Dynamic mechanical properties of isotactic polypropylene/nitrile rubber blends: Effects of blend ratio,reactive compatibilization,and dynamic vulcanization

The effect of blend ratio and compatibilization on dynamic mechanical properties of PP/NBR blends was investigated at different temperatures. The storage modulus of the blend decreased with increase in rubber content and shows two T_g's indicating the incompatibility of the system. Various composite models have been used to predict the experimental viscoelastic data. The Takayanagi model fit well with the experimental values. The addition of phenolic modified polypropylene (Ph-PP) and maleic modified polypropylene (MA-PP) improved the storage modulus of the blend at lower temperatures. The enhancement in storage modulus was correlated with the change in domain size of dispersed NBR particles. The effect of dynamic vulcanization using sulfur, peroxide, and mixed system on viscoelastic behavior was also studied. Among these peroxide system shows the highest modulus. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2309–2327, 1997     

Crystallization behavior of dynamically cured polypropylene/epoxy blends

Dynamically cured polypropylene (PP)/epoxy blends compatibilized with maleic anhydride grafted PP were prepared by the curing of an epoxy resin during melt mixing with molten PP. The morphology and crystallization behavior of dynamically cured PP/epoxy blends were studied with scanning electron microscopy, differential scanning calorimetry, and polarized optical microscopy. Dynamically cured PP/epoxy blends, with the structure of epoxy particles finely dispersed in the PP matrix, were obtained, and the average diameter of the particles slightly increased with increasing epoxy resin content. In a study of the nonisothermal crystallization of PP and PP/epoxy blends, crystallization parameter analysis showed that epoxy particles could act as effective nucleating agents, accelerating the crystallization of the PP component in the PP/epoxy blends. The isothermal crystallization kinetics of PP and dynamically cured PP/epoxy blends were described by the Avrami equation. The results showed that the Avrami exponent of PP in the blends was higher than that of PP, and the crystallization rate was faster than that of PP. However, the crystallization rate decreased when the epoxy resin content was greater than 20 wt %. The crystallization thermodynamics of PP and dynamically cured PP/epoxy blends were studied according to the Hoffman theory. The chain folding energy for PP crystallization in dynamically cured PP/epoxy blends decreased with increasing epoxy resin content, and the minimum of the chain folding energy was observed at a 20 wt % epoxy resin content. The size of the PP spherulites in the blends was obviously smaller than that of PP. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1181–1191, 2004     

Melting behavior in blends of isotactic polypropylene and a liquid crystalline polymer

The influence of low contents of a liquid crystalline polymer on the crystallization and melting behavior of isotactic polypropylene (iPP) was investigated using electron and optical microscopy, differential scanning calorimetry, and X-ray diffraction. In pure iPP, the α modification was found, whereas for iPP/Vectra blends at Vectra concentration <5%, both α and β forms were observed. The amount of β phase varied from 0.23 to 0.16. Optical microscopy showed that Vectra was able to nucleate both α and β forms. Non-isothermal crystallization produces a material with a strong tendency for recrystallization of the α and β forms (αα′ and ββ′ recrystallization) leading to double endotherms for both crystalline forms in DSC thermograms. Melting thermograms after isothermal crystallization at low temperatures showed a similar behavior. At values of T_c > 119 °C for the α form and T_c > 125 °C for the β form, only one melting endotherm was observed because enough perfect crystals, not susceptible to recrystallization, were obtained. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1949–1959, 2004     

Impact‐specific essential work of fracture of maleic anhydride‐compatibilized polypropylene/elastomer blends and their composites

Charpy drop‐weight‐impact and essential work of fracture (EWF) characteristics of maleic anhydride (MA)‐compatibilized styrene–ethylene butylene–styrene (SEBS)/polypropylene (PP) blends and their composites reinforced with short glass fibers (SGFs) were investigated. MA was grafted to either SEBS copolymer (SEBS‐g‐MA) or PP (PP‐g‐MA). The mPP blend was prepared by the compounding of 95% PP and 5% PP‐g‐MA. Drop‐weight‐impact results revealed that the mPP specimen had an extremely low impact strength. The incorporation of SEBS or SEBS‐g‐MA elastomers into mPP improved its impact strength dramatically. Similarly, the addition of SEBS was beneficial for enhancing the impact strength of the SGF/SEBS/mPP and SGF/SEBS‐g‐MA/mPP hybrids. A scanning electron microscopy examination of the fractured surfaces of impact specimens revealed that the glass‐fiber surfaces of the SGF/SEBS/mPP and SGF/SEBS‐g‐MA/mPP hybrids were sheathed completely with deformed matrix material. This was due to strong interfacial bonding between the phase components of the hybrids associated with the MA addition. Impact EWF tests were carried out on single‐edge‐notched‐bending specimens at 3 m s^?1. The results showed that pure PP, mPP, and the composites only exhibited specific essential work. The nonessential work was absent in these specimens under a high‐impact‐rate loading condition. The addition of SEBS or SEBS‐g‐MA elastomer to mPP increased both the specific essential and nonessential work of fracture. This implied that elastomer particles contributed to the dissipation of energy at the fracture surface and in the outer plastic zone at a high impact speed of 3 m s^?1. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1881–1892, 2002     

