Temperature‐induced aggregation of the copolymers of N‐isopropylacrylamide and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate in aqueous solutions

A series of random copolymers of N‐isopropylacrylamide (NIPAM) and sodium 2‐acrylamido‐2‐methyl‐1‐propanesulphonate (AMPS) was synthesized by free‐radical copolymerization. The content of AMPS in the copolymers ranged from 1.1 to 9.6 mol %. The lower critical‐solution temperature (LCST) of copolymers in water increased strongly with an increasing content of AMPS. The influence of polymer concentration on the LCST of the copolymers was studied. For the copolymers with a higher AMPS content, the LCST decreased faster with an increasing concentration than for copolymers with a low content of AMPS. For a copolymer containing 1.1 mol % of AMPS the LCST dropped by about 3 °C when the concentration increased from 1 to 10 g/L, whereas for a copolymer containing 9.6 mol % of AMPS the LCST dropped by about 10 °C in the concentration range from 2 to 10 g/L. It was observed that the ionic strength of the aqueous polymer solution very strongly influences the LCST. This effect was most visible for the copolymer with the highest content of AMPS (9.6 mol %) for which an increase in the ionic strength from 0.2 to 2.0 resulted in a decrease in the LCST by about 27 °C (from 55 to 28 °C), whereas for the copolymer containing 1.1 mol % of AMPS the LCST decreased only by about 6 °C (from 37 to 31 °C) when the ionic strength increased from 0.005 to 0.3. The reactivity ratios for the AMPS and NIPAM monomer pairs were determined using different methods. The values of r_AMPS and r_NIPAM obtained were 11.0–11.6 and 2.1–2.4, respectively. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 2784–2792, 2001     

Influence of multiple stimuli on the lower critical solution temperature of new cationic poly(N‐acryloyl‐N′‐ethylpiperazine‐co‐N‐isopropylacrylamide) solutions

New multi‐stimuli responsive cationic copolymers based on N‐acryloyl‐N′‐ethyl piperazine (AcrNEP) and N‐isopropylacrylamide (NIPAM) were prepared by thermal free‐radical solution polymerization in dioxane at 75 °C. The chemical composition of the copolymers was determined by ¹H NMR spectroscopy and was found that the copolymers were slightly rich in NIPAM content than that of AcrNEP. The reactivity of the two monomers for the copolymerization reaction was evaluated by the extended Kelen‐Tüdös method. The distribution of monomer sequence in the copolymer chain was estimated using the terminal copolymerization model. The maximum tendency to alternation (～ 70%) was at 60 mol % of AcrNEP in the monomer feed. The copolymers were readily soluble in water at room temperature at all compositions and exhibited well‐defined lower critical solution temperature (LCST) phenomenon. The influence of various stimuli such as pH, temperature, simple inorganic salts, and surfactants on the LCST of the copolymers was studied in detail. Simple inorganic salts such as sodium chloride, sodium bromide, and sodium sulfate showed a salting‐out effect while sodium iodide showed a salting‐in effect. The salting‐out coefficient of the salts were calculated using the Sestchenow method, and the salting trend followed the order SO₄^2? > Cl^? > Br^? > I^?. The divalent salt was more effective in lowering the LCST than the monovalent salts. The cationic surfactant hexadecyl trimethylammonium bromide at concentrations above the critical micelle concentration caused a gradual increase in the LCST of the copolymer solutions. The intrinsic viscosity and light scattering behavior of the copolymers in water and in sodium chloride solutions were studied in detail. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 1175–1183     

Synthesis and functionalities of poly(N‐vinylalkylamide). XII. Synthesis and thermosensitive property of poly(vinylamine) copolymer prepared from poly(N‐vinylformamide‐co‐N‐vinylisobutyramide)

