Synthesis and characterization of poly(arylene ether sulfone)s with trans‐1,4‐cyclohexylene ring containing ester linkages

trans‐1,4‐Cyclohexylene ring containing acid chloride monomers were incorporated into poly(arylene ether sulfone) (PAES) backbones to study their effect on mechanical and thermal properties. The trans‐1,4‐cyclohexylene ring containing acid chloride monomers were synthesized and characterized by NMR and high‐resolution mass spectrum. trans‐1,4‐Cyclohexylene containing PAESs were synthesized from the acid chloride monomers and hydroxyl terminated polysulfone oligomers with a pseudo‐interfacial method and a solution method. These PAESs, with trans‐1,4‐cyclohexylene ring containing ester linkages, were fully characterized by NMR, thermogravimetric analysis, differential scanning calorimetry (DSC), size exclusion chromatography, and dynamic mechanical analysis (DMA). The tensile properties were also evaluated. The polymers made with the pseudo‐interfacial method had relatively low molecular weights when compared to the solution method where much higher molecular weight polymers were obtained. Crystallinity was promoted in the low molecular weight biphenol‐based PAES samples with the pseudo‐interfacial method. The crystallinity was confirmed by both the DSC and the wide angle X‐ray diffraction results. The tensile test results of the high molecular weight polymers suggested that incorporation of the trans‐1,4‐cyclohexylene ring containing linkage slightly improved the ultimate elongations while maintaining the Young's moduli. The trans‐1,4‐cyclohexylene ring containing PAESs also showed higher sub‐T_g relaxations in DMA when compared with their terephthaloyl containing analog. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Hydrolytic stability and high Tg of polyimides derived from the novel 4,9‐bis[4‐(3,4‐dicarboxyphenoxy)phenyl]‐diamantane dianhydride

This work reports the synthesis and characterization of diamantane‐based polyimides obtained from 4,9‐bis[4(3,4‐dicarboxyphenoxy)phenyl]diamantane dianhydride and various aromatic diamines. Interestingly, the diamantane‐based polyimides were very stable to hydrolysis. This novel polyimide exhibits a low dielectric constant (2.65–2.77), low moisture absorption (<0.67%), good solubility, high T_g and unusually high thermal stability. Dynamic mechanical analysis (DMA) reveals that the diamantane‐based polyimides have high T_g ranging from 281 to 379 °C. The high‐temperature β₁ subglass transition around 285 °C was observed in polyimide 6a derived from 2,2′‐bis(trifluoromethyl)benzidine. This class of novel diamantane‐based polyimide is very promising for electronic applications, because of its good mechanical properties, good thermal stability, low dielectric constant, excellent hydrolytic resistance, and low moisture absorption. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1673–1684, 2009     

Synthesis and properties of novel phosphorus‐containing thermotropic liquid crystalline copoly(ester imide)s

A series of novel phosphorus‐containing polyesterimides were prepared from diols—a mixture of a new aromatic phosphorus‐containing bisphenol, namely 1,4‐bis[N‐(4‐hydroxyphenyl)phthalimidyl‐5‐carboxylate]‐2‐(6‐oxido‐6H‐dibenz<c,e><1,2>oxaphosphorin‐6‐yl)‐naphtalene, with aliphatic diols such as 1,3‐propanediol, 1,4‐butanediol, 1,5‐pentanediol, 1,6‐hexanediol, and 1,12‐dodecanediol—and an aromatic diacid chloride containing two preformed ester groups, namely terephthaloyl‐bis‐(4‐oxibenzoyl‐chloride), via high‐temperature polycondensation in o‐dichlorobenzene. The structures of monomers and polymers were verified by means of Fourier transform infrared (FTIR) spectroscopy and ¹H NMR spectroscopy. The molar ratio of aromatic bisphenol to aliphatic diol was varied to generate a series of copolyesterimides with tailored physicochemical properties, structure–properties relationships being established. The effect of the phosphorus content on the thermal properties and the flame retardancy was evaluated by means of thermogravimetric analysis (TGA), TGA–FTIR, and scanning electron microscopy. The polymers were stable up to 340 °C showing a 5% weight loss in the range of 340–395 °C and a 10% weight loss in the range of 370–415 °C. The char yields at 700 °C were in the range of 13.6–38% increasing with the content of phosphorus‐containing bisphenol. The effect of the aliphatic content on the liquid crystalline behavior was investigated by polarized light microscopy, differential scanning calorimetry, and X‐ray diffraction. The transition temperatures from crystal to liquid crystalline melt were in the range of 209–308 °C. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and characterization of organosoluble ditrifluoromethylated aromatic polyimides