Phase morphology development in PP/PA6 blends induced by a maleated thermoplastic elastomer

The effects of maleated thermoplastic elastomer (TPEg) on morphological development of polypropylene (PP)/polyamide 6 (PA6) blends with a fixed PA6 content (30 wt %) were investigated. For purpose of comparison, nonmaleated thermoplastic elastomer (TPE) was also added to the above binary blends. A comparative study of FTIR spectroscopy in above both ternary blends confirmed the formation of in situ graft copolymer in the PP/PA6/TPEg blend. Dynamic mechanical analysis (DMA) indicated that un‐like TPE, the incorporation of TPEg remarkably affected both intensity and position of loss peaks of blend components. Scanning electron microscopy (SEM) demonstrated that PP/PA6/TPE blends still exhibited poor interfacial adhesion between the dispersed phase and matrix. However, the use of TPEg induced a finer dispersion and promoted interfacial adhesion. Transmission electron microscopy (TEM) for PP/PA6/TPEg blends showed that a core‐shell structure consisting of PA6 particles encapsulated by an interlayer was formed in PP matrix. With the concentration of TPEg increasing, the dispersed core‐shell particles morphology was found to transform from discrete acorn‐type particles to agglomerate with increasing degree of encapsulation. The modified Harkin's equation was applied to illustrate the evolution of morphology with TPEg concentration. “Droplet‐sandwiched experiments” further confirmed the encapsulation morphology in PP/PA6/TPEg blends. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1050–1061, 2006     

Structure and mechanical properties of talc‐filled blends of polypropylene and styrenic block copolymers

The structure–property relationships of isotactic polypropylene (iPP)/styrenic block copolymer blends filled with talc were examined by optical and scanning electron microscopy, wide‐angle X‐ray diffraction, and tensile‐ and impact strength measurements. The composites were analyzed as a function of the poly(styrene‐b‐ethylene‐co‐propylene) diblock copolymer (SEP) and the poly(styrene‐b‐butadiene‐b‐styrene) triblock copolymer (SBS) content in the range from 0 to 20 vol % as elastomeric components and with 12 vol % of aminosilane surface‐treated talc as a filler. Talc crystals incorporated in the iPP matrix accommodated mostly plane‐parallel to the surface of the samples and strongly affected the crystallization process of the iPP matrix. The SBS block copolymer disoriented plane‐parallel talc crystals more significantly than the SEP block copolymer. The mechanical properties depended on the final phase morphology of the investigated iPP blends and composites and supermolecular structure of the iPP matrix because of the interactivity between their components. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1255–1264, 2004     

Toughness mechanism of polypropylene/elastomer/filler composites

The toughening mechanisms of polypropylene filled with elastomer and calcium carbonate (CaCO₃) particles were studied. Polypropylene/elastomer/CaCO₃ composites were prepared on a twin‐screw extruder with a particle concentration of 0–32 vol %. The experiments included tensile tests, notched Izod impact tests, scanning electron microscopy, and dynamic mechanical analysis. Scanning electron microscopy showed that the elastomer and CaCO₃ particles dispersed separately in the matrix. The modulus of the composites increased, whereas the yield stress decreased with the filler concentration. The impact resistance showed a large improvement with the CaCO₃ concentration. At the same composition (80/10/10 w/w/w), three types of CaCO₃ particles with average diameters of 0.05, 0.6, and 1.0 μm improved the impact fracture energies comparatively. The encapsulation structure of the filler by the grafting elastomer had a detrimental effect on the impact properties because of the strong adhesion between the elastomer and filler and the increasing ligament thickness. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1113–1123, 2005     

Morphology and non-isothermal crystallization of dynamically vulcanized PP/EPDM blends in situ compatibilized via magnesium dimethacrylate