The differences in the polymerization abilities of N‐vinylformamide (NVF) and N‐vinylisobutyramide (NVIBA) and the synthesis of their copolymers were studied. The polymerization abilities were fairly good and quite similar to those of N‐vinyl‐ acetamide (NVA), a monomer in the same class as N‐vinylalkylamides. Since the monomer reactivity ratios were r₁ = 1.08 and r₂ = 0.92 (M₁ = NVF, M₂ = NVIBA), respectively, it is clear that the comonomers definitely were converted to random copolymers. The resulting copolymers poly(NVF‐co‐NVIBA) exhibited the cloud points sharply. The light transmittance profiles were the same as those for poly(NVIBA) although they increased from 39 °C for poly(NVIBA), with an increase in the corresponding hydrophilic NVF component. Our final objective was to produce a cloud point controlled polymer material with primary amino groups. To achieve this, we examined the hydrolysis of poly(NVF), poly(NVA), poly(NVIBA), and poly(NVF‐co‐NVIBA) to obtain poly(vinylamine) [poly(VAm)]. The hydrolytic cleavage of poly(NVF) and poly(NVA) was promoted by an increase in temperature. However, poly(NVIBA) was not cleaved appreciably. The hydrolysis of poly(NVF‐co‐NVIBA) was done under controlled conditions, and amino groups selectively were introduced to only one of two components of the copolymer. The cloud point of the hydrolyzed copolymer shifted to a higher temperature than that of the copolymer. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3674–3681, 2000     

“Smart” poly(2‐(dimethylamino)ethyl methacrylate‐ran‐9‐(4‐vinylbenzyl)‐9H‐carbazole) copolymers synthesized by nitroxide mediated radical polymerization

A series of poly(2‐(dimethylamino)ethyl methacrylate‐ran‐9‐(4‐vinylbenzyl)‐9H‐carbazole) (poly(DMAEMA‐ran‐VBK)) random copolymers, with VBK molar feed compositions f_VBK,0 = 0.02–0.09, were synthesized using 10 mol % [tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino] nitroxide (SG1) relative to 2‐([tert‐butyl[1‐(diethoxyphosphoryl)‐2,2‐dimethylpropyl]amino]oxy)‐2‐methylpropionic acid (BlocBuilder) at 80 °C and 90 °C. Controlled polymerizations were observed, even with f_VBK,0 = 0.02, as reflected by a linear increase in number average molecular weight (M_n) versus conversion X ≤ 0.6 with final copolymers characterized by relatively narrow, monomodal molecular weight distributions (M_w/M_n ≈ 1.5). Poly(DMAEMA‐ran‐VBK) copolymers were deemed sufficiently pseudo‐“living” to reinitiate a second batch of N,N‐dimethylacrylamide (DMAA), with very few apparent dead chains, as indicated by the monomodal shift in the gel permeation chromatography chromatograms. Poly(DMAEMA‐ran‐VBK) random copolymers exhibited tuneable lower critical solution temperature (LCST), in aqueous solution, by modifying copolymer composition, solution pH and by the addition of the water‐soluble poly(DMAA) segment. ¹H NMR analysis determined that, in water, the VBK units of the poly(DMAEMA‐ran‐VBK) random copolymer were segregated to the interior of the copolymer aggregate regardless of solution temperature and that poly(DMAEMA‐ran‐VBK)‐b‐poly(DMAA) block copolymers formed micelles above the LCST. In addition, the final random copolymer and block copolymer exhibited temperature dependent fluorescence due to the VBK units. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Effects of salts and copolymer composition on the lower critical solution temperature of poly(methyl 2‐acetamidoacrylate‐co‐methyl methacrylate) solutions

Copolymerizations of methyl 2‐acetamidoacrylate (MAA) with methyl methacrylate (MMA) were carried out at 60 °C in chloroform. Copolymers containing MAA units in the range of 83–90 mol % exhibited a lower critical solution temperature (LCST), although homopolymers of MAA and MMA did not. The LCST of polymer solutions decreased with (1) an increase in the concentration of the copolymer, (2) a decrease in the MAA content in the copolymer, and (3) an increase in the concentration of salts added. The effectiveness of anionic species for reducing the LCST is NO < Cl^? < SO < SO. Divalent anion is more effective for lowering the LCST than monovalent anion. However, there is no difference between cationic species in the salting‐out effect. Sodium carbonate and sodium phosphate had a salting‐in effect. Salting‐out coefficients were evaluated from the relationship between the logarithm of solubility of the copolymers and the salt concentration. Salting‐out coefficients of the copolymer depended not on the composition of the copolymers but on the salt added. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1945–1951, 2002     

Temperature‐induced phase transition of poly(N‐n‐propylacrylamide‐co‐butyl methacrylate‐co‐N,N‐diethylaminoethyl methacrylate)

