FTIR研究交联聚氨酯脲弹性体的结构对动态性能的影响

用傅立叶变换红外光谱法(FTIR)研究交换PUU的结构指出,化学交联键的存在使得氢键化的NH吸收位置向高波数方向移动,同时羰基区内完全有序的氢键化脲羰基(1642cm-1)吸收较弱,完全有序的氨酯羰基(1693cm-1)吸收谱带观察不到.随着温度的升高,氢键化的NH吸收强度逐渐减弱,谱带吸收位置向高波数方向移动.FTIR结果揭示了交联PUU弹性体内部微相混合程度较线性PUU的高,交联PUU弹性体的回弹性在同温度下小于线性PUU的回弹性,随温度的升高,交联PUU弹性体极性键间的氢键化作用较易破坏,分子的柔顺性增加较快,交联PUU的回弹性增加幅度较大.交联密度越大,回弹性越小,压缩生热越大.硬段含量越高,材料的生热现象越严重.扩链剂的用量增加,对交联PUU的回弹性和压缩生热影响不大,但它显著地改善了PUU的疲劳性能.     

Synthesis and properties of waterborne self‐crosslinkable sulfo‐urethane silanol dispersions

A novel type of crosslinkable waterborne polyurethane ionomer was prepared by the acetone process. Two new types of sulfonated diols compatible with this process were synthesized from dimethyl 5‐sodium sulfo isophthalate using a one‐ or two‐stage method. Isocyanate‐terminated polyurethane oligomers were prepared from the sulfonated diols with various combinations of diols and diisocyanates and subsequently reacted with amino silane derivatives. Stable, low‐volatile organic chemical, waterborne dispersions of the sulfo‐urethane silanol polymers spontaneously crosslink upon drying without extra additives or processing steps. Despite the lack of organic coalescing solvents, the dispersions have minimum film‐forming temperatures below 10 °C, regardless of glass‐transition temperature. Tensile strengths up to 6000 psi with elongations between 300 and 600% were obtained for the crosslinked films. The hard‐segment content of the films can be controlled to produce films with a Sward–Rocker hardness value up to 42. Through silane end‐group modification, the crosslinking density of the films can also be modified to produce polyurethanes with a wide range of physical properties. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3037–3045, 2002     

Effect of crosslink on the characteristic length of glass transition of network polymers

The characteristic length of the glass transition temperature was evaluated for crosslinked bulk polystyrenes and poly(methyl methacrylate)s by differential scanning calorimetry. The characteristic length, which corresponds to a length scale of the cooperative rearrangement due to polymer segmental relaxation, was revealed to decrease with increase in the degree of crosslink. The relative values of configurational entropy for crosslinked polymers were evaluated based on a simple polymer network model on a cubic lattice. As a result, the configurational entropy of the smallest cooperatively rearranging region was revealed to decrease with increase in the degree of crosslink, which is responsible for the above behavior of the characteristic length. The effects of crosslink on the characteristic length and the glass transition temperature were found to be stronger for crosslinked poly(methyl methacrylate)s than for crosslinked polystyrenes, which reflects the difference in the structure of crosslink segment. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1958–1966, 2006     

Dynamic mechanical behavior of acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) blends

The dynamic mechanical behavior of uncrosslinked (thermoplastic) and crosslinked (thermosetting) acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) (NBR/EVA) blends was studied with reference to the effect of blend ratio, crosslinking systems, frequency, and temperature. Different crosslinked systems were prepared using peroxide (DCP), sulfur, and mixed crosslink systems. The glass‐transition behavior of the blends was affected by the blend ratio, the nature of crosslinking, and frequency. sThe damping properties of the blends increased with NBR content. The variations in tan δ_max were in accordance with morphology changes in the blends. From tan δ values of peroxide‐cured NBR, EVA, and blends the crosslinking effect of DCP was more predominant in NBR. The morphology of the uncrosslinked blends was examined using scanning electron and optical microscopes. Cocontinuous morphology was observed between 40 and 60 wt % of NBR. The particle size distribution curve of the blends was also drawn. The Arrhenius relationship was used to calculate the activation energy for the glass transition of the blends, and it decreased with an increase in the NBR content. Various theoretical models were used to predict the modulus of the blends. From wide‐angle X‐ray scattering studies, the degree of crystallinity of the blends decreased with an increasing NBR content. The thermal behavior of the uncrosslinked and crosslinked systems of NBR/EVA blends was analyzed using a differential scanning calorimeter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1556–1570, 2002     

Molecular mobility of free‐radical‐functionalized carbon‐nanotube/siloxane/poly(urea urethane) nanocomposites

