Synthesis,self‐assembly and reversible healing of supramolecular perfluoropolyethers

The synthesis and thermomechanical properties of a novel class of self‐healing perfluoropolyethers (PFPEs) is reported. By decoration of 2‐ureido‐4[1H]‐pyrimidone end groups on the termini of low molar mass PFPE, the formation of supramolecular polymers and networks held together via hydrogen bonding associations was achieved. These novel supramolecular polymer materials exhibit a combination of enhanced modulus and elasticity, along with self‐healing properties, where rapid self‐healing time was demonstrated using dynamic rheological measurements. These types of supramolecular PFPEs are anticipated to be useful for a number of emerging areas in lubrication. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3598–3606     

Covalent functionalization of solid cellulose by divergent synthesis of chemically active dendrons

Covalent surface modification of solid cellulose with well‐defined and chemically reactive dendrons is introduced as a platform for cellulose grafting with functional materials. Surface functionalization with a first generation dendron is achieved by esterification employing bifunctional molecules based on 2,2‐bis(hydroxymethyl) propionic acid (bis‐MPA) under mild conditions and short reaction times. The activated cellulose surface displays hydrophobic properties and contains two reactive alkene end‐groups per graft, which are used for covalent binding to active agents, as demonstrated by selective functionalization of the modified cellulose with fluorescent dye via photopatterning. The number of active end‐groups on the surface of cellulose is multiplied by divergent solid‐state synthesis of second and third generation dendrons having four and eight reactive sites per dendron, respectively. The dendrons are assembled in only few hours by a sequence of thiol‐ene/esterification reactions. The ability to accurately control the number of binding sites on the surface of cellulose allows fine tuning of the surface properties, as shown by the attachment of hydrophobic small molecules to the dendronized cellulose. The first, second and third generation dendrons allow preparing surfaces with increasing hydrophobicities; second and third generation dendrons functionalized with small perfluoroalkyl molecule display superhydrophobic properties. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2103–2114     

3,6‐linked 9‐alkyl‐9H‐carbazole main‐chain polymers: Preparation and properties

An investigation into the preparation of poly(9‐alkyl‐9H‐carbazole‐3,6‐diyl)s with palladium catalyzed cross‐coupling reactions of 3‐halo‐6‐halomagnesio‐9‐alkyl‐9H‐carbazoles, generated in situ from their corresponding 3,6‐diiodo‐ and 3,6‐dibromo‐derivatives was undertaken. Monomers with a range of alkyl group substituents with different steric requirements were investigated and their effects on the polymerization were studied. The effects of the nature of halogen substituents on the polymerization reaction were also investigated. Structural analysis of the polymers revealed exclusive 3,6‐linkage between consecutive carbazole repeat units on the polymer chains. The physical properties of these polymers were investigated with spectroscopic, thermal gravimetric analysis, and electrochemical studies. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6041–6051, 2004     

Linear viscoelastic characteristics of in situ compatiblized binary polymer blends with viscoelastic properties of components variable

By Friedel‐Crafts alkylation reaction, catalyzed by a Lewis acid of anhydrous aluminum chloride (AlCl₃), binary polymer blends of polypropylene (PP)/polystyrene (PS) with volume proportion of 80/20 were in situ compatiblized and prepared in an XSS‐30 melt mixer at 210 °C. The linear viscoelastic characteristics of the blends were investigated by checking the variations of storage modulus, loss modulus, complex modulus, and complex viscosity of the in situ compatiblized blends, which were dependent on AlCl₃ content. In addition, Han plots of the in situ compatiblized blends with different AlCl₃ content were also used to characterize the linear viscoelastic properties of the blends. The results showed that both the dynamic rheological parameters and the Han plots were obviously influenced by the rheological properties of the matrix and slightly influenced by the rheological properties of the dispersed phase. Further investigations revealed that phase geometry contributions to the dynamic rheological parameters of the blends could be ignored in comparison with the contributions of the components and the interfacial modification, which were defined and obtained according to log‐linear‐additivity rule. The linear viscoelastic characteristics of the blends were mainly controlled by the combination of the effects of interfacial modification between phases and the rheological properties of the matrix. Storage modulus is the most sensitive dynamic rheological parameter to characterize the interfacial compatiblization effects in the in situ compatiblized binary polymer blends with rheological properties of components variable. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1349–1362, 2010     

Diels–Alder reaction with anthracene and quinone derivatives on the dendritic periphery