Terpolymers composed of N‐n‐propylacrylamide (NPAAm), butyl methacrylate (BMA), and N,N‐diethylaminoethyl methacrylate (DEAEMA) were prepared in an attempt to investigate the temperature‐induced phase transition and its mechanism. Poly(NPAAm) showed the lower critical solution temperature (LCST) around 24°C in water. With the incorporation of DEAEMA with NPAAm, the LCST change was characterized by an initial increase. However, the LCST was shifted to the lower temperature at the later stage. This might be explained in terms of hydrophilic/hydrophobic contribution of DEAEMA to the LCST. The swelling behavior of copolymer gel in the various solvents and spin‐lattice relaxation time (T₁) study by NMR strongly suggested the hydrophilic/hydrophobic contribution of DEAEMA to the LCST depending on the local environment. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1407–1411, 1999     

Radical copolymerization of chlorotrifluoroethylene with 4‐bromo‐3,3,4,4‐tetrafluorobut‐1‐ene

The radical copolymerization of chlorotrifluoroethylene (CTFE) with 3,3,4,4‐tetrafluoro‐4‐bromobut‐1‐ene (BTFB) initiated by tert‐butylperoxypivalate is presented. The microstructures of the obtained copolymers are determined by means of NMR spectroscopies and elemental analysis and show that random copolymers were obtained. A wide range of poly(CTFE‐co‐BTFB) copolymers is synthesized, containing from 17 to 89 mol % of CTFE. In all the cases, CTFE is the less reactive of both comonomers. T_d^10% values, ranging from 163 up to 359 °C, are dependent on the BTFB content. These variations of thermal property are attributed to the increase in the number of C‐H and C‐Br bonds breakdown when the BTFB molar percentage in the copolymer is higher. T_g values range from 19 to 39 °C and a decreasing trend is observed when increasing the amount of BTFB in the copolymer. This observation arises from the higher flexibility of the copolymer when increasing the number of fluorobrominated lateral chains. These original fluoropolymers bearing reactive pendant bromo groups are suitable candidates for various applications. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1714–1720     

Solubility behavior of amphiphilic block and random copolymers based on 2‐ethyl‐2‐oxazoline and 2‐nonyl‐2‐oxazoline in binary water–ethanol mixtures

The solution properties of random and block copolymers based on 2‐ethyl‐2‐oxazoline (EtOx) and 2‐nonyl‐2‐oxazoline (NonOx) were investigated in binary solvent mixtures ranging from pure water to pure ethanol. The solubility phase diagrams for the random and block copolymers revealed solubility (after heating), insolubility, dispersions, micellization as well as lower critical solution temperature (LCST) and upper critical solution temperature behavior. The random and block copolymers containing over 60 mol % pNonOx were found to be solubilized in ethanol upon heating, whereas the dissolution temperature of the block copolymers was found to be much higher than for the random copolymers due to the higher extent of crystallinity. Furthermore, the block copolymer containing 10 mol % pNonOx exhibited a LCST in aqueous solution at 68.7 °C, whereas the LCST for the random copolymer was found to be only 20.8 °C based on the formation of hydrophobic microdomains in the block copolymer. The random copolymer displayed a small increase in LCST up to a solvent mixture of 9 wt % EtOH, whereas further increase of ethanol led to a decrease in LCST, which is probably due to the “water‐breaking” effect causing an increased attraction between ethanol and the hydrophobic part of the copolymer. In addition, the EtOx‐NonOx block copolymers revealed the formation of micelles and dynamic light scattering demonstrated that the micellar size is increasing with increasing the ethanol content due to the enhanced solubility of EtOx. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 515–522, 2009     

Thermo‐ and pH‐responsive gradient and block copolymers based on 2‐(2‐methoxyethoxy)ethyl methacrylate synthesized via atom transfer radical polymerization and the formation of thermoresponsive surfaces