Multiwalled carbon nanotubes (MWNTs) were functionalized by a free‐radical reaction of vinyltriethoxysilane and were blended with poly(urea urethane) (PUU) containing poly(dimethylsiloxane) as a soft segment. PUU was end‐capped with aminopropyltriethoxysilane (A‐silane) or phenyltriethoxysilane (P‐silane).A‐silane‐end‐capped PUU was covalently bonded to functionalized MWNTs, whereas P‐silane‐end‐capped PUU was noncovalently bonded to pristine MWNTs by a π–π interaction. Fourier transform infrared, Raman spectra, and thermogravimetric analysis confirmed the functionalization of MWNTs. The results showed that the optimal reaction time of the functionalization of MWNT was 8 h, and the organic content of the modified carbon nanotubes reached 35.22%. Solid‐state nuclear magnetic resonance and dynamic mechanical analysis were used to investigate the molecular structure and molecular mobility of the carbon‐nanotube/PUU nanocomposites. A‐silane PUU covalently bonded to MWNTs showed a considerable reduction in the molecular motion of the soft segment, which led to the glass‐transition temperature decreasing from ?117 to ?127 °C as MWNTs were incorporated. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6084–6094, 2005     

Effect of nanotube functionalization on the properties of single‐walled carbon nanotube/polyurethane composites

A commercially available aliphatic thermoplastic polyurethane formulated with a methylene bis(cyclohexyl) diisocyanate hard segment and a poly(tetramethylene oxide) soft segment and chain‐extended with 1,4‐butanediol was dissolved in dimethylformamide and mixed with dispersed single‐walled carbon nanotubes. The properties of composites made with unfunctionalized nanotubes were compared with the properties of composites made with nanotubes functionalized to contain hydroxyl groups. Functionalization almost eliminated the conductivity of the tubes according to the conductivity of the composites above the percolation threshold. In most cases, functionalized and unfunctionalized tubes yielded composites with statistically identical mechanical properties. However, composites made with functionalized tubes did have a slightly higher modulus in the rubbery plateau region at higher nanotube fractions. Small‐angle X‐ray scattering patterns indicated that the dispersion reached a plateau in the unfunctionalized composites that was consistent with the plateau in the rubbery plateau region. The room‐temperature modulus and tensile strength increase was proportionally higher than almost all increases seen previously in thermoplastic polyurethanes; however, the increase was still an order of magnitude below what has been reported for the best nanotube–polymer systems. Nanotube addition increased the hard‐segment glass transition temperature slightly, whereas the soft‐segment glass transition was so diffuse that no conclusions could be drawn. Unfunctionalized tubes suppressed the crystallization of the hard segment; whereas functionalized tubes had no effect. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 490–501, 2007     

Divinylsiloxane‐bisbenzocyclobutene‐based polymer modified with polystyrene–polybutadiene–polystyrene triblock copolymers

Divinylsiloxane‐bisbenzocyclobutene (DVS‐bisBCB) polymer has very low dielectric constant and dissipation factor, good thermal stability, and high chemical resistance. The fracture toughness of the thermoset polymer is moderate due to its high crosslink density. A thermoplastic elastomer, polystyrene–polybutadiene–polystyrene triblock copolymer, was incorporated into the matrix to enhance its toughness. The cured thermoset matrix showed different morphology when the elastomer was added to the B‐staged prepolymer or when the elastomer was B‐staged with the DVS‐bisBCB monomer. Small and uniformly distributed elastomer domains were detected by transmission electron micrographs (TEM) in the former case, but TEM did not detect a separate domain in the latter case. A high percentage of the polystyrene–polybutadiene–polystyrene triblock copolymer could be incorporated into the DVS‐bisBCB thermoset matrix by B‐staging the triblock copolymer with the BCB monomer. The elastomer increased the fracture toughness of DVS‐bisBCB polymer as indicated by enhanced elongation at break and increased K1c values obtained by the modified edge‐lift‐off test. Elastomer modified DVS‐bisBCB maintained excellent electrical properties, high T_g and good thermal stability, but showed higher coefficient of linear thermal expansion values. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1591–1599, 2006     

COPU／PMMA AB交联聚合物的性能

AB交联聚合物(ABCP)是由聚合物A链与化学组成不同的聚合物B链交联构成。它的网络结构不同于IPN。IPN是由两个独立的网络构成,而在ABCP中仅存在一个聚合物网络。目前人们对它远不及对IPN了解得多。 本文选用蓖麻油为原料,与甲基丙烯酸甲酯共聚,合成了一种ABCP。研究了它的力学性能,转变与松弛,相容性及形态结构与组成及交联密度的关系。     

