膜具有响应速度快,感光灵敏度高,擦写次数高,稳定耐用,使用方便等优点,可以作为一种较灵敏的可擦写共线全息记录介质.     

Optical data storage in microfibers

Tests of optical data storage in arrays of microfibers confirm its applicability and potential for higher storage densities than those achievable with conventional holographic data storage. Arrays of single-mode microfibers, spaced 0.78 microm apart and 60 microm long, were generated in a photopolymer film with four laser beams and simultaneously inscribed with Lippmann-Bragg fringes by use of a counterpropagating beam. Following the curing steps, spectra of white light retroreflected from a single fiber exhibit the reconstructed spectral lines of the multiwavelength laser used in the recording step; 10(11) bits/cm(2), or 10(13) bits on a compact disk, appear to be recordable.     

敏化光波长对(Fe,Ni):LiNbO3晶体全息记录性能的影响

分别采用514 nm绿光、488 nm蓝光和390 nm紫外光作为敏化光,633 nm红光作为记录光,详细研究了敏化光波长对氧化(Fe,Ni):LiNbO3晶体全息记录性能的影响.结果表明:随着敏化光波长的逐渐减小,氧化(Fe,Ni):LiNbO3晶体的非挥发全息记录性能逐渐优化,390 nm紫外光是这三种敏化光中最优的敏化光.考虑敏化光的吸收,为了在双中心全息记录中获得最优的性能,应当选择合适波长的敏化光:一方面短波长敏化光能有效地敏化深中心;另一方面短波长敏化光的吸收太强(如对光折变效应无用的基质吸收),不能沿厚度方向有效地敏化晶体,所以实际上需折衷考虑,并从理论上给予了解释.     

Nonlinear response studies and corrections for a liquid crystal spatial light modulator

The nonlinear response of light transmission characteristics of a liquid crystal (LC) spatial light modulator (SLM) is studied. The results show that the device exhibits a wide range of variations with different control parameters and input settings. Experiments were performed to obtain intensity modulation that is best described by either power-law or sigmoidal functions. Based on the inverse transformation, an appropriate pre-processing scheme for electrically addressed input gray-scale images, particularly important in several optical processing and imaging applications, is suggested. Further, the necessity to compensate the SLM image nonlinearities in a volume holographic data storage and retrieval system is demonstrated.     

Holographic recording in LiNbO3 using various polarized lights

Holographic recordings in a LiNbO₃ crystal using ordinary and extraordinary light in transmission-type geometry were performed. The system parameters of storage capacity (M/#), sensitivity, and signal-to-noise ratio were measured. Although extraordinary light will induce stronger fanning light (nonlinear enhanced scattered light) in LiNbO₃, our experimental results indicate that the system using extraordinary light is superior to that using ordinary light. Our demonstrations and results can help to optimize the holographic recording in some applications of volume holographic optical element (VHOE), such as wavelength division multiplexing (WDM) filters in optical communication.     

Investigation of Near-Field Imaging Characteristics of Radial Polarization for Application to Optical Data Storage

Radially polarized incident light can generate a more confined longitudinal electric field on a focal plane in near-field (NF) optics than focusing circularly polarized light. Using this phenomenon, it is feasible to reduce beam spot size on storage media to increase the areal density of optical data storage. A radially polarized beam generates a beam spot which is 20% more confined on the 1st surface of medium than that of circularly polarized light. However, the peak intensity of total electric field sharply decreases and its transverse component is much more dominant inside the media stack. This confirms that radially polarized optics can be a candidate not for an NF recording system but for an NF read-only memory (ROM) system. Potentially, the results could be useful to understand the effect of radial and circular polarizations inside and outside medium for various applications of NF optics.     

折射率失配对双光子三维光存储中像差的影响

双光子吸收三维光信息存储是实现高密度光存储的重要方法。三维数据写入过程中光束需经过两层不同的介质(如空气和存储材料),对像差和存储效果产生很大的影响,因此在理论和实验上分析系统各项光学参量对折射率失配引起的像差和存储效果的影响具有很大的意义。首先建立光学存储系统模型,在平行平板条件下,利用波像差函数推导展开,获得五项初级(赛德耳)像差,即球差、彗差、像散、场曲、畸变,然后对于存储材料在水平和倾斜两种情况下对初级像差进行模拟计算与分析,理论模拟与实验表明:物镜的数值孔径越大,像差随着存储深度增加而增大的速度就越快。