A series of gradient and block copolymers, based on 2‐(2‐methoxyethoxy)ethyl methacrylate (MEO₂MA) and tert‐butyl acrylate (^tBA), were synthesized by atom transfer radical polymerization (ATRP) in a first step. The MEO₂MA monomer leads to the production of thermosensitive polymers, exhibiting lower critical solution temperature (LCST) at around room temperature, which could be adjusted by changing the proportion of ^tBA in the copolymer. In a second step, the tert‐butyl groups of ^tBA were hydrolyzed with trifluoroacetic acid to form the corresponding block and gradient copolymers of MEO₂MA and acrylic acid (AA), which exhibited both temperature and pH‐responsive behavior. These copolymers showed LCST values strongly dependent on the pH. At acid pH, a slightly decrease of LCST with an increase of AA in the copolymer was observed. However, at neutral or basic conditions, ionization of acid groups increases the hydrophilic balance considerably raising the LCST values, which even become not observable over the temperature range under study. In the last step, these carboxylic functionalized copolymers were covalently bound to biocompatible and biodegradable films of poly(3‐hydroxybutyrate‐co‐3‐hydroxyhexanoate) [P(HB‐co‐HHx)] obtained by casting and, previously treated with ethylenediamine (ED) to render their surfaces with amino groups. Thereby, thermosensitive surfaces of modified P(HB‐co‐HHx) could be obtained. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and self‐assembly of thermosensitive double‐hydrophilic poly(N‐vinylcaprolactam)‐b‐poly(N‐vinyl‐2‐pyrrolidone) diblock copolymers

We report on novel diblock copolymers of poly(N‐vinylcaprolactam) (PVCL) and poly(N‐vinyl‐2‐pyrrolidone) (PVPON) (PVCL‐b‐PVPON) with well‐defined block lengths synthesized by the MADIX/reversible addition‐fragmentation chain transfer (RAFT) process. We show that the lower critical solution temperatures (LCST) of the block copolymers are controllable over the length of PVCL and PVPON segments. All of the diblock copolymers dissolve molecularly in aqueous solutions when the temperature is below the LCST and form spherical micellar or vesicular morphologies when temperature is raised above the LCST. The size of the self‐assembled structures is controlled by the molar ratio of PVCL and PVPON segments. The synthesized homopolymers and diblock copolymers are demonstrated to be nontoxic at 0.1–1 mg mL^?1 concentrations when incubated with HeLa and HEK293 cancer cells for various incubation times and have potential as nanovehicles for drug delivery. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2725–2737     

Synthesis and self‐assembling of poly(N‐isopropylacrylamide‐block‐poly(L‐lactide)‐block‐poly(N‐isopropylacrylamide) triblock copolymers prepared by combination of ring‐opening polymerization and atom transfer radical polymerization

Novel thermo‐responsive poly(N‐isopropylacrylamide)‐block‐poly(l ‐lactide)‐block‐poly(N‐isopropylacylamide) (PNIPAAm‐b‐PLLA‐b‐PNIPAAm) triblock copolymers were successfully prepared by atom transfer radical polymerization of NIPAAm with Br‐PLLA‐Br macroinitiator, using a CuCl/tris(2‐dimethylaminoethyl) amine (Me₆TREN) complex as catalyst at 25 °C in a N,N‐dimethylformamide/water mixture. The molecular weight of the copolymers ranges from 18,000 to 38,000 g mol^?1, and the dispersity from 1.10 to 1.28. Micelles are formed by self‐assembly of copolymers in aqueous medium at room temperature, as evidenced by ¹H NMR, dynamic light scattering (DLS) and transmission electron microscopy (TEM). The critical micelle concentration determined by fluorescence spectroscopy ranges from 0.0077 to 0.016 mg mL^?1. ¹H NMR analysis in selective solvents confirmed the core‐shell structure of micelles. The copolymers exhibit a lower critical solution temperature (LCST) between 32.1 and 32.8 °C. The micelles are spherical in shape with a mean diameter between 31.4 and 83.3 nm, as determined by TEM and DLS. When the temperature is raised above the LCST, micelle size increases at high copolymer concentrations due to aggregation. In contrast, at low copolymer concentrations, decrease of micelle size is observed due to collapse of PNIPAAm chains. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3274–3283     

NMR investigation of effect of dissolved salts on the thermoresponsive behavior of oligo(ethylene glycol)‐methacrylate‐based polymers