A facile and controllable synthesis of dual‐crosslinked elastomers based on linear bifunctional polydimethylsiloxane oligomers

Dual‐crosslinked supramolecular elastomers with the hybrid network consisting of hydrogen bonds and covalent bonds combine the reversibility of hydrogen bond and mechanical properties of covalent crosslinking network. In this article, isocyanate mixture is used as curing agent to prepare dual‐crosslinked elastomer based on bifunctional polydimethylsiloxane under mild condition. This method can effectively build up a hybrid network with the designed structure. A series of elastomers with same hydrogen bond density and variable covalent crosslinking degree are obtained. Swelling measurements and ¹H‐NMR spectra confirm the feasibility and controllability of curing method, the increasing of bifunctional isocyanate give rise to higher covalent crosslinking degree, improving the solvent resistance. The studies on viscoelastic property show that the introduction of an irreversible covalent crosslinking network stabilize the hybrid network, restrain the chain movement. The mechanical and self‐healing property studies reveal that the covalent crosslink significantly reinforce the whole network, while the reparable strength seems to mainly depend on the hydrogen bond density. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3760–3768     

Modification of a thermoplastic elastomer gel through the addition of an endblock‐selective homopolymer

Addition of a midblock‐selective oil to an ABA triblock copolymer with a rubbery B‐midblock and thermoplastic A‐endblocks yields a thermoplastic elastomer gel (TPEG) if the oil constitutes the majority blend constituent and a physically crosslinked network, responsible for solid‐like mechanical properties, is retained. These blends typically exhibit a micellar morphology in which the micellar cores are composed of the oil‐incompatible A‐endblocks. Since the micelles serve as crosslink sites, the properties of TPEGs depend on (i) the intrinsic characteristics of the solid‐state endblocks, and (ii) the degree to which the micelles interact through bridged and looped midblocks. In this work, a poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] triblock copolymer and an aliphatic oil are used to prepare TPEGs into which poly(2,6‐dimethylphenylene oxide) (PPO), a styrene‐compatible homopolymer, is added. The morphologies and bulk properties of these ternary systems are examined by electron microscopy, viscometry, and dynamic rheology. A slight increase in the PPO content in these TPEGs promotes increases in micelle size, confirming that the PPO primarily resides within the micelles, and disordering temperature, signified by an abrupt change in rheological properties. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1863–1872, 1999     

Phase behavior,crystallization, and morphology in thermosetting blends of a biodegradable poly(ethylene glycol)‐type epoxy resin and poly(ϵ‐caprolactone)

Thermosetting blends of a biodegradable poly(ethylene glycol)‐type epoxy resin (PEG‐ER) and poly(?‐caprolactone) (PCL) were prepared via an in situ curing reaction of poly(ethylene glycol) diglycidyl ether (PEGDGE) and maleic anhydride (MAH) in the presence of PCL. The miscibility, phase behavior, crystallization, and morphology of these blends were investigated. The uncured PCL/PEGDGE blends were miscible, mainly because of the entropic contribution, as the molecular weight of PEGDGE was very low. The crystallization and melting behavior of both PCL and the poly(ethylene glycol) (PEG) segment of PEGDGE were less affected in the uncured PCL/PEGDGE blends because of the very close glass‐transition temperatures of PCL and PEGDGE. However, the cured PCL/PEG‐ER blends were immiscible and exhibited two separate glass transitions, as revealed by differential scanning calorimetry and dynamic mechanical analysis. There existed two phases in the cured PCL/PEG‐ER blends, that is, a PCL‐rich phase and a PEG‐ER crosslinked phase composed of an MAH‐cured PEGDGE network. The crystallization of PCL was slightly enhanced in the cured blends because of the phase‐separated nature; meanwhile, the PEG segment was highly restricted in the crosslinked network and was noncrystallizable in the cured blends. The phase structure and morphology of the cured PCL/PEG‐ER blends were examined with scanning electron microscopy; a variety of phase morphologies were observed that depended on the blend composition. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2833–2843, 2004     

CAMDA扩链聚氨酯脲的硬段对形态与性能的影响

由红外光谱、核磁共振及质谱分析证实了所合成的3-氯-3’-甲氧基-4,4’-二氨基二苯基甲烷(CAMDA)具有预期的化学结构.用RIM方法制成的CAMDA基聚氨酯脲(PUU)性能接近于DETDA扩链的PUU.用快速手工浇注法制备了一系列由CAMDA扩链的不同硬段含量的PUU样品.采用DSC、SEM观察了硬段含量由10％增加到45％PUU形态的变化,并测量了力学性能.实验结果表明:随着硬段含量增加,PUU的形态由平行间隔的软、硬链段富集区经相互穿叉的软、硬段富集区,进一步聚集成硬链段富集球状超级结构,强度亦相应提高.     