Two novel diamine monomers, 1,4‐bis (4‐aminophenoxy)‐2‐[(3′,5′‐ditrifluoromethyl)phenyl]benzene and 1,4‐bis [2′‐cyano‐3′(4″‐amino phenoxy)phenoxy]‐2‐[(3′,5′‐ditrifluoromethyl)phenyl] benzene, were synthesized from (3,5‐ditrifluoromethyl)phenylhydroquinone. A series of ditrifluoromethylated aromatic polyimides derived from the diamines were prepared through a typical two‐step polymerization method. These polyimides had a high thermal stability, and the temperatures at 10% weight loss were above 507 °C in nitrogen. Most of the polymers showed good solubility in anhydrated 1‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide, chloroform, and tetrahydrofuran at room temperature. All the polymers formed transparent, strong, and flexible films with tensile strengths of 63.6–95.8 MPa, elongations at break of 5–10%, and Young's moduli of 2.38–2.96 GPa. The dielectric constants estimated from the average refractive indices are 2.69–2.89. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3018–3029, 2005     

Polycarbazoles via C?N coupling reactions of phthaloyl bis‐9H‐carbazoles with activated difluorides

1,3‐Phthaloyl bis‐9H‐carbazole (MPC) and 1,4‐phthaloyl bis‐9H‐carbazole (PPC) were synthesized by a Friedel‐Crafts reaction of carbazole with terephthaloyl chloride or isophthaloyl chloride. Homopolymers were obtained by a C? N coupling reaction with activated difluorides and copolymers were synthesized with 4,4′‐biphenol as a comonomer by a nucleophilic substitution reaction between these NH‐ and OH‐containing monomers and the activated difluoro monomers. The inherent viscosities of the polymers ranged from 0.35 to 1.03 dL/g. These polymers exhibited glass‐transition temperatures greater than 238 °C with the PPC‐containing homopolymer showing the highest value, 326.4 °C. The thermal stabilities indicated no significant weight loss below 450 °C and the temperatures of 5% weight loss ranged from 514.0 to 546.3 °C. The polymers showed reasonable solubility in organic solvents such as DMAC, DMSO, and NMP. UV absorption and fluorescence emission properties are presented. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 4326–4331, 2009     

Development of functional polymers with cyclic ether moieties. I. Synthesis and properties of polyesters with dioxane moiety in the main chain

A series of novel polyesters containing dioxane moieties in their main chains were synthesized by the bulk polycondensation of trans‐2,5‐bis‐(hydroxy‐ methyl)‐1,4‐dioxane with various aliphatic dicarboxylic acid chlorides. The obtained polyesters, analyzed by differential thermal analysis, possessed crystallinity, the melting point of which exhibited a weak odd–even effect on the methylene unit number and a small decreasing trend with an increase in the methylene unit number. These properties were compared with those of similar polyesters bearing cyclohexane moieties, and it was found that the rigidity of the dioxane moiety plays an important role in enhancing the effective packing of the corresponding polymers. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2536–2542, 2000     

Thermal analysis of 1,4‐di[n′‐(quinolyl)]buta‐1,3‐diynes,structure, and topo‐oligomerization: Polymerization of 3‐ethynylquinoline with the triethyl aluminum/vanadium 2,4‐pentanedionate catalyst system