The synthesis of thermo‐ and ionic‐responsive copolymers based on polyethylene glycol methyl ether methacrylate (OEGMA) and 2,2,2‐trifluoroethyl acrylate (TFEA) via reversible addition‐fragmentation chain transfer polymerization is described. Reactivity ratios for the copolymerization of OEGMA and TFEA are r_OEGMA = 2.46 and r_TFEA = 0.22, indicating that OEGMA is incorporated more rapidly than TFEA monomers. The copolymers are thermosensitive and exhibit volume phase transitions (lower critical solution behavior) at temperature, which depend on copolymer composition and the presence of added salts in the aqueous solutions. It was found that the copolymers exhibited LCST transitions at temperatures below 353 K only in salt solutions. ¹H NMR measurements indicated that motion of the protons located in and near the hydrophobic main chain are more sensitive to temperature than protons in the hydrophilic OEGMA side chains. The hydrophilic side chains remain largely hydrated; however, the presence of two distinct conformations of the terminal groups of the side chains was confirmed. The influence of OEGMA side chain length, copolymer composition, and salt type on aggregation behavior and dynamics was examined in detail. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2375–2385     

Morphological transitions in aggregates of thermosensitive poly(ethylene oxide)‐b‐poly(N‐isopropylacrylamide) block copolymers prepared via RAFT polymerization

Double hydrophilic poly(ethylene oxide)‐b‐poly(N‐isopropylacrylamide) (PEO‐b‐PNIPAM) block copolymers were synthesized via reversible addition‐fragmentation chain transfer (RAFT) polymerization, using a PEO‐based chain transfer agent (PEO‐CTA). The molecular structures of the copolymers were designed to be asymmetric with a short PEO block and long PNIPAM blocks. Temperature‐induced aggregation behavior of the block copolymers in dilute aqueous solutions was systematically investigated by a combination of static and dynamic light scattering. The effects of copolymer composition, concentration (C_p), and heating rate on the size, aggregation number, and morphology of the aggregates formed at temperatures above the LCST were studied. In slow heating processes, the aggregates formed by the copolymer having the longest PNIPAM block, were found to have the same morphology (spherical “crew‐cut” micelles) within the full range of C_p. Nevertheless, for the copolymer having the shortest PNIPAM block, the morphology of the aggregates showed a great dependence on C_p. Elongation of the aggregates from spherical to ellipsoidal or even cylindrical was observed. Moreover, vesicles were observed at the highest C_p investigated. Fast heating leads to different characteristics of the aggregates, including lower sizes and aggregation numbers, higher densities, and different morphologies. Thermodynamic and kinetic mechanisms were proposed to interpret these observations, including the competition between PNIPAM intrachain collapse and interchain aggregation. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4099–4110, 2009     

The effect of structure on the thermoresponsive nature of well‐defined poly(oligo(ethylene oxide) methacrylates) synthesized by ATRP

Statistical copolymers of di(ethylene glycol) methyl ether methacrylate (MEO₂MA) and tri(ethylene glycol) methyl ether methacrylate (MEO₃MA) were synthesized by atom transfer radical polymerization (ATRP) providing copolymers with controlled composition and molecular weights ranging from M_n = 8,300–56,500 with polydispersity indexes (M_w/M_n) between 1.19 and 1.28. The lower critical solution temperature (LCST) of the copolymers increased with the mole fraction of MEO₃MA in the copolymer over the range from 26 to 52 °C. The average hydrodynamic diameter, measured by dynamic light scattering, varied with temperature above the LCST. These two monomers were also block copolymerized by ATRP to form polymers with molecular weight of M_n = 30,000 and M_w/M_n from 1.12 to 1.21. The LCST of the block copolymers shifted toward the LCST of the major segment, as compared to the value measured for the statistical copolymers at the same composition. As temperature increased, micelles, consisting of aggregated PMEO₂MA cores and PMEO₃MA shell, were formed. The micelles aggregated upon further heating to precipitate as larger particles. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 194–202, 2008     

Synthesis of four‐armed poly(ε‐caprolactone)‐block‐poly(ethylene oxide) by diethylzinc catalyst