Polypropylene/ethylene-propylene-diene rubber (PP/EPDM) blends in situ compatibilized by magnesium dimethacrylate (MDMA) were fabricated via peroxide-induced dynamic vulcanization. Scanning electron microscope observation indicated that the size of cross-linked EPDM particles decreased with incorporation of MDMA. Polarizing Optical Microscope (POM) analysis suggested that the spherulite size of PP phase decreased sharply with incorporation of MDMA during dynamic vulcanization. The Pseudo-Avrami, Ozawa and Mo's models were applied to analyze the non-isothermal crystallization kinetics of the composites. The analyzed data indicated that the crosslinked EPDM particles and homopolymerized MDMA acted as heterogeneous nucleating agents, which enhanced the crystallizability and decreased the spherulite size of the PP phase. In addition, the non-isothermal crystallization activation energy (ΔE) was calculated through the Kissinger and Friedman methods, and the ΔE value was found increase with incorporation of MDMA.     

Dynamic mechanical and thermal properties of physically compatibilized natural rubber/poly(methyl methacrylate) blends by the addition of natural rubber‐graft‐ poly(methyl methacrylate)

The dynamic mechanical and thermal properties of natural rubber/poly (methyl methacrylate) blends (NR/PMMA) with and without the addition of graft copolymer (NR‐g‐PMMA) have been investigated. Dynamic mechanical spectroscopy is used to examine the effect of compatibilizer loading on storage modulus (E′), loss modulus (E″) and loss tangent (tan δ) at different temperatures and at different frequencies. The morphology of the blends indicates that the size of the dispersed phase decreased by the addition of a few percent of the graft copolymer followed by a leveling off at higher concentrations. This is an indication of interfacial saturation. Attempts have been made to correlate morphology with dynamic mechanical properties. Various models have been used to fit the experimental viscoelastic results. Differential scanning calorimetry has been used to analyze the glass‐transition temperatures of the blends. The thermal stability of the blends has been analyzed by thermogravimetry. Compatibilized blends are found to be more thermally stable than uncompatibilized blends. Finally the miscibility and mechanical properties of the blends annealed above T_g are evaluated. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 525–536, 2000     

Thermoplastic elastomer based on epoxidized natural rubber/thermoplastic polyurethane blends: influence of blending technique

Epoxidized natural rubber (ENR) and thermoplastic polyurethane (TPU) blends were prepared by simple blend and dynamic vulcanization. The main objective was to prepare a low‐hardness TPU material with good damping and elastic and mechanical properties. It was found that the incorporation of ENR into the blend shows a reduction in Young's modulus, hardness (i.e. <70 Shore A), damping properties (i.e. tan δ < 0.3), and tension set (i.e. <20%) compared with the pure TPU. This indicates the formation of softer TPU materials with superior damping and elastomeric properties. However, incorporation of ENR sacrificed mechanical properties in terms of tensile strength and elongation at break, but these still remain in the range of applicability for industrial uses. It was also found that dynamic vulcanization caused enhancement of mechanical properties, relaxation, damping, rheological properties, and elasticity of the blends. Temperature scanning stress relaxation measurements revealed an improvement in stress relaxation properties and thermal resistance of the dynamically cured ENR/TPU blend. Copyright © 2011 John Wiley & Sons, Ltd.     

Dynamically cured natural rubber/EVA blends: influence of NR‐g‐poly(dimethyl (methacryloyloxymethyl)phosphonate) compatibilizer

Graft copolymer of natural rubber and poly(dimethyl(methacryloyloxymethyl)phosphonate) (NR‐g‐PDMMMP) was prepared in latex medium via photopolymerization. It was then used to promote the blend compatibility of dynamically cured 40/60 natural rubber (NR)/ethylene vinylacetate copolymer (EVA) blends using various loading levels at 1, 3, 5, 7, 9, 12, and 15 wt%. It was found that the increasing loading levels of NR‐g‐PDMMMP in the blends caused the increasing elastic modulus and complex viscosity until reaching the maximum values at a loading level of 9 wt%. The properties thereafter decreased with the increasing loading levels of NR‐g‐PDMMMP higher than 9 wt%. The smallest vulcanized rubber particles dispersed in the EVA matrix with the lowest tan δ value was also observed at a loading level of 9 wt%. Furthermore, the highest tensile strength and elongation at break (i.e., 17.06 MPa and 660%) as well as the lowest tension set value (i.e., 27%) were also observed in the blend using this loading level of the compatibilizer. Addition of NR‐g‐PDMMMP in the dynamically cured NR/EVA blends also improved the thermal stability of the blend. That is, the decomposition temperature increased with the addition of the graft copolymer. However, the addition of NR‐g‐PDMMMP in the blends caused the decreasing degree of crystallinity of the EVA phase in the blend. However, the strength properties of the blend are still high because of the compatibilizing effect. Copyright © 2009 John Wiley & Sons, Ltd.     