Diels–Alder (DA) adducts including 24, 48, and 96 bicyclo end groups on the dendritic periphery were prepared by the reaction of anthracene on the dendrimers (first to fourth generation) and 1,4‐benzoquinone as well as 1,4‐naphtoquinone in boiled toluene. The structural information of DA adducts on the dendritic periphery was received from the hyperfine structural analysis by ¹H NMR spectroscopy. The gel permeation chromatography of DA products revealed very low polydispersity values and decreased regular retention time according to increasing generation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2155–2161, 2004     

Physical gelation and macromolecular mobility of sustainable polylactide during isothermal crystallization

The mobility of free macromolecular chains is of importance to the growth of crystallites in a crystallizing sustainable polylactide (PLA), which was scarcely explored by rheology. In this study, the time‐resolved rheological properties for PLA during isothermal crystallization were investigated first, showing that the storage and loss modulus experience 2–3 decades of increase. The Avrami analysis reveals that the crystallization kinetics in rheological measurement protocol follows the homogeneous nucleation and three‐dimensional growth mechanism. The linear viscoelastic properties in the vicinity of physical gelation point were then studied at the inverse quenching temperature of 165 °C. The results show that physical gelation occurs when the critical absolute crystallinity reaches 13% as determined by the rheological method. Relaxation time spectra reveal that the interfacial relaxation is greatly retarded but the presence of growing spherulites possesses little constraint on the mobility of free chains in matrix especially before physical gelation point. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1235–1244     

Extension of the chain‐end,free‐volume theory for predicting glass temperature as a function of conversion in hyperbranched polymers obtained through one‐pot approaches

Compared with linear polymers, more factors may affect the glass‐transition temperature (T_g) of a hyperbranched structure, for instance, the contents of end groups, the chemical properties of end groups, branching junctions, and the compactness of a hyperbranched structure. T_g's decrease with increasing content of end‐group free volumes, whereas they increase with increasing polarity of end groups, junction density, or compactness of a hyperbranched structure. However, end‐group free volumes are often a prevailing factor according to the literature. In this work, chain‐end, free‐volume theory was extended for predicting the relations of T_g to conversion (X) and molecular weight (M) in hyperbranched polymers obtained through one‐pot approaches of either polycondensation or self‐condensing vinyl polymerization. The theoretical relations of polymerization degrees to monomer conversions in developing processes of hyperbranched structures reported in the literature were applied in the extended model, and some interesting results were obtained. T_g's of hyperbranched polymers showed a nonlinear relation to reciprocal molecular weight, which differed from the linear relation observed in linear polymers. T_g values decreased with increasing molecular weight in the low‐molecular‐weight range; however, they increased with increasing molecular weight in the high‐molecular‐weight range. T_g values decreased with increasing log M and then turned to a constant value in the high‐molecular‐weight range. The plot of T_g versus 1/M or log M for hyperbranched polymers may exhibit intersecting straight‐line behaviors. The intersection or transition does not result from entanglements that account for such intersections in linear polymers but from a nonlinear feature in hyperbranched polymers according to chain‐end, free‐volume theory. However, the conclusions obtained in this work cannot be extended to dendrimers because after the third generation, the end‐group extents of a dendrimer decrease with molecular weight. Thus, it is very possible for a dendrimer that T_g increases with 1/M before the third generation; however, it decreases with 1/M after the third generation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1235–1242, 2004     

Synthesis,characterization, and degradation of poly(anhydride‐co‐amide)s and their blends with polylactide

In attempt to improve the properties of polyanhydrides based on aliphatic anhydrides, we synthesized novel polyanhydrides containing amide groups in the main chains. In this work, N,N′‐bis(L ‐alanine)‐sebacoylamide (BSAM) was prepared from natural amino acid and sebacic acid (SA) and characterized by IR and ¹H NMR. In addition, polymers of PBSAM, P[1,6‐bis(P‐carboxyphenoxy) hexane (CPH)‐BSAM], and P(CPH‐SA), blends of P(CPH‐SA)/polylactide (PLA), P(CPH‐BSAM)/PLA were also prepared and characterized by IR, gel permeation chromatography, and differential scanning calorimetry. The hydrolytic degradation of polyanhydrides and their blends with PLA (number‐average molecular weight = 2.90 × 10⁵) was evaluated in 0.1 M phosphate buffer pH 7.4 at 37 °C. The results indicate that the existence of amide, aromatic, and ester bonds in the main chain of polymers slows down the degradation rate, and the tendency becomes clearer with the increasing amount of them, and the copolymers and their blends with PLA possess excellent physical and mechanical properties. These can make them more widely used in drug delivery and nerve regeneration. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4311–4317, 2004     