Conjugated 1,4‐bis(n′‐quinolyl)‐1,3‐butadiynes were obtained through the oxidative dimerization of the corresponding n′‐ethynylquinolines catalyzed by cuprous chloride. Differential scanning calorimetry analysis of the 1,4‐bis[n′‐(quinolyl)]buta‐1,3‐diyne molecules produced evidence of a syn–anti rotational equilibrium around the 1,3‐diyne axis and an irreversible transformation into a thermopolymer. The topo‐oligomerization of 1,4‐bis[3′‐(quinolyl)]buta‐1,3‐diyne, which took place by irradiation with sunlight, was investigated with matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry. Accurate X‐ray molecular structure and refinement analysis of 1,4‐bis[3′‐(quinolyl)]buta‐1,3‐diyne was conducted. The molecular crystalline packing consisted of parallel arrays of two groups of centrosymmetric molecules (antirotamer) in a herringbone assemblage in the solid state. The polymerization of 3‐ethynylquinoline was carried out with the AlEt₃/V(acac)₃ system to produce a mixture of 1,2,4‐ and 1,3,5‐tris(3′‐quinolyl)benzene cyclotrimers and a trans–cisoid polyene structure. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 6031–6040, 2004     

Hydrogen‐bonded thermotropic liquid‐crystalline polyester–amides from bis(hydroxy alkamido)aranes: Synthesis and properties

Hydrogen‐bonded aromatic–aliphatic polyester–amides (PEAs) were prepared by solution/melt polycondensation of aromatic–aliphatic amidodiols 1,4‐bis(4‐hydroxybutyramide)benzene (BHBB), 1,4‐bis(5‐hydroxy pentamide)benzene, 1,4‐bis(6‐hydroxyhexamide)benzene, 1,4‐bis(4‐hydroxybutyramidexylene), 1,4‐bis(5‐hydroxypentamidexylene, 1,4‐bis(4‐hydroxybutyramide)benzene, and 1,4‐bis(6‐hydroxyhexamidexylene) with terephthaloyl chloride/dimethyl terephthalate. Aromatic–aliphatic amido diols were prepared by the aminolysis of γ‐butyrolactone, δ‐valerolactone, and ?‐caprolactone with aromatic diamines such as paraphenylene diamine and paraxylene diamine. The monomers and polymers were characterized by chemical analysis (hydroxyl value and elemental analysis), Fourier transform infrared spectroscopy, ¹H NMR, and ¹³C NMR. The thermal‐ and phase‐transition behaviors of the polymers were investigated by differential scanning calorimetry in combination with hot‐stage optical microscopy. Crystallinity of polymers was examined with wide‐angle X‐ray diffraction. The polymers exhibited liquid crystallinity with layered structures formed by self‐organization of the hetero intermolecular hydrogen‐bonded networks indicating smectic phases except for PEAs prepared from BHBB. The hydrogen atom of the phenyl‐substituent group forces the neighboring carbonyl groups out of plane of the rings preventing formation of layered structures in the case of BHBB. The PEAs retained intermolecular hydrogen bonding even in the mesomorphic state, and variations in the hydrogen‐bonded lamellae/micelles might be responsible for the variations from one smectic to another texture. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 335–346, 2003     

Synthesis and properties of conjugated polymers containing 3,9‐carbazolylene and silylenevinylene moieties in the main chain

Novel conjugated polymers containing 3,9‐carbazolylene and silylenevinylene moieties were synthesized by the hydrosilylation polymerization of 1,4‐bis(3‐ethynyl‐9‐carbazolyl)benzene ( 1 ) with various bis(hydrosilane)s or dihydrosilanes using a rhodium catalyst. Polymers with weight‐average molecular weights ranging from 5400 to 20,000 were obtained in 55–97% yields by the polyaddition with a rhodium catalyst in toluene at 25 °C for 24 h. All the polymers were soluble in CHCl₃ and THF, and had predominantly trans‐structures. The polymers exhibited λ_max at a longer wavelength region than 1 , and emitted fluorescence in 14–50% quantumn yields. The polymers were oxidized and reduced in the region of 0.4–1.6 V, and thermally stable up to 200 °C under air. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1815–1821, 2010     