Mechanical and fracture behavior of polypropylene/poly(ethylene-co-vinyl alcohol) blends compatibilized with ionomer Na

In this work the deformation and fracture behavior of PP/EVOH blends compatibilized with ionomer Na⁺ at room and low temperature was studied. Uniaxial tensile tests on dumb-bell samples and fracture tests on single-edge notched bending (SENB) specimens were performed for 10 wt.% and 20 wt.% EVOH blends with different ionomer content at 23 °C and −20 °C. The incorporation of EVOH to PP led to less ductile materials in tension as judged by the lower values of the ultimate tensile strain displayed by all PP/EVOH blends in comparison to neat PP. In contrast, the ionomer Na⁺ addition partially counteracted this effect. The compatibilizing effect of ionomer Na⁺ was also evident in fracture results since higher values of the fracture parameter were obtained for the ternary blends. SEM observations also confirmed this effect. On the other hand, PP/EVOH blends exhibited different fracture behavior with test temperature. All blends showed “pseudo stable” behavior at room temperature characterized by apparently stable crack growth that could not be externally controlled. On the contrary, blends behaved as semi-brittle at −20 °C with some amount of stable crack growth preceding unstable brittle fracture. Finally, irrespectively of the temperature or the ionomer content all PP/EVOH blends exhibited more ductile fracture behavior with a higher tendency to stable crack propagation than neat polypropylene.     

Physico-Mechanical Characteristics of Some EPDM/Plasticized PVC Blends

Summary: In this study were prepared blends based on ethylene propylene terpolymer rubber (EPDM) and plasticized poly (vinyl chloride) (PVC). These blends are immiscible and need to be compatibilized. The following compatibilization methods were used: (1) addition of a compatibilization agent; there were used: maleinized EPDM, maleinized polyethylene (PE), chlorinated polyethylene (CPE) and maleinized polypropylene (PP); chlorinated polyethylene has proved to be the most efficient; the amount of the added CPE giving the best physico-mechanical characteristics was of 7,5 parts to 100 polymer parts; (2) reactive compatibilization, using crosslinked copolymer formation strategy; three different crosslinking systems were used: (a) common method with sulphur and accelerators, (b) crosslinking with benzoyl peroxide and trimethylpropane trimethacrylate (TMPT DL 75), (c) vulcanization with phenol resin and tin chloride. The best physico-mechanical characteristics were obtained with the EPDM/plasticized PVC blends crosslinked with 8 phr phenol resin. Such types of polymer blends can be processed by methods specific for plastics, removing thus vulcanization operation required in case of elastomers. These blends can be used in the manufacture of hoses, gaskets, footwear constituents etc.     

Influence of size reduction of crosslinked rubber particles on phase interface in dynamically vulcanized poly (vinylidene fluoride)/silicone rubber blends

In this paper, the influence of rubber particle size on the phase interface in dynamically vulcanized poly(vinylidene fluoride)/silicone rubber (PVDF/SR) blends without any modifier is discussed through the studies of specific surface of crosslinked SR particles, crystallization behavior and crystal morphology of the PVDF phase, interfacial crystallization, melt rheological behavior and mechanical properties of blends. A series of decreased average particle size was successfully obtained by control of rotor rate. It was found that properly high rotor rate helped to achieve a reduced particle size and a narrowing size distribution. The reduced SR particle size enlarged the PVDF/SR interface which has a positive effect on the interfacial crystallization and the melt rheological behavior. At high SR content, the negative effect of the poor interface interactions played the dominate role on determining the mechanical properties. However, the blend exhibited a unique stiffness-toughness balance at the PVDF/SR = 90/10. We hope that the present study could help to lay a scientific foundation for further design of a useful PVDF/SR blend with promoted properties to partly replace the high-cost synthetic fluorosilicone materials.     