Synthesis and characterization of poly(L‐lactic acid)–poly(ε‐caprolactone) multiblock copolymers by melt polycondensation

An Erratum has been published for this article in J. Polym. Sci. Part A: Polym. Chem. (2004) 42(22) 5845 New multiblock copolymers derived from poly(L‐lactic acid) (PLLA) and poly(ε‐caprolactone) (PCL) were prepared with the coupling reaction between PLLA and PCL oligomers with ? NCO terminals. Fourier transform infrared (FTIR), ¹³C NMR, and differential scanning calorimetry (DSC) were used to characterize the copolymers and the results showed that PLLA and PCL were coupled by the reaction between ? NCO groups at the end of the PCL and ? OH (or ? COOH) groups at the end of the PLLA. DSC data indicated that the different compositions of PLLA and PCL had an influence on the thermal and crystallization properties including the glass‐transition temperature (T_g), melting temperature (T_M), crystallizing temperature (T_c), melting enthalpy (ΔH_m), crystallizing enthalpy (ΔH_c), and crystallinity. Gel permeation chromatography (GPC) was employed to study the effect of the composition of PLLA and PCL and reaction time on the molecular weight and the molecular weight distribution of the copolymers. The weight‐average molecular weight of PLLA–PCL multiblock copolymers was up to 180,000 at a composition of 60% PLLA and 40% PCL, whereas that of the homopolymer of PLLA was only 14,000. A polarized optical microscope was used to observe the crystalline morphology of copolymers; the results showed that all polymers exhibited a spherulitic morphology. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5045–5053, 2004     

End‐group effect on physical aging and polymer properties for poly(ether sulfones)

The physical aging properties of amorphous thermoplastics having various terminal groups were investigated with creep recovery and linear dilatometry. The structure of the chain end groups affected physical aging at lower molecular weights; however, above the critical molecular weight for entanglements the end‐group effect on aging diminished. Experimental densities and glass‐transition temperatures were also end‐group dependent. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2850–2860, 2003     

Structural effect of linear and star‐shaped poly(L‐lactic acid) on physical properties

The linear and star‐shaped poly(L‐lactic acid) (PLLA) with similar molecular weight were prepared and their physical properties such as thermal properties, rheological properties, and crystallization behavior in quiescent and dynamic states were compared. The differential scanning calorimetry showed that the linear PLLA gave higher glass transition, melting, and crystallization temperatures than the star‐shaped one. In dynamic crystallization, the linear PLLA gave longer induction time and longer overall crystallization time than the star‐shaped one, although the former gave higher rate of crystallization in quiescent crystallization. However, wide‐angle X‐ray diffractometer(WAXD) analysis revealed that the linear and star‐shaped PLLA developed the same crystal structure and application of shear had little effect on crystal structure. As predicted, the linear PLLA gave higher crystallinity than the star‐shaped PLLA. In the dilute solutions, the linear PLLA exhibited higher intrinsic viscosity than the star‐shaped one. In the concentrated solutions, the star‐shaped PLLA gave higher values of dynamic viscosity, storage, and loss moduli than the linear one. Further, the former exhibited more noticeable shear thinning behavior and greater dependence of rheological properties on temperature than the latter. For both PLLA melts, the modified Cole–Cole plot gave slope less than 2. Of two PLLA polymers the star‐shaped PLLA gave smaller slope than the linear one. In addition, the former showed greater change of the slope with temperature than the latter. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 939–946, 2004     

Novel synthesis of polyethylene–poly(dimethylsiloxane) copolymers with a metallocene catalyst

Polyethylene–poly(dimethylsiloxane) copolymers were synthesized in solution from an ethylene monomer and an ω‐vinyl poly(dimethylsiloxane) (PDMS) macromonomer at 363 and 383 K with EtInd₂ZrCl₂/methylaluminoxane as a catalyst. The copolymers obtained were characterized with Fourier transform infrared spectroscopy, ¹H and ¹³C NMR, size exclusion chromatography, and differential scanning calorimetry. The rheological properties of the molten polymers were determined under dynamic shear flow tests at small‐amplitude oscillations, whereas the physical arrangement of the phase domains was analyzed with scanning electron microscopy (SEM)/energy dispersive X‐ray (EDX). The analysis of the catalyst activity and the resulting polymers supported the idea of PDMS blocks or chains grafted to polyethylene. The changes in the rheological behavior and the changes in the Fourier transform infrared and NMR spectra were in agreement with this proposal. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2462–2473, 2004     