Preparation and characterization of waterborne poly(urethane urea) with well‐defined hard segments

A series of polyester‐based poly(urethane urea) (PUU) aqueous dispersions with well‐defined hard segments were prepared from polyester polyol, 4,4′‐diphenylmethane diisocyanate, dimethylolpropionic acid, 1,4‐butanediol, isophorone diisocyanate, and ethylenediamine. These anionic‐type aqueous dispersions had good dispersity in water and were stable at the ambient temperature for more than 1 year. For these aqueous dispersions, the particle size decreased as the hard‐segment content increased, and the polydispersity index was very narrow (<1.10). Films prepared with the PUU aqueous dispersions exhibited excellent waterproof performance: the amount of water absorption was as low as 5.0 wt %, and the contact angle of water on the surface of this kind of film was as high as 103° (this led to a hydrophobic surface). The water‐resistant property of these waterborne PUU films could be well correlated with some crystallites and ordered structures of the well‐defined hard segments formed by hydrogen bonding between the urethane/urethane groups and urethane/ester groups, as well as the degree of microphase separation between the hard and soft segments in the PUU systems. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 2606–2614, 2005     

Preparation and characterization of N‐methyl‐substituted polyurethane

We prepared N‐methyl‐substituted polyurethanes with different substitution degrees from sodium hydride, methyl p‐toluene sulfonate, and polyether–polyurethane containing poly(oxytetramethylene) glycol, 4,4′‐diphenylmethane diisocyanate, and 1,4‐butanediol. The chemical structures were characterized with Fourier transform infrared and ¹H NMR. To investigate the effects of the N‐substitution degree on the morphology, thermal stability, and mechanical properties, we used differential scanning calorimetry, thermogravimetric analysis, and a universal testing machine. As the substitution degree increased, the new free (1708 cm^?1) and bonded (1650 cm^?1) carbonyl peaks increased. There was no bonded carbonyl peak in fully substituted polyurethane because the urethane groups had no hydrogen. At a small substitution degree, we observed a slight increase in the glass‐transition temperature and decrease in the endotherms of soft‐segment and hard‐segment domains due to the decrease in the hard‐segment domain and the increase in the urethane groups in the soft‐segment domain. The hard‐segment domain decreased and then disappeared as the N‐methyl substitution degree increased. These changes in the morphology resulted (1) in decreased modulus and tensile strength for the films because of the decrease in physical crosslinking points and (2) improved thermal stability as the substitution degree increased. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 4077–4083, 2002     

Influence of varying hard segments on the properties of chemically crosslinked moisture‐cured polyurethane‐urea

Polyurethane prepolymers are widely used in the reactive hot melt adhesives and moisture‐cured coatings. The chemically crosslinked moisture‐cured formulation based on PEG‐1000 and isophorone diisocyanate was prepared with NCO/OH ratio of 1.6:1.0. Trimethylol propane was used as a crosslinking agent. The excess isocyanate of the prepolymer was chain extended in the ratio of 2:1 (NCO/OH) with different aliphatic diols, and 4:1 with different aromatic diamines. The polymer network maturation during moisture cure was followed by dynamic mechanical thermal analyzer (DMTA) instrument. The thermal and dynamic mechanical properties of the crosslinked polymers were evaluated using thermogravimetric analysis, differential scanning calorimetric analysis and DMTA. Surface properties were evaluated through angle‐resolved X‐ray photoelectron spectroscopy. The present article discusses the physical properties of moisture‐cured polyurethane‐urea (MCPU) containing chemical crosslinks in the hard segment. The complete moisture‐cured polymers showed amorous results toward room temperature modulus, tensile strength, hardness, thermal stability, and transparency. The surface properties showed the enrichment of soft segments. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 102–118, 2006     

Viscoelastic characteristics of UV polymerized poly(ethylene glycol) diacrylate networks with varying extents of crosslinking