Polypropylene/polystyrene blends: In situ compatibilization by Friedel‐Crafts alkylation reaction

The application of Friedel‐Crafts alkylation reaction to the compatibilization of polypropylene (PP)/polystyrene (PS) blends was assessed. A PP macrocarbocation is chemically bonded to the PS benzene ring by aromatic electrophilic substitution. The graft copolymer formed at the interphase (PP‐g‐PS) showed relatively high emulsification strength, suggesting an effective behavior as in situ compatibilizer. The critical micelle concentration (CMC) was related to Friedel‐Crafts catalyst concentration. The amount of PS grafting and possible appearance of crosslinking and chain scission side reactions were also analyzed. The reaction products were characterized by a combination of size exclusion chromatography and Fourier transform infrared techniques applied after a careful solvent extraction separation. It was found, from the emulsification curve, that CMC was achieved when 0.7 wt % AlCl₃ was added. This value was confirmed by scanning electron microscopy observation of phase adhesion on fractured sample surfaces. Mass balances of extracted PS showed that at least 15 wt % of the initial PS resulted grafted at the CMC condition. Chain scission reactions, in parallel with grafting, were verified to occur for PP as well as for PS. Instead, crosslinking reactions were not detected. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 452–462, 2004     

Compatibilized blends of thermoplastic polyurethane (TPU) and polypropylene

Compatibilized blends of thermoplastic polyurethane (TPU) and polypropylene (PP) were developed using amine (primary or secondary) functionalized PP's (PP-g-NH₂ or PP-g-NHR). The strategy of reactive compatibilization is based on fast reactions between amine functional groups and urethane linkages or traces of free isocyanates released by thermal degradation of TPU. Excellent compatibilization between TPU and PP was confirmed by rheological, morphological, and mechanical properties. Much finer domain size, higher interfacial adhesion, and more stable morphologies were clearly observed by scanning electron microscopy. Significant improvements in the overall mechanical properties (tensile, tear, abrasion) imply significantly more reaction between TPU and PP phases in the two TPU/PP blends containing PP-g-NH₂ or PP-g-NHR than a TPU/PP blend using PP-g-MA as a compatibilizing agent.     

Foaming behavior of polypropylene/polystyrene blends enhanced by improved interfacial compatibility

A series of polypropylene (PP)/polystyrene (PS) blends were prepared by solvent blending with PS‐grafted PP copolymers (PP‐g‐PS) having different PS graft chain length as compatibilizers. The interfacial compatibility was significantly improved with increasing PS graft chain length until the interface was saturated at PS graft chain length being 3.29 × 10³ g/mol. The blends were foamed by using pressure‐quenching process and supercritical CO₂ as the blowing agent. The cell preferentially formed at compatibilized interface because of low energy barrier for nucleation. Combining with the increased interfacial area, the compatibilized interface lead to the foams with increased cell density compared to the uncompatibilized one. The increase in interfacial compatibility also decreased the escape of gas, held more gas for cell growth, and facilitated the increase in expansion ratio of PP/PS blend foams. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1641–1651, 2008     

Compatibilization of polypropylene/poly (ethylene oxide) blends and crystallization behavior of the blends

The compatibilization of incompatible polypropylene (PP)/poly(ethylene oxide) (PEO) blends was studied. The experimental results showed that the graft copolymer [(PP-MA)-g-PEO] of maleated PP(PP-MA) and mono-hydroxyl PEO (PEO-OH) was a good compatibilizer for the PP/PEO blends in which PP-MA also had some compatibilization. The crystallization of the blends was affected by the compatibility between PP and PEO. The interfacial behavior of the compatibilizers had an important effect on crystallization behavior of the PP/PEO blends. PEO showed fractionated crystallization in the PP/PEO blends. This behavior was studied from the view point of the theory of fractionated crystallization. © 1994 John Wiley & Sons, Inc.     

Ternary blends based on poly (ethylene-naphthalate)/glass fibers/nitrile rubber: Preparation,properties and effect of dynamic vulcanization

This work studied the possibility of utilizing nitrile rubber (NBR) to modify the impact properties of poly (ethylene-naphthalate) (PEN). The PEN/NBR ratio used changed from 100/0 to 60/40. At the same time, glass fibers (GF), 40% weight of the PEN component, were used to reinforce the blends to compensate for the loss of mechanical properties of PEN by incorporation of NBR. The results showed that the impact strength of the PEN/GF/NBR blend (PEN/NBR = 60/40) was increased up to 27.6J/m, nearly 5 times higher than that of the neat PEN. Meanwhile, the tensile strength and flexural strength were still maintained at as high as 66.1 MPa and 98.2 MPa, respectively. Dynamic vulcanization further improved the mechanical properties of the PEN/GF/NBR blends, which provided routes to the design of new PEN/elastomer blends. Other properties of the PEN/GF/NBR blends were also investigated in terms of morphology of fractured surface, dynamic mechanical behavior, thermal stability and crystallization, by scanning electron microscopy (SEM), dynamic mechanical analysis (DMA), thermo-gravimetric analysis (TGA) and differential scanning calorimetry (DSC), respectively.