Physical properties of glycosaminoglycan hydrogels

The chemical composition of glycosaminoglycan (GAG) hydrogels was found to have a profound effect on the physical properties of gels. Hyaluronan (HA) and chondroitin sulfate (CS) were each modified with adipic dihydrazide (ADH) with carbodiimide chemistry. The resulting polymer was crosslinked with various concentrations of poly(ethylene glycol) dialdehyde (PEG‐diald) to produce a series of hydrogels. The physical properties of these GAG hydrogels varied in a concentration‐dependent fashion. Maximal crosslinking was observed at a theoretical crosslinking of 50% for the HA‐ADH‐PEG‐diald hydrogels and 75% for the CS‐ADH‐PEG‐diald hydrogels. Adding PEG‐diald beyond the optimum for crosslinking prolonged the in vitro enzymatic degradation time of the hydrogels. The swelling of the crosslinked GAG hydrogels was correlated with the amount of PEG‐diald used rather than with the crosslinking density. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4344–4356, 2004     

Dynamics of supramolecular associative polymer networks at the interplay of chain entanglement,transient chain association,and chain‐sticker clustering

The dynamic mechanical properties of supramolecular associative polymer networks depend on the average number of entanglements along the network‐forming chains, N_e, and on their content of associative groups, f . In addition, there may be further influence by aggregation of the associative groups into clusters, which, in turn, is influenced by the chemical structure of these groups, and again by N_e and f of the polymer. Therefore, the effects of these parameters are interdependent. To conceptually understand this interdependency, we study model networks in which (a) N_e, (b) f , and (c) the chemical structure of the associative groups are varied systematically. Each network is probed by rheology. The clustering of the associative groups is assessed by analyzing the rheological data at the end range of frequency covered and by comparison of the number of supramolecular network junctions with the maximum possible number of binary transient bonds. We find that if the total number of the network junctions, which can be formed either by interchain entanglement or by interchain transient associations, is greater than a threshold of 13, then the likelihood of cluster formation is high and the dynamics of supramolecular associative polymer networks is mainly controlled by this phenomenon. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 1209–1223     

Effect of methyl substitution of the ethylene unit on the physical properties of poly(butylene succinate)

A series of poly(butylene succinate‐co‐butylene 2‐methyl succinate)s were prepared through variations in the molar fraction of succinic acid to 2‐methyl succinic acid, and the effects of methyl substitution on the shear‐induced crystallization, nonisothermal crystallization behavior, dynamic rheological properties, crystal morphology, and mechanical properties were investigated. Introducing 2‐methyl succinic units reduced the melting temperature and crystallization temperature; this indicated that the substituted units retarded crystallization of the polymer. The Avrami exponents, estimated by modified Avrami plots, ranged from 2.1 to 3.5 and were a little diminished by the substitution. The substitution also reduced the rate of crystallization under shear. However, the effect was diminished with an increasing shear rate because most polymer chains were more regularly arranged at higher shear rates. Dynamic experiments in the solid state revealed that the peak on a plot of the loss tangent against the temperature became sharper at higher contents of the substituted unit, and the peak temperature, the glass‐transition temperature, was reduced as the content of 2‐methyl succinic acid increased. Wide‐angle X‐ray diffraction patterns showed that there was little effect of the 2‐methyl succinic acid unit on the crystal morphology. The toughness of the polymer was abruptly increased up to 350% at the expense of the tensile modulus. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1759–1766, 2004     

Synthesis of hydrophilic/CO2‐philic poly(ethylene oxide)‐b‐poly(1,1,2,2‐tetrahydroperfluorodecyl acrylate) block copolymers via controlled/living radical polymerizations and their properties in liquid and supercritical CO2

Hydrophilic/CO₂‐philic poly(ethylene oxide)‐b‐poly(1,1,2,2‐tetrahydroperfluorodecyl acrylate) block copolymers were synthesized via reversible addition–fragmentation chain transfer (RAFT) polymerization, iodine transfer polymerization (ITP), and atom transfer radical polymerization (ATRP) in the presence of either degenerative transfer agents or a macroinitiator based on poly(ethylene oxide). In this work, both RAFT and ATRP showed higher efficiency than ITP for the preparation of the expected copolymers. More detailed research was carried out on RAFT, and the living character of the polymerization was confirmed by an ultraviolet (UV) analysis of the ? SC(S)Ph or ? SC(S)S? C₁₂H₂₅ end groups in the polymer chains. The quantitative UV analysis of the copolymers indicated a number‐average molecular weight in good agreement with the value determined by ¹H NMR analysis. The properties of the macromolecular surfactants were investigated through the determination of the cloud points in neat liquid and supercritical CO₂ and through the formation of water‐in‐CO₂ emulsions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2405–2415, 2004     