The viscoelastic relaxation characteristics of ultraviolet crosslinked networks based on poly(ethylene glycol) diacrylate [PEGDA] have been investigated by dynamic mechanical methods. Effective crosslink density in the networks was varied via the use of PEGDA prepolymers of different molecular weight, or by the introduction of controlled amounts of water in the reaction mixture. In all cases examined, fully amorphous networks were obtained. Time–temperature superposition was applied to obtain master curves of storage modulus versus frequency across the glass transition, and these could be satisfactorily described using the Kohlrausch–Williams–Watts relaxation function. The glass transition temperature (T_g), relaxation breadth, and fragility of the segmental relaxation were correlated with the effective crosslink density obtained in the networks. Gas permeation measurements on the PEGDA/water networks indicated only a very modest variation in gas transport properties, despite the sizeable variation in apparent crosslink density achieved in these materials. This result suggests that the controlling structural factor for gas transport in the networks is not simply crosslink density, and that attempts to correlate gas transport to network structure must necessarily consider the broader relationships between crosslink density, segmental mobility, and fractional free volume. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2058–2070, 2006     

Local deformation in photo‐crosslinked polymer blends monitored by Mach‐Zehnder interferometry

Local deformation of a polymer mixture crosslinked by irradiation with ultraviolet light was in situ monitored by using a Mach‐Zehnder interferometer. In combination with the refractive index data obtained from independent measurements, the deformation in the nanometer scales of the crosslinked blends was calculated by using the difference in optical path length of the blend measured before and after irradiation. Upon varying the crosslink density of the blend by changing the light intensity, it was found that the local deformation well correlates with the crosslink density obtained from the reaction kinetics experiments. Furthermore, the strain relaxation of the blends was also monitored in situ and analyzed after irradiation over different time intervals. The results obtained in this study reveal the possibility of monitoring the nanometer‐scale deformation in polymers during radiation curing. These data also provide important information on the correlations between the irradiation‐induced elastic strain and the resulting morphology of reacting polymer blends. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2898–2913, 2005     

Actuation design for high‐performance shape memory polyurethanes

A series of shape memory polyurethanes were synthesized from poly(tetramethylene glycol), 4,4‐methylene diphenyl diisocyanate, and 1,3‐butanediol. The prepolymers with different molecular weights (M_c) were capped with 2‐hydroxyl ethylacrylate or 3‐aminopropyltriethoxysilane (APTES) and crosslinked by UV curing or a sol–gel reaction. Variations of the crosslinker functionality (f), subchain density (N), and hard segment content (HSC) produced systematic variations of the glass transition temperature (6–45 °C), accompanied by changes in the mechanical, dynamic mechanical and shape memory properties. More than 95% of shape fixity and 98% of shape recovery up to the fourth cycles were obtained with APTES crosslinked 3000M_c with 30% of HSC. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013 , 51, 1473–1479     

Synthesis,structure, and properties of polyimide and polyurethane‐urea‐imide copolymers

Several, novel polyimide–polyurethane‐urea‐imide (PI‐PUI) copolymers with different polyimide (PI) contents were prepared by an in situ interpenetrating reaction between polyurethane‐urea‐imide (PUI) precursor and poly(amide acid). Changing the ratio of the PUI precursor and poly(amide acid) resulted in a change of the properties of the PI‐PUI copolymers from plastic to elastomer. Fourier transform infrared spectra revealed the characteristic absorption bands of PI‐PUI copolymers; differential scanning calorimetry (DSC) analyses revealed that the glass‐transition temperature of the soft‐segment‐rich phase decreased as the PI content increased in PI‐PUIs, meaning that the soft segments (i.e., PEG) were more incompatible and had better crystallizability with a high‐PI‐segment content in PI‐PUI. Wide‐angle X‐ray diffraction curves exhibited more ordered structure within the disordered PI‐PUI copolymer's state with an increasing PI content, which further agreed with the DSC results. Scanning electron micrographs clearly showed that the molecular chains in PI‐PUI with a high‐PI‐content packed, ordered lamellar structure. Thermogravimetric curves indicated that the heat resistance of PI‐PUI was better than pure PUI. The introduction of the PI component into PUI by an in situ interpenetrating reaction method is an effective way to improve the thermal stability and solvent resistance of PUI. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 216–225, 2004     

Thermal expansion coefficient and bulk modulus of polyethylene closed‐cell foams

A regular Kelvin foam model was used to predict the linear thermal expansion coefficient and bulk modulus of crosslinked, closed‐cell, low‐density polyethylene (LDPE) foams from the polymer and gas properties. The materials used for the experimental measurements were crosslinked, had a uniform cell size, and were nearly isotropic. Young's modulus of biaxially oriented polyethylene was used for modeling the cell faces. The model underestimated the foam linear thermal expansion coefficient because it assumed that the cell faces were flat. However, scanning electron microscopy showed that some cell faces were crumpled as a result of foam processing. The measured bulk modulus, which was considerably smaller than the theoretical value, was used to estimate the linear thermal expansion coefficient of the LDPE foams. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3741–3749, 2004