Synthesis of polyesters by the polyaddition of bis(oxetane)s with active di(ester)s

The polyaddition of bis(oxetane)s 1,4‐bis[(3‐ethyl‐3‐oxetanylmethoxymethyl)]benzene (BEOB), 4,4′‐bis[(3‐ethyl‐3‐oxetanyl)methoxy]benzene (4,4′‐BEOBP), 1,4‐bis[(3‐ethy‐3‐oxetanyl)methoxy] ‐benzene (1,4‐BEOMB), 1,2‐bis[(3‐ethyl‐3‐oxetanyl)methoxy]benzene (1,2‐BEOMB), 4,4‐bis[(3‐ethyl‐3‐oxetanyl)methoxy]biphenyl (4,4′‐BEOMB), 3,3′,5,5′‐tetramethyl‐[4,4′‐bis(3‐ethyl‐3‐oxetanyl)methoxy]biphenyl (TM‐BEOBP) with active diesters di‐s‐phenylthioterephthalate (PTTP), di‐s‐phenylthioisoterephthalate (PTIP), 4,4′‐di(p‐nitrophenyl)terephthalate (NPTP), 4,4′‐di(p‐nitrophenyl)isoterephthalate (NPIP) were carried out in the presence of tetraphenylphosphonium chloride (TPPC) as a catalyst in NMP for 24 h, affording corresponding polyesters with M_n's in the range 2200–18,200 in 41–98% yields. The obtained polymers would soluble in common organic solvents and had high thermal stabilities. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1528–1536, 2004     

Influence of stereochemistry on the thermal properties of partially cycloaliphatic polyamides

The effects of the partial substitution of 1,4‐disubstituted cyclohexane monomers for linear aliphatic monomers in polyamides are discussed. More specifically, the relation between the stereochemistry of the cycloaliphatic residues and the thermal properties [melting temperature (T_m) and crystallization temperature (T_cr)] was investigated. For this purpose, two different types of copolyamides were synthesized: in polyamides 12.6, the adipic acid residues were partially replaced by cis/trans‐1,4‐cyclohexanedicarboxylic acid (1,4‐CHDA), whereas in polyamides 4.14, the 1,4‐diaminobutane residues were partially substituted with cis/trans‐1,4‐diaminocyclohexane (1,4‐DACH). For both systems, increasing the degree of substitution of cycloaliphatic residues for linear aliphatic residues resulted in a rise of both T_m and T_cr. This points to the isomorphous crystallization of the linear and cycloaliphatic residues. In contrast to the use of 1,4‐DACH as a comonomer, 1,4‐CHDA residues showed isomerization upon thermal treatment of the polyamides. This isomerization of the cyclohexane residues influenced the thermal properties of the copolyamides. The use of a nonisomerizing cis–trans mixture of 1,4‐DACH exhibited the large influence of the stereochemistry of the cycloaliphatic residues on the T_m of the copolyamides. For both the 1,4‐CHDA‐ and 1,4‐DACH‐based copolyamides, differential scanning calorimetry analysis revealed that recrystallization occurs during melting. This exothermal effect becomes less pronounced with an increasing content of rigid cycloaliphatic residues. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1962–1971, 2002     

Synthesis and characterization of fluoropolymers by the polyaddition of bis(epoxide)s with dicarboxylic acids and diols