Dendronized polymers with tailored surface groups

A series of polymers tethered with bis‐MPA dendrons was synthesized by a combination of divergent growth and atom transfer radical polymerization (ATRP). Macromonomers of first and second generation were synthesized utilizing the acetonide protected anhydride of bis‐MPA as the generic esterfication agent. The macromonomers were polymerized in a controlled fashion by ATRP utilizing Cu(I)/Cu(II) and N‐propyl‐2‐pyridylmethanamine as the halogen/ligand system. The end‐groups of these polymers were further tailored to achieve hydroxyl, acetate, and aliphatic hexadecyl functionality. With this approach all polymers will emanate from the same backbone, enabling for an evaluation of both the generation and end‐group dependent properties. Furthermore, a dendronized tri‐block copolymer was synthesized. All materials were analyzed by ¹H and ¹³C NMR, as well as size‐exclusion chromatography (SEC). The SEC analysis revealed that the molecular weights of the divergently grown dendronized polymers increased with increasing generation while the polydispersity (PDI) was kept low. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3852–3867, 2005     

Rheological and mechanical properties of epoxy/polyurethane blends initiated by N‐benzylpyrazinium hexafluoroantimonate salt

In this work the cure behavior and rheological and mechanical interfacial properties of the diglycidylether of bisphenol A (DGEBA)/polyurethane (PU) blend system, initiated by 1 wt % N‐benzylpyrazinium hexafluoroantimonate as a latent thermal catalyst, were investigated. To characterize the mechanical interfacial properties of the system, the critical stress intensity factor (K_IC) was calculated with a single‐edge‐notched beam (SEN) beam fracture toughness test. And an impact test was performed at room and cryogenic temperatures to determine the performance of PU at room and low‐temperatures, respectively. As a result, the E_c of the blend system was increased with increasing PU content, showing a maximum value at 30 wt % PU, which was in good agreement with the mechanical properties of the blend system. Consequently, these results could be explained by the improvement that occurred in intermolecular hydrogen bonding between the hydroxyl group in EP and the isocyanate group in PU, resulting in increased compatibility of the components within the interpenetrating polymer networks. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3841–3848, 2004     

Bulk properties of dendronized polymers with tailored end‐groups emanating from the same backbone

Dendronized polymers with a methacrylate backbone bearing pendant aliphatic polyester dendrons based on 2,2‐bis(methylol)propionic acid have been investigated by rheological measurements, differential scanning calorimetry (DSC), size exclusion chromatography (SEC), and ¹H NMR self‐diffusion techniques. The change in material properties due to the attachment of larger dendrons and/or different end‐groups to a backbone of the same length is investigated. Dendronized polymers of the second to fourth generation with hydroxyl, acetonide, or hexadecyl end‐group functionalities have been studied. DSC revealed that the glass transition temperature of the amorphous polymers increases with increasing size of the dendrons, and that the ability for the hexadecyl functional polymers to crystallize decreases with increasing size of dendrons. ¹H NMR self‐diffusion and longitudinal relaxation data are consistent with an elongated rod‐like model of the polymers in solution. Larger dendrons lead to a larger rod diameter that approximately double when increasing the generation of dendronized polymer from two to four. Rheological measurements demonstrated that the complex viscosity at low frequency increased with dendron size. Independently of the functionality, the second and third generation samples initially showed a Newtonian plateau, followed by a shear thinning region at higher frequencies. The fourth generation samples only showed shear thinning over the whole frequency region. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4496–4504, 2005     

The effect of compatibilization and rheological properties of polystyrene and poly(dimethylsiloxane) on phase structure of polystyrene/poly(dimethylsiloxane) blends

The compatibilization effect of polystyrene (PS)‐poly(dimethylsiloxane) (PDMS) diblock copolymer (PS‐b‐PDMS) and the effect of rheological properties of PS and PDMS on phase structure of PS/PDMS blends were investigated using a selective extraction technique and scanning electron microscopy (SEM). The dual‐phase continuity of PS/PDMS blends takes place in a wide composition range. The formation and the onset of a cocontinuous phase structure largely depend on blend composition, viscosity ratio of the constituent components, and addition of diblock copolymers. The width of the concentration region of the cocontinuous structure is narrowed with increasing the viscosity ratio of the blends and in the presence of the small amount diblock copolymers. Quiescent annealing shifts the onset values of continuity. The experimental results are compared with the volume fraction of phase inversion calculated with various theoretical models, but none of the models can account quantitatively for the observed data. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 898–913, 2004