Biodegradable, amphiphilic, four‐armed poly(?‐caprolactone)‐block‐poly(ethylene oxide) (PCL‐b‐PEO) copolymers were synthesized by ring‐opening polymerization of ethylene oxide in the presence of four‐armed poly(?‐caprolactone) (PCL) with terminal OH groups with diethylzinc (ZnEt₂) as a catalyst. The chemical structure of PCL‐b‐PEO copolymer was confirmed by ¹H NMR and ¹³C NMR. The hydroxyl end groups of the four‐armed PCL were successfully substituted by PEO blocks in the copolymer. The monomodal profile of molecular weight distribution by gel permeation chromatography provided further evidence for the four‐armed architecture of the copolymer. Physicochemical properties of the four‐armed block copolymers differed from their starting four‐armed PCL precursor. The melting points were between those of PCL precursor and linear poly(ethylene glycol). The length of the outer PEO blocks exhibited an obvious effect on the crystallizability of the block copolymer. The degree of swelling of the four‐armed block copolymer increased with PEO length and PEO content. The micelle formation of the four‐armed block copolymer was examined by a fluorescent probe technique, and the existence of the critical micelle concentration (cmc) confirmed the amphiphilic nature of the resulting copolymer. The cmc value increased with increasing PEO length. The absolute cmc values were higher than those for linear amphiphilic block copolymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 950–959, 2004     

Miscibility of polysulfone blends with poly(1‐vinylpyrrolidone‐co‐styrene) copolymers and their interaction energies

The miscibility of polysulfone (PSf) with various hydrophilic copolymers was explored. Among these blends, PSf gave homogeneous mixtures with poly(1‐vinylpyrrolidone‐co‐styrene) [P(VP–S)] copolymers when these copolymers contained 68–88 wt % 1‐vinylpyrrolidone (VP). Miscible PSf blends with P(VP–S) copolymers underwent phase separation on heating caused by lower critical solution temperature (LCST)‐type phase behavior. The phase behavior depended on the copolymer composition. Changes in the VP content of P(VP–S) copolymers from 65 to 68 wt % shifted the phase behavior from immiscibility to miscibility and the LCST behavior. The phase‐separation temperatures of the miscible blends first increased gradually with the VP content, then went through a broad maximum centered at about 80 wt % VP, and finally decreased just before the limiting content of VP for miscibility with PSf. The interaction energies of binary pairs involved in PSf/P(VP–S) blends were evaluated from the phase‐separation temperatures of PSf/P(VP–S) blends with lattice‐fluid theory combined with a binary interaction model. The decrease in the contact angle between water and the membrane surface with increasing VP content in P(VP–S) copolymers indicated that the hydrophobic properties of PSf could be improved via blending with hydrophilic P(VP–S) copolymers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1401–1411, 2003     

Facile synthesis of triple‐stimuli (photo/pH/thermo) responsive copolymers of 2‐diazo‐1,2‐naphthoquinone‐mediated poly(N‐isopropylacrylamide‐co‐N‐hydroxymethylacrylamide)

A series of poly(N‐isopropylacrylamide‐co‐N‐hydroxymethylacrylamide) P(NIPAM‐co‐NHMA) copolymers were firstly synthesized via free radical polymerization. Then, the hydrophobic, photosensitive 2‐diazo‐1,2‐naphthoquinone (DNQ) molecules were partially and randomly grafted onto P(NIPAM‐co‐NHMA) backbone through esterification to obtain a triple‐stimuli (photo/pH/thermo) responsive copolymers of P(NIPAM‐co‐NHMA‐co‐DNQMA). UV‐vis spectra showed that the lower critical solution temperature (LCST) of P(NIPAM‐co‐NHMA) ascended with increasing hydrophilic comonomer NHMA molar fraction and can be tailored by pH variation as well. The LCST of the P(NIPAM‐co‐NHMA) went down firstly after DNQ modification and subsequently shifted to higher value after UV irradiation. Meanwhile, the phase transition profile of P(NIPAM‐co‐NHMA‐co‐DNQMA) could be triggered by pH and UV light as expected. Thus, a triple‐stimuli responsive copolymer whose solution properties could be, respectively, modulated by temperature, light, and pH, has been achieved. These stimuli‐responsive properties should be very important for controlled release delivery system. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2763–2773, 2009     

Synthesis of poly[N‐isopropylacrylamide‐g‐poly(ethylene glycol)] with a reactive group at the poly(ethylene glycol) end and its thermosensitive self‐assembling character