The synthesis and characterization of the fluoropolymers poly 1a – 1d and poly 2a – 2d with pendant hydroxyl groups were examined. The polyaddition of bis(epoxide)s [2,2′‐bis(4‐glycidyletherphenyl)hexafluoropropane and bisphenol A diglycidyl ether] with dicarboxylic acids (tetrafluoroterephthalic acid and terephthalic acid) and diols [2,2′‐bis(4‐hydroxyphenyl)hexafluoropropane, 2,2′,3,3′,5,5′,6,6′‐octafluoro‐4,4′‐biphenol, 1,4‐bis(hexafluorohydroxyisopropyl)benzene, and 1,3‐bis(hexafluorohydroxyisopropyl)benzene] was carried out at 50–100 °C for 6–48 h in the presence of quaternary onium salts (tetrabutylammonium bromide, tetrabutylammonium chloride, tetrabutylphosphonium bromide, and tetrabutylphosphonium chloride; 2.5 mol %) as catalysts in dimethyl sulfoxide, N‐methylpyrrolidone, dimethylformamide, dimethylacetamide, dioxane, diglyme, o‐dichlorobenzene, chlorobenzene, and toluene to afford the corresponding polymers, poly 1a – 1d and poly 2a – 2d , with number‐average molecular weights of 11,000–59,400 in 45–97% yields. The solubility of the obtained polymers was good, and their thermal stability might be assumed from their structures. A linear relationship was observed between the contents of the fluorine atoms and the refractive indices. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 1395–1404, 2002     

Synthesis of conjugated polymers with azobenzene moieties in the main chain

Poly(phenylenevinylene)‐based conjugated polymers with azobenzene groups in the main chains were prepared by the Pd‐catalyzed coupling polymerization of divinylarenes with dihaloarenes. The Pd‐catalyzed coupling polymerization of 4,4′‐divinylazobenzene with dihaloarenes such as 1,3‐dibromobenzene, 1,4‐dibromo‐2,5‐dihexylbenzene, 4,4′‐dibromoazobenzene, and 4,4′‐diiodoazobenzene resulted in polymers with poor solubility. In contrast, soluble polymers containing azobenzene moieties in the main chains were attainable from divinylbenzenes with 4,4′‐dihaloazobenzenes if either or both of the monomers possessed hexyl groups on the aromatic rings. The number‐average molecular weight of the polymer exceeded 10,000 under optimized conditions, and the polymer showed a remarkably redshifted absorption in the visible region (456 nm). ¹H NMR and IR spectra supported that the polymers having only trans‐geometry for the double bonds. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1057–1063, 2000     

The influence of comonomer (2‐hydroxyethyl acrylate) and keto group on photocrosslinking property of arylidene polymers

Two types of arylidene compounds were synthesized by reacting p‐hydroxybenzaldehyde with acetone [1,5‐bis(4‐hydroxyphenyl)penta‐1,4‐dien‐3‐one] (PBHP) and cyclohexanone [2,6‐bis(4‐hydroxybenzylidene)cyclohexanone] (HBC). 1,4‐Pentadien‐3‐one‐1‐p‐hydroxyphenyl‐5‐p‐phenyl methacrylate (PHPPMA) and 4‐{[‐3‐(4‐hydroxybenzylidene)‐2‐oxocyclohexylidene]methyl}phenyl acrylate (HBA) were prepared by reacting PBHP and HBC with methacryloyl chloride and acryloyl chloride in the presence of triethylamine, respectively. Copolymerization of different feed compositions of PHPPMA and HBA with 2‐hydroxyethyl acrylate (HEA) was carried out using a free‐radical solution polymerization technique in ethyl methyl ketone (MEK) using benzoyl peroxide (BPO). All the monomer and polymers were characterized by IR and NMR (¹H/¹³C) spectroscopic techniques. The reactivity ratio of the monomers were obtained using Fineman–Ross (FR), Kelen–Tudos (KT), and extended Kelen–Tudos (exKT) methods. The photocrosslinking properties of the polymers were done using a UV absorption spectroscopy technique. Homopolymers of both the arylidene polymers shows similar trend towards the rate of photocrosslinking. The rate of photocrosslinking was enhanced when the cyclohexanone based arylidene monomer was copolymerized with HEA. Thermal stability and molecular weights (M_w and M_n) of the polymers were determined. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3433–3444, 2004     

Preparative Synthesis of Vinyl Diamondoids

We describe a convenient four-step preparation of 1- vinyl adamantane, 1- vinyl diamantane, and 4,9-divinyl diamantane from the respective diamondoid acetic acids in 50–80% isolated yields involving esterification, reduction, and hydrobromination/dehydrobromination.

Supplemental materials are available for this article. Go to the publisher's online edition of Synthetic Communications® to view the free supplemental file.     

High performance benzoxazine monomers and polymers containing furan groups

Furan‐containing benzoxazine monomers, 3‐furfuryl‐3,4‐dihydro‐2H‐1,3‐benzoxazine (P‐FBz) and bis(3‐furfuryl‐3,4‐dihydro‐2H‐1,3‐benzoxazinyl)isopropane (BPA‐FBz), were prepared using furfurylamine as a raw material. The chemical structures of P‐FBz and BPA‐FBz were characterized with FTIR, ¹H NMR, elemental analysis, and mass spectrometry. Formation of furfurylamine Mannich bridge networks in the polymerizations of P‐FBz and BPA‐FBz increased the cross‐linking densities and thermal stability of the resulting polybenzoxazines. P‐FBz‐ and BPA‐FBz‐based polymers also exhibited high glass transition temperatures above 300 °C, high char yields, and low flammability with limited oxygen index values of 31. The dielectric (D_k = 3.21–3.39) and mechanical properties (high storage modulus of 3.0–3.9 GPa and low coefficient of thermal expansion of 37.7–45.4 ppm) of the P‐FBz‐ and BPA‐FBz‐based polymers were superior or comparable to other polybenzoxazines. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5267–5282, 2005     

Synthesis and properties of a novel high temperature pyridine‐containing phthalonitrile polymer

A novel pyridine‐containing aromatic phthalonitrile monomer, 2,6‐bis[4‐(3,4‐dicyanophenoxy)benzoyl]pyridine (BCBP) was synthesized from the nitro displacement of 4‐nitrophthalonitrile by the phenoxide of 2,6‐bis (4‐hydroxybenzoyl)pyridine (BHBP). 4‐(Aminophenoxy) phthalonitrile (APPH) was selected to promote the curing reaction, and the curing behavior has been investigated by differential scanning calorimetric (DSC), suggesting a wide processing window about 64 °C. Different curing additive concentrations resulted in polymers with different crosslinking degrees and subsequently influenced the performance of resins. The resulting BCBP polymer exhibited high glass transition temperatures exceeding 400 °C, outstanding thermo‐oxidative stability with weight retention of 95% at 530 °C, indicating a significant improvement in thermal properties endowed by pyridine units. Additionally, it also showed a lower overall water absorption after submersion in boiling water for 50 hours. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 3819–3825     

New liquid‐crystalline poly(ester amide)s: The role of nitro groups in the phase behavior

New hydrogen‐bonded liquid‐crystalline poly(ester amide)s (PEA)s were obtained from 1,4‐terephthaloyl[bis‐(3‐nitro‐N‐anthranilic acid)] (5) or 1,4‐terephthaloyl[bis‐(N‐anthranilic acid)] (6), with or without nitro groups, respectively, through the separate condensation of each with hydroquinone or dihydroxynaphthalene. The dicarboxylic monomers were synthesized from 2‐aminobenzoic acid. The phase behavior of the monomers and polymers were studied with differential scanning calorimetry, polarized light microscopy, and wide‐angle X‐ray diffraction methods. Monomer 5, containing nitro groups, exhibited a smectic liquid‐crystalline phase, whereas the texture of monomer 6 without nitro groups appeared to be nematic. The PEAs containing nitro groups exhibited polymorphism (smectic and nematic), whereas those without nitro groups exhibited only one phase transition (a nematic threaded texture). The changes occurring in the phase behavior of the polymers were explained by the introduction of nitro groups. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1289–1298, 2004     

Syntheses and electroluminescence properties of conjugated poly(p‐phenylene vinylene) derivatives bearing dendritic pendants