Poly[N‐isopropylacrylamide‐g‐poly(ethylene glycol)]s with a reactive group at the poly(ethylene glycol) (PEG) end were synthesized by the radical copolymerization of N‐isopropylacrylamide with a PEG macromonomer having an acetal group at one end and a methacryloyl group at the other chain end. The temperature dependence of the aqueous solutions of the obtained graft copolymers was estimated by light scattering measurements. The intensity of the light scattering from aqueous polymer solutions increased with increasing temperature. In particular, at temperatures above 40°C, the intensity abruptly increased, indicating a phase separation of the graft copolymer due to the lower critical solution temperature (LCST) of the poly(N‐isopropylacrylamide) segment. No turbidity was observed even above the LCST, and this suggested a nanoscale self‐assembling structure of the graft copolymer. The dynamic light scattering measurements confirmed that the size of the aggregate was in the range of several tens of nanometers. The acetal group at the end of the PEG graft chain was easily converted to the aldehyde group by an acid treatment, which was analyzed by ¹H NMR. Such a temperature‐induced nanosphere possessing reactive PEG tethered chains on the surface is promising for new nanobased biomedical materials. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1457–1469, 2006     

A new thermo‐responsive block copolymer with tunable upper critical solution temperature and lower critical solution temperature in the alcohol/water mixture

The multi‐thermo‐responsive block copolymer of poly[2‐(2‐methoxyethoxy)ethyl methacrylate]‐block‐poly[N‐(4‐vinylbenzyl)‐N,N‐diethylamine] (PMEO₂MA‐b‐PVEA) displaying phase transition at both the lower critical solution temperature (LCST) and the upper critical solution temperature (UCST) in the alcohol/water mixture is synthesized by reversible addition‐fragmentation chain transfer polymerization. The poly[2‐(2‐methoxyethoxy)ethyl methacrylate] (PMEO₂MA) block exhibits the UCST phase transition in alcohol and the LCST phase transition in water, while the poly[N‐(4‐vinylbenzyl)‐N,N‐diethylamine] (PVEA) block shows the UCST phase transition in isopropanol and the LCST phase transition in the alcohol/water mixture. Both the polymer molecular weight and the co‐solvent/nonsolvent exert great influence on the LCST or UCST of the block copolymer. By adjusting the solvent character including the water content and the temperature, the block copolymer undergoes multiphase transition at LCST or UCST, and various block copolymer morphologies including inverted micelles, core‐corona micelles, and corona‐collapsed micelles are prepared. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 4399–4412     

Synthesis and characterization of temperature‐sensitive block‐graft PNiPAAm‐b‐(PαN3CL‐g‐alkyne) copolymers by ring‐opening polymerization and click reaction

This study synthesized thermo‐sensitive amphiphilic block‐graft PNiPAAm‐b‐(PαN₃CL‐g‐alkyne) copolymers through ring‐opening polymerization of α‐chloro‐ε‐caprolactone (αClCL) with hydroxyl‐terminated macroinitiator poly(N‐isopropylacrylamide) (PNiPAAm), substituting pendent chlorides with sodium azide. This was then used to graft various kinds of terminal alkynes moieties by means of the copper‐catalyzed Huisgen's 1,3‐dipolar cycloaddition (“click” reaction). ¹H NMR, FTIR, and gel permeation chromatography (GPC) was used to characterize these copolymers. The solubility of the block‐graft copolymers in aqueous media was investigated using turbidity measurement, revealing a lower critical solution temperature (LCST) in the polymers. These solutions showed reversible changes in optical properties: transparent below the LCST, and opaque above the LCST. The LCST values were dependant on the composition of the polymer. With critical micelle concentrations (CMCs) in the range of 2.04–9.77 mg L^?1, the block copolymers formed micelles in the aqueous phase, owing to their amphiphilic characteristics. An increase in the length of hydrophobic segments or a decrease in the length of hydrophilic segments amphiphilic block‐graft copolymers produced lower CMC values. The research verified the core‐shell structure of micelles by ¹H NMR analyses in D₂O. Transmission electron microscopy was used to analyze the morphology of the micelles, revealing a spherical structure. The average size of the micelles was in the range of 75–145 nm (blank), and 105–190 nm (with drug). High drug entrapment efficiency and drug loading content were observed in the drug micelles. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011