A series of new poly(p‐phenylene vinylene) derivatives with different dendritic pendants—poly{2‐[3′,5′‐bis(2″‐ethylhexyloxy)benzyloxy]‐1,4‐phenylenevinylene} (BE–PPV), poly{2‐[3′,5′‐bis(3″,7″‐dimethyl)octyloxy]‐1,4‐phenylenevinylene} (BD–PPV), poly(2‐{3′,5′‐bis[3″,5″‐bis(2?‐ethylhexyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene) (BBE–PPV), poly(2‐{3′,5′‐bis[3″,5″‐bis(3?,7?‐dimethyloctyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene) (BBD–PPV), and poly[(2‐{3′,5′‐bis[3″,5″‐bis(2?‐ethylhexyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene)‐co‐(2‐{3′,5′‐bis[3″,5″‐bis(3?,7?‐dimethyloctyloxy)benzyloxy]benzyloxy}‐1,4‐phenylenevinylene)] (BBE‐co‐BBD–PPV; 1:1)—were successfully synthesized according to the Gilch route. The structures and properties of the monomers and the resulting conjugated polymers were characterized with ¹H and ¹³C NMR, elemental analysis, gel permeation chromatography, thermogravimetric analysis, ultraviolet–visible absorption spectroscopy, photoluminescence, and electroluminescence spectroscopy. The obtained polymers possessed excellent solubility in common solvents and good thermal stability, with a 5% weight loss temperature of more than 328 °C. The weight‐average molecular weights and polydispersity indices of BE–PPV, BD–PPV, BBE–PPV, BBD–PPV, and BBE‐co‐BBD–PPV (1:1) were in the range of 1.33–2.28 × 10⁵ and 1.35–1.53, respectively. Double‐layer light‐emitting diodes (LEDs) with the configuration of indium tin oxide/polymer/tris(8‐hydroxyquinoline) aluminum/Mg:Ag/Ag devices were fabricated, and they emitted green‐yellow light. The turn‐on voltages of BE–PPV, BD–PPV, BBE–PPV, BBD–PPV, and BBE‐co‐BBD–PPV (1:1) were approximately 5.6, 5.9, 5.5, 5.2, and 4.8 V, respectively. The LED devices of BE–PPV and BD–PPV possessed the highest electroluminescent performance; they exhibited maximum luminance with about 860 cd/m² at 12.8 V and 651 cd/m² at 13 V, respectively. The maximum luminescence efficiency of BE–PPV and BD–PPV was in the range of 0.37–0.40 cd/A. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3126–3140, 2005     

Star‐shaped cyclopolymers: A new category of star polymer with rigid cyclized arms prepared by controlled cationic cyclopolymerization and subsequent microgel formation of divinyl ethers

The combination of living/controlled cationic cyclopolymerization and crosslinking polymerization of bifunctional vinyl ethers (divinyl ethers) was applied to the synthesis of core‐crosslinked star‐shaped polymers with rigid cyclized arms. Cyclopolymerization of 4,4‐bis(vinyloxymethyl)cyclohexene ( 1 ), a divinyl ether with a cyclohexene group, was investigated with the hydrogen chloride/zinc chloride (HCl/ZnCl₂) initiating system in toluene at 0 °C. The reaction proceeded quantitatively to give soluble poly( 1 )s in organic solvents. The content of the unreacted vinyl groups in the produced polymers was less than ～3 mol%, and therefore, the degree of cyclization of the polymers was determined to be ～97%. The number‐average molecular weight (M_n) of the polymers increased in direct proportion to monomer conversion and further increased on addition of a fresh monomer feed to the almost completely polymerized reaction mixture, indicating that living cyclopolymerization of 1 occurred. The chain linking reactions among the formed living cyclopolymers with 1,4‐bis(vinyloxy)cyclohexane ( 3 ) as a crosslinker in toluene at 0 °C produced core‐crosslinked star‐shaped cyclopoly( 1 )s [star‐poly( 1 )s] in high yield (100%). Dihydroxylation of the cyclohexene double bonds of star‐poly( 1 ) gave hydrophilic water‐soluble star‐shaped polymers with rigid arm structure [star‐poly( 1 )‐OH] with thermo‐responsive function in water. T_gs of star‐poly( 1 ) and star‐poly( 1 )‐OH were 135 °C and 216 °C, respectively; these values are very high as vinyl ether‐based star‐shaped polymers. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1094–1102